Determination of Melamine in Dairy Products and Melamine Tableware by Inhibition Electrochemiluminescent Method

An electrochemiluminescent (ECL) method has been developed for the determination of melamine based on the inhibition of luminol ECL. A significant luminol ECL can be found at 1.47 V in the phosphate buffer solution at high pHs and low potential scan rates, this ECL signal can be inhibited obviously by melamine. The decrease of ECL intensity was linearly proportional to the logarithm of melamine concentration in the range of 1–100 ng/mL (R²=0.9911) and with the detection limit of 0.1 ng/mL. The method has been applied successfully to determine melamine in dairy products and melamine tableware, the recoveries were in the range of 98.5%–103.7% and 95.5%–106.0%, respectively. The mechanism of the inhibition effect was also proposed, the active oxygen (O₂^{· −}) generated from the electrooxidation of OH⁻ reacted with luminol anion (L^{· −}) to generate light emission, and the present of melamine can eliminate the active oxygen, which cause the decrease of the ECL intensity.     

Development of an ultrasensitive electrochemiluminescence inhibition method for the determination of tetracyclines

An electrochemiluminescence (ECL) inhibition method is developed for quantitative determination of four tetracyclines (TCs) in honey samples, including tetracycline (TC), oxytetracycline (OTC), chlortetracycline (CTC) and doxycycline (DC). It was found that the four TCs strongly inhibited the ECL signal of the Ru(bpy)₃²⁺/DBAE system. Based on the ECL signal changes, a simple and ultrasensitive detection method for TCs was thus established. The optimum experimental conditions including the scan mode and scan rate of the applied potential, the type of the buffer solution and its pH, and the concentration of Ru(bpy)₃²⁺ and DBAE for the ECL inhibition method, were investigated in detail. Under the optimized conditions, the quenched ECL intensity versus the logarithm of the concentration of TCs is in good linear relationship over a concentration range from 4.0 × 10⁻¹¹ to 4.0 × 10⁻⁹ g mL⁻¹. The detection limits were found to be 2.0 × 10⁻¹² g mL⁻¹. The results obtained by the proposed ECL system, in terms of sensitivity, were much better than those of previously reported methods. In addition, the method was applied successfully to determine the total residuals of the four TCs in honey samples. The relative standard deviations were found in a range of 4.9–14.3%, and the recoveries were obtained from 87.5% to 115.0%. A possible mechanism for the quenching effects of Ru(bpy)₃²⁺/DBAE system was also proposed.     

Silver(I) ions-enhanced electrochemiluminescence of tris(2,2-bipyridyl)ruthenium(II)

In this paper, we demonstrate an electrochemiluminescence (ECL) enhancement of tris(2,2-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) by the addition of silver(I) ions. The maximum enhancement factor of about 5 was obtained on a glassy carbon electrode in the absence of co-reactant. The enhancement of ECL intensity was possibly attributed to the unique catalytic activity of Ag⁺ for reactions between Ru(bpy)₃³⁺ with OH. The higher enhancement was observed in phosphate buffer solutions compared with that from borate buffer solutions. This resulted from the fact that formation of nanoparticles with large surface area in the phosphate buffer solution exhibited high catalytic activity. The amount of Ag⁺, solution pH and working electrode materials played important roles for the ECL enhancement. We also studied the effects of Ag⁺ on Ru(bpy)₃²⁺/tripropylamine and Ru(bpy)₃²⁺/C₂O₄²⁻ ECL systems.     

Electrochemiluminescence from tris(2,2′-bipyridyl)ruthenium(II)-graphene-Nafion modified electrode

An electrochemiluminescence (ECL) sensor based on Ru(bpy)₃²⁺-graphene-Nafion composite film was developed. The graphene sheet was produced by chemical conversion of graphite, and was characterized by atomic force microscopy (AFM), scanning electron microscopy (SEM), and Raman spectroscopy. The introduction of conductive graphene into Nafion not only greatly facilitates the electron transfer of Ru(bpy)₃²⁺, but also dramatically improves the long-term stability of the sensor by inhibiting the migration of Ru(bpy)₃²⁺ into the electrochemically inactive hydrophobic region of Nafion. The ECL sensor gives a good linear range over 1 × 10⁻⁷ to 1 × 10⁻⁴ M with a detection limit of 50 nM towards the determination of tripropylamine (TPA), comparable to that obtained by Nafion-CNT. The ECL sensor keeps over 80% and 85% activity towards 0.1 mM TPA after being stored in air and in 0.1 M pH 7.5 phosphate buffer solution (PBS) for a month, respectively. The long-term stability of the modified electrode is better than electrodes modified with Nafion, Nafion-silica, Nafion-titania, or sol-gel films containing Ru(bpy)₃²⁺. Furthermore, the ECL sensor was successfully applied to the selective and sensitive determination of oxalate in urine samples.     

