Au core-PtAu alloy shell nanowires for formic acid electrolysis

Inefficient electrocatalysts and high-power consumption are two thorny problems for electrochemical hydrogen(H2)production from acidic water electrolysis.Herein we report the one-pot precise synthesis of ultrafine Au core-Pt Au alloy shell nanowires(Au@PtxAu UFNWs).Among them,Au@Pt_0.077 Au UFNWs exhibit the best performance for formic acid oxidation reaction(FAOR)and hydrogen evolution reaction(HER),which only require applied potentials of 0.29 V and-22.6 m V to achieve a current density of 10 m A cm^-2,respectively.The corresponding formic acid electrolyzer realizes the electrochemical H2 production at a voltage of only 0.51 V with 10 m A cm^-2 current density.Density functional theory(DFT)calculations reveal that the Au-riched Pt Au alloy structure can facilitates the direct oxidation pathway of FAOR and consequently elevates the FAOR activity of Au@Pt_0.077 Au UFNWs.This work provides meaningful insights into the electrochemical H₂ production from both the construction of advanced bifunctional electrocatalysts and the replacement of OER.     

Layered Ag-graphene films synthesized by Gamma ray irradiation for stable lithium metal anodes in carbonate-based electrolytes

Lithium metal batteries are considered as high energy density battery systems with very promising prospects and have bee n widely studied.However,The uncon trollable plating/strippi ng behavior,infinite volume change and den drites formation of lithium metal anode restrict the applicati on.The unc on trolled n ucleati on of lithium caused by the non uniform multi-physical field distributions,can lead to the undesirable lithium deposition.Herein,a graphene composite uniformly loaded with Ag nano-particles(Ag NPs)is prepared through a facile Gamma ray irradiation method and assembled into self-supported film with layered structure(Ag-rGO film).Whe n such film is used as a lithium metal an ode host,the uncontrolled deposition is converted into a highly nucleation-induced process.On one hand,the Ag NPs distributed between the in terlayers of graphe ne can preferentially induce lithium nu cleati on and en able uniform deposition morphology of lithium between interlayers.On the other hand,the stable layered graphene structure can accommodate volume change,stabilize the interface between anode and electrolyte and inhibit dendrites formation.Therefore,the layered Ag-rGO film as anode host can reach a high Coulombic efficiency over 93.3% for 200 cycle(786 h)at a current density of 1 mA cm^-2 for 2 mAh cm^-2 in carbonate-based electrolyte.This work proposes a facile Gamma ray irradiation method to prepare metal/3D-skeleton structure as lithium anode host and demonstrates the potential to regulate the lithium metal deposition behaviors via manipulating the distribution of lithiophilic metal(e.g.Ag)in 3D frameworks.This may offer a practicable thinking for the subsequent design of the lithium metal anode.     

中国纤维素乙醇技术的研究进展

中国面临着严重的能源短缺和环境污染问题,中国政府正在局部几个省份内政策性鼓励燃料乙醇生产和使用.尽管当前主要是用玉米和谷物作为生产乙醇的原料,然而中国具有大量潜在的低成本的纤维素生物质原料,可以极大地扩大乙醇的产量,降低原料成本.近20年来,由于技术的革命性进步,已使得纤维素乙醇的生产成本从4美元/加仑以上,降低至约1.2-1.5美元/加仑.其中,每吨生物质约44美元.因此,目前乙醇掺汽油具有十分强的市场竞争力.已有几个公司正在建造首批商业纤维素乙醇工厂,虽然这些刚起步的小型设施在合理利用和管理上风险较小,但规模经济需要较大型工厂.尽管配送生物质原料的成本会随需求的增加而增加,但在乙醇生产基础上的生物精炼技术的发展,尤其是化工产品和动力的协同生产,将会使全过程的经济可行性大大提高.进一步深入的基础研究,将解决低成本下实现纤维素的完全利用,以确保在无政策性补贴的前提下,真正使纤维素乙醇成为具有市场竞争力的低成本纯液体燃料.     

