聚苯醚磺酸锂与聚乙二醇共混体系的结构与导电性研究

本文为提高聚苯醚磺酸锂(SPPOLi)的导电性能, 将聚乙二醇(PEG)与之共混,DSC分析发现SPPOLi的玻璃化转变温度随PEG的加入有所下降, 并且对于高磺化度的样品下降更为明显; X射线衍射表明, PEG可降低SPPOLi凝聚结构的有序程度;发现通过共混, 电导率有了较大提高, 并且仍保持了单离子的传导性。     

聚合物共混物脆韧转变性能研究─—形态参数对聚氯乙烯／丁腈橡胶共混物脆韧转变性能的影响

研究了非晶的聚氯乙烯（ＰＶＣ）／丁腈橡胶（ＮＢＲ）共混物脆韧转变特性，主要包括形态参数─—分散相粒径（ｄ）、体积分数（）、特别是分散相粒径分布（б）对其脆动转变性能的影响．结果表明，当ｄ＜临界值（ｄ）或＞临界值（）时，ＰＶＣ／ＮＢＲ产生脆韧转变．而且ｄＣ随。的增大而减小；随б的增大而增大。增大不利于增韧和脆韧转变的发生。也是影响聚合物共混物脆韧转变的重要形态参数，理论预示与实验结果很好相符．结果并给出ＰＶＣ／ＮＢＲ共混物的冲击韧性也是分散相粒间基体层厚度（Ｔ）的单参数函数．当Ｔ＞Ｔ时，共混物为脆性；当Ｔ≤Ｔ时，共混物韧性剧增成为超韧合金．虽然，以分子链结构参数分类，ＰＶＣ介于准韧性和脆性聚合物之间．结果证实，准韧性聚合物共混物脆韧转变的Ｔｃ判据仍然适用于ＰＶＣ／ＮＢＲ共混物．     

醋酸纤维素膜及其混合膜渗透气化性能的研究——稀溶液粘度斜率系数的依赖性

研究了醋酸纤维素（CA），乙烯－醋酸乙烯共聚物（EVA），聚乙烯醇缩丁醛（PVB）和聚醋酸乙烯酯（PVAc) 4种高聚物在不同溶剂中的稀溶液粘性行为。同时，从各相应的溶剂中制备了CA均一膜，CA－PVB和CA－PVAc共混膜以及CA－EVA复合膜，并测定了各种膜对甲醇（MeOH），甲基叔丁基醚（MTBE）混合物的渗透气化性能。结果表明，各种膜的渗透通量（J）与其稀溶液粘度斜率系数（b)成反比，即呈现随b值增大J值下降现象。     

POM／EVA共混物的研究

用力学测试、扫描电镜（ＳＥＭ）、热分析（ＤＳＣ）等手段研究了聚甲醛（ＰＯＭ）与乙烯－醋酸乙烯酯共聚物（ＥＶＡ）共混物（ＰＯＭ／ＥＶＡ）的力学性能及其微同形态；用聚甲醛与马来酸二丁酯（ＤＢＭ）的接枝物（ＰＯＭ－ｇ－ＤＢＭ）作相溶剂，能改变共的两相间的粘结力，从而提出了共混物的力学性能，ＳＥＭ观察表明接枝物的加入改变了ＰＯＭ／ＥＶＡ共混物的断裂方式，微观形态及结晶性能，对其热性能影响不大；通过改变ＰＯ     

EAA增容LLDPE／SAN共混物的形态及力学性能

采用SEM及力学性能测试等方法，研究了乙烯－丙烯酸共聚物（EAA）含量对其增容线性低密度聚乙烯（LLDPE）／苯乙烯－丙烯腈共聚物（SAN）共混物形态及性能的影响．发现少量的EAA可使共混物中SAN相的相尺寸减小，共混物模量、拉伸强度及断裂伸长率提高．当EAA的含量增加至11．7％时，它在共混物中两相界而的分布达到饱和，即增容剂饱和浓度Cs=11．7％；此时，共混物形态及性能的变化趋势出现明显转折．明显过量的EAA主要起增韧作用．EAA的增容机理为，它与LLDPE组分的非晶区可部分相容，同时又与SAN相存在着分子间特殊作用.     

