Indirect determination of ascorbic acid by solid-phase spectrophotometry

Solid-phase spectrophotometry (SPS) technique, in the visible region, was used for the spectrophotometric determination of ascorbic acid based on the reducing effect on iron(III) ion, followed by formation of the iron(II)-ferrozine chelate. The chelate is easily sorbed on a dextran-type anion-exchange gel and the absorbance of the resin at 567 and 800 nm, packed in a 1 mm cell, is measured directly. The apparent molar absorptivity using 100 ml of sample was 2.1×10⁷ l mol⁻¹ cm⁻¹ and it allowed the determination of ascorbic acid in the range 5–90 ng ml⁻¹; the detection limit was 0.91 ng ml⁻¹ and the RSD 0.91% for a concentration of 50 ng ml⁻¹ of ascorbic acid (n=10). The proposed method permits a highly sensitive and selective determination of ascorbic acid without any preconcentration and it has been satisfactorily applied for its determination in fruit juices, pharmaceuticals, urine and conservative liquids.     

Spectrophotometric determination of lead in vegetables with dibromo-p-methyl-carboxysulfonazo

A new highly sensitive and selective chromogenic reagent dibromo-p-methyl-carboxysulfonazo (DBMCSA) was synthesized and studied for the spectrophotometric determination of lead in detail. In 0.25 M phosphoric acid medium, which greatly increases the selectivity, lead reacts with DBMCSA to form a 1:2 blue complex, having a sensitive absorption peak at 648 nm. Under the optimal conditions, Beer's law is obeyed over the range from 0 to 0.8 μg ml⁻¹ Pb(II) and the apparent molar absorptivity is 1.04×10⁵ l mol⁻¹ cm⁻¹. The detection limit and the variation coefficient were found to be 2.14 ng ml⁻¹ and 1.0%, respectively. It is found that, except for Ca(II) and Ba(II), all foreign ions studied do not interfere with determination. The interference caused by Ca(II) and Ba(II) can be easily eliminated by prior extraction with potassium iodide-methylisobutylketone. The method has been applied to the determination of lead in vegetables with satisfactory results.     

Efficiency and mechanism of new poly(acryl-phenylamidrazone phenylhydrazide) chelating fiber for adsorbing trace Ga, In, Bi, V and Ti from solution

A new po1y(acrylphenylamidrazone phenylhydrazide) chelating fiber is synthesized from polyacrylonitrile fiber and used for preconcentration and separation of trace Ga(III), In(III), Bi(III), V(V) and Ti(IV) from solution (5–50 ng ml⁻¹ Ti(IV) or V(V) and 50–500 ng ml⁻¹ Ga(III), In (III) or Bi(III) in 1000–100 ml of solution can be enriched quantitatively by 0.15 g of fiber at a 4 ml min⁻¹ flow rate in the pH range 5–7 with recoveries >95%). These ions can be desorbed quantitatively with 20 ml of 4 M hydrochloric acid at 2 ml min⁻¹ from the fiber column. When the fiber which had been treated with concentrated hydrochloric acid and washed with distilled water until neutral was reused eight times, the recoveries of the above ions by enrichment were still >95%. Two-hundred-fold to 10 000-fold excesses of Cu(II), Zn(II), Ca(II), Mn(II), Cr(III), Fe(III), Ba(II) and Al(III) caused little interference in the determination of these ions by inductively coupled plasma-atomic emission spectrometers (ICP-AES). The relative standard deviations for enrichment and determination of 50 ng ml⁻¹ Ga, In or Bi and 10 ng ml⁻¹ V or Ti are in the range 1.2–2.7%. The contents of these ions in real solution samples determined by this method were in agreement with the certified values of the samples with average errors <3.7%.     