Binary ligand strategy toward interweaved encapsulation-nanotubes structured electrocatalyst for proton exchange membrane fuel cell

Hierarchically porous architecture of ir on-nitroge n-carb on(Fe-N-C)for oxyge n reducti on reaction(ORR)is highly desired towards efficient mass transfer in the fuel cell device manner.Herein,we reported a binary ligand strategy to prepare zeolitic imidazolate frameworks(ZIFs)-derived precursors,wherein the addition of secondary ligand endows precursors with the capabilities to transform into porously interweaved encapsulation-nanotubes structured composites after calcination.The optimal catalyst,i.e.,termed as Fe₆-M/C-3,exhibits excellent durability with 88.8%current retention after 50,000 seconds in 0.1 M HClO₄solution by virtue of nanoparticles-encapsulation features,which is more positive than the benchmark commercial 20 wt%Pt/C catalyst.Moreover,a promising maximum power density of Fe₆-M/C-3 as cathode catalyst was also dem on strated in proton exchange membrane fuel cells(PEMFCs)measurements.Therefore,this binary ligand approach to the fabrication of hierarchically porous structures would also have significant implications for various other electrochemical reactions.     

Molten salt as ultrastrong polar solvent enables the most straightforward pyrolysis towards highly efficient and stable single-atom electrocatalyst

Currently,pyrolysis as the most widely used method still has some key issues not well resolved for synthesis of carbon-supported single-atom catalysts(C-SACs),e.g.,the sintering of metal atoms at high temperature as well as the high cost and complicated preparations of precursors.In this report,molten salts are demonstrated to be marvellous medium for preparation of C-SACs by pyrolysis of small molecular precursors(ionic liquid).The ultrastrong polarity on one hand establishes robust interaction with precursor and enables better carbonization,resulting in largely enhanced yield.On the other hand,the aggregation of metal atoms is effectively refrained while no nanoparticle or cluster is formed.By this strategy,a C-SAC with atomically dispersed Fe-N₄ sites and a high specific area over 2000 m² g^-1 is obtained,which illustrates high ORR activity in both acid and alkaline media.Moreover,this SAC exhibits superior methanol tolerance and stability after acid soaking at 85℃ for 48 h.It is believed that the molten-salts-assisted pyrolysis can be developed into a routine strategy as it not only can largely simply the synthesis of C-SACs,but also can be extended to prepare other types of SACs.     

镧对Mg-Si合金中Mg2Si相变质的影响

研究了Mg-5Si合金中La的添加对初生Mg2Si相变质的影响。结果表明,适量的La能够有效地变质初生Mg2Si相。基于本文的研究,在添加约0.5%La时,获得了最佳的变质效果,此时,初生Mg2Si相的尺寸减小到25μm以下,其形态从粗大的树枝形状变为多面体形状。然而,当La增加到0.8%或者更高时,初生Mg2Si相又生长为粗大的树枝形态。而且,在凝固过程中发现形成了一些LaSi2化合物,这些化合物的数量随着La的增加而呈现逐渐增加的趋势。     

电感耦合等离子体质谱法测定天然水体中19种元素

建立STD/KED模式-电感耦合等离子体质谱（ICP-MS）法同时测定天然水体中铍、硼、钛、钒、铬、锰、钴、镍、铜、锌、钼、镉、锑、钡、铊、铅、铁、砷和硒19种元素的分析方法。仪器调谐校准后,样品在线加入锂、钪、铑、铋校准溶液校正,以标准曲线内标法定量分析。标准曲线相关系数均大于0.999,样品加标回收率为92.6%～103.6%,质控样品测定值相对标准偏差为0.20%～2.6%(n=6),方法检出限为0.01～0.70μg/L。该方法灵敏度高,操作简便,节省人力,能满足天然水体中19种元素的同时检测需要。     

电解质-非电解质混合溶液活度系数的关联及溶解的推算 II:NH3-NaCl-Na2SO4-H2O体系的液固平衡热力学

由于在研究的体系中, Na2SO4是非对称电解质, 且能生成水合盐, 故推导了由非对称型电解质与非电解质所构成的混合溶液的各组分的活度系数关联通式, 并在此基础上讨论了水合盐液固平衡的计算方法.     