十二烷基磺酸钠-盐酸维拉帕米-联吡啶钌体系电化学发光及其应用

在十二烷基磺酸钠(SDS)中,考察了盐酸维拉帕米-Ru(bpy)3(2+)体系在金电极上的电化学及其发光行为.结果表明:SDS对体系的电化学反应和电化学发光强度具有显著的增敏作用.据此,建立了一种高效、简便的测定盐酸维拉帕米的电化学发光新方法.在最佳实验条件下,盐酸维拉帕米浓度在1.0×10(-4)～1.0×10(-2...     

Disposable biosensor based on cathodic electrochemiluminescence of tris(2,2-bipyridine)ruthenium(II) for uric acid determination

A new method for uric acid (UA) determination based on the quenching of the cathodic ECL of the tris(2,2-bipyridine)ruthenium(II)–uricase system is described. The biosensor is based on a double-layer design containing first tris(2,2-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) electrochemically immobilized on graphite screen-printed cells and uricase in chitosan as a second layer. The uric acid biosensing is based on the ECL quenching produced by uric acid over the cathodic ECL caused by immobilized Ru(bpy)₃²⁺ in the presence of uricase. The use of a −1.1 V pulse for 1 s with a dwelling time of 10 s makes it possible to estimate the initial enzymatic rate, which is used as the analytical signal. The Stern–Volmer type calibration function shows a dynamic range from 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M with a limit of detection of 3.1 × 10⁻⁶ M and an accuracy of 13.6% (1.0 × 10⁻⁴ M, n = 5) as relative standard deviation. Satisfactory results were obtained for urine samples, creating an affordable alternative for uric acid determination.     

Determination of itopride hydrochloride by high-performance liquid chromatography with Ru(bpy)3 electrogenerated chemiluminescence detection

In this work, a stable electrogenerated chemiluminescence (ECL) detector was developed. The detector was prepared by packing cation-exchanged resin particles in a glass tube, followed by inserting Pt wires (working electrode) in this tube and sealing. The leakage of Ru(bpy)₃²⁺ can be compensated by adding a small amount of Ru(bpy)₃²⁺ into solution phase. Coupled with high-performance liquid chromatography separation, the detector has been used for determination of itopride hydrochloride in human serum. Under the optimal conditions, the ECL intensity has a linear relationship with the concentration of itopride hydrochloride in the range of 1.0 × 10⁻⁸ g mL⁻¹ to 1.0 × 10⁻⁶ g mL⁻¹ and the detection limit was 3 × 10⁻⁹ g mL⁻¹ (S/N = 3). The as-prepared ECL detector displayed good sensitivity and stability.     

Flow injection analysis of gallic acid with inhibited electrochemiluminescence detection

A flow injection (FI)–electrochemiluminescent (ECL) method has been developed for the determination of gallic acid, based on an inhibition effect on the Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) ECL system in pH 8.0 phosphate buffer solution. The method is simple and convenient with a determination limit of 9.0×10^–9 mol/L and a dynamic concentration range of 2×10^–8–2×10^–5 mol/L. The relative standard deviation (RSD) was 1.0% for 1.0×10^–6 mol/L gallic acid (n=11). It was successfully applied to the determination of gallic acid in Chinese proprietary medicine—Jianming Yanhou Pian. The inhibition mechanism proposed for the quenching effect of the gallic acid on the Ru(bpy)₃²⁺/TPrA ECL system was the interaction of electrogenerated Ru(bpy)₃^2+* and o-benzoquinone derivative at the electrode surface. The ECL emission spectra and UV-visible absorption spectra were applied to confirm the mechanism.     

