Application of Double-Phase Liquid Phase Microextraction in the Determination of Partition Coefficients and Analysis of Pesticides in Water Samples

A simple and solvent-minimized sample preparation technique based on two-phase hollow fiber-protected liquid-phase microextraction has been developed and used for the determination of partition coefficient and analysis of selected pesticides in environmental water samples. The analysis was performed by gas chromatography–electron capture detector. Three pesticides namely hexaconazole, quinalphos, and methidathion were considered as target analytes. Extraction conditions such as solvent identity, salt concentration, stirring speed, extraction time, length of the hollow fiber, and volume of donor phase were optimized. The analytes were extracted from a donor phase (water sample) through 3 μL of an organic solvent immobilized in the pores of a porous polypropylene hollow fiber and then into the acceptor phase present inside the hollow fiber. Excellent extractions of the analytes were achieved under the optimized conditions, with relative standard deviations of 4.6–7.9%, correlation coefficients (r ²) of 0.9954–0.9986 and limits of detection of 3–7 ng L^?1. The proposed method provided good average enrichment factors of up to 250-fold. The partition coefficients of the analytes determined were found to be directly correlated with the enrichment factor. The present methodology also confirms the robustness of microextraction for monitoring trace levels of pesticides in environmental water samples.     

Two-phase/Three-phase Hollow Fibre Liquid-Phase Simultaneous Microextraction Combined with HPLC for Analysis of Phenolic Acids and Flavonoids in Traditional Chinese Medicine

A two-phase/three-phase hollow fibre liquid-phase simultaneous microextraction (2p/3p-HF-LPSME) method, coupled with high-performance liquid chromatography and ultraviolet detection, was developed and introduced for simultaneous extraction and determination of phenolic acids and flavonoids in Lonicera japonica, Herba Taraxaci and Cortex Eucommiae. Several factors affecting performance were investigated and optimized, including the type of hollow fibre liquid-phase microextraction, extraction solvent, pHs of the sample and acceptor phases, extraction time, stirring rate, salt concentration in the sample solution and volume of sample phase. Under optimised conditions, the enrichment factors of 2p/3p-HF-LPSME for analytes ranged from 9 to 171, and good linearities were obtained for all analytes with regression coefficients of between 0.9939 and 0.9996. In addition, the limits of detection were between 0.3 and 4.0 ng·mL⁻¹, and satisfactory recoveries (90.0–106.3 %) and precisions (RSD 2.3–10.4 %) were also achieved. The simultaneous microextraction mechanism of the approach was also analysed and described. Experimental results show that the method is simple, sensitive, practical and effective, and it can be used for simultaneous preconcentration and determination of phenolic acids and flavonoids in traditional Chinese medicines.

     

Determination of Trace Chloroanilines in Environmental Water Samples Using Hollow Fiber-Based Liquid Phase Microextraction

A liquid phase microextraction method using hollow fiber to support extraction solvent was developed for enrichment of trace level chloroanilines in environmental water samples. Target analytes, 2-chloroaniline, 3-chloroaniline, 2,3-dichloroaniline, 2,4-dichloroaniline, 3,4-dichloroaniline, and 3,5-dichloroaniline were determined using gas chromatography-flame ionization detector after extraction. Experimental conditions that affect extraction efficiency were investigated and optimized. The proposed method showed a wide linear range from lower ??g L^?1 to 1,000 ??g L^?1, low detection limits (??5.1 ??g L^?1), and reasonable relative standard deviations (RSDs < 13%). Feasibility of the method was evaluated by analyzing river water samples collected from the Hudson River and the East River in New York City.     

Hollow‐fiber solvent bar microextraction with gas chromatography and electron capture detection determination of disinfection byproducts in water samples

A liquid‐phase microextraction method that uses a hollow‐fiber solvent bar microextraction technique was developed by combining gas chromatography with electron capture detection for the analysis of four trihalomethanes (chloroform, dichlorobromomethane, chlorodibromomethane, and bromoform) in drinking water. In the microextraction process, 1‐octanol was used as the solvent. The technique operates in a two‐phase mode with a 5 min extraction time, a 700 rpm stirring speed, a 30°C extraction temperature, and NaCl concentration of 20%. After microextraction, one edge of the membrane was cut, and 1 μL of solvent was collected from the membrane using a 10 μL syringe. The solvent sample was directly injected into the gas chromatograph. The analytical characteristics of the developed method were as follows: detection limits, 0.017–0.037 ng mL⁻¹; linear working range, 10–900 ng mL⁻¹; recovery, 74 ± 9–91 ± 2; relative standard deviation, 5.7–10.3; and enrichment factor, 330–455. A simple, fast, economic, selective, and efficient method with big possibilities for automation was developed with a potential use to apply with other matrices and analytes.     