黄花棘豆化学成分的研究II:两种三萜皂苷的结构

从黄花棘豆的总皂苷中分离出两个新皂苷1和2.经光谱分析及化学方法确证,1为3-O-[α-L-鼠李吡喃糖基(1→2)-β-D-葡萄吡喃糖基(1→4)-β-D-葡萄吡喃糖醛酸基]-黄豆醇B;2为3-O-[α-L-鼠李吡喃糖基(1→2)-α-L-阿拉伯吡喃糖基(1→4)-β-D-葡萄吡喃糖醛酸基]-黄豆醇B.     

二氧化钛纳米管的研究进展

二氧化钛纳米管由于其新奇的光电、催化、气敏等性能引起了广泛的关注,在太阳能电池、光催化、环境净化、气体传感器等领域有潜在的应用价值.本文概述了近年来在制备方法、反应机理和组成、晶型和形貌及掺杂和应用方面的进展,并讨论了今后可能的研究发展方向.     

MoS2/GQDs催化剂的制备及微生物电解池的产氢性能研究

通过水热法合成了一系列MoS₂/GQDs复合材料,并制成碳基复合电极。利用电化学测试手段挑选出最佳电极后用于微生物电解池（MEC）阴极的产氢性能研究。实验结果显示： Na₂MoO₄、半胱氨酸和GQDs的最佳原料配比为375:600:1,制备出的MoS₂/GQDs呈现明显的爆米花样纳米片结构,片层厚度在10 nm左右,当碳纸负载量为1.5 mg·cm^-2时,MoS₂/GQDs碳纸电极的析氢催化能力最佳。在MEC产氢实验中,MoS₂/GQDs阴极MEC的产气量、氢气产率、库仑效率、整体氢气回收率、阴极氢气回收率、电能回收率和整体能量回收率分别为51.15±3.15 mL·cycle^-1、0.401±0.032 m³H₂·m³d^-1、91.16±0.054%、66.64±5.39%、72.44±2.60%、217.26±7.42%和77.37±1.50%,均略高于Pt/C阴极MEC或与之媲美。另外,MoS₂/GQDs具有良好的长期稳定性,且价格便宜,有利于实际应用。     

金属相1T´ MoS2增强类石墨相C3N4的可见光催化性能

通过煅烧和静电自组装的方法制备了1T′ MoS₂超薄纳米片和类石墨烯相氮化碳(g-C₃N₄)纳米片的复合材料. 该材料在光催化实验中展现出6.24 μmol?g^?1?h^?1的产氢速率, 优于贵金属铂修饰的g-C₃N₄纳米片的性能(4.64 μmol?g^?1?h^?1). 此外, 该复合材料在光催化降解有机染料甲基橙的实验中表现出0.19 min^?1的催化速率, 而纯g-C₃N₄纳米片只有0.053 min^?1的催化速率. 材料光催化性能的提升可归结于1T′MoS₂ 和g-C₃N₄之间的协同效应, 包括光吸收的增强以及因1T′MoS₂优异电子导电性而得到的高效电荷分离.     

A new efficient visible-light-driven photocatalyst Na0.5Bi1.5VMoO8 for oxygen evolution

A new visible-light-driven photocatalyst Na_0.5Bi_1.5VMoO₈ was developed by making a solid solution of BiVO₄ and (NaBi)_0.5MoO₄. The prepared powders were confirmed crystallizing in the tetragonal scheelite crystal structure by the XRD patterns and Raman spectra. Different from that of the tetragonal BiVO₄, Na_0.5Bi_1.5VMoO₈ showed a high activity for photocatalytic O₂ evolution under visible light irradiation, which is even better than that of monoclinic BiVO₄, a well-known efficient visible-light-driven photocatalyst. The mechanism of the improved activity of Na_0.5Bi_1.5VMoO₈ was discussed.     

