LiBOB对Li_(1.15)Ni_(0.68)Mn_(1.32)O_4电极电化学行为的影响

采用恒电流充放电技术研究了锂离子电池电解液添加剂双草酸硼酸锂(Li BOB)对Li1.15Ni0.68Mn1.32O4电极电化学性能的影响,用X射线衍射(XRD)、衰减全反射傅里叶变换红外光谱(FTIR-ATR)、电感耦合等离子体发射光谱(ICP)、扫描电子显微镜(SEM)和电化学阻抗谱(EIS)分析了Li BOB对Li1.15Ni0.68Mn1.32O4电极性能的影响.结果显示,Li BOB作为电解液添加剂能显著改善Li1.15Ni0.68Mn1.32O4电极的循环性能,原因是Li BOB在充放电过程中会在Li1.15Ni0.68Mn1.32O4电极表面发生分解,分解产物在电极表面沉积形成固体电解质界面(SEI)膜,SEI膜能够有效抑制Li1.15Ni0.68Mn1.32O4电极材料中Mn的溶解,确保其晶体结构的稳定性,从而提高Li1.15Ni0.68Mn1.32O4电极的循环性能.     

高电压镍锰酸锂正极/电解液界面本征性质的研究

高电压正极材料的应用是提高锂离子电池能量密度的有效手段,然而高电压下正极/电解液界面稳定性成为决定锂离子电池在高电压工作条件下循环性能和安全性能的关键因素,因此高电压下正极/电解液界面具有重要的研究价值. 但是,目前报道的正极/电解液界面的研究中通常使用传统的极片制备方法,这需要引入导电剂和粘结剂,会对后期正极活性物质表面钝化膜的形貌和组分表征带来干扰,甚至造成固体电解质界面(SEI)膜存在的假象,难以获得正极材料与电解液之间界面的本征信息. 这里,我们采用溶胶凝胶旋涂法制备了不含导电剂和粘结剂的镍锰酸锂(LNMO)正极,以其为研究对象,通过扫描电镜(SEM)、原子力显微镜(AFM)和X射线光电子能谱(XPS)技术,结合电化学阻抗谱(EIS)研究了LNMO正极/电解液界面在充放电过程中的结构演变过程以及本征性质. 研究结果显示在充放电过程中,电解液中溶剂和电解质都会参与反应,其中LiPF₆的降解主要发生在高电压下,其降解产物在放电过程中又会被反应消耗掉. 它们的降解产物沉积到LNMO正极形成表面膜,该表面膜的主要成分随着电压的不同组分有所不同.     

Ni-Mn共掺杂高电压钴酸锂锂离子电池正极材料

以金属硫酸盐为原料,Na OH和NH3·H2O为沉淀剂,用共沉淀法合成了Co0.9Ni0.05Mn0.05(OH)前驱体,再进行配锂并通过高温固相法合成了Ni-Mn共掺杂高电压钴酸锂锂离子电池正极材料Li(Co0.9Ni0.05Mn0.05)O2。用X射线衍射(XRD)、扫描电镜(SEM)、循环伏安(C-V)、交流阻抗(EIS)和充放电测试研究样品的晶体结构、形貌和电化学性能。结果表明Ni-Mn共掺杂正极材料Li(Co0.9Ni0.05Mn0.05)O2有优秀的电化学性能:在3.0~4.4 V和3.0~4.5 V区间,0.5C倍率下首次放电比容量分别为162.5 m Ah·g-1和185 m Ah·g-1,循环100次后容量保持率分别为94.4%和93.7%。     

无机聚合物正极材料聚三硫代磷氮烯的制备与表征

合成了无机化合物聚三硫代磷氮烯[NPS3]n,借助红外光谱与元素分析测试确定了聚合物的重复单元结构;并通过比表面积分析、粒度测试和扫描电子显微镜观察了无机聚合物材料的微观形貌;热重分析测试表明材料在300℃以下能够稳定使用;循环伏安实验发现,作为锂二次电池正极材料使用,聚三硫代磷氮烯的电化学还原反应在2.25 V(versus Li/Li+)发生,其可逆的电化学氧化反应在2.51 V(versus Li/Li+)进行;充放电测试显示这种无机材料具有745.2 mAh.g-1的首次放电容量,与理论值(759.0 mAh.g-1)十分接近,经过60次充放电循环后放电容量保持在708.8 mAh.g-1,容量保持率95.1%,循环性能优秀.     

