Synthesis and characterization of soluble polyimides based on a new fluorinated diamine: 4-Phenyl-2,6-bis[3-(4′-amino-2′-trifluoromethyl-phenoxy) phenyl] pyridine

A new kind of pyridine-containing aromatic diamine monomer, 4-phenyl-2,6-bis[3-(4′-amino-2′-trifluoromethyl-phenoxy) phenyl] pyridine (m-PAFP), was successfully synthesized by a modified Chichibabin reaction of 3-(4′-nitro-2′-trifluoro-methyl-phenoxy)-acetophenone with benzaldehyde, followed by a catalytic reduction. A series of fluorinated pyridine-bridged aromatic poly(ether-imide)s were prepared from the resulting diamine monomer with various aromatic dianhydrides via a conventional two-step thermal or chemical imidization method. The inherent viscosities values of these polyimides were in the range of 0.56-1.02 dL/g, and they could be cast and thermally converted into transparent, flexible, and tough polyimide films. The polyimides displayed higher solubility in polar solvents such as NMP, DMSO and m-cresol. The polyimides had good thermal stability, with the glass transition temperatures (T_g) of 187-211 °C, the temperatures at 5% weight loss of 511-532 °C, and the residue at 800 °C in air was higher than 50%. These films also had dielectric constants of 2.64-2.74 at 10 MHz and low water uptake 0.53-0.66%. Wide-angle X-ray diffraction measurements revealed that these polyimides were predominantly amorphous. Moreover, the polymer films of these novel polyimides showed outstanding mechanical properties with the tensile strengths of 90.1-96.6 MPa, elongations at breakage of 8.9-10.7% and tensile modulus of 1.65-1.98 GPa.     

Formation of ordered macroporous films from fluorinated polyimide by water droplets templating

Preparation of honeycomb-patterned films from one of soluble fluorinated polyimides in a humid atmosphere was reported in this paper. This polyimide was synthesized from 2,2′-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA) and 2,2-bis[4-(4-aminophenoxy)phenyl]hexafluoropropane (BDAF) by two-steps method, which has excellent solubility both in strong bipolar solvents or in common low boiling-point solvents. The glass transition temperature of 6FDA-BDAF polyimide was determined by DSC and as 238 °C. Thermogravimetric analysis indicated that soluble fluoro-polyimide has good thermal stability with maximum thermal decomposition temperature of 545 °C in nitrogen atmosphere. The honeycomb-patterned films were obtained by casting a drop of polymer solution on a solid substrate in a humid atmosphere. Some influence factors, such as the solution concentration, the type of the solvent and the humidity, were also tested.     

Synthesis and characterization of novel fluorinated polyimides derived from 1,1′-bis(4-aminophenyl)-1-(3-trifluoromethylphenyl)-2,2,2-trifluoroethane and aromatic dianhydrides

A novel fluorinated aromatic diamine 1,1′-bis(4-aminophenyl)-1-(3-trifluoromethylphenyl)-2,2,2-trifluoroethane (6FDAM) was synthesized in a simple procedure, which was then employed to prepare a series of fluorinated polyimides with commercial aromatic dianhydrides, such as pyromellitic dianhydride (PMDA), 2,2-bis(3,4-dicarboxyphenyl)hexafluoropropane (6FDA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and 4,4′-oxydiphthalic anhydride (ODPA). The polyimides exhibited good solubility in strong dipolar solvents such as NMP, DMAc, DMF and m-cresol as well as some of low boiling point organic solvents of THF and CHCl₃, etc. Experimental results indicated the polyimides possessed low moisture adsorptions of 0.42-0.95%, low dielectric constant of 2.71-2.95 at 1 MHz, high dielectric strength of 92.0-122.6 kV/mm and good optical transparency with cutoff wavelengths of UV-vis at 330-375 nm. The polyimides also exhibited good mechanical properties as well as excellent thermal and thermo-oxidative stability. The fluorinated polyimides possessed better solubility, lower dielectric constant and water adsorption as well as higher optical transparency than the representative non-fluorinated polyimide derived from PMDA and 4,4′-oxydianiline (ODA).     