界面粘结对聚氯乙烯/丁腈橡胶共混物脆韧转变的影响

应用丙烯腈（ＡＮ）含量不同的丁腈橡胶（ＮＢＲ）与聚氯乙烯（ＰＶＣ）共混，研究了界面粘结对ＰＶＣ／ＮＢＲ共混物脆韧转变的影响．结果表明：当基体层度Ｔ相等时，过强的界面粘结，使ＰＶＣ／ＮＢＲ共混物的冲击强度降低，并且其产生脆韧转变的临界基体层厚度Ｔｃ减小．界面粘结对于聚合物共混物的增韧行为具有直接的影响．损伤区分析给出：随着界面粘结强度增大，空洞化过程受阻，减弱能量的耗散，并且不利于诱导剪切屈服损伤的产生，因而不利于增韧；但是界面粘强度过小，意味着共混物的相容性太差，致使分散相粒径过大，也不利于增韧．所以对增韧来讲，共混物的界面粘结强度存在一个最佳范围．     

接枝共聚物氯化聚乙烯－苯乙烯对聚苯乙烯的共混改性

用氯化聚乙烯接枝苯乙烯共聚物（ＣＰＥ－ｇ－Ｓｔ）和氯比聚乙烯（ＣＰＥ）对聚苯乙烯（ＰＳ）进行共混改性．当ＣＰＥ含量为２５％时，用ＣＰＥ－ｇ－Ｓｔ改性的共混物的冲击强度为１８．５ｋＪ·ｍ￣（－２），是用ＣＰＥ改性的共混物冲击强度的２．１倍；其拉伸强度不低于３４ＭＰａ．     

用苯乙烯-丙烯腈无规共聚物作增容剂改善聚碳酸酯/聚甲基丙烯酸甲酯相容性的研究

对聚碳酸酯（ＰＣ）／苯乙烯 丙烯腈无规共聚物（ＰＳＡＮ）／聚甲基丙烯酸甲酯（ＰＭＭＡ）三元共混物，运用平均场理论，通过二元链段相互作用参数χｉｊ计算了其中三个二元对共混组成的相互作用参数χｂｌｅｎｄ，并计算了三元共混体系的ｓｐｉｎｏｄａｌ曲线．由此预测了三元共混物相容的条件，讨论了ＰＳＡＮ组成，各聚合物分子量对体系相容性的影响，并进行了实验验证．结果表明通过适当控制共聚组成和分子量，ＰＳＡＮ可以作为ＰＣ和ＰＭＭＡ共混物的增容剂，并可以通过仅改变ＰＳＡＮ在共混物中的比例来改善体系的相容性，直至得到完全均相的三元共混物．     

弹性体型聚氨酯和聚碳酸酯共混物的形态结构

用ＤＳＣ、ＷＡＸＤ和ＳＡＸＳ研究了溶液共混的弹性体型聚氨酯（ＰＵ）／聚碳酸酯（ＰＣ）共混物的结构。结果表明，ＰＵ／ＰＣ为部分相容体系；共混过程中，溶剂ＤＭＦ的诱导作用使ＰＣ形成结晶，其长周期与ＰＵ硬段形成微相的长周期相近     

侧链液晶离聚物对PA1010/PP共混体系的增容作用

将聚酰胺（PA1010）、聚丙烯（PP）和热致型侧链液晶离聚物（SLCI）进行熔融共混，采用FTIR，SEM，DSC，WAXD研究测定了共混物中的相互作用，用形态结构，热行为和结晶行为，系统地研究了SLCI对PA101／PP共混物的增容作用。结果表明，SLCI有效地改善了PA1010／PP共混物的形态结构，增强了PA1010与PP链间的相互作用，使PA1010／PP熔点升高，结晶度提高。     

