由聚苯胺粒子组成的电流变液的研究

由经碱处理的掺杂态聚苯胺（ＰＡｎ）制得高介电常数的半导体ＰＡｎ粒子，将其悬浮于电绝缘油可组成电流变液，讨论了电流变（ＥＲ）液的静态屈服应力（τ＿ｓ），电流密度等性能与ＰＡｎ的介电常数（ε＿ｐ），导电率（σ），体积分数和应用电场强度的关系。对导电率相同的ＰＡｎ粒子，用氨水处理的ＰＡｎ粒子ε＿ｐ较用ＮａＯＨ液处理的高，前者在σ足够低如σ≤１．０×１０￣（－７）／ｃｍ时，ＥＲ液的τ＿ｓ随偶极系数的平方（β￣２）的增大而呈现非线性增加；后者ＥＲ液的τ＿ｓ随β￣２的增大出现一最大值．结果表明：由聚苯胺粒子可组成高电流变活性的无水ＥＲ液．     

化学合成环取代聚苯胺的电化学行为

聚邻甲苯胺（ＰＯＴ）、聚２,５ 二甲氧苯胺（ＰＤＭＡｎ）和聚间氯代苯胺（ＰＣｌＡｎ）由化学法合成而得,用它们的二甲基甲酰胺溶液在铂上成膜以制得聚合物修饰电极．循环伏安实验表明：在１ｍｏｌ／ＬＨ２ＳＯ４中,ＰＯＴ的氧化还原分两步进行,呈现两对氧化还原峰,ＰＤＭＡｎ只在较负的电位区呈现两对氧化还原峰,而ＰＣｌＡｎ不呈氧化还原活性．不同电位下的交流阻抗特征与循环伏安图相对应．三种聚合物膜电极在０．５ｍｏｌ／ＬＫ３［Ｆｅ（ＣＮ）６］溶液中的伏安图也证明铁氰离子的还原速度依ＰＯＴ＞ＰＤＭＡｎ＞ＰＣｌＡｎ的顺序而下降．环取代基的影响用电子效应和几何效应进行解释．可溶性聚苯胺便于制作大面积器件,环取代基对调节聚苯胺的电化学性能具有重要作用,值得进一步研究．     

Electrochemical Behavior of Chemically Prepared Ring-Substituted Polyanilines

聚邻甲苯胺（ＰＯＴ）、聚２，５二甲氧苯胺（ＰＤＭＡｎ）和聚间氯代苯胺（ＰＣｌＡｎ）由化学法合成而得，用它们的二甲基甲酰胺溶液在铂上成膜以制得聚合物修饰电极．循环伏安实验表明：在１ｍｏｌ／ＬＨ２ＳＯ４中，ＰＯＴ的氧化还原分两步进行，呈现两对氧化还原峰，ＰＤＭＡｎ只在较负的电位区呈现两对氧化还原峰，而ＰＣｌＡｎ不呈氧化还原活性．不同电位下的交流阻抗特征与循环伏安图相对应．三种聚合物膜电极在０．５ｍｏｌ／ＬＫ３［Ｆｅ（ＣＮ）６］溶液中的伏安图也证明铁氰离子的还原速度依ＰＯＴ＞ＰＤＭＡｎ＞ＰＣｌＡｎ的顺序而下降．环取代基的影响用电子效应和几何效应进行解释．可溶性聚苯胺便于制作大面积器件，环取代基对调节聚苯胺的电化学性能具有重要作用，值得进一步研究．     

掺杂态聚苯胺的溶解性和可加工性

本文对改善掺杂态ＰＡｎ加工性的几种方法（如现场聚合、胶体分散和有机酸掺杂）作了扼要评述，指出导电ＰＡｎ正处于工业化应用前期。     

有效主量子数拓扑指数与分子总键能和晶格能的关系

作者定义ＡｊＢｋ分子的有效主量子数拓扑指数（Ｐ）为：Ｐ＝∑（ｎＡ·ｎＢ）－０．５。它与化合物的总键能（ΔＥ）、晶格能（Ｕ）呈现高度相关性,其直线回归方程为：ΔＥ＝－２８．４５１８＋１１１７．８９８Ｐ,Ｒ＝０．９３５４Ｕ＝１９６．６７０３＋１６６５．６２６６Ｐ,Ｒ＝０．９８８２用它预测ΔＥ、Ｕ,估算值与实验值基本吻合     

