磁场及反应条件对十二烷基苯磺酸掺杂聚苯胺聚合成膜速率的影响

在恒定磁场(0.6 T)条件下, 采用过硫酸铵(APS)为引发剂, 在乳液体系中合成了十二烷基苯磺酸(DBSA)掺杂的聚苯胺(PAn). 借助石英晶体微天平(QCM)实时监测苯胺(An)在金电极表面聚合成膜过程, 探讨了磁场、APS浓度、DBSA浓度及反应温度对DBSA掺杂聚苯胺聚合成膜速率的影响. 实验结果表明, PAn在金电极表面的成膜速率随磁场强度的增加而增大; 由反应物浓度与PAn成膜速率的关系, 得出相应的动力学反应级数; 由PAn膜的增长速率与温度的关系, 得到成膜过程的活化能为41.08 kJ/mol. 考察了PAn聚合过程的UV-Vis光谱, 并与QCM所得的结果进行了比较. 结果显示, 在相同时间内, 磁场环境下合成的PAn的吸收强度大于无磁环境下合成的PAn.     

聚苯胺在聚酰亚胺膜基体表面的原位沉积成膜机理

采用分散聚合方法,在聚酰亚胺(PI)膜基体表面原位成膜,制备聚苯胺-聚酰亚胺-聚苯胺(PANI-PI-PANI)导电复合膜.通过反应历程跟踪、扫描电镜(SEM)及静滴接触角-界面张力测量仪研究了PANI在PI基体表面原位成膜的过程及其驱动力.结果表明,PANI在PI基体表面的成膜过程有3个阶段:含苯胺的结构单元(包括An盐酸盐、An阳离子自由基及低聚物)在PI表面吸附成核阶段、膜快速增长阶段和增长完成阶段;PANI膜由PANI小颗粒逐渐堆积而成,直至覆盖整个PI膜表面;PANI成膜的主要驱动力来自亲水-疏水相互作用.     

PANI 在玻璃基体表面的生长成膜过程

采用分散聚合法,在玻璃基体表面原位生长聚苯胺制得高电导率(10-3S/cm)、微纳米级的聚苯胺薄膜.通过扫描电镜、原子力显微镜以及接触角分析研究聚苯胺在玻璃基体表面成膜的驱动力和过程.结果表明:成膜的驱动力是聚合过程中产生的活性中间体与基体间的强吸附力.活性中间体主要是苯胺的二聚体、三聚体等短链小分子,它们与基体问的作用为分子间力作用,属物理吸附.聚苯胺在玻璃基体表面成膜的过程符合吸附生长模式,膜的厚度存在饱和值.     

石英晶体微天平技术在苯胺乳液聚合动力学研究中的应用

采用石英晶体微天平(QCM)技术, 探讨了在有无磁场条件下, 用过硫酸铵(APS)作为引发剂时苯胺的乳液聚合动力学行为. 研究结果表明, 苯胺的乳液聚合反应速率对苯胺(An)是一级反应; 对APS和十二烷基苯磺酸(DBSA)均为0.5级反应. 磁场环境中苯胺的聚合速率比在无磁环境中的要快. 在有无磁场条件下, 反应的表观活化能分别为40.4和41.6 kJ/mol. 结果表明, QCM技术可以作为研究An聚合动力学的一种有效方法.     

苯胺在十二烷基苯磺酸/水体系中的乳液聚合过程研究

利用光学显微镜和扫描电镜,对以水为介质、十二烷基苯磺酸(DBSA)为乳化剂的苯胺乳液聚合过程进行监测,发现苯胺在水体系中与DBSA反应形成DBSA-苯胺盐的棒状聚集结构,讨论了DBSA、苯胺、氧化剂的配比及浓度对聚合过程中棒状聚集结构的长度和数量及生成聚苯胺的电导率的影响,提出苯胺在DBSA/水体系中的乳液聚合反应是在胶束表面进行的,而棒状聚集结构中的DBSA-苯胺盐单体经水相扩散到乳胶粒子中,形成颗粒状的聚苯胺.     

FeCl_3/APS复合氧化剂对乳液法合成聚苯胺动力学行为的影响

采用石英晶体微天平(QCM)技术,探讨了以三氯化铁(FeCl3)和过硫酸铵(APS)为复合氧化剂,十二烷基苯磺酸(DBSA)为乳化剂和掺杂剂时,苯胺(An)的乳液聚合动力学行为;并通过对产物的循环伏安分析,初步优化了聚合反应条件.结果表明,An的乳液聚合反应对复合氧化剂、An以及DBSA分别为1,0.5和0.5级.各种条件下的循环伏安(CV)图都显示出PAn的三对氧化还原特征峰.当FeCl3与APS物质的量比为2∶1;氧化剂总量与苯胺的物质的量比为3∶1;DBSA浓度为0.05mol/L时,CV测试的峰电流和电导率最大.     