Synthesis and properties of novel fluorinated epoxy resins based on 1,1-bis(4-glycidylesterphenyl)-1-(3′-trifluoromethylphenyl)-2,2,2-trifluoroethane

A novel fluorinated epoxy resin, 1,1-bis(4-glycidylesterphenyl)-1-(3′-trifluoromethylphenyl)-2,2,2-trifluoroethane (BGTF), was synthesized through a four-step procedure, which was then cured with hexahydro-4-methylphthalic anhydride (HMPA) and 4,4′-diaminodiphenyl-methane (DDM). As comparison, a commercial available epoxy resin, bisphenol A diglycidyl ether (BADGE), cured with the same curing agents was also investigated. We found that the BGTF gave the exothermic starting temperature lower than BADGE no mater what kind of curing agents applied, implying the reactivity of the former is higher than the latter. The fully cured fluorinated BGTF epoxy resins have good thermal stability with glass transition temperature of 170-175 °C and thermal decomposition temperature at 5% weight loss of 370-382 °C in nitrogen. The fluorinated BGTF epoxy resins also showed the mechanical properties as good as the commercial BADGE epoxy resins. The cured BGTF epoxy resins exhibited improved dielectric properties as compared with the BADGE epoxy resins with the dielectric constants and the dissipation factors lower than 3.3 and dissipation 2.8 × 10⁻³, respectively, which is related to the low polarizability of the C-F bond and the large free volume of CF₃ groups in the polymer. The BGTF epoxy resins also gave low water absorption because of the existence of hydrophobic fluorine atom.     

Synthesis and properties of new pyridine-bridged poly(ether-imide)s based on 4-(4-trifluoromethylphenyl)-2,6-bis[4-(4-aminophenoxy)phenyl]pyridine

A novel pyridine-containing aromatic diamine monomer, 4-(4-trifluoromethylphenyl)-2,6-bis[4-(4-aminophenoxy)phenyl]pyridine (FAPP), was synthesized via the modified Chichibabin pyridine synthesis of 4-(4-nitrophenoxy)-acetophenone with 4-trifluoromethyl-benzaldehyde, followed by a catalytic reduction. A series of fluorinated pyridine-bridged aromatic poly(ether-imide)s were prepared from the resulting diamine monomer with various aromatic dianhydrides via a conventional two-step process. The resulting polyimides exhibited good solubility in aprotic amide solvents and m-cresol, such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and m-cresol, etc., which possessed the inherent viscosities of 0.76-0.91 dL/g. Strong and flexible poly(ether-imide) films were obtained, which showed excellent thermal properties with the glass transition temperatures of 268-353 °C, the temperature at 5% weight loss of 547-595 °C, and the residue at 700 °C of 65-74% in nitrogen, good mechanical properties with the tensile strengths of 87.6-104.2 MPa and elongations at breakage of 8.9-12.6%, and good optical transparency with the cut-off wavelengths of 357-380 nm, as well as low dielectric constants in the range of 2.49-3.04 at 1 MHz and low water uptake 0.43-0.69%. Furthermore, the resulted polyimides derived from FAPP were compared with non-fluorinated analogous polyimides and fluorinated analogous polyimides with trifluoromethyl groups in different positions, and the effects of substituents were also investigated and discussed.     

