咔唑-9-乙基氯甲酸酯柱前衍生胺类化合物高效液相色谱分离

采用一种新的氯甲酸酯类荧光衍生试剂咔唑-9-乙基氯甲酸酯进行柱前衍生胺类化合物并通过荧光检测的方法进行高效液相色谱(HPLC)分析。衍生物的荧光激发和发射波长为λcr／λcrs=293/365nm。色谱柱：Hypersil BDS C18柱，柱温：35℃；流速：l mL/min；流动相A为水/乙腈(20／80，V／V)，流动相B为乙腈/水(95／5，V／V)。衍生试剂用量(mol)是胺类化合物总量的3～4倍时，衍生化产率最大且恒定。该方法具有检测灵敏度高，衍生化反应简单、快速、不受样品基质盐分的干扰，尤其适合天然生物样品，食品及饲料中的胺类化合物的分析。     

高效液相色谱法测定生姜中的6-姜酚

用C18色谱柱，以V(甲醇)：V(水)：V(冰乙酸)=35：64：1溶液作流动相，进样量5μL，在流速1．0mL／min下，可不经分离直接测定生姜中的6-姜酚。方法RSD小于1．00％，回收率97％～102％，相关系数0．9999。     

高效液相色谱-荧光检测法测定环境水中的苯胺和苯酚

建立了用高效液相色谱荧光检测法同时测定环境水中苯胺和苯酚的分析方法。色谱柱为EclipseXDB C8(4.6mmi.d.×150mm,5μm),流动相为甲醇 磷酸盐缓冲液(0.1mol/L磷酸二氢钾 0 1mol/L磷酸氢二钠,pH6.87)V(甲醇)∶V(磷酸盐缓冲液)=50∶50,流速1 0mL/min,柱温25℃,检测波长0minλex/λem=230/340nm(测定苯胺),3.5minλex/λem=215/300nm(测定苯酚)。测定苯胺的线性范围0.2～120ng,r=0.9999,检出限0.01ng;测定苯酚的线性范围0.4～500ng,r=0.9998,检出限0.02ng,回收率98.1%～101.2%。该方法已用于对环境水中苯胺和苯酚的测定。     

固相萃取富集-高效液相色谱法测定环境水中多菌灵和噻菌灵

建立了以固相萃取技术富集，高效液相色谱法进行分离和检测多菌灵和噻菌灵2种杀菌剂的方法。环境水中的多菌灵和噻菌灵用3M Empore 6mL C18 Cartridge进行固相萃取。以Hypersil ODS柱为分析柱，优化得到高效液相色谱分离条件：流动相为甲醇-水(50：50，V/V)；流速为0．7mL／min；柱温为55℃；在286nm波长下检测，检出限为0．05mg／L。本法操作简便，灵敏，回收率高。     

荧光试剂柱前衍生高效液相色谱-荧光检测生物检材中的氟乙酸钠

建立了以4-溴甲基-7-甲氧基香豆素(BrMMC)为柱前荧光衍生试剂,反相高效液相色谱荧光检测(HPLC-FLD)生物检材中氟乙酸钠的分析方法。采用Hewlett Packard RP-18色谱柱,以甲醇-水(60/40,V/V)为流动相,流速1.0 mL/min,柱温26℃,荧光检测:eλx=319 nm,eλm=390 nm,进样量2μL。结果表明:该法在氟乙酸钠含量为0.1~20μg/mL范围内与其峰面积呈良好的线性关系,线性相关系数为0.9996,检出限(S/N=3)为5×10-10mol/mL,相对标准偏差(RSD)小于4%。本法用于中毒死亡者的血液样品及其它检材的测定,效果良好。     

动物组织中金霉素残留测定的高效液相色谱柱后衍生反应研究

建立了动物组织中金霉素残留测定的高效液相色谱柱后衍生法,研究了镁离子和草酸体系对金霉素荧光强度的影响。结果表明,镁离子浓度和草酸浓度为1∶1.2时,金霉素的荧光强度最强。动物组织样品以5%高氯酸提取,正己烷脱脂,C18净化,Hy-persil ODS C18(250×4.6 mm,5μm)分离,流动相为甲醇∶0.05 mol/L草酸=80∶20(V/V),流速为0.7 mL/min,柱后0.05 mol/L乙酸镁衍生,流速为0.1 mL/min,紫外检测器和荧光检测器同时测定,提高了金霉素残留定量灵敏度。紫外检测波长365nm,荧光检测波长eλx=360 nm,eλm=520 nm。     

某些酚类的高温液相色谱行为

建立了高温液相色谱系统,在高温条件下,采用甲醇-水作为流动相,在Polymerx RP-1聚合物(PSDVB)色谱柱上考察了6种酚类样品的色谱行为.实验条件:温度40～160 ℃,流速0.2～5.5 mL/min,流动相中甲醇浓度范围40%～80%.考察了温度、流速和流动相组成对酚类样品的保留、分辨、柱效和系统压力的影响,探讨了酚类样品在聚合物柱上的热力学行为.温度升高2.35℃大约相当于流动相中甲醇浓度增加1%,可以通过改变色谱柱温度调节样品保留和改变选择性.柱温升高,降低了流动相的粘度,允许在高温条件下使用较高的流速实现快速分离.在160℃、V(甲醇):V(水)=40:60,为流动相和3 mL/min流速条件下,可于2.5 min内实现6种酚类的完全分离.     

