Differential scanning calorimetry (DSC) in multiple W/O/W emulsions

Multiple water-in-oil-in-water (W/O/W) emulsions offer a huge potential as encapsulation systems in different food, cosmetic, and pharmaceutical applications. Because of their complex structure, however, it is difficult to characterize these systems. Typical measurement techniques to determine the size and stability of the inner water droplets encapsulated in the oil droplets show limitations and inaccuracies. Determining the total amount of water in the inner droplets is most often done by indirect methods to date. We describe an analytical method based on differential scanning calorimetry (DSC) for characterizing the total amount of encapsulated water droplets and their stability in W/O/W multiple emulsions. It uses the possibility to directly determine the latent heat of freezing of water droplets of the same size and composition as in the multiple emulsions. The amount of water in the inner droplets of a W/O/W emulsion can thus be calculated very accurately. It is shown that this method enables furthermore detecting multi-modalities in the size distribution of inner water droplets in W/O/W emulsions. Changes in droplet size distribution of the inner droplets occurring during the second emulsification step of processing or during storage can be detected. DSC thus offers a powerful tool to characterize the structure of multiple W/O/W emulsions.     

Influence of composition on the encapsulation properties of P/O/W multiple emulsions for Vitamin C

Abstract

The aim of this work was to study the encapsulation properties of polyols-in-oil-in-water (P/O/W) multiple emulsions for Vitamin C (Vc). The influence of formulation factors, including the concentration of lipophilic emulsifier, hydrophilic emulsifier, salt and glycerol had been investigated. The results indicated that the encapsulation stability could be improved by increasing the lipophilic emulsifier concentration which could strengthen the interfacial film. In contrast, the excess of hydrophilic emulsifier destabilized the emulsion. The presence of glycerol in the outer aqueous phase accelerated the phase transfer, thus reduced the encapsulation rate. The addition of salt in inner polyols phase had little effect on encapsulation rate while markedly affected the morphology and stability of this system. P/O/W multiple emulsions showed better encapsulation stability than the W/O/W multiple emulsions as the former’s encapsulation rate could remain more than 75% after 2?weeks while the latter only remained less than 60%. Meanwhile, the P/O/W emulsions exhibited higher storage modulus (G’), bigger loss modulus (G’’) and broaden linear viscoelastic regions than W/O/W emulsions.     

W/O/W多重乳液中水传递的控制

建立了简化的W/O/W(水/油/水)多重乳液乳珠模型——统计平均半径模型, 预测出当W/O/W多重乳液内水相水滴之间以及内外水相之间均达到水传递平衡时的内外水相中盐的浓度, 从而实现对水传递的控制, 以维持W/O/W多重乳液的稳定. 按理论预测制备出了不同稳定态的W/O/W多重乳液, 利用差分扫描量热仪(DSC)检测了多重乳液中水的传递过程, 确定体系在实验状态下的稳定程度, 实验结果与理论预测基本吻合.     

Effects of compositions on the stability of polyols-in-oil-in-water (P/O/W) multiple emulsions

Polyols-in-oil-in-water (P/O/W) multiple emulsions were successfully prepared by using polyols as inner aqueous phase to avoid instabilities caused by water. The influence of polyols, oils and emulsifiers on the morphology and stability of P/O/W multiple emulsions were studied and the stability mechanisms of this new kind of multiple emulsions were also explored. Glycerol that has the worst solubility in oil phase contributed to the formation of stable inner droplets which agree with the Ostwald Ripening theory. Mineral oil worked well with the system proving that oils possessing similar solubility parameters with the hydrophobic group of emulsifiers benefited for system stability. Several typical surfactants had been investigated in this article, and it turned out that emulsifiers Cetyl PEG/PPG-10/1 Dimethicone and the block copolymer Poloxamer 407 were suitable for the P/O/W system. The stability of the system affected by different compositions was evaluated based on microscopic observation and rheological measurements. The novel multiple emulsions will provide enlightening recommendations for future investigations and applications in cosmetic, food and pharmaceuticals, including drug delivery and the encapsulation of hydrophilic actives and actives that are soluble in polyols.     

