气相色谱-质谱联用检验稻田水中双甲脒农药残留的研究

建立了稻田水中双甲脒的液液萃取/气质联用检验方法。考察了不同的提取溶剂和PH值对检测结果的影响,使用GC-MS选择离子监测模式检测。在优化条件下,双甲脒在20~2000ng/mL范围内具有良好的线性关系,相关系数为0.9991,平均回收率为86.7%,精密度（n=5）为5.3%,检出限为10ng/mL。该方法快速、灵敏、准确,可用于稻田水中双甲脒的定性定量分析检验。     

气相色谱-质谱联用检测稻田水中的双甲脒农药残留

建立了用于检测稻田水中双甲脒农药残留的液液萃取/气质联用方法。使用GC-MS选择离子监测模式检测,考察了不同的提取溶剂和pH对检测结果的影响。在优化条件下,双甲脒在20~2000ng/mL范围内具有良好的线性关系,相关系数为0.9991,平均回收率为86.7%,精密度(n=5)为5.3%,检出限为10ng/mL。该方法快速、灵敏、准确,可用于稻田水中双甲脒的定性定量分析检验。     

固相支撑液液萃取/气相色谱-串联质谱法同时测定血液中双甲脒、杀虫脒及其代谢产物

建立了气相色谱-串联质谱法同时测定血液中双甲脒、杀虫脒及其代谢产物的分析方法。优化了样品前处理方法及气相色谱-串联质谱的分析条件,样品经固相支撑液液萃取柱(SLE)净化,乙腈-二氯甲烷(体积比1∶1)洗脱后,在多反应监测模式(MRM)下检测。结果表明,2,4-二甲基苯胺、4-氯邻甲苯胺和双甲脒在1.0~1 000 ng/m L范围内,其余目标物在2.0~1 000 ng/m L范围内线性关系良好,相关系数均大于0.99;定量下限为1.0~2.0 ng/m L,加标回收率为88.6%~113%。该方法简便、快捷、样品用量小,结果准确可靠,灵敏度高,适用于血液中6种目标物的同时检测。     

固相微萃取气相色谱质谱联用同时测定鱼塘水中26种常见投毒农药

建立了固相微萃取气质联用同时检测鱼塘水中26种常见农药的方法。通过正交试验设计,确定萃取条件为100μm PDMS萃取头,pH 7,20℃萃取30min,搅拌200 r/min。优化了气相色谱和质谱条件,样品在25 min内测试完成。该方法检测鱼塘水样品中混合标准溶液的回收率在72%~118%之间,相对标准偏差在1.2%~15.8%之间,检出限为0.001~1.3ng/m L。本法成功应用于真实鱼塘水投毒案例中高效氯氟氰菊酯的定性检测。     

固相萃取-高效液相色谱法测定水果中单甲脒的残留量

建立了固相萃取-高效液相色谱法(SPE-HPLC)测定水果中农药单甲脒残留量的检测方法.用HCl溶液将样品中单甲脒转化为盐酸盐并溶于水中,在碱性条件下用乙腈提取,经碱性氧化铝固相萃取柱净化.采用C18柱(250 mm×4.6 mm,5 μm)分离,以甲醇-0.01 mol/L乙酸铵溶液(50∶ 50, V/V)为流动相,在254 nm下检测.本方法可以将单甲脒与基质良好分离,在0.01～10 mg/L浓度范围内线性良好(R2=0.9999);检出浓度为0.0013 mg/kg,回收率为80.7%～95.3%,相对标准偏差小于7%,可用于水果中单甲脒残留量的检测.     