Semi-quantitative trace analysis of nuclear fast red by surface enhanced resonance Raman scattering

The dye nuclear fast red has been detected and determined semi-quantitatively by means of surface enhanced resonance Raman scattering (SERRS) and surface enhanced Raman scattering (SERS), using laser exciting wavelengths of 514.5 and 632.8 nm, respectively, by employing a citrate-reduced silver colloid. A good linear correlation is observed for the dependence of the intensities of the SERRS bands at 989 cm⁻¹ (R=0.9897) and 1278 cm⁻¹ (R=0.9872) on dye concentration over the range 10⁻⁹ to 10⁻⁷ M, when using an exciting wavelength of 514.5 nm. At dye concentrations above 10⁻⁷ M, the concentration dependence of the SERRS signals is non-linear. This is almost certainly due to the coverage of the colloidal silver particles being in excess of a full monolayer of the dye. A linear correlation is also observed for the dependence of the intensities of the SERS bands at 989 cm⁻¹ (R=0.9739) and 1278 cm⁻¹ (R=0.9838) on the dye concentration over the range 10⁻⁸ to 10⁻⁶ M when using an exciting wavelength of 632.8 nm. Strong fluorescence prevented collection of resonance Raman scattering (RRS) spectra from powdered samples or aqueous solutions of the dye using an exciting wavelength of 514.5 nm, but weak bands were observed in the spectra obtained from both powdered and aqueous samples of the dye using an exciting wavelength of 632.8 nm. A study of the pH dependence of SERRS/SERS and UV–VIS absorption spectra revealed the presence of different ionisation states of the dye. The limits of detection for nuclear fast red by SERRS (514.5 nm), SERS (632.8 nm) and visible spectroscopy (535 nm) are 9, 89 and 1000 ng ml⁻¹, respectively.     

Speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry

A simple procedure was developed for the speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry (EcHG–AAS), without pre-reduction of As(V). Glassy carbon was selected as cathode material in the flow cell. An optimum catholyte concentration for simultaneous generation of arsine from As(III) and As(V) was 0.06 mol l⁻¹ H₂SO₄. Under the optimized conditions, adequate sensitivity and difference in ratio of slopes of the calibration curves for As(III) and As(V) can be achieved at the electrolytic currents of 0.6 and 1 A. The speciation of inorganic arsenic can be performed by controlling the electrolytic currents, and the concentration of As(III) and As(V) in the sample can be calculated according to the equations of absorbance additivity obtained at two selected electrolytic currents. The calibration curves were linear up to 50 ng ml⁻¹ for both As(III) and As(V) at 0.6 and 1 A. The detection limits of the method were 0.2 and 0.5 ng ml⁻¹ for As(III) and As(V) at 0.6 A, respectively. The relative standard deviations were of 2.1% for 20 ng ml⁻¹ As(III) and 2.5% for 20 ng ml⁻¹ As(V). The method was validated by the analysis of human hair certified reference material and successfully applied to speciation of soluble inorganic arsenic in Chinese medicine.     

Determination of As(III) and total inorganic arsenic by flow injection hydride generation atomic absorption spectrometry

A simple procedure was developed for the direct determination of As(III) and As(V) in water samples by flow injection hydride generation atomic absorption spectrometry (FI–HG–AAS), without pre-reduction of As(V). The flow injection system was operated in the merging zones configuration, where sample and NaBH₄ are simultaneously injected into two carrier streams, HCl and H₂O, respectively. Sample and reagent injected volumes were of 250 μl and flow rate of 3.6 ml min⁻¹ for hydrochloric acid and de-ionised water. The NaBH₄ concentration was maintained at 0.1% (w/v), it would be possible to perform arsine selective generation from As(III) and on-line arsine generation with 3.0% (w/v) NaBH₄ to obtain total arsenic concentration. As(V) was calculated as the difference between total As and As(III). Both procedures were tolerant to potential interference. So, interference such as Fe(III), Cu(II), Ni(II), Sb(III), Sn(II) and Se(IV) could, at an As(III) level of 0.1 mg l⁻¹, be tolerated at a weight excess of 5000, 5000, 500, 100, 10 and 5 times, respectively. With the proposed procedure, detection limits of 0.3 ng ml⁻¹ for As(III) and 0.5 ng ml⁻¹ for As(V) were achieved. The relative standard deviations were of 2.3% for 0.1 mg l⁻¹ As(III) and 2.0% for 0.1 mg l⁻¹ As(V). A sampling rate of about 120 determinations per hour was achieved, requiring 30 ml of NaBH₄ and waste generation in order of 450 ml. The method was shown to be satisfactory for determination of traces arsenic in water samples. The assay of a certified drinking water sample was 81.7±1.7 μg l⁻¹ (certified value 80.0±0.5 μg l⁻¹).     