腈基功能化有机硅基电解液在4.4V钴酸锂/石墨锂离子电池中的性能研究

研究了3-丙基腈-甲氧基乙氧基-二甲基硅烷(SN1)作为电解液共溶剂对高电压钴酸锂/石墨全电池电化学性能的影响.在商业烷基碳酸酯电解液里掺入30%SN1(体积分数),钴酸锂/石墨全电池在4.4 V截止电压下仍表现出良好的循环稳定性和倍率性能:以0.5 C充放电,首次放电比容量为154 mA h/g,循环150周后,容量保持率为92.9%;当放电倍率增加到1和1.5 C时,放电容量分别为143和133 mA h/g.电化学阻抗谱、扫描电镜和傅里叶红外光谱的结果表明,耐高电压腈基功能化有机硅化合物的引入有效抑制了共溶剂电解液在正极材料表面的分解,压制了循环过程中电极极化的增长,为电极/电解液界面的Li+扩散和电荷转移提供了有利的动力学条件.     

高电压锂离子电池用环丁砜基高浓度电解液

本文介绍了一种含双(三氟甲烷磺酰)亚胺锂(Li TFSI)和环丁砜(TMS)的高浓度电解液。采用FT-IR对样品进行结构表征,通过线性扫描伏安法(LSV)和循环伏安法(CV)研究电解液的电化学性能。结果表明,高浓度TMS/Li TFSI(摩尔比2∶1)电解液的电化学和化学稳定性良好,电化学窗口拓宽至5. 02V,可以有效抑制Al箔腐蚀,适用于5V级的镍锰酸锂(Li Ni_(0.5)Mn1. 5O4)正极材料。室温下,基于TMS/Li TFSI高浓度电解液的Li Ni_(0.5)Mn1. 5O4半电池经过大倍率充放电后,0. 1C的比容量基本回复到原始状态;在0. 2C的倍率下实现良好的循环,前25圈的库仑效率大于92%。     

锂离子电池正极界面修饰用电解液添加剂

提高电压是提高锂离子电池比能量的重要途径之一。例如,LiNi_0.5Mn_1.5O₄(4.7 V)、LiNiPO₄(5.1 V)和富锂锰基等电极材料在较高的充电截止电压下表现出较高的能量密度和较低的成本,具有很好的应用前景。另外,提高LiCoO₂和三元电池体系的充电截止电压是提升电池能量密度的简单有效措施。但是,当电池充电截止电压提高时,不仅会造成电解液在正极/电解液界面的氧化分解,还会加速正极中金属阳离子在电解液中的溶解,造成电池循环性能和安全性下降。采用不同的正极界面修饰用电解液添加剂,既可以有效钝化正极/电解液界面,抑制电解液的分解,还可以有效抑制正极结构的破坏。本文从添加剂的分子结构出发,介绍了磺酸酯、硼酸酯、磷酸酯、氟代碳酸酯、腈类、酸酐和锂盐等添加剂在正极界面的相关研究成果,并对不同添加剂的作用机理进行了详细的解释和归纳;另外,介绍了添加剂的联用技术在不同电池体系中的最新研究成果;最后,对新型正极界面修饰用电解液添加剂的开发进行了展望。     

