Macroscale Chemotaxis from a Swarm of Bacteria‐Mimicking Nanoswimmers

Inspired by the dynamics of bacterial swarming, we report a swarm of polymer‐brush‐grafted, glucose‐oxidase‐powered Janus gold nanoswimmers with a positive, macroscale chemotactic behavior. These nanoswimmers are prepared through the grafting of polymer brushes onto one side of gold nanoparticles, followed by functionalization with glucose oxidase on the other side. The resulting polymer‐brush‐functionalized Janus gold nanoswimmers exhibit efficient propulsion with a velocity of up to approximately 120 body lengths s^?1 in the presence of glucose. The comparative analysis of their kinematic behavior reveals that the grafted polymer brushes significantly improve the translational diffusion of Janus gold nanoswimmers. Particularly, these bacteria‐mimicking Janus gold nanoswimmers display a collectively chemotactic motion along the concentration gradient of a glucose resource, which could be observed at the macroscale.     

Micromotor‐Based Energy Generation

A micromotor‐based strategy for energy generation, utilizing the conversion of liquid‐phase hydrogen to usable hydrogen gas (H₂), is described. The new motion‐based H₂‐generation concept relies on the movement of Pt‐black/Ti Janus microparticle motors in a solution of sodium borohydride (NaBH₄) fuel. This is the first report of using NaBH₄ for powering micromotors. The autonomous motion of these catalytic micromotors, as well as their bubble generation, leads to enhanced mixing and transport of NaBH₄ towards the Pt‐black catalytic surface (compared to static microparticles or films), and hence to a substantially faster rate of H₂ production. The practical utility of these micromotors is illustrated by powering a hydrogen–oxygen fuel cell car by an on‐board motion‐based hydrogen and oxygen generation. The new micromotor approach paves the way for the development of efficient on‐site energy generation for powering external devices or meeting growing demands on the energy grid.     

Chemical/Light‐Powered Hybrid Micromotors with “On‐the‐Fly” Optical Brakes

Hybrid micromotors capable of both chemically powered propulsion and fuel‐free light‐driven actuation and offering built‐in optical brakes for chemical propulsion are described. The new hybrid micromotors are designed by combining photocatalytic TiO₂ and catalytic Pt surfaces into a Janus microparticle. The chemical reactions on the different surfaces of the Janus particle hybrid micromotor can be tailored by using chemical or light stimuli that generate counteracting propulsion forces on the catalytic Pt and photocatalytic TiO₂ sides. Such modulation of the surface chemistry on a single micromotor leads to switchable propulsion modes and reversal of the direction of motion that reflect the tuning of the local ion concentration and hence the dominant propulsion force. An intermediate Au layer (under the Pt surface) plays an important role in determining the propulsion mechanism and operation of the hybrid motor. The built‐in optical braking system allows “on‐the‐fly” control of the chemical propulsion through a photocatalytic reaction on the TiO₂ side to counterbalance the chemical propulsion force generated on the Pt side. The adaptive dual operation of these chemical/light hybrid micromotors, associated with such control of the surface chemistry, holds considerable promise for designing smart nanomachines that autonomously reconfigure their propulsion mode for various on‐demand operations.     

Polyelectrolyte brushes as efficient platform for synthesis of Cu and Pt bimetallic nanocrystals onto TiO2 nanowires

A Cu–Pt nanoparticle catalyst supported on TiO₂ nanowires (NWs) was prepared through regenerative counterion exchange–reduction using polyelectrolyte brush as template. Cationic polydimethyl aminoethyl methacrylate brushes were grafted onto TiO₂ NWs. Cu–Pt nanocrystals were produced by anionic counterions CuCl₄^2? and PtCl₆^2? bound with the polymer brush through in situ reduction with NaBH₄ of high density and low polydispersity. The as‐prepared TiO₂ NWs/polymer brush/Cu–Pt was characterized by Fourier transform infrared spectroscopy (FT‐IR spectrometry), X‐ray photoelectron spectroscopy, transmission electron microscopy, and UV–Vis adsorption spectrometry analyses. Results showed that the highly dispersed Cu and Pt nanoparticles were present on the surface of the TiO₂ NWs/polymer brush. The resultant TiO₂ NWs/polymer brush/Cu–Pt exhibited extremely high catalytic activity and reduced p‐nitrophenol at room temperature. Copyright © 2017 John Wiley & Sons, Ltd.     