MoS_2/TiO_2复合催化剂的制备及其在紫外光下的光催化制氢活性

为了研究复合光催化剂在光催化中的制氢效率,采用水热法制备了Mo S2纳米片,然后通过水热法在Mo S2纳米片上负载了TiO_2纳米颗粒,形成了Mo S2/TiO_2异质结复合催化剂。采用冷场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、紫外-可见吸收光谱(UV-Vis)、拉曼光谱(Raman),X射线光电子能谱(XPS)对材料的结构和光学性能表征并进行分析。通过光催化制氢测试对光催化剂进行评价,实验结果表明,在波长为365 nm的紫外光照射下,最高光催化制氢速率为1004μmol·h-1·g-1,对应的催化剂的Mo S2含量为30%,其催化速率远大于单一的Mo S2和TiO_2,表明Mo S2/TiO_2复合催化剂在紫外光照下能显著提高光催化产氢性能。基于Mo S2/TiO_2复合光催化剂优越的光催化产氢性能,本文对复合光催化剂的产氢机理做了研究和分析。     

单个MoS2纳米片氢析出催化特性研究

MoS₂作为高效的电催化氢析出(HER)催化剂已有大量文献报道. 实验和DFT计算结果都表明MoS₂的高氢析出活性来源于边缘,而其基面是催化惰性的。为了进一步验证此结论,本文利用巯基羧酸在恒电位下自组装单层修饰的纳/微米电极固定不同尺寸的单个纳米片状,对MoS₂氢析出催化活性与其尺寸的关系进行研究,发现纳米片状MoS₂具有较高的催化活性,同时较小尺寸的MoS₂氢析出活性更高,说明MoS₂的边缘的增多对其催化活性有巨大提升,即证明了边缘部分具有更高的氢析出催化活性.     

Study of the reactions of pyridinium poly(hydrogen fluoride) with some ternary oxides

The products of the reaction of pyridinium poly(hydrogen fluoride), PPHF, with KIO₃, Na₂SnO₃, NaBiO₃, K₂CrO₄, Na₂MoO₄ and Na₂WO₄ were KIO₂F₂; Na₂SnF₆; NaHF₂, BiF₃; K₃CrF₆, KHF₂, (PyH)₃CrF₆; NaHF₂, (PyH)₂MoO₂F₄·2NaHF₂; and (PyH)₂WO₂F₄·2NaHF₂, respectively, while KClO₃, KBrO₃ and KIO₄ react with complete decomposition to form KHF₂ as the fluorinated product. This differential reactivity and mode of reaction has been discussed in terms of the oxidation state of the central atom, the nature and strength of the bonds and the complex behaviour of the formed intermediate or fluorinated products that undergo complexation or solvation with pyridine and/or hydrogen fluoride.     

ZnCuAl-LDH/Bi2MoO6纳米复合材料的构建及其可见光催化降解性能

In this study, pure Bi₂MoO₆ was synthesized via a solvothermal method. A ZnCuAl-layered double hydroxide (LDH)/Bi₂MoO₆ (denoted as LDH/Bi₂MoO₆) nanocomposite was synthesized via a steady-state co-precipitation route using Bi₂MoO₆ as the matric material. LDH was deposited on the surface of Bi₂MoO₆ with a close contact interface. The specific surface area of the resulting LDH/Bi₂MoO₆ composite increased up to 19.1 m²∙g⁻¹ owing to the stacking arrangement between LDH and the Bi₂MoO₆ nanosheets, resulting in the generation of a large number of reactive sites. In addition, the light absorption region of the LDH/Bi₂MoO₆ composite was larger than those of pure LDH and Bi₂MoO₆ because of the formation of a heterojunction structure and the possible quantum size effect. The photocatalytic performance of the as-prepared samples was evaluated by carrying out the degradation of rhodamine B (RhB) using them under visible light irradiation. Compared to pure LDH and Bi₂MoO₆, the LDH/Bi₂MoO₆ nanocomposite exhibited enhanced photocatalytic activity for the degradation of RhB. With an increase in the LDH content, the photocatalytic activity of the LDH/Bi₂MoO₆ composite first increased and then decreased. Although the addition of an optimum amount of LDH was beneficial for the generation of electron-hole pairs, excessive LDH on the surface of Bi₂MoO₆ decreased the visible light absorption ability of both the components, thus reducing photocatalytic activity of the composite. This indicates that an appropriate LDH:Bi₂MoO₆ molar ratio is necessary for obtaining LDH/Bi₂MoO₆ composites with excellent photocatalytic activity. Furthermore, the LDH/Bi₂MoO₆ composite showed high photocatalytic stability and reusability. The structure of the LDH/Bi₂MoO₆ composite remained almost unchanged even after four photodegradation cycles. The enhanced photocatalytic performance of the composite can be attributed to the combined effect of its heterojunction structure and high specific surface area, which are beneficial for effective separation of photogenerated charge carriers and the availability of a large number of active sites for photocatalysis. It was found that •OH and O₂^•− were the main reactive species, while e⁻ and h⁺ contributed little to the photodegradation process. The generation, transfer, and separation of photoinduced electrons and holes in the composites were investigated by transient photocurrent responses, electrochemical impedance spectroscopy Nyquist plots, and photoluminescence measurements. The results showed that the heterojunction structure of the composites played a key role in enhancing their photocatalytic activity. A possible photodegradation mechanism was proposed for the composite. This study will provide a facile approach for the preparation of LDH- and/or Bi₂MoO₆-based nanocomposites. The LDH/Bi₂MoO₆ nanocomposite prepared in this study showed huge potential to be used as a visible-light photocatalyst for degrading environmental pollutants.     