Molecularly imprinted polymer as SPE sorbent for selective extraction of melamine in dairy products

In this paper, a highly selective sample cleanup procedure combining molecular imprinting and solid-phase extraction (MI-SPE) was developed for the isolation of melamine in dairy products. The molecularly imprinted polymer (MIP) was prepared using melamine as the template molecule, methacrylic acid as the functional monomer and ethylene glycol dimethacrylate as the cross-linking monomer. The melamine imprinted polymer was used as selective sorbent for the solid-phase extraction of melamine from dairy products. An off-line MI-SPE method followed by high-performance liquid chromatography with diode-array detection for the detection of melamine was also established. The mean recoveries of melamine from ultra-heat treatment (UHT) milk and milk powders were 92.9-98.0% and 91.6-102.8%, respectively. Good linearity was obtained from 0.5 μM to 10 μM (r > 0.999) with a quantitation limit of 0.5 μmol/L (0.06 ppm) which was sufficient to analyse melamine at the maximum level permitted by U.S. Food and Drug Administration (1 ppm) in dairy products. It was demonstrated that the proposed MI-SPE-HPLC method could be applied to direct determination of melamine in dairy products.     

A new electrochemiluminescent detection system equipped with an electrically controlled heating cylindrical microelectrode

A new electrochemiluminescent (ECL) detection system equipped with an electrically controlled heating cylindrical microelectrode (HME) was developed in this paper. The cylindrical microelectrode made of platinum wire (25 μm in diameter, 6 mm in long) was used as the working electrode of the ECL detection system, the temperature of the electrode could be controlled electrically. The Ru(bpy)₃²⁺-ECL and Ru(bpy)₃²⁺-C₂O₄²⁻-ECL systems were used to evaluate this ECL detection system. The detection limit for oxalate was found to be 3.0 × 10⁻⁴ mol/L when T_e (temperature of the HME) was 22 °C, and found to be 3.0 × 10⁻⁶ mol/L at 80 °C, which indicates that the detection limit can be improved greatly at higher T_e, based on which, it is possible to establish a more sensitive method for measurement of ECL by using a heated microelectrode.     

The role of direct oxalate oxidation in electrogenerated chemiluminescence of poly(4-vinylpyridine)-bound Ru(bpy)2Cl/oxalate system on indium tin oxide electrodes

The electrochemical and electrogenerated chemiluminescence (ECL) properties of indium tin oxide (ITO) electrodes modified with poly(4-vinylpyridine) (PVP)-bound Ru(bpy)₂Cl⁺ (where bpy = 2,2′-bipyridine) have been studied. In a sodium oxalate solution, two irreversible oxidation waves as well as two ECL emission waves were observed during the potential scan in the range 0.4-1.4 V (versus Ag/AgCl/saturated KCl reference). The first ECL wave appeared at ca. 0.8 V, which was caused by the excited-state Ru^2+* generated through a bimolecular redox reaction between electrogenerated Ru³⁺ and the strong reducing agent, C⁻O₂. The latter was formed via a Ru³⁺-mediated oxidation of oxalate. Direct oxidation of oxalate was not involved in the first ECL process. The second ECL wave started at ca. 1.1 V, which was also from the excited-state Ru^2+* generated via the redox reaction between Ru³⁺ and C⁻O₂. However, both direct and Ru³⁺-mediated oxidation of oxalate contributed to the formation of C⁻O₂. The important role of the direct oxidation of oxalate in the ECL mechanism of PVP-bound Ru(bpy)₂Cl⁺/oxalate system was demonstrated. The relative contribution of direct oxidation of oxalate to the observed ECL depended upon the surface concentration of PVP-bound Ru²⁺, the concentration of oxalate and the electrode potential applied.     

Determination of imipramine and trimipramine by capillary electrophoresis with electrochemiluminescence detection

The tricyclic antidepressants (TCA) imipramine (Imi) and trimipramine (Tri) were successfully analyzed by capillary electrophoresis (CE) coupling with Tris(2,2-bipyridyl) ruthenium(II)-based (Ru(bpy)₃²⁺) end-column electrochemiluminescence (ECL) detection. The addition of β-CD to the running buffer was found to enable baseline separation of the two analytes and the addition of acetonitrile (ACN) as an organic additive to improve the repeatability and sensitivity of the CE method. Under the optimized separation and detection conditions (50 mM PBS (pH = 7.0) and 2 mM Ru(bpy)₃²⁺ in the ECL detection cell, 20 mM Tris (pH = 2.0), 0.2 mM β-CD and 20% ACN (v/v) as running buffer), wide linear ranges of 0.1-5 μM and 0.1-5 μM were achieved, with the correlation coefficients of 0.9990 (n = 8) and 0.9980 (n = 8) for Imi and Tri, respectively. Detection limits 5 nM and 1 nM (S/N = 3) were obtained for Imi and Tri, respectively. The method was also successfully applied for the determination of Imi in pharmaceutical dosage form.     

