不饱和聚酯／聚氨酯互穿网络聚合物的合成

以醋酸酐封端的不饱和聚酯（ＦＵＰＲ）与交联聚氨酯预聚物制备了具有互穿聚合物网络（ＩＰＮ）的不饱和聚酯／聚氨酯，通过红外，ＤＳＣ和扫描电镜等分析了ＦＵＰＲ／ＰＵＩＰＮ网络形成的动力学，微相分离行为及力学性能，结果表明，当ＦＵＰＲ／ＰＵ达到某一比值时，产生网络互穿效应，可改善聚氨酯的刚性，提高不饱和聚酯的抗冲性。     

紫外光固化聚二甲基硅氧烷脲撑氨基甲酸甲基丙烯酸酯的研究——Ⅱ亲水疏水共聚网络体系

本文以α、ω-二氨丙基封端的聚二甲基硅氧烷、甲苯二异氰酸酯、甲基两烯酸羟乙酯为原料,合成了甲基丙烯酸酯封端的聚二甲基硅氧烷聚氨酯。并以此作为反应性低聚物,以甲基丙烯酸羟乙酯为亲水性反应稀释剂,通过紫外光固化,合成了一系列聚硅氧烷含量不同的共聚网络。应用红外光谱、凝胶含量测定、热分析、动态力学性能、吸水性实验等方法,对它们的固化程度、亲水疏水性能进行了研究。结果表明:体系中存在着两相结构,增加稀释剂的含量,材料的吸水性增加。通过调节疏水性的聚二甲基硅氧烷和亲水性的甲基丙烯酸羟乙酯的含量可改变体系的亲水疏水平衡。     

RAFT聚合制备氟硅嵌段共聚物及结构性能

以三硫代酯封端的聚二甲基硅氧烷作为大分子链转移剂,通过可逆加成-断裂链转移聚合(RAFT)制备了一系列聚二甲基硅氧烷-b-聚甲基丙烯酸十二氟庚酯(PDMS-b-PDFHMA)二嵌段共聚物.利用凝胶渗透色谱(GPC)、傅里叶变换红外光谱(FT-IR)、氢核磁共振谱(1H-NMR)对该嵌段共聚物的组成、结构和分子量进行了表...     

MDI与TDI封端聚酯预聚物和扩链剂间反应速率的研究

用ＦＴＩＲ法系统地研究了不同硬段结构对聚酯型聚氨酯扩链反应动力学的影响，结果显示：不同类二异氰酸酯ＭＤＩ和ＴＤＩ形成的ＮＣＯ封端的聚酯预聚体与二元胺（ＭＯＣＡ）和三元醇（ＴＭＰ）的扩链反应均为二级反应，由ＭＤＩ形成ＮＣＯ封端的聚酯预聚体与胺或醇的扩链反应速度比ＴＤＩ类的要快，ＭＯＣＡ扩链比ＴＭＰ扩链反应活化能低，从基团反应活性不同体系扩链反速度的差别进行了讨论。     

聚丙烯酸酯/环氧树脂互穿网络聚合物的研究Ⅲ.橡胶态弹性模量和互穿缠结

采用一步法（Ｓｉｍｕｌｔａｎｅｏｕｓｌｙ）合成了双组分的聚丙烯酸酯／环氧树脂互穿网络聚合物（ＩＰＮｓ）．选择预溶胀方法制备了聚丙烯酸酯和环氧树脂两种组分网络．测定了各种组分比的ＩＰＮ和不同溶胀度下的组分网络的动态力学性能，从橡胶态弹性理论出发讨论了ＩＰＮ和预溶胀网络之间在橡胶态弹性模量上的关系，并据此指出互穿缠结增加了网络的有效“交联密度”，因此，它对ＩＰＮ的橡胶态弹性模量有较大的贡献．密度测量的结果也提供了另一方面的证据     

苯乙炔封端的BTDA系列酰亚胺预聚体的研究

合成了具有苯侧基的二胺单体1,4-双(4'-氨基苯氧基)-2-(苯基)苯(p-TPEQ), 并与3,3',4,4'-苯酮四羧酸二酐(BTDA)进行缩聚反应, 分别以4-苯乙炔苯酐(PEPA)和4-苯乙炔-1,8-萘二甲酸酐(PENA)作为封端剂, 合成了两个系列的苯乙炔封端的酰亚胺预聚体. DSC测试结果表明, 此类预聚体具有比PETI-5更宽的加工窗口; 利用所合成的预聚体制成了具有较高热分解温度热固性交联PI薄膜. 结果表明, PI预聚体加工性能良好, 其交联后具有优异的力学和热学性能; 同时PEPA封端的预聚体树脂具有比PENA封端的树脂更为优异的综合性能.     

