差分脉冲溶出伏安法测定陶瓷器皿中铅和镉的溶出率

采用4%的乙酸浸泡陶瓷样品24 h,应用同位镀汞差分脉冲溶出伏安法测定了陶瓷样品中微量重金属铅、镉的溶出量。以0.1 mol/L的硝酸溶液做底液,0.1 mol/L的KCl溶液做支持电解质,2 g/L的Hg2+溶液做镀汞液,测得铅的溶出峰电位为-0.5 V(vsSCE),镉的溶出峰电位为-0.7 V(vsSCE),两者含量在5×10-4～1 mg/L和5×10-4～0.5 mg/L范围内峰电流和其含量呈良好的线性关系,检出限分别为2×10-4和4.3×10-3mg/L。     

ICP–OES法测定绿茶中7种重金属元素的溶出量

建立了以电感耦合等离子体原子发射光谱(ICP–OES)法同时测定绿茶中铁、铜、锰、镍、锌、镉、铅等7种重金属元素溶出量的方法。以3种绿茶为研究对象,通过模拟实际生活中的泡茶方式,用100℃的水浸泡茶叶,过滤后用ICP–OES法进行测定。结果表明,随着浸泡时间的延长,重金属元素的溶出量逐渐增加;随着茶叶被浸泡的次数增加,重金属元素的溶出量逐渐降低。7种重金属的添加水平为0.003~4μg/m L时,加标回收率为100.00%~109.55%。测定结果的相对标准偏差为2.17%~7.13%(n=7)。检出限为0.012~0.622 mg/kg。该方法快速简单,具有良好的精密度与准确度,可用于茶叶中重金属的测定。     

ICP-AES法快速测定不锈钢食具容器中重金属的迁移量

采用ICP–AES法快速测定不锈钢食具容器中的重金属铅、铬、镍、镉和砷的迁移量。样品用4%乙酸溶液浸泡,ICP–AES法测定浸泡液中铅、铬、镍、镉、砷的含量。铅、铬、镍、镉、砷的质量浓度分别在0.03~0.30,1.0~5.0,0.3~2.0,0.015~0.20,0.020~0.30 mg/L范围内与其光谱强度线性相关,相关系数均大于0.999 6。铅、铬、镍、镉、砷的检出限分别为0.009,0.000 5,0.002,0.000 5,0.007 mg/L,加标回收率分别为100.0%~122.5%,100.0%~115.0%,99.0%~117.5%,108.0%~115.0%,60.0%~68.8%,测定结果的相对标准偏差为0.2%~5.0%(n=6)。结果表明,该方法能够满足对不锈钢食具容器中重金属迁移量的快速测定要求,可应用于食品相关产品的监管工作。     

电感耦合等离子体-质谱法测定食品容器搪瓷中可溶性铅、镉、锑含量

建立了使用电感耦合等离子体质谱技术(ICP-MS)分析食品容器搪瓷中重金属铅、镉、锑溶出量的方法.使用内标法定量,研究了使用不同浸泡浓度、浸泡时间以及浸泡次数对重金属溶出量的影响变化.对于镉、锑、铅的方法检出限分别为0.007、0.35、0.07μg/L,相对标准偏差分别为0.31%、0.87%、0.29%,回收率在78.1%~104.4%.方法快速、简便,具有较好的准确度和精密度,对进出口搪瓷制品的日常检验提供了依据.     