Synthesis and characterization of fluorinated polyimides derived from novel unsymmetrical diamines

Two kinds of aromatic, unsymmetrical diamines with ether-ketone group, 3-amino-4′-(4-amino-2-trifluoromethylphenoxy)-benzophenone and 4-amino-4′-(4-amino-2-trifluoromethylphenoxy)-benzophenone, were successfully synthesized with two different synthetic routes. Then, they were polymerized with 4,4′-oxydiphthalic anhydride, 3,3′,4,4′-benzophenone tetracarboxylic dianhydride, and 2,2′-bis(3,4-dicarboxyphenyl)-hexafluoropropane dianhydride to form a series of fluorinated polyimides via a conventional two-step thermal or chemical imidization method. The resulting polyimides were characterized by measuring their solubility, viscosity, mechanical properties, IR-FT, and thermal analysis. The results showed that the polyimides had inherent viscosities of 0.48-0.68 dl/g and were easily dissolved in bipolarity solvents and common, low-boiling point solvents. Meanwhile, the resulting strong and flexible polyimide films exhibited excellent thermal stability, e.g., decomposition temperatures (at 10% weight loss) are above 575 °C and glass-transition temperatures in the range of 218-242 °C. The polymer films also showed outstanding mechanical properties, such as tensile strengths of 86.5-132.8 MPa, elongations at break of 8-14%, and initial moduli of 1.32-1.97 GPa. These outstanding combined features ensure that the polymers are desirable candidate materials for advanced applications.     

Synthesis and characterization of soluble polyimides derived from a novel unsymmetrical diamine monomer: 1,4-(2′,4″-diaminodiphenoxy)benzene

A new aromatic unsymmetrical diamine monomer, 1,4-(2′,4″-diaminodiphenoxy)benzene (OAPB), was successfully synthesized in three steps using hydroquinone as starting material and polymerized with various aromatic tetracarboxylic acid dianhydrides, including 4,4′-oxydiphthalic anhydride (ODPA), 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BTDA), 2,2′-bis(3,4-dicarboxyphenyl)-hexafluoropropane dianhydride (6FDA) and pyromellitic dianhydride (PMDA) via the conventional two-step thermal or chemical imidization method to produce a series of the unsymmetrical aromatic polyimides. The polyimides were characterized by solubility tests, viscosity measurements, IR, ¹H NMR, and ¹³C NMR spectroscopy, X-ray diffraction studies, and thermogravimetric analysis. The polyimides obtained had inherent viscosities ranged of 0.38-0.58 dL/g, and were easily dissolved in common organic solvents. The resulting strong and flexible PI films exhibited excellent thermal stability with the decomposition temperature (at 5% weight loss) of above 505 °C and the glass transition temperature in the range of 230-299 °C. Moreover, the polymer films showed outstanding mechanical properties with the tensile strengths of 41.4-108.5 MPa, elongation at breaks of 5-9% and initial moduli of 1.15-1.68 GPa.     

Synthesis and characterization of novel fluorinated polyimides derived from 1,3-bis(4-amino-2-trifluoromethylphenoxy)naphthalene and aromatic dianhydrides

A new structurally asymmetric diamine monomer containing flexible ether linkages and bulky trifluoromethyl substituents, namely 1,3-bis(4-amino-2-trifluoromethylphenoxy)naphthalene, was prepared from 1,3-dihydroxynaphthalene and 2-chloro-5-nitrobenzotrifluoride. New series of fluorinated polyimides were synthesized from the diamine with six commercially available aromatic tetracarboxylic dianhydrides using a conventional two-stage process with thermal or chemical imidization. The resulting polyimides were highly soluble in a variety of organic solvents and could afford transparent and tough films via solution casting. These polyimides exhibited moderately high glass-transition temperatures (by DSC) of 236-268 °C and softening temperatures (by thermomechanical analysis) of 231-250 °C, and they did not show significant decomposition before 500 °C under either nitrogen or air atmosphere. Also, they revealed low moisture absorptions (0.32-0.78%), low dielectric constants (2.81-3.24 at 10 kHz), and high optical transparency (ultraviolet-visible absorption cutoff wavelengths of 377-426 nm).     