A flow-injection renewable surface sensor for the fluorimetric determination of vanadium(V) with Alizarin Red S

Vanadium(V) is determined by a simple bead injection spectroscopy–flow-injection analysis (BIS–FIA) system with spectrofluorimetric detection using a commercially available flow cell (Hellma 176-QS). The 500 μl of a homogeneous bead suspension of an anionic resin (Sephadex QAE A-25) previously loaded with the fluorogenic reagent 1,2-dihydroxyanthraquinone-3-sulfonic acid (Alizarin Red S) was injected to fill the flow cell. Next, V(V) is injected into the carrier and reacts with the immobilized reagent on the active solid support placed in the flow cell to form a fluorescent chelate in the absence of surfactant agents. The complex is so strongly retained on the beads that the regeneration of the solid support becomes extraordinarily difficult, so needing the renovation of the sensing surface which is achieved by means of bead injection. At the end of the analysis, beads are automatically discarded from the flow cell and transported out of the system by reversing the flow.

The measurement of fluorescence is continuously performed at an excitation wavelength of 521 nm and an emission wavelength of 617 nm. Using a low sample volume of 800 μl, the analytical signal showed a very good linearity in the range 2–60 ng ml⁻¹, with a detection limit of 0.45 ng ml⁻¹ and a R.S.D. (%) of 4.22 for 50 ng ml⁻¹ of V(V) concentration (n = 10). The sensor showed both a good selectivity, which could also be increased by the addition of EDTA and F⁻ as masking agents, and applicability to the determination of V(V) in waters, physiological samples (serum and urine) and mussel tissues.     

HPLC determination of Vitamin D(3) and its metabolite in human plasma with on-line sample cleanup

A HPLC method with automated column switching and UV-diode array detection is described for the simultaneous determination of Vitamin D₃ and 25-hydroxyvitamin D₃ (25-OH-D₃) in a sample of human plasma. The system uses a BioTrap precolumn for the on-line sample cleanup. A sample of 1 ml of human plasma was treated with 2 ml of a mixture of ethanol–acetonitrile (2:1 (v/v)). Following centrifugation, the supernatant was evaporated to dryness under a stream of dry and pure nitrogen. The residue was reconstituted in 250 μL of a solution of methanol 5 mmol l⁻¹ phosphate buffer, pH 6.5 (4:1 (v/v)), and a 200 μl aliquot of this solution was injected onto the BioTrap precolumn. After washing during 5 min with a mobile phase constituted by a solution of 6% acetonitrile in 5 mmol l⁻¹ phosphate buffer, pH 6.5 (extraction mobile phase), the retained analytes were then transferred to the analytical column in the backflush mode. The analytical separation was then performed by reverse-phase chromatography in the gradient elution mode with the solvents A and B (Solvent A: acetonitrile–phosphate buffer 5 mmol l⁻¹, pH 6.5; 20:80 (v/v); solvent B: methanol–acetonitrile–tetrahydrofuran, 65:20:15 (v/v)). The compounds of interest were detected at 265 nm. The method was linear in the range 3.0–32.0 ng ml⁻¹ with a limit of quantification of 3.0 ng ml⁻¹. Quantitative recoveries from spiked plasma samples were between 91.0 and 98.0%. In all cases, the coefficient of variation (CV) of the intra-day and inter-day-assay precision was ≤2.80%. The proposed method permitted the simultaneous determination of Vitamin D₃ and 25-OH-D₃ in 16 min, with an adequate precision and sensitivity. However, the overlap of the sample cleanup step with the analysis increases the sampling frequency to five samples h⁻¹. The method was successfully applied for the determination of Vitamin D₃ and 25-OH-D₃ in plasma from 46 female volunteers, ranging from 50 to 94 years old. Vitamin D₃ and 25-OH-D₃ concentrations in plasma were found from 4.30–40.70 ng ml⁻¹ (19.74 ± 9.48 ng ml⁻¹) and 3.1–36.52 ng ml⁻¹ (7.13 ± 7.80 ng ml⁻¹), respectively. These results were in good agreement with data published by other authors.     