锑电极电位溶出法测定锌、镉、铅

提出了采用锑电极作为工作电极同时测定痕量重金属锌、镉、铅的电位溶出法。探讨了同时测定锌、镉、铅的最佳条件。在pH=5.0的HAc-NaAc缓冲溶液中,Zn2+、Cd2+、Pb2+分别在-1.07、-0.70、-0.52 V得到灵敏的电位溶出峰。沉积时间为60 s时,锌、镉、铅的质量浓度分别在0~16.0、0~1.6、0~0.08 μg/mL范围内,与各自微分电位溶出峰高呈线性关系,检出限分别为4.0、0.3、0.03 μg/L。测定了水样中痕量锌、镉、铅的含量,结果令人满意。     

石墨烯修饰铂电极传感器测定水中微量重金属镉和铅

建立了石墨烯修饰铂电极(G/Pt)共沉积铋膜测定水中微量重金属镉和铅的方法.采用微机电系统(MEMS)工艺制作铂电极,并利用CVD法在铂电极上原位生长石墨烯,制备了石墨烯修饰铂电极,与Ag/AgCl参比电极、铂丝对电极构成三电极体系;采用差分脉冲阳极溶出伏安法对水中微量的镉和铅进行测定.在pH=4.5的醋酸-醋酸钠(HAc-NaAc)底液中,Cd2+和pb2+分别在-0.72和-0.48 V灵敏地产生溶出峰,线性范围分别为0.05 ～ 10 mg/L和0.03 ～5 mg/L,检出限均为10 μg/L.本方法操作简单、安全快速、重现性好,适合于废水、地表水、及生活用水中镉和铅的测定.     

微波消解-电感耦合等离子体质谱法测定鲤鱼、河蚌样品中的铜、镉、铅、铬

建立微波消解–电感耦合等离子体质谱法同时测定鲤鱼、河蚌样品中铜、镉、铅、铬4种重金属元素的含量。以20.0μg/L的Rh作为内标,采用硝酸–过氧化氢消解液,用微波消解仪消解鲤鱼、河蚌等生物样品,在选定的仪器工作条件下测定。铜、镉、铅、铬4种重金属元素的质量浓度在1～100μg/L范围内与其质谱强度呈良好的线性关系,相关系数均为0.999 9,方法检出限为0.01～0.09μg/L。测定结果的相对标准偏差为1.30%～9.95%(n=6),样品加标回收率为91.0%～111%。用所建方法对黄鱼国家标准物质(GBW 08573)进行测定,测定值与标准值基本一致,相对误差均小于7%。该方法简单、快速,灵敏度高,重现性好,适用于大批量生物样品中多种重金属元素的同时测定。     

铋膜电极溶出伏安法测定食品中痕量重金属

以铋膜电极为工作电极,采用微分脉冲阳极溶出伏安法直接测定食品样品中痕量铅、镉和锌。在富集电位-1.4V,富集时间180s,铋膜质量浓度150μg·L-1的条件下,铋膜电极对铅、镉和锌的氧化溶出具有良好的电化学响应。铅(Ⅱ)、镉(Ⅱ)和锌(Ⅱ)的质量浓度在5.0~40μg·L-1的范围内与其阳极溶出峰电流呈线性关系,铅(Ⅱ)、镉(Ⅱ)和锌(Ⅱ)的检出限(3S/N)分别为0.80,0.65,0.58μg·L-1。对25μg·L-1铅(Ⅱ)、镉(Ⅱ)和锌(Ⅱ)溶液用铋膜电极连续测定15次,相对标准偏差分别为6.2%,5.1%,7.1%。方法应用于食品中痕量重金属的测定,测定结果与石墨炉原子吸收光谱法的测定值相符。     

电感耦合等离子体原子发射光谱法测定金属饰品中铅、镉、铬、汞、锑、砷、硒、钡、镍溶出量

金属饰品样品用硝酸(20+80)溶液浸泡过夜,采用电感耦合等离子体原子发射光谱法测定金属饰品中铅、镉、铬、汞、锑、砷、硒、钡和镍的溶出量。选择波长为216.9,228.8,267.7,194.2,206.8,189.0,196.0,455.4,216.6nm的9条谱线依次作为测定铅、镉、铬、汞、锑、砷、硒、钡和镍的分析线。铅、镉、铬、锑、砷、硒、钡和镍的质量浓度与其发射强度在10.0mg·L-1以内、汞在2.0mg·L-1以内呈线性关系,检出限(3s)在0.002～0.05mg·L-1之间。方法用于金属饰品的分析,回收率在95.4%～103.0%之间,测定值的相对标准偏差(n=11)在0.68%～2.0%之间。     