聚苯胺/苯乙烯-丁二烯-苯乙烯复合材料伸长过程中的导电性变化

以简化物理模型为基础，用实测电流与理论电流之比来研究导电橡胶伸长中电导率的变化，并建立相应测试方法．聚苯胺（ＰＡｎ）／苯乙烯 丁二烯 苯乙烯三嵌段共聚物的复合物用现场乳液聚合法制备．此复合物可熔融加工（ＭＰ）和溶液加工（ＳＰ）．ＳＳＰ样为ＳＰ样用间甲酚二次掺杂处理制得．对ＰＡｎ质量分数为１１０％的复合物进行电导率随伸长变化测试结果表明：ＭＰ样随伸长增加其电导率显著提高，在伸长率为４５０％时，其电导率是初始值（σ０）的１５６倍；ＳＰ样在伸长过程中电导率随伸长而增加，在伸长率为５００％时，其电导率是σ０的５２倍；而ＳＳＰ样在整个伸长过程中电导率变化较小，σ０＜σ＜２σ０．可从复合物的聚集态结构解释以上现象．ＳＳＰ样在导电组分的含量接近逾渗域值时电导率随伸长迅速下降．而当导电组分含量高于逾渗域值时电导率随伸长表现出小的变化并具规律性，此规律性可用σσ０＝１＋ｋａ＋ｂｋ２经验公式来表达（ａ，ｂ为与含量相关的常数）．此结果是由于ＳＳＰ样中导电组分在二次掺杂过程中分子链间存在弱相互作用而自行组成导电网络     

用共混和共聚法改性聚苯胺及其电流变液的研究

通过共混和表面接枝共聚两种方法改性聚苯胺，制备聚苯胺（ＰＡｎ）复合粒子并用它们组成活性较高的电流变（ＥＲ）液．研究了ＰＡｎ复合粒子的结构与ＥＲ液性能的关系．结果表明在ＰＡｎ粒子表面涂覆聚乙烯醇或接枝聚丙烯酰胺等与ＰＡｎ能形成氢键或有化学键连接的绝缘物质可以既提高其ＥＲ液的电诱导屈服应力又降低漏电流密度．     

聚苯胺／聚乙烯醇导电复合膜的制备及性质研究

用较简单的化学氧化现场吸附聚合法（ｉｎ－ｓｉｔｕｐｏｌｙｍｅｒｉｚａｔｉｏｎ）制得了聚苯胺（ＰＡｎ）／聚乙烯醇（ＰＶＡ）导电复合膜．该膜具有较好的导电性和机械性能；其电导率可达５．８ｓ／ｃｍ，拉伸强度达１３ＭＰａ，断裂伸长率为１１０％左右．本文讨论了制备的各种条件对复合膜导电性能及力学性能的影响、稳定性及电化学活性；并采用循环伏安曲线、扫描电镜（ＳＥＭ）、ＦＴＩＲ谱及元素分析对该复合膜的结构和性能进行了表征．     

聚苯胺水基胶体分散液及其复合物的研究 Ⅰ制备、表征及复合物的表观形貌、力学性能

以聚乙烯醇（ＰＶＡ）为稳定剂（ｓｔｅｒｉｃｓｔａｂｉｌｉｚｅｒ）利用分散聚合（ｄｉｓｐｅｒｓｉｏｎｐｏｌｙｍｅｒｉ ｚａｔｉｏｎ）的原理，成功地制备出了稳定的聚苯胺（ＰＡｎ）水基胶体分散液．聚苯胺颗粒的大小受聚合条件如稳定剂浓度、单体浓度、温度以及搅伴状态等的影响．ＰＶＡ通过物理作用吸附在ＰＡｎ颗粒的表面，起到阻止ＰＡｎ颗粒进一步团聚的作用．但这种作用力较弱．ＰＡｎ颗粒的原始尺寸大小约为２０ｎｍ．由此原始颗粒组成了尺寸在１００ｍｍ～２００ｍｍ左右的稳定颗粒     

聚苯胺溶液的凝胶化行为

通过流变学手段对聚苯胺溶液的凝胶化行为研究表明，在室温下，聚苯胺（ＰＡｎ）／Ｎ－甲基－２－吡咯烷酮（ＮＭＰ）溶液有一转折浓度Ｃｇ（０．０５ｇ／ｍＬ），浓度高于此值时，浴液凝胶化速度急剧增大，凝胶速度还与溶剂，ＰＡｎ分子量及溶液的温度有很大关系。溶液中不溶的ＰＡｎ的存在会加速凝胶化过程。ＰＡｎ／ＮＭＰ凝胶的假塑性和触变性明显地反映出ＰＡＶＮＭＰ溶液的凝胶化是溶剂参与的ＰＡｎ分子链间的物理交联过程。     