玻碳电极上Ru(bpy)32+的吸附及其电致化学发光的研究

通过电化学循环伏安法和电致化学发光方法, 研究了Ru(bpy)₃²⁺在玻碳电极上的吸附, 研究结果表明, Ru(bpy)₃²⁺的浓度和与玻碳材料接触的时间, 直接影响了Ru(bpy)₃²⁺在玻碳上的吸附. 还考察了吸附的 在玻碳电极上被氧化后脱附的情况.     

Magnetically assisted solid phase extraction using Fe3O4 nanoparticles combined with enhanced spectrofluorimetric detection for aflatoxin M1 determination in milk samples

A novel, facile and inexpensive solid phase extraction (SPE) method using ethylene glycol bis-mercaptoacetate modified 3-(trimethoxysilyl)-1-propanethiol grafted Fe₃O₄ nanoparticles coupled with spectrofluorimetric detection was proposed for determination of aflatoxin M1 (AFM1) in liquid milk samples. The method uses the advantage fluorescence enhancement by β-cyclodexterin complexation of AFM1 in 12% (v/v) acetonitrile–water and the remarkable properties of Fe₃O₄ nanoparticles namely high surface area and strong magnetization were utilized to achieve high enrichment factor (57) and satisfactory extraction recoveries (91–102%) using only 100 mg of magnetic adsorbent. Furthermore, fast separation time of about 15 min avoids many time-consuming column-passing procedures of conventional SPE. The main factors affecting extraction efficiency including pH value, desorption conditions, extraction/desorption time, sample volume, and adsorbent amount were evaluated and optimized. Under the optimal conditions, a wide linear range of 0.04–8 ng mL⁻¹ with a low detection limit of 0.015 ng mL⁻¹ was obtained. The developed method was applied for extraction and preconcentration of AFM1 in three commercially available milk samples and the results were compared with the official AOAC method.     

Sensitive determination of verticine and verticinone in Bulbus Fritillariae by ionic liquid assisted capillary electrophoresis-electrochemiluminescence system

CE/Ru(bpy)₃²⁺ electrochemiluminescence (ECL) system with the assistance of ionic liquids (ILs) was successfully established for sensitive determination of verticine and verticinone in Bulbus Fritillariae for the first time. Migration behavior of alkaloid largely relies on the hydrogen bonding interactions between alkyl imidazolium cations in ILs and the alkaloids. Running buffer containing 40 mmol/L 1-butyl-3-methylimidazolium tetrafluoroborate (BMImBF₄) IL-8 mmol/L phosphate resulted in significant changes in separation selectivity for alkaloids with similar structures. The highest sensitivity of the detection was obtained by maintaining the detection potential at 1.2 V. Under the optimized conditions, relative standard derivations of the ECL intensity and the migration time were 3.27 and 2.84% for verticine and 4.42 and 1.69% for verticinone, respectively. The standard curves were linear between 1 × 10⁻⁸ and 1 × 10⁻⁶ mol/L for verticine and between 5 × 10⁻⁸ and 1 × 10⁻⁶ mol/L for verticinone, respectively. Detection limits of 1.25 × 10⁻¹⁰ mol/L for verticine and 1 × 10⁻¹⁰ mol/L for verticinone were obtained (S/N = 3). Developed method was successfully applied to determine the amounts of alkaloids in Bulbus Fritillariae.     

Tris(2,2′-bipyridyl)ruthenium(II) electrogenerated chemiluminescence sensor based on carbon nantube dispersed in sol-gel-derived titania-Nafion composite films

A highly sensitive and stable tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy)₃²⁺ immobilized in the ECL sensor by adsorption of Ru(bpy)₃²⁺ onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-titania-Nafion showed improved ECL sensitivity for tripropylamine (TPA) compared to the ECL sensors based on both titania-Nafion composite films without CNT and pure Nafion films. The present Ru(bpy)₃²⁺ ECL sensor based on the MWCNT-titania--Nafion composite gave a linear response (R² = 0.999) for TPA concentration from 50 nM to 1.0 mM with a remarkable detection limit (S/N = 3) of 10 nM while the ECL sensors based on titania-Nafion composite without MWCNT, pure Nafion films, and MWCNT-Nafion composite gave a detection limit of 0.1 μM, 1 μM, and 50 nM, respectively. The present ECL sensor showed outstanding long-term stability (no signal loss for 4 months).     