ICP-AES法测定玻璃器皿中铅、镉、砷、锑溶出量的研究

采用ICP-AES法同时测定玻璃器皿中铅、镉、砷、锑的溶出量,对ICP-AES法测定4％乙酸浸泡液时分析线的选择和射频功率、载气压力的影响,以及基体和共存离子的干扰情况等进行了研究。4种元素的检出限分别为铅0．012mg／L,镉0．0009mg／L,砷0．015mg／L,锑O．015mg／L,加标回收率为97．3％～102．0％,测定结果的相对标准偏差为0．45％～1．36％（n=6）.     

Biosorption of Lead,Copper, and Cadmium by <Emphasis Type="Italic">Phanerochaete chrysosporium</Emphasis> in Ternary Metal Mixtures: Statistical Analysis of Individual and Interaction Effects

Biosorption of three divalent metals, viz., lead, copper, and cadmium in ternary aqueous mixtures was studied using Phanerochaete chrysosporium in batch shake flasks. The mixtures were prepared containing the metals at their either varying optimum or equal initial concentration combinations in aqueous solution of pH optimum to each of the metals. Following were the optimum initial concentration ranges of the metals in mixture: lead, 60–100 mg/L; copper, 20–60 mg/L; and cadmium, 5–15 mg/L. And, for varying these optimum concentration levels of the metals, a 2³ full factorial design of experiments was employed. The results revealed that an increase in lead and cadmium concentrations helped in their better biosorption by the fungus, but an increase in initial copper concentration slightly diminished its removal. Statistical analysis of the results in the form of analysis of variance and Student t test gave a clear interpretation on the roles of both the individual metals and their interactions in the uptake of metals from mixture. Compared to the uptake of metals when presented individually, lead biosorption in mixture was found to be enhanced to a degree as high as 99%; on the other hand, copper and cadmium removals from mixtures were inhibited to the extent of 100% and 98%, respectively. However, this extent of inhibition or enhancement in the metal removals compared to the individual removals was less in mixtures containing all equal concentrations of the metals.     

Efficient Removal of Lead from Washing Effluent of Lead-contaminated Soil with Garlic Peel

Wastewater produced from the soil washing process contains heavy metals, which limits its reuse for washing. So it is necessary to develop an efficient and economical way to recycle it, and this study presented a biosorption method to realize this goal. A typical soil sample contaminated by lead was taken from the real field near a lead smelting factory, used for the toxic metals extraction with dilute citric acid. A leach liquor was obtained with lead ions at the level of 12.35 mg/L, Cd 1.2 mg/L, Cu 1.5 mg/L, Zn 2.6 mg/L, as well as the coexisting anions, such as sulphate, silicate, chloride at the concentration of several hundred miligram per liter. The garlic peel was modified by a simple chemical saponification process and used as the biosorbent for toxic metal removal. Firstly, the adsorption behavior of lead ions on the saponified garlic peel was systematically investigated using the synthetic solutions, and then the adsorption mechanisms were explored by detailed experiments combining with the thermodynamic calculation reuslts of the aqueous system of Pb(Ⅱ)-citrate-H₂O. It was found that in artificial solution containing 0.01 mol/L citrate, the maximum adsorption capacity of 261.0 mg/g was reached at pH near 3.0, and also at this very pH value the Pb²⁺ and Pb(H₂Cit)⁺ were the dominant lead species, which are favorable for adsorption due to its easier approaching to the -COO^- ligands in the saponified garlic peel partilces via charge attraction, and the appearance of Pb(HCit)⁰ and Pb(Cit)^- at pH above 3.0 inhibits the adsorption. Secondly, the real leach liquor was used for adsorption tests, and twice adsorption under the optimal conditons would decrease the residual concentrations of Pb, Cd, Cu and Zn to zero. After elution by using 0.1 mol/L nitric acid, the adsorbed metals can be recovered and garlic peel can be reused for at least 10 cycles effectively. This study presents a prospective biosorption method for economical and efficient removal of the lead ions from soil washing wastewater with citric acid as the leaching reagent.     