Meltable phenylethynyl-capped oligoimide resins derived from 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene and 3,4′-oxydianiline

A series of meltable oligoimide resins with controlled molecular weights by reactive phenylethynyl endcapping groups have been prepared by the thermal polycondensation of 3,3′,4,4′-biphenyltetracarboxylic dianhydride (s-BPDA) with the aromatic diamine mixtures consisting of different mole ratios of 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene (1,4,4-6FAPB) and 3,4′-oxydianiline (3,4′-ODA) in the presence of 4-phenylethynylphthalic anhydride (PEPA) as molecular weight-controlling and reactive endcapping reagent. Experimental results indicated that the molecular weight-controlled oligoimide resins were mixtures containing a series of biphenylethynyl-endcapped oligoimides with different chemical structures and different molecular weights. The typical oligoimide resins could be melted at temperatures of 300 °C to yield stable molten fluid with melt viscosity of 13.4 Pa s, which was suitable for melt processing. The molten oligoimide resins could be further polymer chain extended and crosslinked by thermal curing of the reactive phenylethynyl groups to give strong and tough thermosetted polyimides. Thus, the oligoimide resin with calculated molecular weight of 2500 exhibited not only good meltability with low melt viscosity, but also high melt stability and fluidability at temperatures of <300 °C. After thermal curing, the obtained thermosetted polyimide showed high glass transition temperature (>316 °C, DMA), excellent thermal stability with initial thermal decomposition temperature of 588 °C and good mechanical properties with flexural strength of 159.1 MPa, flexural moduli of 3.3 GPa, tensile strength of 94.7 MPa and elongation at breakage of 9.0%.     

Phenylethynyl terminated oligoimides derived from 3,3′,4,4′-diphenylsulfonetetracarboxylic dianhydride and their adhesive properties

A series of phenylethynyl terminated oligoimides based on 3,3′,4,4′-diphenylsulfonetetracarboxylic dianhydride (DSDA), m-phenylene diamine (m-PDA) or/and 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene (6FAPB) with calculated molecular weight of 5000 g mol⁻¹ were synthesized. The effect of molecular structure on solubility and melt viscosity of oligoimides as well as the thermal properties of cured polyimide resins was investigated. Experimental results indicated that the oligoimides have good solubility in strong polar solvents to afford homogeneous solutions with the solid content as high as 50 wt%. The oligoimides exhibited better solubility and lower minimum melt viscosity at relatively lower temperature with the incorporation of flexible 6FAPB. These oligoimides could be thermally cured at 320-380 °C to give thermosetted resins. The cured resins have good thermal stability with the glass transition temperatures of 278-329 °C and the onset decomposition temperatures higher than 500 °C. Adhesive properties of polyimides adhered to stainless steel at various conditions were evaluated by lap shear strength test. It was found that the LSS at room temperature increased with the molar ratio of 6FAPB increasing. The polyimides with combination of rigid and flexible structures exhibited good adhesive properties. With the increasing of curing temperature, the lap shear strength of polyimides at elevated temperature maintained at a high level due to the formation of strong bond.     

Novel soluble fluorinated aromatic polyamides derived from 2-(4-trifluoromethylphenoxy)terephthaloyl chloride with various aromatic diamines

A series of novel fluorinated aromatic polyamides derived from a new monomer, 2-(4-trifluoromethylphenoxy)terephthaloyl chloride (TFTPC), with various aromatic diamines were synthesized and characterized. The polyamides were obtained in high yields and moderately high inherent viscosities ranging from 1.07 to 1.16 dL/g. All the polyamides were amorphous and readily soluble in many organic solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N′-dimethylacetamide (DMAc), N,N′-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO), and could afford flexible and tough films via solution casting. The cast films exhibited good mechanical properties with tensile strengths of 82.8-107.3 MPa, elongation at break of 4.1-7.2%, and tensile modulus of 2.26-3.95 GPa. These polyamide films also exhibited good thermal stability with the glass transition temperature of 222-294 °C, the temperature at 5% weight loss of 442-472 °C in nitrogen. They exhibited low dielectric constants ranging from 3.25 to 3.39 (1 MHz), low moisture absorption in the range of 1.32-2.45%, high transparency with an ultraviolet-visible absorption cut-off wavelength in the 330-371 nm range, and excellent electrical properties.     