乳液聚合中聚苯胺膜形成的动力学研究

以(NH4)2S2O8(APS)为氧化剂,十二烷基苯磺酸(DBSA)同时为乳化剂和掺杂剂,采用乳液聚合方法制备聚苯胺膜(PANIfilm),用石英晶体微天平(QCM)实时监测聚苯胺膜的形成过程,并对其动力学过程进行研究.结果表明,聚苯胺成膜反应对APS是0.5级,对苯胺是1级,聚苯胺膜增长速率随温度的升高而增加,而聚苯胺膜的最终沉积量却减小,表观活化能Ea=41.15kJ/mol,与均相溶液聚合成膜法的结果相近;随着DBSA浓度的增加,聚苯胺膜增长速率减小,而最终的沉积量增大.     

Oligomer-immobilizing ability of an electrodeposited aramid resin film in the electrooxidation of aniline derivatives and the functions of the resulting films

An aramid resin, poly(p-phenylene terephthalamide) (PPTA), was electrodeposited on an indium-tin oxide electrode as a mechanically stable film from a dimethyl sulfoxide solution. Two aniline derivatives, o-phenylenediamine and o-aminophenol, were electrooxidized from H₂SO₄ aqueous solutions using the PPTA film-coated electrode. The PPTA film was permeable to the aniline derivatives, and the derivatives were electrooxidized on the electrode surface. When the derivatives were electrooxidized, the film immobilized the corresponding oligomer species as well as the polymers plain (o-phenylenediamine) (PoPD) and poly(o-aminophenol) (PoAP), and the deposited amount of the polymers was increased by the PPTA film. The immobilized amount of PoAP was greater than that of PoPD because of the 1,4-substituted structure of PoAP. In the PPTA film, both PoPD and PoAP were electronically stabilized, and they became durable against oxidative degradation.     

Effect of cationic monomer on properties of fluorinated acrylate latex

Cationic fluorinated acrylate latex was prepared via semi-continuous emulsion copolymerization of cationic monomer and other monomers.The resultant latex and its film were characterized with dynamic light scattering detector and contact anglc meter. Influences of amount of DMDAAC on the propcrtics of resultant latex and its film were investigated in detail.Results show that the particle size of the latex has the minimum value and the zeta potential of the latex is increased when the amount of DMDAAC is increased.In addition,the particle size of the latex is unimodal distribution when the amount of DMDAAC is not more than 2.5%. However,the particle size of the latex is bimodal distribution when the amount of DMDAAC is more than 2.5%.The contact angle is varied slightly with the increase of amount of DMDAAC when it is not more than 2.5%.Nevertheless,the contact angle is decreased with the increase of the amount of DMDAAC when it is more than 2.5%.     

Polyaniline film formation in hexadecyl trimethyl ammonium bromide admicelles on hydrous zirconia surface

Formation of a thin polyaniline film on hydrous zirconia (ZrO2) surface was carried out using adsorbed surfactant bilayers on ZrO2 as reaction sites. Aniline was adsolubilized in hexadecyltrimethylammonium bromide (HDTAB) admicelles formed on the surface of ZrO2 by adsorption. Subsequent polymerization of the adsolubilized aniline monomer showed effective conversion of aniline to polyaniline. The formation of the polyaniline coated ZrO2 has been confirmed by UV-visible spectroscopy, FT-IR spectroscopy, and conductivity measurements. Various parameters involved during the adsorption process were studied. Selection of pH 9.0 as the pH of all experimental feed solutions was governed by the knowledge of point of zero charge (PZC) of ZrO2. Effect of aniline concentration on HDTAB adsorption was studied and it was observed that increase in aniline concentration decreased the amount of HDTAB adsorbed on ZrO2. Addition of salt (0.05 M NaCl) in the feed solution increased HDTAB adsorption and drastically reduced the effect of aniline concentration on HDTAB adsorption.     

Preparation of hybrid film of polyaniline and organically pillared zirconium phosphate nanosheet by electrodeposition

α-Zirconium phosphate was chemically modified with 1,2-bis(dimethylchlorosilyl)ethane to graft organic chain, and then it was used as host material for inorganic nanosheet-polyaniline hybrid. The grafted α-zirconium phosphate was exfoliated in an acetonitrile solution with tetrabutylammonium salt and aniline. The electrodeposition in the presence of aniline was performed, and then it resulted in a formation of higher-order structure in which phosphate nanosheet was propped up by 1,2-bis(dimethylchlorosilyl)ethane with intrusion of polyaniline into the nanospace. The gravimetric capacitance of the α-zirconium phosphate without grafts and polyaniline hybrid film was around 194 F/g with the base on the amount of polyaniline mass. On the other hand, the α-zirconium phosphate nanosheet with grafts and polyaniline hybrid film provided larger capacitance of around 350 F/g in maximum. The nanospace formed by grafted phosphate nanosheet with 1,2-bis(dimethylchlorosilyl)ethane molecules gives increased amounts of polyaniline included and diffusion paths for ions.     