Development of a novel hollow‐fiber liquid‐phase microextraction based on oil‐in‐salt and its comparison with conventional one

A novel hollow‐fiber liquid‐phase microextraction based on oil‐in‐salt was proposed and introduced for the simultaneous extraction and enrichment of the main active compounds of hesperidin, honokiol, shikonin, magnolol, emodin, and β,β′‐dimethylacrylshikonin in a formula of Zi‐Cao‐Cheng‐Qi decoction and the single herb, Fructus Aurantii Immaturus , Cortex Magnoliae Officinalis , Radix et Rhizoma , and Lithospermum erythrorhizon , composing the formula prior to their analysis by high‐performance liquid chromatography. The results obtained by the proposed procedure were compared with those obtained by conventional hollow‐fiber liquid‐phase microextraction, and the proposed procedure mechanism was described. In the procedure, a hollow‐fiber segment was first immersed in organic solvent to fill the solvent in the fiber lumen and wall pore, and then the fiber was again immersed into sodium chloride solution to cover a thin salt membrane on the fiber wall pore filling organic solvent. Under the optimum conditions, the enrichment factors of the analytes were 0.6–109.4, linearities were 0.002–12 μg/mL with r ² ≥ 0.9950, detection limits were 0.6–12 ng/mL, respectively. The results showed that oil‐in‐salt hollow‐fiber liquid‐phase microextraction is a simple and effective sample pretreatment procedure and suitable for the simultaneous extraction and concentration of trace‐level active compounds in traditional Chinese medicine.     

Comparison of three‐phase hollow fiber liquid‐phase microextraction based on reverse micelle with conventional two‐phase hollow fiber liquid‐phase microextraction and their applications for analysis of cinnamic acids in traditional Chinese medicines

A novel three‐phase hollow fiber liquid‐phase microextraction was developed based on reverse micelle as extraction solvent and acceptor phase, and compared with conventional two‐phase hollow fiber liquid‐phase microextraction. Both procedures were used in the extraction and concentration of four cinnamic acids (caffeic acid, p‐hydroxycinnamic acid, ferulic acid, and cinnamic acid) in traditional Chinese medicines prior to high‐performance liquid chromatography analysis. Parameters affecting the two procedures were investigated and optimized to obtain the optimum enrichment factors. The mechanism of the developed procedure was explored and elucidated by comparison with conventional two‐phase hollow fiber liquid‐phase microextraction. Under the optimized conditions, the analytes’ enrichment factors were between 50 and 118 for the proposed procedure, and 31–96 for conventional two‐phase mode. Satisfactory linear ranges (r² ≥ 0.99), detection limits (0.1–0.6 ng/mL), precisions (<9.2%), and accuracies (recoveries: 80–123.1%) were observed for the two procedures. The results showed that the enrichment capacity of the proposed procedure for the cinnamic acids is better than that of conventional two‐phase procedure, and both are eco‐friendly, simple, and effective for the enrichment and detection of cinnamic acids in traditional Chinese medicines.     

Rapid Determination of DDT and Its Metabolites in Environmental Water Samples with Mixed Ionic Liquids Dispersive Liquid–Liquid Microextraction Prior to HPLC-UV

In this paper, a novel mixed ionic liquids-dispersive liquid–liquid microextraction method was developed for rapid enrichment and determination of environmental pollutants in water samples. In this method, two kinds of ionic liquids, hydrophobic ionic liquid and hydrophilic ionic liquid, were used as extraction solvent and disperser solvent, respectively. DDT and its metabolites were used as model analytes and high-performance liquid chromatography with ultraviolet detector for the analysis. Factors that may affect the extraction recoveries, such as type and volume of extraction solvent (hydrophobic ionic liquid) and disperser solvent (hydrophilic ionic liquid), extraction time, sample pH and ionic strength, were investigated and optimized. Under the optimum conditions, the linear range was 1–100 μg L⁻¹, limits of detection could reach 0.21–0.49 μg L⁻¹, and relative standard deviation was 6.01–8.48 % (n = 7) for the analytes. Satisfactory results were achieved when the method was applied to analyze the target pollutants in environmental water samples with spiked recoveries over the range of 85.7–106.8 %.