二(乙酰丙酮根)合铜(Ⅱ)热分解动力学研究

金属有机化合物气相化学沉积(OMCTD)形成铜膜常用的母体化合物是铜(Ⅱ)的β-二酮类配合.本文首次采用CW二氧化碳激光研究二(乙酰丙酮根)合铜(Ⅱ)[Cu相似文献   

二(乙酰丙酮根)合铜(Ⅱ)热分解动力学研究

金属有机化合物气相化学沉积(OMCTD)形成铜膜常用的母体化合物是铜(Ⅱ)的β-二酮类配合.本文首次采用CW二氧化碳激光研究二(乙酰丙酮根)合铜(Ⅱ)[Cu相似文献   

苯胺分散聚合中稳定剂PVP-K90的稳定机理

通过分散聚合,在聚酰亚胺(PI)薄膜表面原位沉积聚苯胺(PANI)制备聚苯胺-聚酰亚胺-聚苯胺(PANI-PI-PANI)复合膜。考察了苯胺分散聚合中,不同空间稳定剂的稳定效果(不同分子量的大分子稳定剂PVP及小分子稳定剂CTAB、Tween-20),初步探讨了大分子稳定剂PVP-K90的稳定机理。实验表明,高分子量PVP-K90可稳定PANI良好成膜,且紫外和红外光谱分析证实PANI膜为掺杂态PANI,膜中不含有稳定剂PVP-K90。低分子量的PVP-K30和两亲性小分子稳定剂不能良好地稳定PANI成膜,稳定作用较差。PVP-K90的稳定作用不仅依据亲水-疏水相互作用和表面能的减少,还可能与高分子量PVP的长链分子结构及与水和苯胺的特殊相互作用有关,可用齐聚物沉淀成核机理解释。     

22Cr双相不锈钢钝化膜组成及其半导体性能研究

借助于Mott-Schottky方程分析了成膜电位、成膜时间、成膜温度以及氯离子等因素对22Cr双相不锈钢在碳酸氢钠/碳酸钠缓冲溶液中所成钝化膜半导体性能的影响, 同时借助于X射线光电子能谱(XPS)技术分析了所成钝化膜的组成. 结果表明: 22Cr双相不锈钢在碳酸氢钠/碳酸钠缓冲溶液中所成钝化膜呈n-p型半导体结构, 钝化膜内施主/受主密度随成膜电位增加、成膜时间延长、成膜温度降低、以及介质中氯离子浓度的降低而减小, 同时膜对基体保护作用随这些因素变化而增强. 钝化膜的XPS分析表明, 钝化膜呈现双层结构, 外层膜主要由三价铁的氧化物(Fe2O3)组成, 内层膜主要由三价铬氧化物(Cr2O3)以及少量二价铁氧化物(FeO)组成.     

The kinetics and spectral studies of the in situ polyaniline film formation

The chemical oxidation of aniline with ammonium persulfate (APS) in an aqueous acidic solution to form polyaniline (PANI) films has been studied using the quartz crystal microbalance (QCM) technique. The kinetics of the film formation was investigated. The reaction exhibited half-order with respect to APS and first-order to aniline. The effect of temperature on the growth rate of PANI films was studied. The activation energy is 39.79 kJ/mol. This is in agreement with the corresponding one determined for the chemical polymerization of PANI in the bulk. The UV-visible spectra of the PANI films grown onto a glass support immersed into the bulk solution were measured. The absorption of the PANI film with time was also studied and compared to the growth of the PANI film thickness using the QCM technique.     

Film thickness studies for the chemically synthesized conducting polyaniline

The chemical oxidation of aniline with ammonium persulphate (APS) in aqueous acidic medium to form polyaniline (PANI) films has been studied using the quartz crystal microbalance (QCM) technique. PANI films can also grow onto glass supports immersed in the reaction mixture during the polymerization. The optical absorption for these films was measured. Multilayer deposition of polymer films onto the gold electrode of QCM and onto the glass supports from consecutive repetitive treatments by the reaction mixture containing aniline and APS, were studied. The induction period, the yield and the growth rate of the polymer films during the multilayer deposition were discussed. A relation between the thickness of the films determined, from QCM technique and the optical absorption of the films was established. The electrical conductivity of the PANI films was also measured.     

Polyaniline film deposition from the oxidative polymerization of aniline using K2Cr2O7

The deposition of the polyaniline (PANI) films was monitored using the quartz crystal microbalance (QCM) technique. The films were grown from an aqueous dilute hydrochloric acid solution by the chemical oxidation of aniline using potassium dichromate (KDC). The effect of the initial molar ratio of the KDC/aniline on the yield and the growth rate of the PANI films were studied. There is no optimum initial molar ratio of KDC/aniline of PANI film deposition. Also there was a small depletion period and no degradation to the deposited PANI films. The order of the polymerization kinetics was studied with respect to KDC. The UV-visible spectra of the PANI films grown onto a glass support immersed into the bulk solution were measured. The absorption of the PANI film with the time of polymerization was compared to the growth of the PANI film thickness with time determined from the QCM technique. The characteristics of the PANI film deposition were compared to the corresponding ones that were observed during the oxidative polymerization of aniline with ammonium persulphate (APS).     