Application of Total Reflection X-Ray Fluorescence Spectrometry in the Textile Industry

 In the present study, the determination of arsenic, lead, cadmium, chromium, cobalt, copper, nickel, mercury and zinc in various cloth samples produced in Kayseri-Turkey was performed after extraction with artificial sweat solution and decomposition with nitric acid. TXRF is shown to be suitable for the determination of 7 trace elements, down to the 0.001 (cobalt) to 0.004 (copper) mg/kg level in textile extract except for mercury and cadmium. The extractable part of the toxic metals by artificial sweat solution is relatively low. In a few extracts the concentration values of Pb and Ni have exceeded their critical values of 0.2 mg/kg for lead and 1.0 mg/kg for nickel given by ?ko-Tex and determined for babys cloths. In addition, it was observed that the element pattern of textile samples resembled ‘finger print type’, TXRF-spectra. This technique can also be used for the identification of textile sample in forensic investigation. Received April 16, 2001 Revision October 1, 2001.     

能量色散X射线荧光光谱法测定中草药中的Cd元素

利用能量散射X射线荧光光谱（ED-XRF）法快速测定中草药中的Cd元素.方法对中草药进行简单预处理（粉碎）,使用X射线荧光光谱法建立中草药中Cd元素含量与相对强度的校正工作曲线,分析中草药样品中的Cd元素.Cd元素的检出限为0.083 mg/kg,定量限为0.207 mg/kg,定量限低于国家控制标准0.3 mg/kg.测量定量限以上的中草药样品时,其准确性与化学分析结果相当,重复性和稳定性等结果完全满足GB/T 4889-2008数据的统计处理标准.方法预处理时间不超过5 min,完成一个样品的检测时间不超过15 min,可应用于中草药生产企业中的重金属监控.     

Test method for the separate determination of mercury(II), cadmium, and lead in one sample on the fibrous sorbent PANV-AV-17

The sorption of Hg(II), Cd(II), and Pb(II) as anionic complexes on the solid phase of polyacrylonitrile fiber filled with the AV-17 anion exchanger from NaCl and KI solutions and their complexation with 4-(2-pyridylazo)resorcinol (PAR) and dithizone were studied. A test method was developed for the individual determination of Hg(II), Cd(II), and Pb(II) from one sample on three support disks. From the same solution, by the successive sorption on two disks from a 0.2 M NaCl solution, mercury was determined with dithizone and cadmium was determined with PAR. After the addition of a KI solution and sorption on the third disk, lead was determined with PAR. Using the added-found method, the procedure was approved in the analysis of natural sodium chloride water. The detection limit was 0.01 mg/L for Hg(II) and 0.02 mg/L for Cd(II) and Pb(II) for a volume of the analyzed sample of 25 mL. The time of the analysis of five or six samples (determination of three elements) is no longer than 50 min.     

Study of the selection mechanism of heavy metal (Pb2+, Cu2+, Ni2+, and Cd2+) adsorption on clinoptilolite

The study was carried out on the sorption of heavy metals (Ni2+, Cu2+, Pb2+, and Cd2+) under static conditions from single- and multicomponent aqueous solutions by raw and pretreated clinoptilolite. The sorption has an ion-exchange nature and consists of three stages, i.e., the adsorption on the surface of microcrystals, the inversion stage, and the moderate adsorption in the interior of the microcrystal. The finer clinoptilolite fractions sorb higher amounts of the metals due to relative enriching by the zeolite proper and higher cleavage. The slight difference between adsorption capacity of the clinoptilolite toward lead, copper, and cadmium from single- and multicomponent solutions may testify to individual sorption centers of the zeolite for each metal. The decrease of nickel adsorption from multicomponent solutions is probably caused by the propinquity of its sorption forms to the other metals and by competition. The maximum sorption capacity toward Cd2+ is determined as 4.22 mg/g at an initial concentration of 80 mg/L and toward Pb2+, Cu2+, and Ni2+ as 27.7, 25.76, and 13.03 mg/g at 800 mg/L. The sorption results fit well to the Langmuir and the Freundlich models. The second one is better for adsorption modeling at high metal concentrations.     