Synthesis and properties of organosoluble polyimides based on novel perfluorinated monomer hexafluoro-2,4-toluenediamine

New highly fluorinated aromatic polyimides based on hexafluoro-2,4-toluenediamine and commercially available dianhydrides (6FDA and ODPA) were synthesized by one-pot high temperature polycondensation in benzoic acid melt. Owing to the CF₃ group and fluorine atoms in the meta-linked phenylenediamine fragment, these polyimides combine good solubility in organic solvents including such a low boiling point solvent as chloroform with high glass transition temperatures (330-345 °C), thermal and thermooxidative stability (T₅ is >500 °C). The highly fluorinated polyimide films (hydrogen content is ≤1%) exhibit good dielectric properties and low water absorption as well as excellent optical transparency in the UV-vis region (cut-off wavelength is 311 nm for 6FDA-based and 357 nm for ODPA-based polyimides), which is very important for optoelectronic materials.     

Synthesis and characterization of polyimides based on novel isomeric perfluorinated naphthylenediamines

Novel highly fluorinated polyimides containing hexafluoronaphthylene fragment in the main chain were prepared by the two-stage polymerization of 2,7- and 2,6-diaminohexafluoronaphthalenes with 4,4′-oxydiphthalic anhydride: polycondensation in a solution at 80 °C followed by high-temperature solid-state chain extension. The influence of hexafluoronaphthylene fragment isomerism on the key polyimide features - molecular weight, thermal stability, solubility, optical properties - was characterized. Polyimides based on 2,7-diaminohexafluoronaphthalene or easily accessible mixture of isomeric diamines formed the flexible, transparent, and thermostable films.     

Adhesive and dielectric properties of novel polyimides with bis(3,3′-aminophenyl)-2,3,5,6-tetrafluoro-4-trifluoromethyl phenyl phosphine oxide (mDA7FPPO)

Polyimides with a low dielectric constant and excellent adhesion were prepared from a diamine containing phosphine oxide and fluorine groups, bis(3,3′-aminophenyl-2,3,5,6-tetrafluoro-4-trifluoromethyl phenyl phosphine oxide (mDA7FPPO), and rigid-rod type dianhydride containing fluorine groups, such as 3,6-di(3′,5′-bis(trifluoromethyl)-phenyl)pyromellitic dianhydride (12FPMDA). The polyimides were synthesized via the known two-step process, preparation of poly(amic-acid) followed by solution imidization, and characterized by FT-IR, NMR, DSC, TGA and TMA. In addition, their solubility, intrinsic viscosity, dielectric constant and adhesive property were also evaluated. For comparison, 3,6-di(4′-trifluoromethylphenyl) pyromellitic dianhydride (6FPMDA) and 3,6-diphenylpyromellitic dianhydride (DPPMDA) were also utilized. The prepared polyimides exhibited high T_g (276-314 °C), excellent thermal stability (>500 °C in air), good adhesive property (104.7-126.3 g/mm), good solubility, and very low dielectric constant (2.34-2.89).     

Synthesis and characterization of electrochromic poly(amide-imide)s based on the diimide-diacid from 4,4′-diamino-4″-methoxytriphenylamine and trimellitic anhydride

A dicarboxylic acid bearing two preformed imide rings, namely 4,4′-bis(trimellitimido)-4″-methoxytriphenylamine (3), was prepared by the condensation of 4,4′-diamino-4″-methoxytriphenylamine (2) and two molar equivalents of trimellitic anhydride (TMA). A new family of aromatic poly(amide-imide)s (PAIs) containing the electroactive triphenylamine (TPA) unit were prepared by the triphenyl phosphite activated polycondensation of the diimide-diacid 3 with various aromatic diamines. All the polymers were readily soluble in many organic solvents and could be solution-cast into tough and flexible polymer films. They displayed high glass-transition temperatures (269-313 °C) and good thermal stability, with 10% weight-loss temperatures in excess of 521 °C in nitrogen and char yields at 800 °C in nitrogen higher than 68%. Cyclic voltammograms of the PAI films cast onto an indium-tin oxide (ITO)-coated glass substrate exhibited one reversible oxidation redox couple at 0.91-0.93 V vs. Ag/AgCl in acetonitrile solution. The polymer films revealed a good electrochemical and electrochromic stability, with a color change from colorless neutral form to blue oxidized form at applied potentials ranging from 0.0 to 1.2 V. The PAIs containing the TPA unit in both imide and amide segments showed multicolor electrochromism: pale yellow in the neutral state, green in the semi-oxidized state, and deep blue in the fully oxidized state.     