     

Determination of lignans in Wuweizi by using magnetic bar microextraction and HPLC

In this paper, a magnetic bar microextraction was developed to extract schisandrin A, schisantherin A, and deoxyschizandrin from Wuweizi. The analytes were determined by HPLC. A stainless‐steel wire was inserted into the hollow of the hollow fiber to make the magnetic bar. The bar can be used to stir the extraction system and extract the analytes, and was isolated from the extract system by magnetic force. Several experimental parameters, including type and volume of extraction solvent, the number of magnetic bars, extraction temperature and time, stirring speed and NaCl concentration were investigated and optimized. The LODs for schisandrin A, schisantherin A, and deoxyschizandrin were 0.14, 0.06, and 0.10 μg/mL, respectively. The recoveries were in the range of 70.90–106.67% and the RSDs were < 8.84%. Compared with ultrasound‐assisted and Soxhlet extraction, when the present method was applied, the extraction time was shorter, the sample amount was smaller, and the consumption of organic solvent was lower.     

Determination of hormones in milk by hollow fiber-based stirring extraction bar liquid–liquid microextraction gas chromatography mass spectrometry

The hollow fiber-based stirring extraction bar liquid–liquid microextraction was applied to the extraction of hormones, including 17-α-ethinylestradiol, 17-α-estradiol, estriol, 17-β-estradiol, estrone, 17-α-hydroxyprogesterone, medroxyprogesterone, progesterone and norethisterone acetate, in milk. The present method has the advantages of both hollow fiber-liquid phase microextraction and stirring bar sorptive extraction. The stirring extraction bar was used as both the stirring bar of microextraction, and extractor of the analytes, which can make extraction, clean-up and concentration be carried out in one step. When the extraction was completed, the stirring extraction bar was easy isolated from the extraction system with the magnet. Several experimental parameters, including the type of extraction solvent, the number of hollow stirring extraction bar, extraction time, stirring speed, ionic strength, and desorption conditions were investigated and optimized. The analytes in the extract were derived and determined by gas chromatography mass spectrometry. Under optimal experimental conditions, good linearity was observed in the range of 0.20–20.00 ng mL⁻¹. The limits of detection and quantification were in the range of 0.02–0.06 ng mL⁻¹ and 0.07–0.19 ng mL⁻¹, respectively. The present method was applied to the analysis of milk samples, and the recoveries of analytes were in the range of 93.6–104.6% with the relative standard deviations ranging from 1.6% to 6.2% (n = 5). The results showed that the present method was a rapid and feasible method for the determination of hormones in milk samples.     

Three‐phase hollow‐fiber liquid‐phase microextraction based on deep eutectic solvent as acceptor phase for extraction and preconcentration of main active compounds in a traditional Chinese medicinal formula

A three‐phase hollow‐fiber liquid‐phase microextraction based on deep eutectic solvent as acceptor phase was developed and coupled with high‐performance capillary electrophoresis for the simultaneous extraction, enrichment, and determination of main active compounds (hesperidin, honokiol, shikonin, magnolol, emodin, and β,β′‐dimethylacrylshikonin) in a traditional Chinese medicinal formula. In this procedure, two hollow fibers, impregnated with n‐heptanol/n‐nonanol (7:3, v/v) mixture in wall pores as the extraction phase and a combination (9:1, v/v) of methyltrioctylammonium chloride/glycerol (1:3, n/n) and methanol in lumen as the acceptor phase, were immersed in the aqueous sample phase. The target analytes in the sample solution were first extracted through the organic phase, and further back‐extracted to the acceptor phase during the stirring process. Important extraction parameters such as types and composition of extraction solvent and deep eutectic solvent, sample phase pH, stirring rate, and extraction time were investigated and optimized. Under the optimal conditions, detection limits were 0.3–0.8 ng/mL with enrichment factors of 6–114 for the analytes and linearities of 0.001–13 μg/mL (r² ≥ 0.9901). The developed method was successfully applied to the simultaneous extraction and concentration of the main active compounds in a formula of Zi‐Cao‐Cheng‐Qi decoction with the major advantages of convenience, effectiveness, and environmentally friendliness.     