高效液相色谱法测定珍菊降压片中氢氯噻嗪的含量

用高效液相色谱法测定珍菊降压片中氢氯噻嗪的含量。色谱柱为C18反相柱，流动相为甲醇-水溶液(甲醇与水的体积比为2：3)，流速为0．5mL／min，检测波长为277nm。氢氯噻嗪的质量浓度在18．24～42．56μg/mL内与对应的色谱峰面积呈线性关系，测定结果的相对标准偏差为0．78％，氢氯噻嗪的回收率为99．93％。     

卵类糖蛋白手性柱拆分钙离子拮抗剂尼卡地平对映体

研究了在卵类糖蛋白（OCCHI）手性柱上影响钙离子拮抗剂尼卡地平对映体拆分的主要因素，建立了尼卡地平对映体的拆分方法。氨丙基硅胶在0．2moL／L磷酸钠缓冲液（pH6．6）中与OGCHI反应，制备的固定相装填于10cm不锈钢柱中，用高效液相色谱法拆分尼卡地平对映体。优化的色谱条件为：0．05moL／L磷酸钠缓冲液（pH5．5）-甲醇（65：35），流速0．2mL／min，紫外检测波长236nm，柱温：25℃。在此条件下，尼卡地平对映体可得到良好分离。通过改变有机改性剂的种类和比例、流动相的pH值、缓冲溶液的浓度以及流速等色谱条件，确定了影响尼卡地平对映体拆分的主要因素。     

高效液相色谱法测定山生柳中酚苷类成分的含量

用高效液相色谱法测定山生柳中水杨苷、水杨酰水杨苷和木犀草素07－O－葡萄糖苷的含量，流动相为1．5％醋酸溶液－甲醇，Symmetry C18柱，柱温30℃，流速1．1mL/min，检测波长270nm，线性浓度范围分别为527．0－105．4um/mL,140-28.0ug/mL,81.0-16.2ug/mL，平均回收率是104．9％和103．6％，RSD分别为2．0％，0．3％和0．3％。     

Effects of Processing Parameters of 3D Bioprinting on the Cellular Activity of Bioinks

In this review, few established cell printing techniques along with their parameters that affect the cell viability during bioprinting are considered. 3D bioprinting is developed on the principle of additive manufacturing using biomaterial inks and bioinks. Different bioprinting methods impose few challenges on cell printing such as shear stress, mechanical impact, heat, laser radiation, etc., which eventually lead to cell death. These factors also cause alteration of cells phenotype, recoverable or irrecoverable damages to the cells. Such challenges are not addressed in detail in the literature and scientific reports. Hence, this review presents a detailed discussion of several cellular bioprinting methods and their process‐related impacts on cell viability, followed by probable mitigation techniques. Most of the printable bioinks encompass cells within hydrogel as scaffold material to avoid the direct exposure of the harsh printing environment on cells. However, the advantages of printing with scaffold‐free cellular aggregates over cell‐laden hydrogels have emerged very recently. Henceforth, optimal and favorable crosslinking mechanisms providing structural rigidity to the cell‐laden printed constructs with ideal cell differentiation and proliferation, are discussed for improved understanding of cell printing methods for the future of organ printing and transplantation.     

光子晶体太阳能电池研究进展

光子晶体具有光子禁带、“慢光子”效应等独特的光学性能,近年来被广泛用于太阳能电池中.光子晶体的引入,可调节光子在太阳能电池中的传播和分布.在电池中不同的位置引入光子晶体,能够提高或抑制太阳能电池的光电转化效率.因此充分了解光子晶体的光学特性,正确使用光子晶体是提高光电转化效率的关键.本文总结归纳不同类型光子晶体在硅太阳能电池及敏化型太阳能电池中的应用,并对其可能存在的问题进行了分析和评述.     

Control of endothelial cell adhesion to polymer surface by ion implantation

The bio‐compatibility of ion implanted polymers has been studied by means of in vitro attachment measurements of bovine aorta endothelial cells. The specimens used were polystyrene (PS), polyethylene (PE), polypropylene (PP) and expanded polytetrafluoroethylene (ePTFE). He⁺ and Ne⁺ ion implantation were performed at an energy of 150 keV with fluences between 1 × 10 ¹³ to 1 × 10 ¹⁷ ions/cm ² at room temperature. Wettability was estimated by means of a sessile drop method. The chemical and physical structures of ion implanted polymers were investigated by contact angle measurements, atomic force microscopy and X‐ray photoelectron spectroscopic analysis in relation to cell attachment behavior. The strength of cell attachment on ion implanted specimens at static and under flow conditions was also measured. Ion implanted PP and ePTFE were found to exhibit remarkably higher adhesion and spreading of endothelial cells than non‐implanted specimens. In contrast to these findings, ion implanted PS and PE only demonstrated a little improvement of cell adhesion in this assay. Copyright © 2001 John Wiley & Sons, Ltd.     