Implementation of flow-through multi-sensors with bead injection spectroscopy: fluorimetric renewable surface biparameter sensor for determination of berillium and aluminum

For the first time a new, sensitive, and simple bead injection spectroscopy–flow injection analysis (BIS–FIA) system with spectrofluorimetric detection is described for the sequential determination of two metals. The sensor is based on the alternate use of two carriers and a commercially available flow cell (Hellma 176-QS). The flow cell is filled by injecting in the flow system 500 μl of a homogeneous bead suspension of an appropriate solid support (Sephadex QAE A-25) previously loaded with the fluorogenic reagent morin (2′,3,4′,5,7-pentahydroxyflavone). A sequential reaction of Al(III) and Be(II) with morin (immobilized on beads) to form their fluorescent complexes is performed on the bead sensing support and their respective fluorescence emission monitored, after doing two successive injections from the mixture solution. Firstly, Al(III) could be determined in the sample using 0.5 M NaCl/HCl, pH 6 as carrier. Then, the carrier solution was changed (0.3 M NaCl/NaOH, pH 12) making possible the elution of Al(III) and the restoration of the baseline, then allowing the reaction of Be(II). At the end of the analysis, beads are automatically discarded from the flow cell, by reversing the flow, and transported out of the system. The analytical signals are measured at an excitation wavelength of 440 nm and an emission wavelength of 520 nm. Using a sample volume of 600 μl, the analytical signal showed a very good linearity in the range 0.1–8 ng ml⁻¹ and 0.1–1 μg ml⁻¹ with detection limits of 0.024 ng ml⁻¹ and 0.010 μg ml⁻¹ for Be(II) and Al(III), respectively. R.S.D.s (%) lower than 5% were obtained for both analytes and the selectivity was improved using EDTA as masking reagent. The sensor was satisfactorily applied to the determination of these metals in waters and simulated alloy samples.     

Homogeneous stopped-flow fluoroimmunoassay using europium as label

A competitive homogeneous fluoroimmunoassay (FIA) based on the use of europium(III) as label together with kinetic methodology, is described for the first time. This approach has been applied to the determination of skatole, a compound causing boar-taint, in pig back fat samples. The analytical signal was obtained by measuring the initial rate of the dissociation reaction of europium(III) from the tracer through the formation of an intense luminescent chelate. This initial rate is higher for the free tracer than for that corresponding to the tracer bound to the antibody, and it is directly related to the analyte concentration. Each kinetic measurement was obtained in less than 1 s by using stopped-flow (SF) mixing technique. Benzoyltrifluoroacetone, tri-n-octylphosphine and Triton X-100 were used to obtain an adequate luminescent signal. The dynamic range of the calibration graph of the method is 30–300 ng ml⁻¹ and the calculated detection limit is 11 ng ml⁻¹. The precision, obtained for two skatole concentrations, 50 and 150 ng ml⁻¹, and expressed as relative standard deviation (n=11), was lower than 6.5%. The method was applied to the analysis of pig back fat samples with recoveries ranging from 92 to 108%.     

Highly selective and sensitive copper(II) membrane coated graphite electrode based on a recently synthesized Schiff’s base

A PVC membrane electrode based on bis-2-thiophenal propanediamine (TPDA) coated directly on graphite is described. The electrode exhibits a Nernstian response for Cu²⁺ over a very wide concentration range (1.0×10⁻¹ to 6.0×10⁻⁸ M) with a detection limit of 3.0×10⁻⁸ M (2.56 ng ml⁻¹). It has a fast response time and can be used for at least 2 months without any major deviation. The proposed sensor revealed very good selectivities for Cu²⁺ over a wide variety of other metal ions and could be used in the pH range of 3.0–7.0. It was successfully used for direct determination of copper in black tea and as an indicator electrode in potentiometric titration of copper ion.     