Double‐Stimuli‐Responsive Spherical Polymer Brushes with a Poly(ionic liquid) Core and a Thermoresponsive Shell

The synthesis of poly(ionic liquid) (PIL) nanoparticles grafted with a poly(N‐isopropyl acrylamide) (PNIPAM) brush shell is reported, which shows responsiveness to temperature and ionic strength in an aqueous solution. The PIL nanoparticles are first prepared via aqueous dispersion polymerization of a vinyl imidazolium‐based ionic liquid monomer, which is purposely designed to bear a distal atom transfer radical polymerization (ATRP) initiating group attached to the long alkyl chain via esterification reaction. The size of the PIL nanoparticles can be readily tuned from 25 to 120 nm by polymerization at different monomer concentrations. PNIPAM brushes are successfully grafted from the surface of the poly(ionic liquid) nanoparticles via ATRP. The stimuli‐responsive behavior of the poly(ionic liquid) nanoparticles grafted with PNIPAM brushes (NP‐g‐PNIPAM) in aqueous phase is studied in detail. Enhanced colloidal stability of the NP‐g‐PNIPAM brush particles at high ionic strength compared to pure PIL nanoparticles at room temperature is achieved. Above the lower critical solution temperature (LCST) of PNIPAM, the brush particles remain stable, but a decrease in hydrodynamic radius due to the collapse of the PNIPAM brush onto the PIL nanoparticle surface is observed.

     

Double‐Layered Plasmonic–Magnetic Vesicles by Self‐Assembly of Janus Amphiphilic Gold–Iron(II,III) Oxide Nanoparticles

Janus nanoparticles (JNPs) offer unique features, including the precisely controlled distribution of compositions, surface charges, dipole moments, modular and combined functionalities, which enable excellent applications that are unavailable to their symmetrical counterparts. Assemblies of NPs exhibit coupled optical, electronic and magnetic properties that are different from single NPs. Herein, we report a new class of double‐layered plasmonic–magnetic vesicle assembled from Janus amphiphilic Au‐Fe₃O₄ NPs grafted with polymer brushes of different hydrophilicity on Au and Fe₃O₄ surfaces separately. Like liposomes, the vesicle shell is composed of two layers of Au‐Fe₃O₄ NPs in opposite direction, and the orientation of Au or Fe₃O₄ in the shell can be well controlled by exploiting the amphiphilic property of the two types of polymers.     

Continuously Variable Regulation of the Speed of Bubble‐Propelled Janus Microcapsule Motors Based on Salt‐Responsive Polyelectrolyte Brushes

The engineering of self‐propelled micro‐/nanomotors (MNMs) with continuously variable speeds, akin to macroscopic automobiles equipped with a continuously variable transmission, is still a huge challenge. Herein, after grafting with salt‐responsive poly[2‐(methacryloyloxy)ethyltrimethylammonium chloride] (PMETAC) brushes, bubble‐propelled Janus microcapsule motors with polyelectrolyte multilayers exhibited adjustable speeds when the type and concentration of the counterion was changed. Reversible switching between low‐ and high‐speed states was achieved by modulating the PMETAC brushes between hydrophobic and hydrophilic configurations by ion exchange with ClO₄^? and polyphosphate anions. This continuously variable regulation enabled control of the speed in an accurate and predictable manner and an autonomous response to the local chemical environment. This study suggests that the integration of polymer brushes with precisely adjustable responsiveness offers a promising route for motion control of smart MNMs that act like their counterparts in living systems.     

Salt‐Induced Depression of Lower Critical Solution Temperature in a Surface‐Grafted Neutral Thermoresponsive Polymer

Summary: Quartz crystal microbalance with dissipation monitoring (QCM‐D) is employed to determine the effect of salt on the volume phase transition of thermoresponsive polymer brushes. Changes in mass and viscoelasticity of poly(N‐isopropylacrylamide) (PNIPAM) layers grafted from a QCM‐D crystal are measured as a function of temperature, upon contact with aqueous solutions of varying salt concentrations. The phase‐transition temperature of PNIPAM brushes, T_C,graft, quantified from the QCM‐D measurements is found to decrease as the concentration of salt is increased. This phenomenon is explained by the tendency of salt ions to affect the structure of water molecules (Hofmeister effect). However, in contrast to the linear decrease in phase‐transition temperature upon increasing salt concentration observed for free PNIPAM, the trend in T_C,graft for PNIPAM brushes is distinctively non‐linear.

Schematic representation of the effect of salt concentration on the phase transition behavior of thermoresponsive polymer brushes.     