Li3V2（PO4）3/C正极材料在不同电压区间的电化学行为及容量衰减原因

采用溶胶-凝胶法制备锂离子电池正极材料Li3V2(PO4)3/C.通过恒电流充放电测试、循环伏安(CV)、电化学阻抗谱(EIS)等方法,研究了Li3V2(PO4)3/C在不同电压区间的电化学行为(3.0-4.5 V和3.0-4.8 V).结果表明,3.0-4.8 V电压区间的循环性能和倍率性能均不及3.0-4.5 V电压区间的.3.0-4.5 V区间0.1C (1C=150 mA?g-1)倍率首次放电比容量为127.0 mAh?g-1,循环50次后容量保持率为99.5%,而3.0-4.8 V区间的分别为168.2 mAh?g-1和78.5%.经过高倍率测试后再回到0.1C倍率充放电,3.0-4.5 V和3.0-4.8 V的放电比容量分别为初始0.1C倍率的99.0%和80.7%.经过3.0-4.8 V电压区间测试后,少部分第三个锂离子能够在低于4.5 V的电压脱出,使3.0-4.5 V电压区间的放电比容量提升了7.4%. CV结果表明3.0-4.8 V区间的容量损失主要表现为第一个锂离子的不可逆损失.极片的X射线衍射(XRD)和X射线光电子能谱(XPS)分析测试结果表明经过3.0-4.8 V测试后, Li3V2(PO4)3的结构发生了轻微的改变.电感耦合等离子体(ICP)测试结果表明循环后的电解液中含有少量的V.结构变形和V溶解可能是Li3V2(PO4)3在3.0-4.8 V区间容量衰减的主要原因.     

Li_2CO_3添加剂对石墨电极性能的影响

运用电化学阻抗谱(EIS)和循环伏安法(CV)研究了在1mol/LLiPF6-EC(碳酸乙烯酯):DMC(碳酸二甲酯)电解液中添加Li2CO3对石墨电极性能的影响及机制.CV研究结果表明,在1mol/LLiPF6-EC:DMC电解液中添加Li2CO3能够有效抑制石墨电极首次充放电过程中碳酸乙烯酯(EC)的单电子还原过程,即还原分解产生乙烯和碳酸锂的过程,进而改善石墨电极的电化学循环性能.EIS研究结果表明,在添加Li2CO3的1mol/LLiPF6-EC:DMC电解液中,石墨电极表面的固体电解质相界面膜(SEI膜)具有较强的黏弹性,可以更好地适应锂离子嵌入过程中石墨颗粒体积的微小变化,从而使锂离子的嵌入过程更容易进行.     

高镍三元正极材料的表面包覆策略

锂离子电池(LIBs)因具有更高的重量/体积能量密度、 更长的使用寿命、 更低的自放电率等优点而逐渐被广泛应用. 相比于已经广泛使用的钴酸锂和磷酸铁锂等正极材料, 高镍三元正极材料Li[Ni_1-x-yCo_xMn_y]O₂(NCM)以其高电压和高容量等优点, 逐渐成为下一代高能锂离子电池的首选正极材料之一. 尽管高镍NCM正极材料具有上述优点, 但在进一步的实际应用前还需解决其循环稳定性、 倍率性能和安全性等问题, 这些问题主要源于NCM材料本身的晶体结构不稳定、 正极-电解液间界面副反应及高界面电阻等. 针对这些问题, 目前对高镍NCM正极电化学性能优化的大量研究都与电极-电解液界面有关, 如何通过改善界面稳定性、 增加离子在固液界面的迁移率、 抑制界面副反应、 提高正极材料的稳定性进而改善电池性能成为了关注焦点. 本文总结了目前对于其电化学性能衰减的机理解释, 分类概括了包括电化学惰性包覆锂、 残积物清除剂包覆和锂离子良导体包覆等对于高镍NCM正极材料的颗粒表面包覆策略, 简述了一些新兴的包覆策略, 并对高镍NCM正极材料的发展方向和前景提出了展望.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.