Fat crystals: A tool to inhibit molecular transport in W/O/W double emulsions

Water-in-oil-in-water (W/O/W) double emulsions are a promising technology for encapsulation applications of water soluble compounds with respect to functional food systems. Yet molecular transport through the oil phase is a well-known problem for liquid oil-based double emulsions. The influence of network crystallization in the oil phase of W/O/W globules was evaluated by NMR and laser light scattering experiments on both a liquid oil-based double emulsion and a solid fat-based double emulsion. Water transport was assessed by low-resolution NMR diffusometry and by an osmotically induced swelling or shrinking experiment, whereas manganese ion permeation was followed by means of T₂-relaxometry. The solid fat-based W/O/W globules contained a crystal network with about 80% solid fat. This W/O/W emulsion showed a reduced molecular water exchange and a slower manganese ion influx in the considered time frame, whereas its globule size remained stable under the applied osmotic gradients. The reduced permeability of the oil phase is assumed to be caused by the increased tortuosity of the diffusive path imposed by the crystal network. This solid network also provided mechanical strength to the W/O/W globules to counteract the applied osmotic forces.     

Effect of Emulsifier Type on the Characterization of O/W Emulsions Using a Spectroscopy Technique

The droplet size distribution (DSD) of emulsions is the result of two competitive effects that take place during emulsification process, i.e., drop breakup and drop coalescence, and it is influenced by the formulation and composition variables, i.e., nature and amount of emulsifier, mixing characteristics, and emulsion preparation, all of which affect the emulsion stability. The aim of this study is to characterize oil-in-water (O/W) emulsions (droplet size and stability) in terms of surfactant concentration and surfactant composition (sodium dodecyl benzene sulphonate (SDBS)/Tween 80 mixture). Ultraviolet-visible (UV-vis) transmission spectroscopy has been applied to obtain droplet size and stability of the emulsions and the verification of emulsion stability with the relative cleared volume technique (time required for a certain amount of emulsion to separate as a cleared phase). It is demonstrated that the DSD of the emulsions is a function of the oil concentration and the surfactant composition with higher stability for emulsions prepared with higher SDBS ratio and lower relative cleared volume with the time. Results also show that smaller oil droplets are generated with increasing Tween 80 ratio and emulsifier concentration.     

Multiple emulsions for food use

Numerous investigations were done to describe the effects of different food-grade components (e.g. lipid phases, emulsifiers, electrolytes, biopolymers, sugars) on the stability of multiple emulsions (type W/O/W and O/W/O). In addition to the emulsion composition, the stability of such systems also depends heavily on the emulsion matrix, influenced by the dispersing methods used. This review highlights recently published results of research done in the preparation of such dispersed systems and in the manipulation of their emulsion stability as well as encapsulation behaviour.     

The effects of emulsifier type,phase ratio,and homogenization methods on stability of the double emulsion

The double emulsion technology has a potential effect on the development of diversity and quality of functional foods by means of decreasing oil or salt concentration, encapsulating and controlling release of valuable components. In this study, it was aimed to formulate stable double emulsions to be used in food systems. W1/O ratios of primary emulsions, stabilized by polyglycerol polyricinoleate (PGPR), were designed as 2:8 and 4:6, and (W1/O)/W2 ratios of the double emulsions were used as 2:8 and 4:6. W/O/W phase ratios, homogenization methods applied to primary emulsion (high-speed homogenization, ultrasonic homogenization), and emulsifier types used in W2 phase [sodium caseinate (SC), xanthan gum, lecithin-whey protein concentrate] were used as independent variables. Particle size and distributions, stability, encapsulation efficiency (EE), rheological properties, long-term stability, and morphological properties of the double emulsions were investigated.

The double emulsions prepared with SC and (W1/O)/W2 ratio of 4:6, were found to have the higher stability values, higher apparent viscosity, and lower particle size. High-speed homogenization applied to primary emulsion reduced particle size of the double emulsion and increased apparent viscosity, but did not affect stability and EE of the double emulsions, significantly.     