Doubly thermoresponsive brush‐linear‐linear ABC triblock copolymer nanoparticles prepared through dispersion RAFT polymerization

Doubly thermoresponsive ABC brush‐linear‐linear triblock copolymer nanoparticles of poly[poly(ethylene glycol) methyl ether vinylphenyl]‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene [P(mPEGV)‐b‐PNIPAM‐b‐PS] containing two thermoresponsive blocks of poly[poly(ethylene glycol) methyl ether vinylphenyl] [P(mPEGV)] and poly(N‐isopropylacrylamide) (PNIPAM) are prepared by macro‐RAFT agent mediated dispersion polymerization. The P(mPEGV)‐b‐PNIPAM‐b‐PS nanoparticles exhibit two separate lower critical solution temperatures or phase‐transition temperatures (PTTs) corresponding to the linear PNIPAM block and the brush P(mPEGV) block in water. Upon temperature increasing above the first and then the second PTT, the hydrodynamic diameter (D_h) of the triblock copolymer nanoparticles undergoes an initial shrinkage at the first PTT and the subsequent shrinkage at the second PTT. The effect of the chain length of the PNIPAM block on the thermoresponsive behavior of the triblock copolymer nanoparticles is investigated. It is found that, the longer chains of the thermoresponsive PNIPAM block, the greater contribution on the transmittance change of the aqueous dispersion of the triblock copolymer nanoparticles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2266–2278     

Solubilization of C60 by micellization with a thermoresponsive block copolymer in water: Characterization,singlet oxygen generation,and DNA photocleavage

Water‐soluble diblock copolymer, poly(N‐isopropylacrylamide)‐block‐poly(N‐vinyl‐2‐pyrroridone) (PNIPAM_m‐b‐PNVP_n), was found to associate with fullerene (C₆₀), and thus C₆₀ can be solubilized in water. The 63C₆₀/PNIPAM_m‐b‐PNVP_n micelle formed a core‐shell micelle‐like aggregate comprising a C₆₀/PNVP hydrophobic core and a thermoresponsive PNIPAM shell. The C₆₀‐containing polymer micelle formation and its thermoresponsive behavior were characterized using light scattering and ¹H NMR techniques. The hydrodynamic radius (R_h) of the C₆₀‐bound polymer micelle increased with increasing temperature, which was ascribed to the hydrophobic association between dehydrated PNIPAM shells above lower critical solution temperature (LCST). ¹H NMR data suggest that the motion of the PNIPAM block is restricted above LCST due to the dehydration of the PNIPAM shell in water. The generation of singlet oxygen by photosensitization by the C₆₀‐bound polymer micelle was confirmed from photooxidation of 9,10‐anthracenedipropionic acid. Furthermore, DNA was found to be cleaved by visible light irradiation in the presence of the C₆₀‐bound polymer micelle. Therefore, there may be a hope for a pharmaceutical application of the C₆₀‐bound polymer micelle to cancer photodynamic therapy. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Effect of chain architecture on the phase transition of star and cyclic poly(N‐isopropylacrylamide) in water

The heat‐induced phase transition of aqueous solutions of Poly(N‐isopropylacrylamide) (PNIPAM) in water is examined for a four‐arm PNIPAM star (s‐PNIPAM), a cyclic PNIPAM (c‐PNIPAM), and their linear counterparts (l‐PNIPAM) in the case of polymers (1.0 g L^?1) of 12,700 g mol^?1 < M_n < 14,700 g mol^?1. Investigations by turbidity, high‐sensitivity differential scanning calorimetry (HS‐DSC), and light scattering (LS) indicate that the polymer architecture has a strong effect on the cloud point (T_c: decrease for s‐PNIPAM; increase for c‐PNIPAM), the phase transition enthalpy change (ΔH decrease for s‐PNIPAM and c‐PNIPAM), and the hydrodynamic radius of the aggregates formed above T_c (R_H: c‐PNIPAM < s‐PNIPAM < l‐PNIPAM). The properties of s‐PNIPAM are compared with those of previously reported PNIPAM star polymers (3 to 52 arms). The overall observations are described in terms of the arm molecular weight and the local chain density in the vicinity of the core of the star, by analogy with the model developed for PNIPAM brushes on nanoparticles or planar surfaces. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2059–2068.     