Applications of titania and zirconia hollow fibers in sorptive microextraction of N,N-dimethylacetamide from water sample

The convenient fabrications of titania and zirconia hollow fiber with three-dimensional porous structure using polypropylene hollow fibers as templates were developed. And an analytical method based on enrichment and extraction of analytes in the water sample, hollow fiber sorptive microextraction in combined with gas chromatography has been developed for the rapid analysis of N,N-dimethylacetamide (DMA) in the environmental samples. The results showed that zirconia hollow fiber gave higher extraction performance of DMA than that of titania hollow fiber. The method validations, including linearity, limit of detection, limit of qualification, precision, and repeatability were investigated. Linearity for six-point calibration curve was excellent with zirconia hollow fiber having r² value greater than 0.9993 at the linearity range of 0.001-1.0 mg mL⁻¹. In addition, it seems that hollow fiber sorptive extraction is a promising technique for the enrichment and purification of analytes extracted directly from liquid samples without any other pretreatment.     

Development of a stir bar sorptive extraction method coupled to solidification of floating droplets dispersive liquid–liquid microextraction based on deep eutectic solvents for the extraction of acidic pesticides from tomato samples

A stir bar sorptive extraction method coupled with deep eutectic solvent based solidification of floating organic droplets–dispersive liquid–liquid microextraction has been used for the simultaneous derivatization and extraction of some acidic pesticides in tomato samples. In this method, initially the analytes are adsorbed on a coated stir bar from tomato juice filled in a narrow tube. After extraction, the stir bar is removed and a water–miscible deep eutectic solvent is used to elute the analytes. Afterward, a derivatization agent and a water–immiscible deep eutectic solvent (as an extraction solvent) with melting point near to room temperature are added to the obtained eluant at µL–levels and the obtained mixture is rapidly injected into deionized water. Under the optimum conditions, the introduced method indicated high enhancement (1543–3353) and enrichment (2530–2999) factors, low limits of detection (7–14 ng/L) and quantification (23–47 ng/L), good linearity (r² ≥ 0.9982), and satisfactory repeatabilities (relative standard deviation ≤12% for intra– and inter–day precisions at a concentration of 100 ng/L of each analyte). Finally, the proposed method was applied in analysis of the analytes in tomato samples.     

Novel Microporous Membrane/Solvent Microextraction for Preconcentration of Cinnamic Acid Derivatives in Rhizoma Typhonii

A novel microporous membrane/solvent microextraction (MPMSME) approach was developed in which a piece of microporous filter membrane was used as not only extraction solvent holder but also solid phase extraction unit. Subsequently, high-performance liquid chromatography with an UV detector was conducted. The wide exchange surface and very little organic solvent consumption made this sample pretreatment technology very interesting. The cinnamic acid derivatives were used as model analytes to evaluate the procedure. Parameters that affect the MPMSME such as type of extraction solvent, membrane area (or volumes of extraction solvent), aqueous phase pH, ionic strength, extraction stirring rate, extraction time, and sample volume were investigated and optimized. The enrichment factor (EF) of analyte was defined in MPMSME. Under the optimized conditions, the EFs of cinnamic acid derivatives were 43–144. Good linearities were obtained from 4 to 4,000 ng mL^?1 for all the analytes with regression coefficients of between 0.9956 and 0.9977; the limits of quantification were below 0.4 ng mL^?1, and satisfactory recoveries (93–106 %) and precisions (0.37–13 %) were also achieved. The experimental results showed that the method was simple, rapid, practical, and effective for preconcentration and determination of the cinnamic acid derivatives in rhizoma typhonii.     

Ultrasonic nebulization extraction coupled with headspace hollow fiber microextraction of pesticides from root of Panax ginseng C.A. Mey

The ultrasonic nebulization extraction coupled with headspace hollow fiber microextraction (UNE-HS-HFME) was applied for the extraction of pesticides from root of Panax ginseng C.A. Mey. Experimental parameters, which affect the performances of ultrasonic nebulization extraction coupled with headspace hollow fiber microextraction, such as the kind of acceptor solvent in the pore of the fiber wall, the sample amount, extraction time, salt concentration in extraction solvent, pH of the acceptor solution, the elution time, and times were studied and optimized. The analytes were determined by high-performance liquid chromatography. The detection limits for simeton, monolinuron, chlortoluron, karmex, and prebane are 20.9, 18.4, 18.2, 12.4, and 22.2 μg/kg, respectively. Besides volatile and semi-volatile compounds, the non-volatile compounds also can be determined by the proposed method. The extraction and enrichment process can be performed simultaneously.     