Immobilization of Invertase in a Novel Proton Conducting Poly(vinylphosphonic acid) – poly(1-vinylimidazole) Network

A novel proton conducting polymer blend was prepared by mixing poly(vinylphosphonic acid) (PVPA) with poly(1-vinylimidazole) (PVI) at various stoichiometric ratios via changing molar ratio of monomer repeating unit to achieve the highest protonation. The polymer network having the most suitable stoichiometric ratio for substantial proton conductivity was prepared and characterized by FT-IR spectroscopy and proton conductivity measurements. The network was used for immobilization of invertase and some important kinetic parameters such as the maximum reaction rate (V_max) and Michaelis-Menten constant (K_m) were investigated for the immobilized invertase. Additionally, optimum temperature and pH were determined to acquire the best conditions for the highest enzyme activity. Operational stability of the entrapped enzyme was also examined. The results reveal that the most stable and highly proton conducting polymer network may play a pioneer role in the biosensors applications as given by FT-IR, elemental analysis, impedance spectroscopy and storage stability experiments.     

溴蒸气掺杂聚苯乙炔的导电机理

通过溴蒸气的吸附, 聚苯乙炔(PPA)的电导率比吸溴前提高近12个数量级. 采用固体紫外光谱、X光电子能谱研究了溴与PPA之间的p-π共轭效应, 探讨了掺溴PPA的导电机理. 研究表明, PPA掺溴产生了溴负离子和电子转移复合物, 促使导电率提高. 实验证明压力作用的增大有利于增强溴与PPA之间的共轭作用, 温度升高导致掺溴PPA中p-π共轭结构减少, 导致电导率降低.     

Gel processing of electrically conductive blends of poly(3-octylthiophene) and ultrahigh molecular weight polyethylene

The mechanical and electrical properties of solution-processed [or gel-spun] blends of poly(3-octylthiophene) and ultrahigh molecular weight polyethylene are discussed. Tensile drawing at elevated temperatures of the phase-separated blends resulted in significant improvements of the mechanical properties, in comparison with those of the neat conducting polymer, with values of the Young's modulus reaching > 40 GPa and tensile strengths in excess of 2 GPa. Doping of the undrawn polyblend fibers with iodine vapor or FeCl₃ resulted in materials of useful levels of electrical conductivity covering the full range of 10^?15 to 10 S/cm. A distinct percolation threshold for electrical conductivity was not observed, even at poly(3-octylthiophene) concentrations as low as 0.5 w/w %; the electrical conductivity of the latter blend, after doping with iodine vapor, was 8 × 10^?8 S/cm.     

聚3-辛基噻吩/MWNTs复合材料的导电性能研究

采用在氯仿溶液中超声共混, 制备聚3-辛基噻吩(P3OT)和多壁碳纳米管(MWNTs)复合材料. 当MWNTs掺杂量为3%时复合材料的电导率为1.43 S•m－1, 达到纯MWNTs的电导率水平. 用FTIR光谱, TG, UV-Vis光谱, XPS和FESEM进行研究分析, 认为MWNTs的离域电子与P3OT主链上的π电子之间形成π-π共轭, 增加了P3OT主链的有效共轭度, 被掺杂的P3OT具有很高的电导率, 提高了复合材料的导电性能. MWNTs与被掺杂的P3OT组成相对独立的导体单元, 对复合材料的导电网络形成起着主要作用.     