Development of an enzyme-linked immunosorbent assay for pentachlorophenol

Pentachlorophenol (PCP) is a hazardous pollutant with toxicity and potential carcinogenic properties being a serious threat to the environment. In this work, the development of an immunoassay for PCP is presented. A hapten was synthesised and conjugated to protein for rabbit immunisation. Three polyclonal antibodies were obtained and the best results were achieved in the antibody-coated format using antiserum R3. Calibration range was 0.3–30.5 ng ml⁻¹, with an average I₅₀ value of 2.9 ng ml⁻¹ and a detection limit of 0.1 ng ml⁻¹. The specificity of the assay was tested against PCP structurally related compounds. The method is highly specific for PCP and shows low cross-reactivity (CR) for chlorine-containing phenols, nitrophenols, benzenic and piridinic compounds. The good recoveries achieved with different water samples indicate that this assay can be a good alternative method for the determination of PCP in this kind of samples.     

Reverse flow injection spectrophotometric determination of iron(III) using chlortetracycline reagent

A simple reversed flow injection colourimetric procedure for determining iron(III) was proposed. It is based on the reaction between iron(III) with chlortetracycline, resulting in an intense yellow complex with a suitable absorption at 435 nm. A 200 μl chlortetracycline reagent solution was injected into the phosphate buffer stream (flow rate 2.0 ml min⁻¹) which was then merged with iron(III) standard or sample in dilute nitric acid stream (flow rate 1.5 ml min⁻¹). Optimum conditions for determining iron(III) were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.5–20.0 μg ml⁻¹. The detection limit (3σ) and the quantification limit (10σ) were 0.10 and 0.82 μg ml⁻¹, respectively. The relatives standard deviation of the proposed method calculated from 12 replicate injections of 2.0 and 10.0 μg ml⁻¹ iron(III) were 0.43 and 0.59%, respectively. The sample throughput was 60 h⁻¹. The proposed method has been satisfactorily applied to the determination of iron(III) in natural waters.     

Flow injection determination of nitrite by fluorescence quenching

A simple, sensitive and selective fluorimetric method for the determination of nitrite ion in waters using a merging zones flow injection system is described. The fluorimetric determination is based on the measurement of the quenching effect produced by nitrite on proflavine (3,6-diaminoacridine) fluorescence (λ_ex/λ_em=290/519 nm).

The optimum experimental conditions were investigated by merging 0.5 ml of the sample and 0.5 ml of a solution of 5 mg l⁻¹ of proflavine (in 0.1 M HCl) in a flow injection system, on-line connected to a flow-cell placed in the conventional sample compartment of a spectrofluorimeter. The selected carrier solution and final flow rate were 0.1 M HCl and 0.5 ml min⁻¹, respectively. A reaction coil of 2 ml was used. As a result of the simplicity of this system, a sample throughput of about 50 samples h⁻¹ can be achieved with the proposed methodology.

The detection limit was 1.1 ng ml⁻¹ (3σ criterion) of nitrite. The repeatability for five sample injections containing 100 ng ml⁻¹ of nitrite was ±0.3% and the observed linear range extended up to 400 ng ml⁻¹. Also, the effect of interferences from various metals and anions commonly present in waters was also studied.

The method was successfully applied to the determination of low levels of nitrite in different water samples (river, fountain, tap and commercial drinking waters).     