Magnetic Stirring-Assisted Dispersive Suspended Microextraction with Solidification of a Floating Organic Droplet for the Determination of Trace Fungicides in Water and Wine

For the first time, a simple method for magnetic stirring-assisted dispersive suspended microextraction has been developed for the determination of three fungicides (azoxystrobin, diethofencarb, and pyrimethanil) in water and wine samples. The method is based on the solidification of a floating organic droplet coupled with high performance liquid chromatography. In the proposed method, the low toxicity solvent 1-dodecanol was used as the extractant. Both the extraction and phase separation process were performed with magnetic stirring. No centrifugation step was involved. After separating the two phases, the extraction solvent droplet was easily collected through solidification at lower temperature. Important parameters such as the kind and volume of organic extraction solvent, extraction and restoration speed, extraction and restoration time, and salt concentration were optimized. Under the optimal conditions, the limits of detection for the analytes varied from 0.14 to 0.26 µg L^?1. The enrichment factors ranged from 125–200. The linearity ranges were 1–2000 µg L^?1, yielding correlation coefficients (r) higher than 0.9990. The relative standard deviation (n = 6) at two spiked level of 0.2 µg mL^?1 and 4 µg L^?1 varied between 2.2% and 7.8%. Finally, the developed technique was successfully applied to determine target fungicides in real water and wine samples, where the obtained recoveries ranged from 83.8–105.3%     

Solvent bar microextraction combined with high‐performance liquid chromatography for preconcentration and determination of pramipexole in biological samples

A simple, rapid and sensitive analytical method for preconcentration and determination of pramipexole in different biological samples has been developed using solvent bar microextraction (SBME) combined with HPLC‐UV. The target drugs were extracted from 10 mL of basic aqueous sample solution into an organic extracting solvent located inside the pores of a polypropylene hollow fiber, then back‐extracted into an acidified aqueous solution in the lumen of the hollow fiber. In order to obtain high extraction efficiency, the effect of different variables on the extraction efficiency was studied simultaneously using an experimental design. The experimental parameters of SBME were optimized using a Box–Behnken design after a Plackett–Burman screening design. Under the optimized conditions, an enrichment factor up to 96 was achieved and the relative standard deviation of the method was 4.64% (n = 5). The linear range was 0.05–2000 µg/L with a correlation coefficient (r) of 0.987. Finally, the applicability of the proposed method was evaluated by extraction and determination of pramipexole in plasma and urine samples. The results indicated that SBME method has excellent clean‐up and high preconcentration factor and can serve as a simple and sensitive method for analysis of pramipexole in biological samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Liquid-liquid-liquid microextraction of nitrophenols with a hollow fiber membrane prior to capillary liquid chromatography

A simple liquid-liquid-liquid microextraction device utilizing a 2 cm x 0.6 mm I.D. hollow fiber membrane was used to preconcentrate nitrophenols from water sample prior to capillary liquid chromatography (cLC) analysis. The extraction procedure was induced by the pH difference inside and outside the hollow fiber. The donor phase outside the hollow fiber was adjusted to pH approximately 1 with HCl; the acceptor phase was NaOH solution used at various concentrations. Organic solvent was immobilized into the pores of the hollow fiber. With stirring, the neutral nitrophenols outside the fiber were extracted into the organic solvent, then back extracted into 2 microl of basic acceptor solution inside the fiber. The acceptor phase was then withdrawn into a microsyringe and injected into the cLC system directly. This technique used a low-cost disposable extraction "device" and is very convenient to operate. Up to 380-fold enrichment of analytes could be achieved. This procedure could also serve as a sample clean-up step because large molecules and basic compounds were not extracted into the acceptor phase. The RSD (n=6) was less than 6.2%, while the linear calibration range was from 1 to 200 microg/ml with r>0.998. The procedure was applied to the analysis of seawater.     