The oxidative polymerization of p‐phenylenediamine with silver nitrate: Toward highly conducting micro/nanostructured silver/conjugated polymer composites

The oxidative polymerization of p‐phenylenediamine with silver nitrate by using various oxidant/monomer mole ratios in aqueous solutions of both acetic and nitric acid was studied experimentally and computationally. The produced micro/nanostructured conducting poly(p‐phenylenediamine)–silver composites, reaching the conductivities >10⁴ S/cm, were characterized by conductivity and density measurements, gel permeation chromatography, transmission electron microscopy, UV–visible, FTIR, and Raman spectroscopies. The highest conductivity was 31,700 S/cm for poly(p‐phenylenediamine) base–silver (81.4 wt % Ag). The unexpected increase of conductivity after deprotonation of polymer component is discussed on the basis of interfacial electrical barriers and their removal. Theoretical study of the mechanism of p‐phenylenediamine oxidation has been based on the AM1 semi‐empirical quantum chemical computations of the heat of formation of the reaction intermediates, taking into account the influence of pH and solvation effects. Quantum chemical predictions of molecular structure of poly(p‐phenylenediamine) were correlated with spectroscopic findings. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Electrical conductivity,photoconductivity, and optical properties of poly(1,4‐diaminoanthraquinone) organic semiconductor for optoelectronic applications

The electrical conductivity and optical properties of the poly(1,4‐diaminoanthraquinone) [poly(1,4‐DAAQ)] have been investigated. The electrical conductivity of the polymer increases with temperature and room temperature conductivity was found to be 2.68 10^?5 S cm^?1. The optical band gap of the polymer is 1.87 eV due to the direct optical transitions. The photoconductivity of the polymer is higher than that of dark conductivity. When the light is switched on, the resistance decreases abruptly and when it is switched off, the resistance increases. This confirms that the polymer is a photoconductive material. The obtained results indicate that the poly(1,4‐DAAQ) is a photoconducting organic semiconductor with photovoltaic and dark current properties. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of thermal history on the ionic conductivity of block copolymer electrolytes

We have studied the effect of thermal history on ionic conductivity of block copolymer electrolytes. Previous work on block copolymer electrolytes composed of polystyrene‐b‐poly(ethylene oxide) (SEO) and lithium bis(trifluoromethanesulfone) imide (LiTFSI) salt was restricted to lamellar morphologies. This study addresses both cylindrical and lamellar morphologies. The conductivity of low molecular weight samples decreases after they are annealed. In contrast, the conductivity of high molecular weight samples is generally unaffected by annealing. These results are explained in the context of connectivity and composition of the conducting phase. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2013 , 51, 927–934     

SINGLE-ION CONDUCTIVITY IN POLY (LITHIUM PROPIONATE METHYL SILOXANE)

Poly(lithium propionate methyl siloxane )as a single-ion carrier source was synthesized. The crosslinked film showed lower lithium ionic conductivity at room temperature (about 10~(-10) S/cm). However,the lithium ionic conductivity was obviously increased by blending with high polar polymers such as polyethylene oxide, poly (methylsiloxane - co- ethylene oxide) and poly (methylsiloxane- g- ethylene oxide). In the blend system a high conductivity of 10~(-7)-10~(-5) Scm~(-1) at room temperature was obtained and the single-ion conductivity was deeply influenced by the content of the poly (lithium propionate methyl siioxane). The dc ionic conductivity of the flexible crosslinked films is more stable over time.     

SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30wt%)、SPEEK/SPES-C(30wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20wt%)共混膜电导率超过Nafion115膜;温度大于110℃时,SPEEK/SPES-C(30wt%)共混膜电导率与Nafion115膜相当,达到0.11S.cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.     

聚丙烯酸/聚丙烯酰胺水溶液复合特性的研究

通过酸度、电导率、粘度、接触角的测定,研究了聚丙烯酸 (PAA) /聚丙烯酰胺 (PAM) 水溶液复合物及复合物膜的结构和性能。结果表明,酸度、温度、浓度和复合比影响PAA/PAM的复合水溶液中大分子链的构象和流体力学体积,适度的氢键作用可以形成均相的复合溶液。经过热处理和未经热处理的聚合物膜表现出了不同的亲水性能。