氧化石墨烯调控钼酸铋在可见光下选择性光催化降解环境水中的抗生素

以氧化石墨烯(GO)作为增强光催化剂活性的调节剂, 采用一步水热法制备钼酸铋/氧化石墨烯(Bi₂MoO₆/GO)异质结光催化剂, 其可见光响应拓展至570 nm, 带隙能降至2.56 eV. 当m_Bi2MoO6/m_GO=100∶1时, Bi₂MoO₆/GO(100∶1)光催化剂在可见光的辐射下, 对水溶液中四环素和喹诺酮类抗生素选择性的高效催化降解去除能力为Bi₂MoO₆的2.1倍. Bi₂MoO₆/GO(100∶1)光催化剂活性的提高依赖于范德华力作用下的二维Bi₂MoO₆纳米片-二维GO纳米片界面的紧密接触. 有效的界面接触改善了光生电子的转移和光生载流子的分离. 自由基清除实验结果表明, ?OH起主要作用. 结合高效液相色谱-质谱(HPLC-MS)法对降解产物的分析, 提出了不同光催化剂催化降解恩诺沙星具有相似的降解途径和降解产物.     

CoMo型耐硫变换催化剂不同硫化剂的器外预硫化研究

从多种硫化剂中筛选出(NH_4)_2S和Na_2S,分别采用不同的预硫化技术对工业级CoMo型耐硫变换催化剂进行器外预硫化,采用XRD、XPS和HRTEM等表征手段对催化剂的晶相结构、表面特性和微观形貌进行表征。(NH_4)_2S和Na2S作为预硫化剂对催化剂的晶相结构没有明显影响;用(NH_4)_2S进行预硫化时活性组分发生部分O-S交换,而用Na_2S进行预硫化时活性组分仍保持为氧化态,两种预硫化型催化剂在反应器内随着反应温度升高,硫化深度为S-Na_2SS-(NH_4)_2S常规器内预硫化;器内预硫化和(NH_4)_2S作为预硫化剂MoS_2片层结构堆叠层数集中在2-3层,而用Na_2S进行预硫化时MoS_2片层堆叠层数明显变多,集中在3-5层。采用微型固定床评价装置,选择285、350、450℃三个反应温度,催化剂的活性顺序为SNa_2SS-(NH_4)_2S常规器内预硫化。     

纳米片层二硫化钼负载PtCo双金属催化甲醇水相重整制氢

采用水热法合成了层数只有六层的纳米片层二硫化钼（MoS₂）,并进一步负载Pt和PtM双金属（M=Ru、Pd、Co和Ni）,用于催化甲醇水相重整制氢反应。结果表明,PtCo/MoS₂对于甲醇水相重整具有最优异的催化性能,在220℃下产氢转换频率（TOF）为37142 h^-1。氮气吸附-脱附等温线、透射电子显微镜（TEM）、程序升温还原（H₂-TPR）以及X射线光电子能谱（XPS）等表征结果表明,PtCo/MoS₂中金属还原程度高,且Pt与载体MoS₂形成了强电子相互作用,使缺电子的Pt有利于吸附活化甲醇,并进一步促进甲醇重整反应。