烃类在ZSM-5分子筛上吸附的研究

本文对烃类在不同ZSM-5分子筛上吸—脱附的动态行为进行了研究。描述了程序升温脱附过程中扩散系数和扩散活化能的计算模型;测定了环己烷在ZSM-5分子筛样品上的迎头流出曲线。发现环己烷在ZSM-5分子筛上的吸附存在着可逆和不可逆两个过程,后者受环己烷在分子筛内部孔道的扩散所制约,同时不同样品上吸附性能的差异与X-射线衍射峰的特征以及甲醇转化为汽油的反应性能之间存在着密切关系。谱图属A 型的ZSM-5分子筛对环己烷有较大的吸附量、较小的孔道扩散障碍和较好的甲醇转化反应稳定性。     

氧在Co3O4催化剂上的化学吸附

测定了氧在氨氧化催化剂Co_3O_4上于100—400℃下的吸附动力学和室温-600℃的热脱附谱,并与离子探针质谱测定的结果进行了比较。动力学曲线指出氧具有快速和慢速不同类型的吸附,热脱附谱显示有相应的脱附曲线。快速吸附对应于两个脱附峰,峰的极大值温度各为165℃,380—420℃;相应的吸附氧粒子可指定为O_2~-,O~-;脱附活化能分别为13.3千卡/克分子,26.7千卡/克分子。慢速吸附服从Elovich吸附规律,吸附过程可能是快速吸附的氧粒子在催化剂表面上迁移生成O~(2-)并入氧化物表面晶格,脱附温度高于500℃时可由表面晶格中逸出。吸附中心可能是表面Co~(2+)离子。讨论了氧吸附与氨催化氧化反应之间的关系。     

环戊烷在silicalite-1分子筛上的扩散性能的研究

采用智能重量分析技术（Intelligent-Gravimetric Analysis）研究了环戊烷在silicalite-1分子筛上的扩散性能。同一温度下，吸附质的扩散速率随其吸附量的增加而减小，而温度越高扩散系数越大。本文同时讨论了吸附质分子的分子构型、尺寸、吸附温度和吸附量等因素对吸附质扩散性能的影响。     

用TG/DTG/DTA研究硅沸石与有机分子的主体/客体相互作用

用TG/DTG/DTA法研究无阳离子与Si—OH缺陷、结构完美的硅沸石上烃类、烷基醇、烷基胺的热脱附行为.有机分子从硅沸石上脱附的温度低于300℃其亲和性值A_T=T_d-T_b,式中T_d为有机分子在DTG上的失重峰温,T_b为该有机物在标准压力下的沸点.饱和烷烃的A_T值为60～90,而苯、甲苯、对二甲苯等的A_T值为6～13.电负性较强的羟基使烷基醇与硅沸石的亲和性明显下降.多羟基醇的A_T值为负值.对二甲苯、烷基醇、烷基胺在脱附时有明显吸热效应.A_T值及脱附热效应的不同是硅沸石骨架0~(2-)微孔表面与有机分子C—H基因,其它极性基因之间相互作用不同,以及受到硅沸石骨架空间限制的被吸附分子间缔合情况不同所致,反应了不同类型的主体/客体超分子相互作用.     

CuO/Ti0.5Zr0.5 O2催化剂上NO+CO反应活性的研究

以Ti0.5Zr0.5O2复合氧化物为载体，采用浸渍法制备了不同负载量的CuO／Ti0.5Zr0.5O2(TZ)催化剂，考察了催化剂对NO的反应活性，并用TPR、TG-DTA和NO-TPD等技术对催化剂进行了表征。结果表明，CuO的负载量和焙烧温度对催化剂的活性均有影响。30％CuO／Ti0.5Zr0.5O2(500℃，2h)在反应温度为400℃时NO转化率为100％。TPR结果表明，CuO负载量≤12％时，在TPR上出现了2个还原峰(即α和β峰)；而进一步提高CuO的负载量，出现了γ还原峰，推测α峰为高度分散Cu物种的还原，β峰为孤立的Cu物种的还原，γ峰则为晶相CuO的还原峰。TG-DTA图谱显示在725℃左右的放热峰是ZrTiO4晶化过程的完成。NO-TPD结果表明NO吸附在TZ上的热脱附过程中，出现2个脱附峰；而NO吸附在12％CuO／TZ上，500℃和750℃焙烧的催化剂上出现3个脱附峰；而在850℃和950℃焙烧的催化剂上只出现2个脱附峰，且NO在上述不同焙烧温度的催化剂上的脱附峰温均低于载体，这表明NO吸附在CuO／TZ催化剂上比吸附在Ti0.5Zr0.5O2上更容易脱出和分解。     