Synthesis and properties of novel organosoluble polyimides derived from bis[3-(4-amino-2-trifluoromethylphenoxy) phenyl] ether

A new aromatic ether diamine, bis[3-(4-amino-2-trifluoromethylphenoxy) phenyl] ether, was successfully synthesized via nucleophilic substitution reaction of 3,3′-oxydiphenol and 2-chloro-5-nitrotrifluoromethylbenzene, followed by a catalytic reduction. A series of new polyimides were synthesized from the diamine with various commercially available aromatic dianhydrides via a conventional two-stage process, i.e. ring-opening polyaddition forming the poly(amic acid)s and further thermal or chemical imidization forming polyimides. The resulting polyimides exhibited good solubility in polar solvents, such as N,N-dimethylacetamide, N,N-dimethylformamide, N-methyl-2-pyrrolidinone and common solvents such as chloroform, tetrahydrofuran upon heating and possessed the inherent viscosities of 0.51-0.68 dL/g. The resulting strong and flexible films exhibited excellent thermal stability with the temperature at 10% weight loss is above 502 °C and the glass transition temperature in the range of 191-232 °C. The polyimides also were found to possess high optical transparency.     

Electroactive aromatic polyamides and polyimides with adamantylphenoxy-substituted triphenylamine units

A new triphenylamine-containing aromatic diamine monomer, 4-[4-(1-adamantyl)phenoxy]-4′,4″-diaminotriphenylamine, was synthesized from cesium fluoride-mediated N,N-diarylation of 4-(1-adamantyl)-4′-aminodiphenyl ether with 4-fluoronitrobenzene and subsequent reduction of the resultant dinitro compound. Novel electroactive aromatic polyamides and polyimides with adamantylphenoxy-substituted triphenylamine moieties were prepared from the newly synthesized diamine monomer with aromatic dicarboxylic acids and tetracarboxylic dianhydrides, respectively. All the resulting polymers were amorphous and most of them were readily soluble in polar solvents such as N-methyl-2-pyrrolidone (NMP) and N,N-dimethylacetamide (DMAc) and could be solution-cast into transparent and strong films with good mechanical properties. These polymers exhibited glass-transition temperatures between 254 and 310 °C, and they were fairly stable up to a temperature above 450 °C for the polyamides and above 500 °C for the polyimides. These polymers exhibited strong UV-vis absorption maxima at 293-346 nm in solution, and the photoluminescence spectra of polyamides showed maximum bands around 408-452 nm in the blue region. Cyclic voltammograms of the polyamide and polyimide films on an indium-tin oxide (ITO)-coated glass substrate exhibited one pair of reversible redox couples at half-wave oxidation potentials (E_1/2) around 0.83-0.86 V and 1.12-1.13 V, respectively, versus Ag/AgCl in an acetonitrile solution. All the polymer films revealed good electrochemical and electrochromic stability by repeatedly switching electrode voltages between 0.0 V and 1.1-1.4 V, with coloration change from the pale yellowish neutral state to the green or blue oxidized state.     