能量色散-X射线荧光光谱测定中草药痕量镉、铅、铜

为寻求一种能够直接对中草药中重金属进行快速检测的方法,采用压片法对样品进行前处理,建立了能量色散-X射线荧光光谱法快速检测中草药中痕量重金属镉、铅、铜元素的方法。在20 min即可完成检测,镉、铅、铜检出限分别为0.072、0.207、0.340 mg/kg,测试结果表明与原子吸收和ICP-MS相比,本方法数据稳定性和准确度良好,具有快速、准确、简单的优点,能够满足药典中对重金属元素的限量要求,适用于现场快速检测与质量控制检测。     

Heavy metal levels and physico--chemical quality of potable water supply in Warri, Nigeria

The interaction between man's activities and the environment is gaining world wide attention. Warri an oil producing community in Delta State of Nigeria is faced with environmental oil pollution. Since open and underground water bodies are regarded as final recipients of most environmental pollutants, this study sought to provide data on the levels of the physico-chemical parameters and contaminants in Warri metropolitan water supply. This study investigated the cadmium, lead and chromium using Atomic Absorption Spectrophotometer, physico-chemical properties such as pH, temperature, total suspended solid TSS, total dissolved solid TDS, electrical conductivity EC, biological oxygen demand BOD, dissolved oxygen DO, chemical oxygen demand COD, and total coliform count of potable water sources in Warri. Ekpan River was found to have 1.2 mg/L of cadmium, 1.0 mg/L of chromium, 1.20 mg/L of lead and 2.0 mg/L of manganese. The heavy metals levels and the pollution parameters were lowest in the borehole water samples, except pH which is more acidic in borehole water samples and conductivity which is more in well water samples in all the sampling stations. Some of the parameters were above WHO standards.     

Kinetic, equilibrium and thermodynamic studies of cadmium (II) adsorption by modified agricultural wastes

Agricultural wastes have great potential for the removal of heavy metal ions from aqueous solution. The contamination of water by toxic heavy metals is a worldwide environmental problem. Unlike organic pollutants, the majority of which are susceptible to biological degradation, heavy metals do not degrade into harmless end products. Discharges containing cadmium, in particular, are strictly controlled because of the highly toxic nature of this element and its tendency to accumulate in the tissues of living organisms. This work aims to develop inexpensive, highly available, effective metal ion adsorbents from natural wastes as alternatives to existing commercial adsorbents. In particular, Tamrix articulata wastes were modified chemically by esterification with maleic acid to yield a carboxyl-rich adsorbent. The adsorption behavior of treated Tamrix articulata wastes toward cadmium ions in aqueous solutions in a batch system has been studied as a function of equilibration time, adsorbent dose, temperature and pH. Results showed that the maximum adsorption capacity was 195.5 mg/g in a pH 4 solution at 30 °C with a contact time of 120 min, an initial concentration of 400 mg/L and an adsorbent dose of 0.3 g/L. The kinetic data were analyzed using pseudo-first-order and pseudo-second-order kinetic models. It was shown that the adsorption of cadmium could be described by a pseudo-second-order equation. The experimental data were also analyzed using the Langmuir and Freundlich models of adsorption. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° have been evaluated and it has been found that the sorption process was spontaneous and exothermic in nature. From all of our data, we conclude that the treated Tamrix articulata wastes investigated in this study showed good potential for cadmium removal from aqueous solutions.