Tribological properties of hydrophilic polymer brushes under wet conditions

This article demonstrates a water‐lubrication system using high‐density hydrophilic polymer brushes consisting of 2,3‐dehydroxypropyl methacrylate (DHMA), vinyl alcohol, oligo(ethylene glycol)methyl ether methacrylate, 2‐(methacryloyloxy)ethyltrimethylammonium chloride (MTAC), 3‐sulfopropyl methacrylate potassium salt (SPMK), and 2‐methacryloyloxyethyl phosphorylcholine (MPC) prepared by surface‐initiated controlled radical polymerization. Macroscopic frictional properties of brush surfaces were characterized by sliding a glass ball probe in water using a ball‐on‐plate type tribotester under the load of 0.1–0.49 N at the sliding velocity of 10^?5–10^?1 m s^?1 at 298 K. A poly(DHMA) brush showed a relatively larger friction coefficient in water, whereas the polyelectrolyte brushes, such as poly(SPMK) and poly(MPC), revealed significantly low friction coefficients below 0.02 in water and in humid air conditions. A drastic reduction in the friction coefficient of polyelectrolyte brushes in aqueous solution was observed at around 10^?3–10^?2 m s^?1 owing to the hydrodynamic lubrication effect, however, an increase in salt concentration in the aqueous solution led to the increase in the friction coefficients of poly(MTAC) and poly(SPMK) brushes. The poly(SPMK) brush showed a stable and low friction coefficient in water even after sliding over 450 friction cycles, indicating a good wear resistance of the brush film. © 2010 The Japan Chemical Journal Forum and Wiley Periodicals, Inc. Chem Rec 10: 208–216; 2010: Published online in Wiley InterScience ( www.interscience.wiley.com ) DOI 10.1002/tcr.201000001     

Synthesis of amphiphilic copolymer brushes possessing alternating poly(methyl methacrylate) and poly(N‐isopropylacrylamide) grafts via a combination of ATRP and click chemistry

We report on the synthesis of well‐defined amphiphilic copolymer brushes possessing alternating poly(methyl methacrylate) and poly(N‐isopropylacrylamide) grafts, poly(PMMA‐alt‐PNIPAM), via a combination of atom transfer radical polymerization (ATRP) and click reaction (Scheme 1 ). Firstly, the alternating copolymerization of N‐[2‐(2‐bromoisobutyryloxy)ethyl]maleimide (BIBEMI) with 4‐vinylbenzyl azide (VBA) affords poly(BIBEMI‐alt‐VBA). Bearing bromine and azide moieties arranged in an alternating manner, multifunctional poly(BIBEMI‐alt‐VBA) is capable of initiating ATRP and participating in click reaction. The subsequent ATRP of methyl methacrylate (MMA) using poly(BIBEMI‐alt‐VBA) as the macroinitiator leads to poly(PMMA‐alt‐VBA) copolymer brush. Finally, amphiphilic poly(PMMA‐alt‐PNIPAM) copolymer brush bearing alternating PMMA and PNIPAM grafts is synthesized via the click reaction of poly(PMMA‐alt‐VBA) with an excess of alkynyl‐terminated PNIPAM (alkynyl‐PNIPAM). The click coupling efficiency of PNIPAM grafts is determined to be ～80%. Differential scanning calorimetry (DSC) analysis of poly(PMMA‐alt‐PNIPAM) reveals two glass transition temperatures (T_g). In aqueous solution, poly(PMMA‐alt‐PNIPAM) supramolecularly self‐assembles into spherical micelles consisting of PMMA cores and thermoresponsive PNIPAM coronas, which were characterized via a combination of temperature‐dependent optical transmittance, micro‐differential scanning calorimetry (micro‐DSC), dynamic and static laser light scattering (LLS), and transmission electron microscopy (TEM). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2608–2619, 2009     

Motion‐Based,High‐Yielding,and Fast Separation of Different Charged Organics in Water

We report a self‐propelled Janus silica micromotor as a motion‐based analytical method for achieving fast target separation of polyelectrolyte microcapsules, enriching different charged organics with low molecular weights in water. The self‐propelled Janus silica micromotor catalytically decomposes a hydrogen peroxide fuel and moves along the direction of the catalyst face at a speed of 126.3 μm s^?1. Biotin‐functionalized Janus micromotors can specifically capture and rapidly transport streptavidin‐modified polyelectrolyte multilayer capsules, which could effectively enrich and separate different charged organics in water. The interior of the polyelectrolyte multilayer microcapsules were filled with a strong charged polyelectrolyte, and thus a Donnan equilibrium is favorable between the inner solution within the capsules and the bulk solution to entrap oppositely charged organics in water. The integration of these self‐propelled Janus silica micromotors and polyelectrolyte multilayer capsules into a lab‐on‐chip device that enables the separation and analysis of charged organics could be attractive for a diverse range of applications.     