Properties and morphologies of UV‐cured epoxy acrylate blend films containing hyperbranched polyurethane acrylate/hyperbranched polyester

The properties and morphologies of UV‐cured epoxy acrylate (EB600) blend films containing hyperbranched polyurethane acrylate (HUA)/hyperbranched polyester (HPE) were investigated. A small amount of HUA added to EB600 improved both the tensile strength and elongation at break without damaging its storage modulus (E′). The highest tensile strength of 31.9 MPa and an elongation at break around two times that of cured pure EB600 were obtained for the EB600‐based film blended with 10% HUA. Its log E′ (MPa) value was measured to be 9.48, that is, about 98% of that of the cured EB600 film. The impact strength and critical stress intensity factor (K_1c) of the blends were investigated. A 10 wt % HUA content led to a K_1c value 1.75 times that of the neat EB600 resin, and the impact strength of the EB600/HPE blends increased from 0.84 to 0.95 kJ m^?1 with only 5 wt % HPE addition. The toughening effects of HUA and HPE on EB600 were demonstrated by scanning electron microscopy photographs of the fracture surfaces of films. Moreover, for the toughening mechanism of HPE to EB600, it was suggested that the HPE particles, as a second phase in the cured EB600 film, were deformed in a cold drawing, which was caused by the difference between the elastic moduli of HPE and EB600. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3159–3170, 2005     

表面活性剂对苯胺电聚合的影响

利用胶束在电极一有面的定向及增溶作用研究了表面活性剂对苯胺电聚合的影响，结果表明：在阴离子表面活性剂十二烷基硫酸钠（ＳＤＳ）胶束体系中，胶束介质能催化苯胺的电聚合反应，使其氧化电位负移，减少膜的降解，提高膜的稳定性，同时，也使得聚合速率增大，在０．１ｍｏｌ／Ｌ的ＳＤＳ的胶束溶液中，其聚合效率提高到不含ＳＤＳ的纯体系的２５倍，在含有１０＾－４ｍｏｌ／ＬＳＤＳ的硫酸溶液中，聚苯胺（ＰＡＮ）的成核生长为     

Electrodeposition and Characterization of Polyaniline Film

Polyaniline film was prepared by electrochemical method in an acidic solution of aniline. The micromorphology of the polyaniline film was transformed to three-dimensional network structure instead of little particles while the deposition time was extended. The peak wavelength of the photoluminescence spectrum was 491 nm. The luminous intensity increased with the extension of deposition time, and so did the electrochemical activity.     

Sodium Dodecyl Sulfate Doped Polyaniline for Enhancing the Electrochemical Sensitivity of Mercury Ions

Polyaniline (PANi) was electro‐synthesized on the surface of screen‐printed carbon electrodes in the presence of sodium dodecyl sulfate (SDS) as a dopant. The complex of aniline and SDS created a conductive (PANi‐SDS) film at lower aniline concentration. The PANi‐SDS film contained negative charge due to the anionic head of SDS. The PANi‐SDS modified electrode was integrated into a poly(dimethylsiloxane) microfluidic chip as an electrochemical sensor for mercury detection. The presence of SDS in the polyaniline film enhanced the possibility of mercury ions uptake, and therefore, increased the peak current of square wave anodic stripping in the mercury detection. The mercury sensor exhibited a dynamic range from 6 to 35 nM with detection limit of 2.4 nM.     

Emulsifier-free latex of fluorinated acrylate copolymer

Emulsifier-free latices of fluorinated acrylate copolymers were prepared by semicontinuous polymerization method, with perfluoroalkylethyl methacrylate (Zonyl TM) as a fluoromonomer. Ultrasonic at 40 kHz was adopted to help monomers disperse well in water. The relationships of polymerization conditions between the final conversion and polymerization stability were discussed in detail and the optimal polymerization condition was given. A fluorinated acrylate copolymer was finally obtained and its T_g was 54 °C. The average particle size of the latex was about 601 nm and the particle size distribution of the latex was narrow. The latex film exhibited a low surface free energy and good surface property. By using 6% Zonyl TM, the water contact angle of the film-air interface increased significantly and reached to 110.2°. Compared with the latex film of fluorine-free polyacrylate prepared under the similar polymerization condition, the fluorinated latex film had a better water-resistance and thermal stability.