分散固相萃取净化/液相色谱-串联质谱法同时测定蜂王浆中双甲脒、单甲脒及其代谢物

建立了分散固相萃取净化/液相色谱-串联质谱(dSPE/LC-MS/MS)测定蜂王浆中双甲脒、单甲脒(DMPF)及其代谢物2,4-二甲基苯基甲酰胺(DMF)和2,4-二甲基苯胺(DMA)残留量的方法。样品经缓冲溶液(pH 9.0)稀释,乙腈和氯化钠进行蛋白沉淀、盐析提取后,通过N-丙基乙二胺(PSA)、C_(18)和无水硫酸镁进行分散固相萃取净化。净化液过0.22μm滤膜后,采用Agilent Eclipse XDB-C_(18)柱(150 mm×4.6 mm,5μm)分离,以0.15%甲酸溶液-乙腈为流动相进行梯度洗脱,采用电喷雾离子源正离子方式扫描,多反应监测模式进行检测,同位素内标法定量。结果表明,双甲脒、DMPF、DMF和DMA的线性范围为0～100μg/kg,相关系数(r)大于0.996,方法定量下限(S/N=10)分别为0.10、0.25、5.0、2.5μg/kg。对空白蜂王浆进行5、10、20μg/kg浓度水平的加标实验,回收率为77.0%～107%,相对标准偏差为2.0%～11%。该方法简便、快捷,适用于蜂王浆中双甲脒、DMPF及其代谢物残留量的同时测定。     

固相萃取-气相色谱法检测枸杞子中啶虫脒的残留量

采用固相萃取-气相色谱法检测枸杞子中啶虫脒残留量。用乙腈提取样品中的啶虫脒,活性炭和中性氧化铝串联固相萃取柱净化,用气相色谱微电子捕获检测器进行检测。在0.02~5.0mg/L的浓度范围内,啶虫脒的线性关系良好,相关系数r=0.9999,回收率在81.3%~108.8%之间,检出限为0.005mg/kg。该方法可用于枸杞子中啶虫脒残留量的测定。     

在线固相萃取-超高效液相色谱-三重四极杆质谱法测定水源水和饮用水中107种典型农药及代谢产物

为进行我国水体中农药风险监测,针对水体中农药种类多、浓度低的特点,建立了在线固相萃取-超高效液相色谱-串联质谱法快速筛查和检测水源水及饮用水中107种典型农药及代谢产物(有机磷类、有机氮类、有机杂环类、氨基甲酸酯类、酰胺类、苯甲酰脲类、新烟碱类等)的方法。样品经0.22 μm孔径亲水性聚四氟乙烯滤膜过滤后,通过自动进样器取5 mL样品注入在线固相萃取系统,经X Bridge C₁₈在线固相萃取柱吸附后用纯水淋洗,以乙腈和0.1%甲酸水溶液为流动相对在线固相萃取柱梯度洗脱后再经ACQUITY HSS T₃色谱柱分离,采用电喷雾离子源正离子及负离子模式分析检测,外标法定量。以水源水及饮用水作为基质,对其准确度和精密度进行方法学验证,结果表明:107种农药及代谢产物在不同范围内线性关系良好(r²>0.995),方法检出限(LOD, S/N=3)为0.03~1.5 ng/L,定量限(LOQ, S/N=10)为0.1~5.0 ng/L。将目标分析物在1、20、50 ng/L水平下加标,水源水和饮用水中的加标回收率分别为60.6%~119.8%和61.2%~119.0%,相对标准偏差(RSD, n=6)分别为0.3%~18.6%和0.4%~17.1%。用该方法测定水源水和饮用水中的农药残留,结果显示,酰胺类、三嗪类除草剂、三唑类杀菌剂与烟碱类、氨基甲酸酯类杀虫剂有较高的检出率,其中水源水中检出含量为0.1~97.1 ng/L,饮用水中检出含量为0.1~93.6 ng/L。该方法适用于水源水和饮用水中107种典型农药及代谢产物的痕量分析测定,有效提高了水体中农药类物质的检测效率,实际应用价值较高。     