C5烷烃分子在AlPO4-5分子筛中吸附的分子模拟研究

采用分子水平计算机模拟方法研究了环戊烷、正戊烷和2－甲基丁烷在AlPO4-5分子筛中的吸附，得到了有关吸附平衡常数、吸附热、吸附等温线以及平均势能等。结果表明，在373 K，2－甲基丁烷的饱和吸附量高于其他两种异构体；473 K，环戊烷的饱和吸附量高于其他两种异构体；573 K，在所测试的压力范围内，环戊烷的吸附量都高于其他两种异构体，2－甲基丁烷的吸附量高于正戊烷。C5烷烃分子在AlPO4-5中吸附量的不同是由于他们在分子筛中的排列方式不同而引起的。低吸附量时C5烷烃分子平均势能不随吸附量变化；高吸附量时平均势能随着吸附量的增加而降低；而2－甲基丁烷和环戊烷分子的平均势能变化更加明显。     

城市污水污泥燃烧特性和动力学特性分析

采用热重分析仪对城市污水污泥进行热重实验,通过TG(热重)、DTG(微分热重)和DSC(差示扫描量热)曲线的分析对比,获得污水污泥热解和燃烧不同阶段的特性。低于250℃,燃烧与热解的热重曲线基本吻合,说明在此之前,失重速率主要受控于有机物的分解以及析出,燃烧过程对失重影响不明显。燃烧DTG曲线呈现“W”峰型,第一个失重速率峰与热解DTG曲线基本对应,高于410℃,燃烧DTG曲线出现显著的加速。采用Coats-Redfern 积分法,假设不同的反应模型进行拟合,推断出污泥燃烧过程中两个DTG峰体现出不同的反应机理。借鉴煤燃烧机理分析认为,污泥燃烧反应初期挥发分的燃烧受控于化学反应速率,随着温度的不断提高,剩余挥发分的燃尽和固定碳的燃烧总反应速率逐渐受扩散因素控制。基于分析所得污泥燃烧机理,采用四个独立的平行反应模型模拟污泥的燃烧过程,拟合曲线与实验数据吻合良好。     

用TG/DTG/DTA研究硅沸石与有机分子的主体/客体相互作用

用TG/DTA/DTA法研究无阳离子与Si-OH缺陷、结构完美的硅沸石上烃类、烷基醇、烷基胺的热脱附行为。有机分子从硅沸石上脱附的温度低于300℃。其亲和性值AT=Td-Tb, 式中Td为有机分子在DTG上的失重峰温, Tb为该有机物在标准压力下的沸点。饱和烷烃的AT值为60~90, 而苯、甲苯、对二甲苯等的AT值为6~13。电负性较强的羟基使烷基醇与硅沸石的亲和性明显下降。多羟基醇的AT值为负值。对二甲苯、烷基醇、烷基胺在脱附时有明显吸热效应。AT值及脱附热效应的不同是硅沸石骨架O^2^-微孔表面与有机分子C-H基团, 其它极性基团之间相互作用不同, 以及受到硅沸石骨架空间限制的被吸附分子间缔合情况下同所致, 反应了不同类型的主体/客体超分子相互作用。     

乙酸丁酯废气在活性炭上的吸附和脱附行为研究

对4种商品化活性炭进行了SEM、N_2低温物理吸附等分析表征,结合吸附穿透曲线、饱和吸附量等筛选出适用于乙酸丁酯废气吸附的活性炭(编号为AC4)。分别研究了空塔气速、废气湿度等对吸附过程的影响,同时测定了25℃、40℃和60℃下不同进气浓度的饱和吸附量,并采用Langmuir和Freundlish等温吸附方程对实验数据进行拟合,结果表明,langmuir等温吸附方程能更好地描述乙酸丁酯废气在活性炭上的吸附。采用热空气脱附法对活性炭进行再生并回收乙酸丁酯,设计出在空气流速为0.2m/s时,先在140℃下脱附1.5h,然后在170℃下脱附1.5h的脱附再生工艺。在此条件下,乙酸丁酯脱附率达97.99%,回收率达89.51%。     