多硫化物的液体聚合物

由聚硫橡胶化学协会N.J.Trenton所制成的多硫化物的液体聚合物(Liquid Polysulfide polymer以下简称液体聚硫橡胶)是一种由二氯二乙基缩甲醛(Dichlordithylformal亦可译作二氯烷烴类)和多硫化钠作用而得的低分子聚合物。它们便是人们久已熟知的以二氯乙烷和     

聚醋酸乙烯酯/聚丙烯酸甲酯互穿网络聚合物的研究——4.橡胶态模量和网络间的互穿缠结

用动态粘弹谱仪测定了分步法互穿网络聚合物,聚醋酸乙烯酯/聚丙烯酸甲酯(PVAc/PMA-IPN)的橡胶态模量。实验值与从方程E_R=φ_Ⅰ~1/3·E_(R,Ⅰ)~0+φ_(Ⅱ)E_(R,Ⅱ)~0所得理论值的比较,表明网络问有明显的互穿缠结,网络Ⅰ交联程度对其的影响大于网络Ⅱ。并结合实验结果对Binder-Frisch理论中,ΔS_(ent)∝N_(c,Ⅰ)~(-1)·N_(c,Ⅱ)~(-1/2)关系的合理性进行了讨论。     

硅氧烷表面改性聚醚酯聚酰亚胺的研究

通过两种方法。即将γ-氨丙基封端的聚二甲基硅氧烷和对氨基苯甲酸酯封端的聚(四亚甲基)醚与均苯四甲酸二酐共缩聚,和将两种预制的聚酰胺酸溶液共混,合成了一组硅氧烷改性的聚醚酯聚酰亚胺材料。ESCA能谱和表面水接触角测量研究材料的表面性质发现,硅氧烷在材料表面富集,对聚醚酯聚酰亚胺材料具有显著的表面改性作用,硅氧烷改性的聚醚酯聚酰亚胺,其热稳定性能和气体透过性能有一定程度的提高,但抗张强度和介电性能有所降低。     

基于脲醛原位聚合制备聚硫密封剂微胶囊

设计了以脲醛树脂为壁材,聚硫橡胶密封剂为囊芯的微胶囊.在弱酸性条件下,尿素和甲醛在经乳化分散后的聚硫橡胶密封剂微粒表面发生原位聚合,制备了颗粒均匀、形貌规整、分散性好的密封剂微胶囊.通过红外光谱和表面观察技术对微胶囊进行了表征,并且对微胶囊中密封剂含量进行测定.通过对不同物料和反应影响因素(乳化剂浓度、搅拌速度、反应温度和p H值等)进行了系统考察,获得了优化的微胶囊制备工艺条件.为进一步拓展聚硫橡胶密封剂预涂敷技术和工程化应用提供了有益参考.     

SYNTHESIS, CHARACTERIZATION AND PROPERTIES OF ORGANOCLAY-MODIFIED POLYSULFONE/EPOXY INTERPENETRATING POLYMER NETWORK NANOCOMPOSITES

Organoclay-modified hydroxylterminated polysulfone (PSF)/epoxy interpenetrating network nanocomposites (oM-PSF/EP nanocomposites) were prepared by adding organophilic montmorillonite (oMMT) to interpenetrating polymer networks (IPNs) of polysulfone and epoxy resin (PSF/EP) using diaminodiphenylmethane (DDM) as curing agent.The mechanical properties like tensile strength,tensile modulus,flexural strength,flexural modulus and impact properties of the nanocomposites were studied as per ASTM standards.Differ...     

聚氨酯环氧树脂乳液互穿聚合物网络结构与性能研究

分别以聚四氢呋喃(PTMG)和聚己二酸丁二酯(PBA)为聚氨酯(PU)软段,制备了高环氧树脂(EP)含量的PU/EP乳液互穿聚合物网络(LIPN).通过红外光谱,动态力学分析,原子力显微镜等研究了不同类型软段对LIPN结构与性能的影响.结果表明,LIPN结构已经形成,PU与EP间无化学键结合.以PBA为PU软段制备的LIPN中PU与EP相容性更好,分相程度相对低,互穿程度高,导致EP对PBA软段运动的限制作用较强,EP含量的变化对LIPN的玻璃化转变温度影响更大.研究样品的力学性能和溶剂溶胀性能发现,PBA为软段制备的LIPN均优于以PTMG为软段制备的LIPN,水溶胀率等有大幅减小,表现出明显的互穿协同效应.     

The Effect of Synthesis Method on Three-component IPNs Morphology and Property

Three-component IPNs were synthesized from polyurethane/poly (methyl acrylate aminoethyl methacrylate)/epoxy resin [PU/P(MADMA)/EP] by simultaneous synthesis interpenetrating polymer networks method(SINs) and sequential synthesis interpenetrating polymer networks method (STPNs). Comparing the effect of the two synthesis methods on the morphology and mechanical properties of three-component IPNs, it was found that the compatibility of three-component IPNs depends on the component ratios and interpenetrating formation , the different synthesis methods make the entanglement and interpenetrating between networks changed. The tensile strength of SIPNs is bigger than that of SINs, while the elongation at break of SINs is bigger than that of SIPNs. It is feasible to use stepwise staining method to observe the morphology change.     