Stability and rheology of three types of W/O/W multiple emulsions emulsified with lecithin

Three types of multiple emulsions were prepared with lecithin. The morphology, stability, and rheological properties of the three types of W/O/W multiple emulsions were evaluated. The formulation factors, including salts and aliphatic alcohol, were further examined. The three types of multiple emulsions were formed by different emulsifiers. An excellent multiple emulsion occurred with 2?wt% lecithin concentration, stabilized by 0.05?wt% NaCl. All multiple emulsions showed shear-thinning behavior, i.e., the apparent viscosity decreased with the increase of the shear rate. With the high concentration of lecithin, the multiple emulsions exhibited the highest viscosity at low shear rate and had higher storage modulus (G′) and the loss modulus (G″). This study was conducted to reveal that different types of multiple emulsions can be formed with lecithin, and that the stability and rheological properties were different with different types of multiple emulsions.     

Relationship between rheological properties and one-step W/O/W multiple emulsion formation

Formation of a normal (not temporary) W/O/W multiple emulsion via the one-step method as a result of the simultaneous occurrence of catastrophic and transitional phase inversion processes has been recently reported. Critical features of this process include the emulsification temperature (corresponding to the ultralow surface tension point), the use of a specific nonionic surfactant blend and the surfactant blend/oil phase ratio, and the addition of the surfactant blend to the oil phase. The purpose of this study was to investigate physicochemical properties in an effort to gain a mechanistic understanding of the formation of these emulsions. Bulk, surface, and interfacial rheological properties of adsorbed nonionic surfactant (CremophorRH40 and Span80) films were investigated under conditions known to affect W/O/W emulsion formation. Bulk viscosity results demonstrated that CremophorRH40 has a higher mobility in oil compared than in water, explaining the significance of the solvent phase. In addition, the bulk viscosity profile of aqueous solutions containing CremophorRH40 indicated a phase transition at around 78 ± 2 °C, which is in agreement with cubic phase formation in the Winsor III region. The similarity in the interfacial elasticity values of CremophorRH40 and Span80 indicated that canola oil has a major effect on surface activity, showing the significance of vegetable oil. The highest interfacial shear elasticity and viscosity were observed when both surfactants were added to the oil phase, indicating the importance of the microstructural arrangement. CremophorRH40/Span80 complexes tended to desorb from the solution/solution interface with increasing temperature, indicating surfactant phase formation as is theoretically predicted in the Winsor III region. Together these interfacial and bulk rheology data demonstrate that one-step W/O/W emulsions form as a result of the simultaneous occurrence of phase-transition processes in the Winsor III region and explain the critical formulation and processing parameters necessary to achieve the formation of these normal W/O/W emulsions.     

Water mass transfer in W/O emulsions

Water transportation through the oil phase in W/O emulsions and in W1/O/W2 systems (W/O emulsion in contact with water) was examined. Substance diffusion through interfaces led to interface instability and spontaneous emulsification which caused nanodispersion formation. The photomicrographs of Pt/C replicas of emulsions showed the presence in the continuous oil phase a lot of nanodispersion droplets with a diameter in the range 17-25 nm. Diffusion coefficient (D) of water calculated on the base of Lifshiz-Slezov-Wagner (LSW) equation was about 15 times lower than the coefficients of molecular diffusion. Since such emulsions were extremely unstable toward coalescence, the growth of water droplets took place through as Ostwald ripening as coalescence. In three-phase W1/O/W2 systems diffusion of water, Rhodamine C, and ethanol was studied. D calculated on the base of the equation of nonstationary diffusion were approximately 1000 times lower than molecular ones. It was assumed, that nanodispersion droplets were more likely water carriers in investigated W/O emulsions stabilized by sorbitan monooleate.     

A Three-Step Model for Submicron W/O Emulsion Formation in a Transitional-Phase Inversion Process

A three-step model of the transitional phase inversion (TPI) process for the formation of water-in-oil (W/O) emulsions is presented. Three types of emulsions exist in an emulsification process at different oil–water ratios and hydrophilic–lipophilic balance (HLB). A stable W/O emulsion was obtained using Sorbitan oleate (Span 80) and polyoxyethylenesorbitan monooleate (Tween 80) with a specified HLB and oil volume fraction. Oil was added into water, which contained the water-soluble surfactant, to dissolve the oil-soluble surfactant. This route allowed TPI to occur, and an interesting emulsification process was observed by varying the HLB, which corresponded to the change in the oil–water ratio. Two types of emulsions in the emulsification process were found: transition emulsion 1 (W/O/W high internal phase emulsion) and target emulsion 2 (W/O emulsion with low viscosity). This study describes the changes that occurred in the emulsification process.     