Rapid detection of melamine with 4-mercaptopyridine-modified gold nanoparticles by surface-enhanced Raman scattering

A surface-enhanced Raman scattering (SERS) strategy based on 4-mercaptopyridine (MPY)-modified gold nanoparticles (AuNPs) was developed for the rapid and sensitive detection of melamine in milk powder. The SERS measurement of melamine strongly relied on the “hotspot” effect, in which AuNPs immediately aggregated upon the addition of melamine, leading to significantly enhanced Raman intensity of the reporter molecule MPY and a color change for the solution from red to blue-gray. The limit of detection based on a signal to noise of 3 (S/N = 3) was found to be as low as 0.1 ppb of melamine, with an excellent linearity of 0.5–100 ppb, demonstrating a higher sensitivity and a wider quantitation range than direct SERS sensing methods based on enhanced substrate. An impressive specificity for melamine detection over various common metal ions and excipients in dairy products, even at concentrations of 100-fold higher than melamine, was achieved. Good recoveries of 88.5% and 111.7% were obtained from milk samples spiked to 20 and 100 ppb levels, respectively. The proposed method is potentially applicable for the rapid in situ determination of melamine in complex matrices.     

High electrochemiluminescence intensity of the Ru(bpy)3 2+/oxalate system on a platinum net electrode

A new method for enhancing the electrochemiluminescence (ECL) intensity of the Ru(bpy)₃ ²⁺/ oxalate system is presented. When a platinum net was used as a working electrode and a platinum foil as an auxiliary electrode, the ECL intensity of the system was enhanced greatly. In addition, a cathodic peak appeared at 0.18 V (vs. SCE) on a platinum net electrode, and ECL of the system was observed at 0.18 V.     

Determination of melamine in different milk batches using a novel chemosensor based on the luminescence quenching of Ru(II) carbonyl complex

A novel, simple, sensitive and precise spectrofluorimetric method was developed for measuring the melamine concentration in different milk batch samples. The method was based upon measuring the quenching of the luminescence intensity of the produced yellow colored ruthenium^(II) carbonyl complex of the general formula [Ru(CO)₂(L)] (where L = anion of tetradentate Schiff base). The Ru^(II) complex exhibited characteristic luminescence band in the visible region. The remarkable quenching of the luminescence intensity of [Ru(CO)₂(L)] complex by various concentrations of melamine was successfully used as a chemosensor for the assessment of melamine in different milk samples at λ_ex = 400 nm and pH 7.4 in DMSO with a linear dynamic range 1.0 × 10⁻⁶ to 3.0 × 10⁻⁹ mol L⁻¹ and lower detection limit (LOD) and quantification detection limit (QOD) of 3.3 × 10⁻¹⁰ and 1.0 × 10⁻⁹ mol L⁻¹, respectively.     

Mechanism study on inorganic oxidants induced inhibition of Ru(bpy)₃²+ electrochemiluminescence and its application for sensitive determination of some inorganic oxidants

Inhibited Ru(bpy)₃²⁺ electrochemiluminescence by inorganic oxidants is investigated. Results showed that a number of inorganic oxidants can quench the ECL of Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) system, and the logarithm of the decrease in ECL intensity (ΔI) was proportional to the logarithm of analyte concentrations. Based on which, a sensitive approach for detection of these inorganic oxidants was established, e.g. the log-log plots of ΔI versus the concentration of MnO₄⁻, Cr₂O₇²⁻ and Fe(CN)₆³⁻ are linear in the range of 1 × 10⁻⁷ to 3 × 10⁻⁴ M for MnO₄⁻ and Cr₂O₇²⁻, and 1 × 10⁻⁷ to 1 × 10⁻⁴ M for Fe(CN)₆³⁻, with the limit of detection (LOD) of 8.0 × 10⁻⁸ M, 2 × 10⁻⁸ M, and 1 × 10⁻⁸ M, respectively. A series of experiments such as a comparison of the inhibitory effect of different compounds on Ru(bpy)₃²⁺/TPrA ECL, ECL emission spectra, UV-Vis absorption spectra etc. were investigated in order to discover how these inorganic analytes quench the ECL of Ru(bpy)₃²⁺/TPrA system. A mechanism based on consumption of TPrA intermediate (TPrA^·) by inorganic oxidants was proposed.