Novel polyfluorinated polyimides derived from α,α-bis(4-amino-3,5-difluorophenyl)phenylmethane and aromatic dianhydrides: Synthesis and characterization

A novel aromatic diamine containing bulky lateral phenyl unit and fluorine groups ortho-substituted to the amino groups in the structure, α,α-bis(4-amino-3,5-difluorophenyl)phenylmethane (4FMA) was synthesized and characterized. 4FMA was polymerized with four aromatic dianhydrides to afford a series of polyimides (PIs) via a one-step high-temperature polycondensation procedure. All the PIs were amorphous and showed good solubility not only in polar aprotic solvents, but in many common solvents, such as cyclopentanone and tetrahydrofuran. The soluble polymers formed flexible, tough and transparent films. The films had a tensile strength, elongation at break, and tensile modulus in the ranges 85-107 MPa, 4-7%, 1.7-2.8 GPa, respectively. The polyimides also exhibited high-T_g (292-338 °C), good thermal stability, good dielectric strength, low dielectric constants, and low water uptakes due to the introduction of the polyfluorinated substituents in the polymer backbone. As expected, the PI films showed good transparency in the UV-Vis light region with cutoff wavelength as low as 318 nm and transmittance higher than 60% at 450 nm. PI-4 derived from 4FMA and fluorinated dianhydride 6FDA exhibited low light-absorption in the near-infrared region, especially at the optocommunication wavelength of 1310 nm and 1550 nm. The remarkable combined properties indicate their potential applications in microelectronic and optoelectronic fabrications.     

Synthesis and characterization of new polyimides containing pendent pentadecyl chains

A new unsymmetrical aromatic diamine, viz., 4-pentadecylbenzene-1,3-diamine was synthesized through a series of reaction steps starting from 3-pentadecylphenol. 4-Pentadecylbenzene-1,3-diamine was employed to synthesize a series of new polyimides by one-step polycondensation in m-cresol with four commercially available aromatic dianhydrides, viz., 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), 4,4′-oxydiphthalic anhydride (ODPA) and 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6-FDA). Inherent viscosities of resulting polyimides were in the range 0.33-0.67 dL/g and number average molecular weights were in the range 14,700-52,200 (GPC, polystyrene standard). Polyimides containing pendent pentadecyl chains were soluble in organic solvents such as chloroform, m-cresol, N,N-dimethylacetamide (DMAc), 1-methyl-2-pyrrolidinone (NMP), pyridine and nitrobenzene. Strong and flexible films of polyimides could be cast from their chloroform solutions. Polyimides exhibited glass transition temperature in the range 158-206 °C. The temperature at 10% wt. loss (T₁₀), determined by TGA in nitrogen atmosphere, of polyimides was in the range 470-480 °C indicating good thermal stability.     

Synthesis and characterization of fluorinated liquid-crystalline elastomers containing chiral liquid-crystalline crosslinking units

Fluorinated chiral liquid-crystalline elastomers (LCEs) were graft copolymerized by a one-step hydrosilylation reaction with polymethylhydrogenosiloxane, a fluorinated LC monomer 4-(2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-pentadecafluorooctanoyloxy)phenyl 4-(undec-10-enoyloxy)benzoate (PPUB) and a chiral crosslinking LC monomer (3R,3aR,6S,6aR)-6-(undec-10-enoyloxy)hexahydrofuro[3,2-b]furan-3-yl 4′-(4-(allyloxy)benzoyloxy)biphenyl-4-carboxylate (UHAB). The chemical structure, liquid-crystalline behavior and polarization property were characterized by use of various experimental techniques. The effective crosslink density of the LCEs was characterized by swelling experiments. The thermal analysis results showed that the temperatures at which 5% weight loss occurred were greater than 250 °C for all the LCEs, and the residue weight nearby 600 °C increase with increasing chiral crosslinking components in the polymer systems. All the samples showed chiral smectic C mesophase when they were heated. The glass transition temperature and mesophase-isotropic phase transition temperature of fluorinated elastomers increased slightly with increase of chiral crosslinking mesogens in the polymer systems, but the enthalpy changes of mesophase-isotropic phase transition decreased slightly. In XRD curves, all the samples exhibited strong sharp reflections at small angles suggesting smectic layered packing arrangement. These fluorinated chiral LCEs showed 0.1–0.2 μC/cm² of spontaneous polarization with increasing chiral crosslinking component.