FORMATION AND APPLICATIONS OF MULTIPLE EMULSIONS

Multiple emulsions, especially water-in-oil-in-water (W/O/W) type systems, have potential applications for the formulation and processing of foods, drugs, cosmetics, etc, as each dispersed globule in this type of emulsions consists of liquid compartments separated from the same liquid suspending medium by a thin layer of another immiscible liquid components. This article reviews a series of fundamental works on the formation and dispersion state of multiple emulsion systems and integrates advances made in the area of colloid science so as to obtain further insights into the formulation of W/O/W emulsions. The contents are divided into three sections: methods for preparing multiple emulsions in view of the phase diagram of mixed components, dynamic aspects of oil layer in W/O/W emulsions, and stability of this type of emulsions.     

Interface composition of multiple emulsions: rheology as a probe

We have investigated the dynamic rheological properties of concentrated multiple emulsions to characterize their amphiphile composition at interfaces. Multiple emulsions (W1/O/W2) consist of water droplets (W1) dispersed into oil globules (O), which are redispersed in an external aqueous phase (W2). A small-molecule surfactant and an amphiphilic polymer were used to stabilize the inverse emulsion (W1 in oil globules) and the inverse emulsion (oil globules in W2), respectively. Rheological and interfacial tension measurements show that the polymeric surfactant adsorbed at the globule interface does not migrate to the droplet interfaces through the oil phase. This explains, at least partly, the stability improvement of multiple emulsions as polymeric surfactants are used instead of small-molecule surfactants.     

One-step formation of w/o/w multiple emulsions stabilized by single amphiphilic block copolymers

Multiple emulsions are complex polydispersed systems in which both oil-in-water (O/W) and water-in-oil (W/O) emulsion exists simultaneously. They are often prepared accroding to a two-step process and commonly stabilized using a combination of hydrophilic and hydrophobic surfactants. Recently, some reports have shown that multiple emulsions can also be produced through one-step method with simultaneous occurrence of catastrophic and transitional phase inversions. However, these reported multiple emulsions need surfactant blends and are usually described as transitory or temporary systems. Herein, we report a one-step phase inversion process to produce water-in-oil-in-water (W/O/W) multiple emulsions stabilized solely by a synthetic diblock copolymer. Unlike the use of small molecule surfactant combinations, block copolymer stabilized multiple emulsions are remarkably stable and show the ability to separately encapsulate both polar and nonpolar cargos. The importance of the conformation of the copolymer surfactant at the interfaces with regards to the stability of the multiple emulsions using the one-step method is discussed.     

Multiple emulsion stability: pressure balance and interfacial film strength

The objective of this study was to investigate the significance of inner and outer phase pressure, as well as interfacial film strength on W/O/W multiple emulsion stability using microscopy and long-term stability tests. It was observed that immediately upon applying a coverslip to samples the multiple droplets deformed and there was coalescence of the inner aqueous droplets. Under certain conditions (such as lipophilic surfactant concentration and internal phase osmotic pressure) the destabilized multiple emulsions formed unique metastable structures that had a "dimpled" appearance. The formation of these metastable structures correlated with the real-time instability of the W/O/W multiple emulsions investigated. Multiple emulsion stability also correlated with the interfacial film strength (measured by interfacial elasticity) of the hydrophobic surfactant at the mineral oil/external continuous aqueous phase interface. The formation of the metastable dimpled structures and the long-term stability of the multiple emulsions were dependent on the osmotic pressure of the inner droplets and the Laplace curvature pressure as described by the Walstra Equation (P. Walstra, "Encyclopedia of Emulsion Technology" (P. Becher, Ed.), Vol. 4. Dekker, New York, 1996). It appears that the effect of coverslip pressure on multiple emulsions may be useful as an accelerated stability testing method or for initial formulation screening.     