Thermoresponsive hydrogel of poly(glycidyl methacrylate‐co‐N‐isopropylacrylamide) as a nanoreactor of gold nanoparticles

The synthesis of a thermoresponsive hydrogel of poly(glycidyl methacrylate‐co‐N‐isopropylacrylamide) (PGMA‐co‐PNIPAM) and its application as a nanoreactor of gold nanoparticles are studied. The thermoresponsive copolymer of PGMA‐co‐PNIPAM is first synthesized by the copolymerization of glycidyl methacrylate and N‐isopropylacrylamide using 2,2′‐azobis(isobutyronitrile) as an initiator in tetrahydrofuran at 70 °C and then crosslinked with diethylenetriamine to form a thermoresponsive hydrogel. The lower critical solution temperature (LCST) of the thermoresponsive hydrogel is about 50 °C. The hydrogel exists as 280‐nm spheres below the LCST. The diameter of the spherical hydrogel gradually decreases to a minimum constant of 113 nm when the temperature increases to 75 °C. The hydrogel can act as a nanoreactor of gold nanoparticles because of the coordination of nitrogen atoms of the crosslinker with gold ions, on which a hydrogel/gold nanocomposite is synthesized. The LCST of the resultant hydrogel/gold nanocomposite is similar to that of the hydrogel. The size of the resultant gold nanoparticles is about 15 nm. The hydrogel/gold nanocomposite can act as a smart and recyclable catalyst. At a temperature below the LCST, the thermoresponsive nanocomposite is a homogeneous and efficient catalyst, whereas at a temperature above the LCST, it becomes a heterogeneous one, and its catalytic activity greatly decreases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2812–2819, 2007     

Iridium‐Catalyst‐Based Autonomous Bubble‐Propelled Graphene Micromotors with Ultralow Catalyst Loading

A novel concept of an iridium‐based bubble‐propelled Janus‐particle‐type graphene micromotor with very high surface area and with very low catalyst loading is described. The low loading of Ir catalyst (0.54 at %) allows for fast motion of graphene microparticles with high surface area of 316.2 m² g^?1. The micromotor was prepared with a simple and scalable method by thermal exfoliation of iridium‐doped graphite oxide precursor composite in hydrogen atmosphere. Oxygen bubbles generated from the decomposition of hydrogen peroxide at the iridium catalytic sites provide robust propulsion thrust for the graphene micromotor. The high surface area and low iridium catalyst loading of the bubble‐propelled graphene motors offer great possibilities for dramatically enhanced cargo delivery.     

Programmable Polymer‐Based Supramolecular Temperature Sensor with a Memory Function

A new class of polymeric thermometers with a memory function is reported that is based on the supramolecular host–guest interactions of poly(N‐isopropylacrylamide) (PNIPAM) with side‐chain naphthalene guest moieties and the tetracationic macrocycle cyclobis(paraquat‐p‐phenylene) (CBPQT⁴⁺) as the host. This supramolecular thermometer exhibits a memory function for the thermal history of the solution, which arises from the large hysteresis of the thermoresponsive LCST phase transition (LCST=lower critical solution temperature). This hysteresis is based on the formation of a metastable soluble state that consists of the PNIPAM–CBPQT⁴⁺ host–guest complex. When heated above the transition temperature, the polymer collapses, and the host–guest interactions are disrupted, making the polymer more hydrophobic and less soluble in water. Aside from providing fundamental insights into the kinetic control of supramolecular assemblies, the developed thermometer with a memory function might find use in applications spanning the physical and biological sciences.     