薄层电解池分析技术研究——串联式电池分析法的应用

本文介绍用双工作电极串联式的薄层电池,结合阳极溶出伏安法,用上游工作电极作富集-溶出电极;下游工作电极作收集电极,记录下游工作电极的收集电流。本法具有溶出法和薄层伏安法的优点,可消除电位扫描引入的电容电流,以及吸附电流、杂质电流的干扰,有效地提高了信噪比,提高了测定的灵敏度和分辨率。     

AFM研究蝙蝠葛碱对daudi细胞毒性的影响

利用原子力显微镜、CCK-8实验和流式细胞术研究了蝙蝠葛碱(dauricine)对B细胞淋巴瘤daudi细胞的细胞毒性。蝙蝠葛碱能显著抑制daudi细胞的增殖。CCK-8实验表明,细胞存活率与蝙蝠葛碱浓度存在时间依赖和剂量依赖关系。经10～50μmol/L的蝙蝠葛碱作用24 h后,daudi细胞存活率从(89.8±4.3)%降至(11.2±3.2)%;48 h后,存活率从(68.9±2.6)%降至(2.5±0.5)%。流式细胞术表明蝙蝠葛碱处理dau-di细胞24 h后,凋亡率从5.2%增至28.2%(60μmol/L)。AFM数据显示对照组细胞呈圆形,表面较光滑。经蝙蝠葛碱处理后,daudi细胞坍塌,超微结构显示细胞表面粗糙、凹凸不平。此外,经不同浓度蝙蝠葛碱作用的daudi细胞,其线粒体膜电位随着药物浓度的加大而降低。蝙蝠葛碱能显著抑制daudi细胞生长增殖。     

Lactase in Immobilized Cells of Watermelon

A cell suspension culture of Citrullus vulgaris Schrad cv. Samara was permeabilized by Tween 80 and immobilized by glutaraldehyde. The highest lactase activity was achieved at pH 4.3, the temperature optimum for cell suspension was at 50°C, while for the immobilized cells the optimum was at 58°C. The hydrolysis of substrate was linear for 3 h, reaching 60-67% conversion rate. The cells were characterized by high enzyme activity. The stability of the enzyme showed convenient physico-mechanical properties (physical protection from shear forces and easy separation of product from biocatalysts) in long-term storage.     

细胞表面壳化的研究进展

细胞表面壳化主要是通过物理、化学等技术方法对细胞表面进行修饰,形成完整均匀的有机、无机、金属纳米粒子或者复合壳层结构,从而使不能自身壳化的生物细胞表面形成保护壳甚至赋予细胞新的功能,使细胞具备多功能性。近年来,此技术在细胞存储、细胞运输、细胞传感器、细胞芯片以及细胞治疗等方面应用广泛,发展迅速。本文综合目前的研究现状,详细介绍了可进行细胞表面壳化的细胞类型、生物表面壳化的方法以及人造细胞外壳的工程技术在生物医学以及能源环境中的应用等。     

燃料电池汽车氢源选择的研究进展和预测

燃料电池汽车被认为是能源和交通领域的新方向之一,而目前氢源问题已成为其商业化的技术瓶颈。本文从国内外燃料电池汽车的发展现状出发,结合国外对燃料电池汽车氢源选择的评估和预测,及国内863计划“燃料电池汽车氢源基础设施工程前期研究”项目的研究结论,对我国燃料电池汽车的技术发展和商业化进程进行了预测。     

Studies of a photosynthetic photoelectrochemical cell using various electrodes

We have developed a photochemical cell using a combination of photosynthetic electron transport (photosystem I particles) and the photoreduction of a dye such as flavin mononucleotide (FMN) (6). The overall power conversion efficiency depends on the rate of charge transfer across the electrode surfaces in addition to the efficiency of the photosynthetic and photochemical reactions. For this reason, we studied the effect of varying the nature of the electrodes on the power developed. We found that reticulated vitreous carbon electrodes showed higher power conversion efficiencies than did nickel mesh, platinum, or SnO₂ glass. There are two reasons for this. First, the ratio of actual to apparent surface area is greater for RVC electrodes than for the others. Second, FMN and its photoproducts react better with carbon than platinum electrodes. Substituting RVC electrodes for platinum increased the power conversion efficiency from 1.0 to 3.9%. Platinizing platinum, nickel mesh, or brass electrodes also increased the power developed. However, the photopotential remained stable for several hours only for the platinized platinum electrodes.