Rheological characterization of polysaccharide-surfactant matrices for cosmetic O/W emulsions

Rheometrical techniques can be profitably used for polysaccharide matrices in order to evaluate their suitability for the preparation of stable cosmetic O/W emulsions. In particular, the rheological properties of aqueous scleroglucan systems were investigated under continuous and oscillatory shear conditions in a polymer concentration range (0.2-1.2% w/w) embracing the sol/gel transition. The effects due to the addition of two different surfactants (up to 10% w/w) were examined at constant polymer concentration (0.4% w/w). The selected additives are a nonionic polymeric siliconic surfactant (dimethicone copolyol) and a cationic surfactant (tetradecyltrimethylammonium bromide), respectively. Polysaccharide-surfactant interactions leading to complex formation were detected also through rheology. The combined action of both nonionic and cationic surfactants in the polymer solution was examined at two different surfactant concentration levels (5 and 10% w/w), demonstrating the beneficial effects produced on the mechanical properties of the polymer matrix by the coexistence of both surfactants. Such beneficial effects are confirmed by the stability and rheology shown by the emulsions prepared. In this way, the results point out the good agreement between the rheology of the continuous phase and the final characteristics of the emulsion obtained.     

Preparation of a stable double emulsion (W1/O/W2): role of the interfacial films on the stability of the system

This paper presents new protocols enabling preparation of W1/O/W2 double emulsions: one, using soybean oil as the O phase, that yields edible emulsions with industrial applications, and a second that yields emulsions with a previously unattainable concentration 15% (w/w) of surfactants in the external phase (the 15% target was chosen to meet the typical industry standard). Preparation of a stable W1/O emulsion was found to be critical for the stability of the system as a whole. Of the various low HLB primary surfactants tested, only cethyl dimethicone copolyol (Abil EM90), A-B-A block copolymer (Arlacel P135), and polyglycerol ester of ricinoleic acid (Grinstead PGR-90) yielded a stable W/O emulsion. Investigation of the surface properties of those surfactants using the monolayer technique found two significant similarities: (1) stable, compressible, and reversibly expandable monolayers; and (2) high elasticity and surface potential. The high degree of elasticity of the interfacial film between W1 and O makes it highly resilient under stress; its failure to break contributes to the stability of the emulsion. The high surface potential values observed suggest that the surfactant molecules lie flat at the O/W interfaces. In particular, in the case of PGR-90, the hydroxyl (-OH) groups on the fatty acid chains serve as anchors at the O/W interfaces and are responsible for the high surface potential. The long-term stability of the double emulsion requires a balance between the Laplace and osmotic pressures (between W1 droplets in O and between W1 droplets and the external aqueous phase W2). The presence of a thickener in the outer phase is necessary in order to reach a viscosity ratio (preferably approximately 1) between the W1/O and W2 phases, allowing dispersion of the viscous primary emulsion into the W2 aqueous phase. The thickener, which also serves as a dispersant and consequently prevents phase separation due to its thixotropic properties, must be compatible with the surfactants. Finally, the interactions between the low and high HLB emulsifiers at the O/W2 interface should not destabilize the films. It was observed that such destructive interaction for the system could be prevented by the use of two high HLB surfactants in the outer aqueous phase: an amphoteric surfactant, Betaine, and an anionic surfactant, sodium lauryl ether sulfate. The combination of such pairs of surfactants was found to contribute to the films' stability.     

Application of the fractional factorial design in multiple W/O/W emulsions

In presented research, multiple W/O/W emulsions were developed by using experimental design method. A 24-1 fractional factorial design was performed by varying the following input parameters: primary polymeric emulsifier (PEG 30-dipolyhydroxystearate) concentration (0.8% and 2.4%), secondary polymeric emulsifier (Poloxamer 407) concentration (0.8% and 1.2%), electrolyte magnesium sulfate heptahydrate (0.08% and 0.4%) and electrolyte sodium chloride (0.08% and 0.4%). Multiple emulsions were prepared by a two-step emulsification process. Obtained emulsions were characterized with rheological measurements, conductivity and centrifugation tests. Factorial analysis revealed that the concentration of the primary emulsifier was the predominant factor influencing the phase separation, conductivity and maximal apparent viscosity. Additionally, electrolyte magnesium sulfate heptahydrate was more efficient in stabilizing these systems, compared to sodium chloride. The applied fractional factorial design method enabled determination of the optimal concentrations of the primary and secondary emulsifier, as well as the concentration of electrolytes, in order to obtain W/O/W emulsions with desired maximal apparent viscosities, low values of conductivity and without phase separation after centrifugation.