Enhanced Wettability Changes by Synergistic Effect of Micro/Nanoimprinted Substrates and Grafted Thermoresponsive Polymer Brushes

Thermoresponsive polymer brushes are grafted on micro/nanostructured polymer substrates as new intelligent interfaces that synergistically enhance wettability changes in response to external temperature stimuli. Thermoplastic poly(styrene‐co‐4‐vinylbenzyl chloride) [P(St‐co‐VBC)] is synthesized using radical polymerization and spin‐coated on a glass substrate. Micro/nanopillar and hole patterns are imprinted on the P(St‐co‐VBC) layer using thermal nanoimprint lithography. Poly(N‐isopropylacrylamide) (PIPAAm) brushes are grafted on the micro/nanostructured P(St‐co‐VBC) layer through surface‐initiated atom‐transfer radical polymerization using 4‐vinylbenzyl chloride as the initiator. The imprinted micro/nanostructures and grafted PIPAAm brush chain lengths affect the surface wettability. Combinations of nanopillars or nanoholes (diameter 500 nm) and longer PIPAAm brushes enhance hydrophobic/hydrophilic changes in response to temperature changes, compared with the flat substrate. The thermoresponsive hydrophobic/hydrophilic transition is synergistically enhanced by the nanostructured surface changing from Cassie–Baxter to Wenzel states. This PIPAAm‐brush‐modified micro/nanostructured P(St‐co‐VBC) is a new intelligent interface that effectively changes wettability in response to external temperature changes.

     

Syntheses and self‐assembly of poly(benzyl ether)‐b‐poly(N‐isopropylacrylamide) dendritic–linear diblock copolymers

This article describes the syntheses and solution behavior of model amphiphilic dendritic–linear diblock copolymers that self‐assemble in aqueous solutions into micelles with thermoresponsive shells. The investigated materials are constructed of poly(benzyl ether) monodendrons of the second generation ([G‐2]) or third generation ([G‐3]) and linear poly(N‐isopropylacrylamide) (PNIPAM). [G‐2]‐PNIPAM and [G‐3]‐PNIPAM dendritic–linear diblock copolymers have been prepared by reversible addition–fragmentation transfer (RAFT) polymerizations of N‐isopropylacrylamide with a [G‐2]‐ or [G‐3]‐based RAFT agent, respectively. The critical micelle concentration (cmc) of [G‐3]‐PNIPAM₂₂₀, determined by surface tensiometry, is 6.3 × 10^?6 g/mL, whereas [G‐2]‐PNIPAM₂₃₅ has a cmc of 1.0 × 10^?5 g/mL. Transmission electron microscopy results indicate the presence of spherical micelles in aqueous solutions. The thermoresponsive conformational changes of PNIPAM chains located at the shell of the dendritic–linear diblock copolymer micelles have been thoroughly investigated with a combination of dynamic and static laser light scattering and excimer fluorescence. The thermoresponsive collapse of the PNIPAM shell is a two‐stage process; the first one occurs gradually in the temperature range of 20–29 °C, which is much lower than the lower critical solution temperature of linear PNIPAM homopolymer, followed by the second process, in which the main collapse of PNIPAM chains takes place in the narrow temperature range of 29–31 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1357–1371, 2006     

Controlled aggregation behavior of thermoresponsive polymeric micelles by introducing hydrophilic segments as corona components

Poly[N‐isopropylacrylamide‐co‐N‐(3‐methoxypropyl)acrylamide]‐b‐poly(D,L‐lactide) (P(IPAAm‐co‐MPAAm)‐b‐PLA) as a thermoresponsive block copolymer and PMPAAm‐b‐PLA as a nonthermoresponsive block copolymer were co‐assembled into thermoresponsive polymeric micelles in water. In addition, PMPAAm‐b‐P(IPAAm‐co‐MPAAm)‐b‐PLA triblock copolymer was assembled to form thermoresponsive micelles with a hydrophilic layer on the outermost surface of the thermoresponsive corona. Using both micelles, we investigated the effects of introducing hydrophilic polymer segments on micellar aggregation behavior at temperatures above the lower critical solution temperature (LCST) of the thermoresponsive micelles. Despite the external hydrophilic PMPAAm layer on PMPAAm‐b‐P(IPAAm‐co‐MPAAm)‐b‐PLA micelles, aggregation following dehydration of the thermoresponsive segments was not significantly suppressed at temperatures above the LCST due to the instability of the core‐corona state. In contrast, intermicellar aggregation was successfully controlled by blending P(IPAAm‐co‐MPAAm) and PMPAAm in the thermoresponsive corona region, even above the LCST. In particular, PMPAAm chains longer than the P(IPAAm‐co‐MPAAm) chains could regulate the hydrodynamic diameter of micellar aggregates at temperatures above the LCST. The micelles showed enhanced drug release rates in response to temperature changes above the LCST without precipitating from solution. These results indicated that a side‐by‐side structure of hydrophilic/thermoresponsive chains in the corona region could effectively control the micellar aggregation state after a thermal phase transition. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1695–1704