Thermal,mechanical, and morphological properties of soybean oil-based polyurethane/epoxy resin interpenetrating polymer networks (IPNs)

A series of interpenetrating polymer networks (IPNs) based on epoxy (EP) resin and polyurethane (PU) prepolymer derived from soybean oil-based polyols with different mass ratios were synthesized. The structure, thermal properties, damping properties, tensile properties, and morphology of soybean oil-based PU/EP IPNs were characterized by Fourier-transform infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), universal test machine, and scanning electron microscopy (SEM). DSC and DMA results show that the glass transition temperature of the soybean oil-based PU/EP IPN decreases with the increase of PU prepolymer contents. Soybean oil-based PU/EP IPNs have better damping properties than that of the pure epoxy resin. The tensile strength and modulus of PU/EP IPNs decrease, while elongation at break increases with the increase of PU prepolymer contents. SEM observations reveal that phase separation appears in PU/EP IPNs with higher PU prepolymer contents.     

聚[丙烯酸甲酯-甲基丙烯酸2-(二甲氨基)乙酯]/环氧树脂IPN力学性能的研究

用同步法合成聚[丙烯酸甲酯-甲基丙烯酸2-(二甲氨基)乙酯]/环氧树脂(P(MA-DMA)/EP)互穿聚合物网络(IPN),对其力学性能进行了研究,结果表明,该体系IPN由于两网络间接枝导致相客性比较好,动态力学谱仅出现一个转变温度,当P(MA-DMA)/EP=20/80时,力学性能显示正协同效应,对环氧树脂的增韧效果最佳,不同组成比的IPNT_g实-T_g计与(d_实-d_计)差值成正比。     

Tribological performance and thermal behavior of epoxy resin nanocomposites containing polyurethane and organoclay

A series of epoxy resin nanocomposites modified by polyurethane and organically modified montmorillonite was prepared by effectively dispersing the organically modified montmorillonite in interpenetrating polymer networks (IPNs) of epoxy and polyurethane via the sequential polymeric technique and in situ polymerization. The tribological performance of the resultant EP/PU nanocomposites was investigated by a pin‐on‐disc tester, and the results showed that adding polyurethane and organically modified clay to the EP matrix had a synergistic effect on improving tribological performance of EP/PU nanocomposites. The morphologies of the worn surface were studied by scanning electron microscopy (SEM) observations, and the results indicated that the mechanism of improving tribological performance of EP/PU nanocomposites was different from that of pure EP or pure EP/PU IPNs. The thermal behavior of these nanocomposites was also investigated by thermogravimeric analysis (TGA), and the results indicated that adding organically modified clay to the matrix remedied the deterioration of the thermal degradation temperature of the interpenetrating networks. Copyright © 2008 John Wiley & Sons, Ltd.     

Controlled synthesis and evaluation of cyanate ester/epoxy copolymer system for high temperature molding compounds

Epoxy molding compounds (EMCs) have become an integral component for high power electronics to work under harsh environment nowadays. For high temperature operation, polymer networks with high glass transition temperature (T_g) are required to ensure device stability. In this work, high T_g polymers were designed via controlled incorporation of in situ formed and thermally stable triazine structures into epoxy matrix. Reactions involved in the copolymer system of cyanate ester and epoxy (CE/EP) were investigated. Increasing ratio of cyanate ester dramatically promoted T_g of the copolymer up to 275 °C with improved heat resistance. High temperature aging and moisture absorption tests revealed that hydrolysis of polycyanurate network and rearrangement of cyanurate occurred during aging, especially for copolymers with higher than 75% of cyanate ester. Based on thermal properties and aging performance, the composition of CE/EP system was optimized. The formulated bisphenol A cyanate ester and biphenyl epoxy copolymer system has great potential to be applied as high temperature encapsulation materials in electronic packaging. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1337–1345     

Morphology and dielectric properties of an epoxy network modified by end‐functionalized liquid polybutadiene

Epoxy resin networks modified with different functionalized liquid polybutadiene were characterized by scanning electron microscopy, atomic force microscopy (AFM), and dielectric thermal analysis techniques. Different morphologies were observed for these different systems, which were attributed to different interaction degrees between the components. Hydroxyl‐terminated polybutadiene (HTPB) and carboxyl‐ terminated polybutadiene (CTPB) resulted in epoxy networks with two‐phase morphology that differed in rubber particle size. The use of isocyanate‐terminated polybutadiene (NCOTPB) resulted in transparent thermoset material, whose rubber domains were in the nanoscale dimension, only detected by the AFM technique. The different morphological aspects in these epoxy systems also affected the dielectric properties. The epoxy–HTPB network exhibited two low temperature relaxation peaks corresponding to two different phases present in the system, whereas the epoxy–CTPB or epoxy–NCOTPB systems, whose rubber particles are well adhered to the epoxy matrix by chemical bonds, displayed only one single low temperature relaxation peak. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4053–4062, 2004     

耐高温改性环氧树脂粘接剂的制备及改性机理研究

采用新型固化体系和端羧基丁腈橡作为环氧树脂的改性剂，制备了一种具有耐高温、高强度、韧性好等特点的环氧树脂粘接材料。同 时对改性机理及增韧机理进行了初步探讨。