Pt/TiO_2催化剂上的氢—氧作用 Ⅰ.氢、氧的吸咐—脱附行为以及相互促进作用

本文采用程序升温脱附(TPD)技术研究了光沉积方法制备的Pt/TiO_2催化剂经过氧化、还原后氧、氢的脱附行为.光沉积过程中,Pt/TiO_2表面上可以生成大量的吸咐氢,在TPD中脱附;同时Pt/TiO_2表面上化学吸附的水在TPD过程中也可以分解释氢.氧化处理的Pt/TiO_2在TPD过程中于550～750K温区出现氧脱附峰,随着氧化温度升高,脱附峰位向高温移动,经实验证明,这种可脱附活泼氧物种的生成是由样品前身中留存氢引起的.还原处理的Pt/TiO_2在TPD过程中分别在300～600和大于600K出现两个氢脱附峰,认为是由于表面羟基和钛—氢(Ti~(4+)—H~-)物种的分解释氢引起的Pt/TiO_2上活泼氧物种的存在,增加了样品在室温条件下的吸氢量;在中温(473～573K)这种活泼氧物种则和氢发生反应,减少了TPD过程中的脱氢量;Pt/TiO_2在大于673K温度还原,可以消除活泼氧物种的影响.     

环戊烷和环己烷在silicalite-1上的吸附、扩散和热脱附

Adsorption,diffusion and thermal desorption features of cyclopentane and cyclohexane in silicalite-1 have beeninvestigated using the intelligent gravimetric technique.Both the saturation adsorption loadings and diffusion coef-ficient of cyclopentane were greater than those of cyclohexane.The diffusivity of cyclopentane was about one orderof magnitude greater than that of cyclohexane at the same temperature and initial loading.For cyclopentane,therewas only one kind of desorption process at adsorption loadings lower than 4 muc(molecule per unit cell),but twodesorption processes appeared at the adsorption loadings higher than 4 muc.While for cyclohexane,one desorptionprocess was found in the whole range of loadings.Both thermal desorption peaks of cyclopentane and cyclohexanemoved to higher temperature region with increasing loading.     

Application of quasi-equilibrated thermodesorption of hexane and cyclohexane for characterization of porosity of zeolites and ordered mesoporous silicas

Quasi equilibrated temperature programmed desorption and adsorption (QE-TPDA) of hexane and cyclohexane was applied for characterization of zeolites 5A, ZSM-5, 13X, Y, NaMOR and ordered mesoporous silicas MCM-41, MCM-41/TMB, SBA-15 and HMS. Similar QE-TPDA profiles of hexane and cyclohexane with a single desorption maximum were observed for the wide pore zeolites. No adsorption of cyclohexane for zeolite 5A and a single desorption maximum for ZSM-5 were found, while two-step desorption profiles of hexane were observed for these zeolites. Similar values of the adsorption enthalpy and entropy of hexane and cyclohexane were obtained by fitting the Langmuir model functions for the zeolites X and Y. For NaMOR and ZSM-5 larger differences in these parameters were found. A single desorption peak found at low temperatures in the QE-TPDA profiles of hexane and cyclohexane for the studied silicas was attributed to the multilayered adsorption on their mesopore surface. The adsorption isobars calculated from the thermodesorption profiles were fitted with the BET function. This way values of the specific surface area and the adsorption heat were calculated. Additionally values of the initial heat of adsorption were found by fitting the Henry’s law to the high-temperature sections of the linearized isobars. The largest deviations from the BET and Henry functions and the largest values of the adsorption heats found for SBA-15 indicated the greatest heterogeneity of the adsorption sites on its surface.     

MFI沸石上对二甲苯的热脱附

MFI沸石（ZS－5型）的骨架结构内含十氧元环的二维孔道［‘］，孔容积0．18cm‘·g－‘，硅沸石（Silicallte－1）是骨架中不合铝的ZSM－5．’‘StMASNMR话可揭示沸石的结构对称性、硅铝比和局部缺陷［习．Nagy等人间提出St－OH缺陷在含铅量高时形成．Woolery等门则认为出OH完全是由于骨架内包藏的桂的存在而产生，并随铝合量降低而增大．ZSM－5、硅沸石的结构特征和对二甲苯（Px）的性质决定了Px在ZSM－5上的吸附特性·本文用’‘StMASNLDEL表征硅沸石及不同含铅量的H、Na型ZSM－5的结构，并用＊W＊＊G巾TA分析吸附于…     

烃在HZSM-5沸石上的程序升温脱附

本文研究了烃在HZSM-5沸石上的程序升温脱附(TPD).正己烷、环己烷和苯的TPD谱只有一个陡峰,对和间二甲苯的TPD谱均呈现出双峰.实验测得脱附活化能的次序为:正己烷>对二甲苯>苯>环己烷.水汽处理对正己烷的TPD影响不大;但对二甲苯的TPD影响较大.随着吸附量的增大,二甲苯逐渐占据孔道深处的强活性位置.     