Spectral studies on the interaction of Amido black 10B with DNA in the presence of cetyltrimethylammonium bromide

The interaction of Amido black 10B (AB) with DNA in basic medium was studied in the presence of cetyltrimethylammonium bromide (CTMAB) based on the measurements of resonance light scattering (RLS), UV–vis, CD spectra, and RLS imaging. The interaction has been proved to give a ternary complex of CTMAB–DNA–AB in Britton–Robinson buffer of pH 11.55, which exhibits strong negative Cotton effect at 233.3 nm and 642.8 nm, and strong RLS signals characterized at 469 nm. Experiments showed that the enhanced RLS intensities (ΔI_RLS) against the mixture of AB and CTMAB are proportional to the concentration of fish sperm DNA (fsDNA) and calf thymus DNA (ctDNA), respectively over the range of 0.03–1.0 and 0.05–1.5 μg ml⁻¹, with the limits of determination (3σ) of 7.3 ng ml⁻¹ for fsDNA and 7.0 ng ml⁻¹ for ctDNA.     

Resonance Rayleigh scattering, second-order scattering and frequency doubling scattering methods for the indirect determination of penicillin antibiotics based on the formation of Fe3[Fe(CN)6]2 nanoparticles

Under the HCl solution and heating condition, penicillin antibiotics such as amoxicillin (AMO), ampicillin (AMP), sodium cloxacillin (CLO), sodium carbenicillin (CAR) and sodium benzylpenicillin (BEN) could react with Fe(III) to produce Fe(II) which further reacted with Fe(CN)₆³⁻ to form a Fe₃[Fe(CN)₆]₂ complex. By virtue of hydrophobic force and Van der Waals force, the complex aggregated to form Fe₃[Fe(CN)₆]₂ nanoparticles with an average diameter of 45 nm. This resulted in a significant enhancement of resonance Rayleigh scattering (RRS) and non-linear scattering such as second-order scattering (SOS) and frequency doubling scattering (FDS). The increments of scattering intensity (ΔI) were directly proportional to the concentrations of the antibiotics in a certain range. The detection limits for the five penicillin antibiotics were 2.9–6.1 ng ml⁻¹ for RRS method, 4.0–6.8 ng ml⁻¹ for SOS method and 7.4–16.2 ng ml⁻¹ for FDS method, respectively. Among them, the RRS method exhibited the highest sensitivity and the AMO system was more sensitive than other antibiotics systems. Based on the above researches, a new highly sensitive and simple method for the indirect determination of penicillin antibiotics has been developed. It can be applied to the determination of penicillin antibiotics in capsule, tablet, human serum and urine samples. In this work, the spectral characteristics of absorption, RRS, SOS and FDS spectra, the optimum conditions of the reaction and the influencing factors were investigated. In addition, the reaction mechanism was discussed.     

Application of a new resin functionalised with 6-mercaptopurine for mercury and silver determination in environmental samples by atomic absorption spectrometry

Polystyrene–divinylbenzene (8%) has been functionalised by coupling it through an ---N=N--- group with 6-mercaptopurine. The resulting chelating resin has been characterised by using elemental analysis, thermogravimetric analysis and infrared spectra. The resin is highly selective for Hg(II) and Ag(I) and has been used for preconcentrating Hg(II) and Ag(I) prior to their determination by atomic absorption spectrometry. The maximum sorption capacity for Hg(II) and Ag(I) was found to be 1.74 and 0.52 mmol g⁻¹, respectively, over the pH range 5.5–6.0. The calibration range for Hg(II) was linear up to 10 ng ml⁻¹ with a 3σ detection limit of 0.02 ng ml⁻¹; the calibration range for Ag(I) was linear up to 5 μg ml⁻¹ with a detection limit of 29 ng ml⁻¹. The recoveries of the metals were found to be 99.7±3.8 and 101.3±4.1% at the 95% confidence level for both Hg(II) and Ag(I). In column operation, it has been observed that Hg(II) and Ag(I) in trace quantities can be selectively separated from geological, medicinal and environmental samples.     