Three-Phase Solvent Bar Microextraction Combined with HPLC for Extraction and Determination of Plasma Protein Binding of Bisoprolol

A three-phase solvent bar microextraction (TPSBME) technique combined with high performance liquid chromatography (HPLC)?Cfluorescence detection was evaluated for the quantitative determination of plasma protein binding of bisoprolol. Bisoprolol was extracted from a 5.6-mL basified plasma sample (donor phase) into the organic solvent (n-octanol) impregnated in the pores of a hollow fiber and then extracted into an acidic solution (acceptor phase) inside the lumen of the hollow fiber. Metoprolol was used as the internal standard. Several parameters influencing the efficiency of the method were investigated and optimized including organic solvent (n-butanol, n-octanol, dibutyl phthalate, dihexyl ether), stirring rate (100?C1,000 rpm), extraction time (5?C35 min), extraction temperature (15?C45 °C), concentration of the donor phase (0.1?C2 M NaOH) and the acceptor phase (0.5?C5 M formic acid), salt concentration (2.5?C10%, w/v). Under the optimal condition, extraction recoveries from plasma samples were above 61.4% for bisoprolol. The calibration curves were obtained in the range of 10?C100 ng mL^?1 with reasonable linearity (r > 0.994). The method was successfully applied to determine the plasma protein binding rate of bisoprolol.     

Hollow-Fibre Liquid-Phase Microextraction for the Determination of Polycyclic Aromatic Hydrocarbons in Johannesburg Jukskei River, South Africa

A simple, rapid and environmentally friendly hollow-fibre liquid-phase microextraction (HF-LPME) technique was developed for the quantitative determination of polycyclic aromatic hydrocarbons (PAHs) in aqueous samples. GC-MS was then used as the method of analysis. The HF-LPME technique involves extraction of PAHs from a 20-mL sample containing 20 % acetonitrile as a modifier. The PAHs were extracted into a 5-cm hollow fibre filled with heptane as organic solvent. At a stirring speed and extraction time of 600 rpm and 30 min, respectively, the acceptor solvent was then collected to be analysed. Parameters that affect the extraction efficiency were optimised in order to achieve high enrichment of the analytes. In order to evaluate the practical applicability of the HF-LPME technique, the performance of the method was compared to solid-phase extraction using spiked deionised water and real water samples. The obtained concentration enrichment factors ranged from 48 to 95 for HF-LPME and 81–135 for SPE, depending on the individual PAH. The detection limit ranged from 23 to 95 ng L^?1 for HF-LPME and 20–52 ng L^?1 for SPE. Water samples from the Johannesburg area, South Africa, were analysed using both extraction methods and the results were in good agreement. The relative standard deviations were less than 12 % for both methods. In this comparison, SPE was found to give high concentration enrichment factors and recovery, whereas faster and cheaper analyses were achieved with HF-LPME. The concentration of PAHs found could be arranged in the following order: phenanthrene > acenaphthene > fluoranthene > naphthalene > pyrene.     

preconcentration and determination of amoxicillin and ceftriaxone in hospital sewage using vortex-assisted liquid-phase microextraction based on the solidification of the deep eutectic solvent followed by HPLC–UV

In the present study, a new method for extraction and preconcentration of amoxicillin and ceftriaxone was used in hospitalised sewage samples, called vortex-assisted liquid-phase microextraction based on the solidification of deep eutectic solvent. Samples were analysed by high-performance liquid chromatography–ultraviolet detection after preparation and extraction. In this method, the new deep eutectic solvent is used as the extraction solvent, which is obtained from the combination of 1-decyl-3-methylimidazolium chloride and n-butanoic acid. The important advantages of this novel extraction solvent include material stability, low density and good freezing point near room temperature. Under the optimum conditions, enrichment factors are in the range of 164–172. Repeatability and reproducibility of the method based on seven replicate measurements of 50.0 µg L^?1 of the target analytes in analysed samples were in the range of 2.1–3.5% and 3.8–5.2%, respectively. The limit of detections and linearity are in the range of 0.005–0.10 and 3–600 µg L^?1, respectively. The method was successfully applied for the determination of amoxicillin and ceftriaxone in the real sewage samples. The relative recoveries of sewage samples spiked with amoxicillin and ceftriaxone are 91–107%.