在线固相萃取-超高效液相色谱/串联质谱法测定水中新烟碱类杀虫剂

采用在线固相萃取-超高效液相色谱/串联质谱技术建立了水中啶虫脒、噻虫胺、吡虫啉、噻虫啉、噻虫嗪、呋虫胺及烯啶虫胺7种新烟碱类杀虫剂的检测方法。样品滤膜过滤后,经HLB Dierect Connect HP在线固相萃取小柱富集纯化,以ACQUITY UPLC BEH C₁₈为分析柱串联质谱进行检测,外标法定量。在线富集水样中新烟碱类物质在5.0~200 ng/L范围内线性关系良好,相关系数R²均大于0.99;检出限为0.30~2.92 ng/L,相对标准偏差均小于10%。该法可用于保障水环境安全、及时提供污染信息。     

固相萃取-气相色谱/质谱联用法测定卷烟主流烟气中的香兰素和乙基香兰素

采用固相萃取-气相色谱/质谱联用技术,建立了一种同时测定卷烟主流烟气中香兰素和乙基香兰素的方法。方法优化了萃取条件,考察了萃取溶剂、萃取时间对检测结果的影响。通过硅藻土固相萃取柱净化并浓缩后,选取DB-HeavyWAX毛细管柱进行目标物分离,以香兰素-d3作为内标,对香兰素和乙基香兰素进行定量分析。结果表明,香兰素和乙基香兰素在浓度0.2~20.0 mg/L范围内具有良好的线性关系,其检出限分别为9.1 ng/支和6.5 ng/支,回收率均在96.3%~107.7%之间。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

A study of the spinel materials LiTi2O4 and Li43Ti53O4 by photoelectron spectroscopy

HeI-excited valence-band ultraviolet photoelectron spectra and MgKα-excited Ti-2p X-ray photoelectron spectra are reported for the spinel materials LiTi₂O₄ and $\text{Li}{}_{\mathrm{<mtext>4</mtext><mtext>3</mtext>}}\text{Ti}{}_{\mathrm{<mtext>5</mtext><mtext>3</mtext>}}\text{O}{}_4$. The presence of a Fermi edge in the ultraviolet photoelectron spectrum of LiTi₂O₄ confirms the metallic nature of this material, although the measured density of states at the Fermi energy is much lower than that expected from an independent-electron interpretation of the magnetic susceptibility. This difference is attributed to a strong interaction of the conduction electrons with the lattice vibrations. The localization of conduction electrons that occurs in the final state in the Ti-2p X-ray photoelectron spectrum of LiTi₂O₄ is attributed to a Coulomb interaction with a core hole.     

Oxygen defect K2NiF4-type oxides: The compounds La2−xSrxCuO4−x2+δ

Oxygen defect K₂NiF₄-type oxides $\text{La}{}_{\mathrm{2?x}}\text{Sr}{}_{\mathrm{x}}\text{CuO}{}_{\mathrm{<mtext>4?</mtext><mtext>x</mtext><mtext>2</mtext><mtext>+\delta </mtext>}}$ have been synthesized for a wide composition range: 0 ≤ x ≤ 1.34. From the X-ray and electron diffraction study three domains have been characterized: orthorhombic compounds with La₂CuO₄ structure for 0 ≤ x < 0.10, tetragonal oxides similar to LaSrCuO₄ for 0.10 ≤ x < 1 and several superstructures derived from the tetragonal cell ( with n = 3, 4, 4.5, 5, 6) for 1 ≤ x ≤ 1.34. The compounds corresponding to 0 < x < 1 differ from the other oxides in that they are characterized by the presence of copper with two oxidation states: + 2 and + 3. A model structure for La_0.8Sr_1.2CuλO_3.4, in which copper has only the + 2 oxidation state, and for which the actual cell is tegragonal—a = 18.80₄ Å and c = 12.94 Å—has been established. The particular structural evolution of these compounds is discussed in terms of a competition between the capability of Cu(II) to be oxidized to Cu(III) and the ordering of oxygen vacancies.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).