Adsorption of n-hexane in zeolite-5A: a temperature-programmed desorption and IR-spectroscopic study

The adsorption and desorption of n-hexane over Zeolite-5A has been investigated as a function of loading using simultaneous Fourier transform infrared (FTIR)-temperature-programmed desorption (TPD) measurements. The TPD profiles show a second peak developing at lower temperatures when loading exceeds 16 hexane molecules per Zeolite-5A unit cell or two molecules per alpha-cavity of the Zeolite-5A structure. The infrared spectra rule out two types of adsorption sites as the origin of the two peaks in the TPD. Changes in the conformation of the adsorbed hexane as a function of loading and temperature were followed by monitoring the position of the methylene stretching modes in the infrared spectra. With increasing loading, the adsorbed hexane adopts a stretched trans conformation. These changes occur at loading levels below 12 hexane molecules per Zeolite-5A unit cell. No change is observed above this loading, ruling out any conformational change at loadings where the second peak is seen in the TPD. The second peak in the TPD arises, therefore, from a combination of steric repulsion and loss of translational entropy.     

The Adsorption and Thermal Decomposition of CH2CO (CD2CO) on Si(111)-7 × 7

The adsorption and thermal decomposition of ketene on Si(l 11)-7 × 7 were investigated using various surface analysis techniques. When the surface was exposed to ketene at 120 K, two CO stretching modes at 220 and 273 meV appeared in HREELS, corresponding to two adsorbed ketene states. After the sample was annealed at ?250 K, the 273 and the 80 meV peaks vanished, indicating the disappearance of one of the adsorption states by partial desorption of the adsorbate. In a corresponding TPD measurement, a desorption peak for ketene species was noted at 220 K. Annealing the sample at 450 K caused the decomposition of the adsorbate, producing CH_x and O adspecies. Further annealing of the surface at higher temperatures resulted in the breaking of the CH bond, the desorption of H and O species and the formation of Si carbide. The desorption of H at 800 K was confirmed by the appearance of the D₂ (m/e = 4) TPD peak at that temperature when CD₂CO was used instead of CH₂CO.     

A TPD-MS study of the adsorption of ethanol/cyclohexane mixture on activated carbons

The adsorption of ethanol/cyclohexane binary mixtures on different types of activated carbons was studied in this work by temperature programmed desorption coupled with mass spectroscopy (TPD-MS). The texture, morphology and surface chemistry of the carbons were evaluated by N₂ adsorption, scanning electron microscopy (SEM) and TPD-MS techniques. The ethanol and cyclohexane TPD-MS desorption profiles showed that specific interactions between the carbon material and the adsorbate are involved during the adsorption. Most of the activated carbons adsorb strongly ethanol on the surface, leading to desorption temperatures above 100 °C. Only one carbon exhibits an affinity for cyclohexane. These observations were correlated to the different surface chemistry of the materials.     

Characterization of Extra-framework Cations in Zeolites. A temperature-programmed desorption (TPD) study

We have investigated the interaction of a few 5-ring organic compounds (cyclopentane, cyclopentene, furan, 2-methylfuran, 2,5-dihydrofuran and tetrahydrofuran) with alkali-metal cation-exchanged faujasites (LSX, X and Y types) by means of temperature-programmed desorption (TPD). The desorption behavior at higher temperatures of all probe molecules on the sodium ion containing faujasites with different Si/Al ratios reflects the higher cation content of zeolites with greater aluminum content. Only the desorption profiles of tetrahydrofuran and 2,5-dihydrofuran show, depending on the kind of cation, additional desorption features at higher temperatures. Using a regularization method, desorption energy distribution functions for furan and tetrahydrofuran were calculated. The calculated desorption energy distributions clearly illustrate the very different adsorption behavior of furan and tetrahydrofuran which leads to large differences in the binding energies between the corresponding adsorption complexes. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermogravimetric characterisation of poly(methyl methacrylate) photopolymerised by colloidal cadmium sulphide

The thermal stability of poly(methyl methacrylate) (PMMA) photopolymerised using colloidal cadmium sulphide as the photoinitiator was studied by thermogravimetry (TG) and differential TG (DTG).The thermal stability of the CdS initiated PMMA was greater than that of conventional radically polymerised PMMA and approached that of anionically prepared PMMA. The DTG curve of the CdS initiated PMMA was a composite of four peaks, three of which correspond to the three peaks observed in the DTG curve of standard radically prepared PMMA. It is suggested that the additional peak arises from a new mode of depolymerisation initiation, that is, from chain end unsaturation introduced into the polymer chain during polymerisation initiation with the colloidal CdS.