A comparative study on the viscoelasticity and morphology of polyaniline films galvanostatically grown on bare and 4-aminothiophenol-modified gold electrodes using an electrochemical quartz crystal impedance system and SEM.

The equivalent-circuit parameters of the 9-MHz piezoelectric quartz crystal (PQC) resonance were measured in situ during the galvanostatic polymerization of aniline on 4-aminothiophenol(4-ATP)-modified and bare Au electrodes for ca. 2000 s, respectively. Two polymerization media, 0.100 mol L-1 aniline in 1.0 mol L-1 H2SO4 and in 2.0 mol L-1 HClO4 aqueous solutions, and two values of the current density, 12 and 36 microA cm-2, were used. At identical levels of the resonant frequency shifts in the solutions, obviously greater increases in the motional resistance (R1) were found after aniline polymerization on bare Au electrodes, though the absolute values of delta f0/delta R1 were all large; also, the resonant frequency shifts in air (delta f0g) were considerably smaller for PANI films grown on bare Au electrodes. It is thus concluded that, under identical polymerization conditions, (1) the PANI film grown on a bare gold electrode is rougher, less compact, and can entrap solution more notably; (2) the deposition efficiency of PANI is higher on a 4-ATP-modified Au electrode, owing to a significantly greater observed "dry" frequency shift, and thus a greater "net" mass value of the polyaniline backbone. SEM observations have confirmed that PANI films on 4-ATP-modified Au electrodes were smoother and more compact than those grown on bare Au ones under identical polymerization conditions. In addition, a technique of simultaneous measurements of the electroacoustic admittance of the PQC resonance and the electrochemical impedance was used to monitor the adsorption of 4-ATP onto a PQC gold electrode.     

纳米纤维聚苯胺膜在不锈钢电极表面的生长过程

研究了脉冲电流法(PGM)聚合苯胺时, 纳米纤维聚苯胺(PANI)膜在不锈钢(SS)电极表面的生长过程. 用计时电位法和扫描电子显微镜(SEM)表征了聚苯胺生长过程的电化学特征和微观形貌; 并通过循环伏安(CV)法研究了苯胺的聚合速率. 结果表明, 聚苯胺的生长经历了两个阶段, 首先是在裸不锈钢电极表面上形成颗粒状聚苯胺, 此时聚合电位约为1.10 V, 经历了30 s后, 电极表面被一层颗粒状聚苯胺膜所覆盖; 在此基础上, 聚苯胺以纳米纤维状结构继续生长, 当颗粒状聚苯胺被纳米纤维状聚苯胺膜完全覆盖时, 聚合电位降至0.75 V左右并保持稳定.     

聚苯胺薄膜电极上循环伏安法可逆波理论和验证

提出了聚苯胺薄膜电极上循环伏安法可逆波方程式，对伏安曲线的性质进行了详细的讨论。聚苯胺薄膜电极是利用浓度为１．０９ｍｏｌ／Ｌ苯胺溶液（内含２．０ｍｏｌ／Ｌ ＨＣｌ）在铂电极上用恒电流（０．０１－０．１ｍＡ／ｃｍ＾２）使苯胺发生氧化反应进而经聚合获得。结果表明，该法得到的聚苯胺膜具有良好的均匀度和单一性。在１０ｍｏｌ／Ｌ ＨＣｌ底液中获得的循环伏安曲线与理论结果相符合。     

Inkjet printable polyaniline nanoformulations

Aqueous polyaniline (PANI) nanodispersions doped with dodecylbenzenesulfonic acid (DBSA) were synthesized and successfully inkjet-printed using a piezoelectric desktop printer. This paper examines the optimization and characterization of the nanoparticulate formulation for optimal film electrochemistry and stability. PANI nanoparticle synthesis was optimized in terms of the ratio of monomer (aniline) to oxidant (ammonium persulphate, APS) and dopant (DBSA). Particle size, UV-vis spectroscopy, electrochemical, and conductivity analyses were performed on all materials. Optimal synthesis conditions were found to be at a molar ratio of 1.0:0.5:1.2 aniline/APS/DBSA. This resulting nanodispersion showed a uniform particle size distribution of approximately 82 nm, and UV-vis analysis indicated a high doping level. These synthetic conditions resulted in the highest conductivity, and the electrochemistry of the resulting films was well-defined and stable. Surface tension analysis and rheological studies demonstrated that the aqueous nanodispersions were suitable for inkjet printing. Successful inkjet printing of these polyaniline nanoparticulate formulations is demonstrated.