Simple flow-injection system for the simultaneous determination of nitrite and nitrate in water samples

A novel spectrophotometric reaction system was developed for the determination of nitrite as well as nitrate in water samples, and was applied to a flow-injection analysis (FIA). The spectrophotometric flow-injection system coupled with a copperised cadmium reductor column was proposed. The detection was based on the nitrosation reaction between nitrite ion and phloroglucinol (1,3,5-trihydroxybenzene), a commercially available phenolic compound. Sample injected into a carrier stream was split into two streams at the Y-shaped connector. One of the streams merged directly and reacted with the reagent stream: nitrite ion in the samples was detected. The other stream was passed through the copperised cadmium reductor column, where the reduction of nitrate to nitrite occurred, and the sample zone was then mixed with the reagent stream and passed through the detector: the sum of nitrate and nitrite was detected. The optimised conditions allow a linear calibration range of 0.03–0.30 μg NO₂⁻-N ml⁻¹ and 0.10–1.00 μg NO₃⁻-N ml⁻¹. The detection limits for nitrite and nitrate, defined as three times the standard deviation of measured blanks are 2.9 ng NO₂⁻-N ml⁻¹ and 2.3 ng NO₃⁻-N ml⁻¹, respectively. Up to 20 samples can be analyzed per hour with a relative standard deviation of less than 1.5%. The proposed method could be applied successfully to the simultaneous determination of nitrite and nitrate in water samples.     

Second derivative spectrophotometric method for simultaneous determination of cobalt, nickel and iron using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A simple, sensitive and rapid derivative spectrophotometric method using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been developed for simultaneous determination of Co(II), Ni(II) and Fe(II) which have very similar chemical behavior and appear together in many real samples. The complexes of all these metal ions with 5-Br-PADAP were formed immediately at pH 7.0 ammonium acetate buffered solution and were stable for at least 24 h. Second derivative spectra were selected for evaluation, because working wavelength determination was more precise and spectral overlap was less than in the ordinary and first derivative spectra. Three wavelengths at which the complexes exhibit extremum ²D values for Co(II), Ni(II) and Fe(II) were selected as analytical wavelengths, i.e., 640, 600 and 740 nm, respectively. Calibration curves drawn with zero-to-peak values at mentioned wavelengths were linear between 80 and 2000 ng ml⁻¹ for each metal ion. Concentrations of Co(II) and Ni(II) were calculated from the total ²D values and the sum of the linear equations for these three cations at 640 and 600 nm, after Fe(II) assay by making use of the ²D value at 740 nm. Limits of detection (LOD) for Co(II), Ni(II) and Fe(II) were 2.7, 13.9 and 3.0 ng ml⁻¹, respectively. The method has been applied to tool steel and heater resistance wire samples successfully.     

Spectrophotometric determination of ascorbic acid using copper(II)-neocuproine reagent in beverages and pharmaceuticals

The proposed method for ascorbic acid (Vitamin C) (AA) determination is based on the oxidation of AA to dehydroascorbic acid with a Cu(II)-2,9-dimethyl-1,10-phenanthroline (neocuproine (Nc)) reagent in ammonium acetate-containing medium at pH 7, where the absorbance of the formed bis(Nc)-copper(I) chelate is measured at 450 nm. This chelate was formed immediately and the apparent molar absorptivity for AA was found to be 1.60 × 10⁴ dm³ mol⁻¹ cm⁻¹. Beer's law was obeyed between 8.0 × 10⁻⁶ and 8.0 × 10⁻⁵ M concentration range. The relative standard deviation for 90 μg AA was 3%. The Cu(II)-Nc reagent is a milder and therefore more selective oxidant than the conventional Fe(III)-1,10-phenanthroline (phen) reagent used for the same assay. This feature makes the proposed method superior for real samples such as fruit juices containing weak reductants such as citrate, oxalate and tartarate that otherwise produce positive errors in the Fe(III)-phen method when equilibrium is achieved. The developed method was applied to a number of commercial fruit juices, pharmaceutical preparations containing Vitamin C, and red wine. The meta-bisulfite content of wine was removed with an anion exchanger at pH 3 prior to analysis, and a difference extractive–spectrophotometric method of AA assay in wine was developed so as to suppress the interferences caused by wine anthocyanins and polyphenols. The findings of the developed method for fruit juices and pharmaceuticals were also statistically compared with those of HPLC so as to establish it as a reliable novel method.