二苯胺磺酸钠还原法制备粒径可控的金纳米粒子

采用二苯胺磺酸钠还原四氯合金酸的方法,在室温条件下,用SDS(十二烷基硫酸钠)、SDBS(十二烷基苯磺酸钠)作表面活性剂,成功地合成了金纳米粒子.分别讨论了还原剂二苯胺磺酸钠、表面活性剂(SDS、SDBS)及四氯台金酸的浓度等对金纳米粒子的粒径和形貌的影响.通过控制反应条件,可以合成出平均粒径大约为10、14、30、36nm的金纳米粒子.利用透射电镜(TEN)、紫外-可见(UV-Vis)吸收光谱对金纳米粒子进行了表征.研究结果表明不同的SDS或SDBS/HAuCl4的摩尔比,对金纳米粒子的尺寸大小有影响.     

一步湿化学法合成超细金纳米线

以氯金酸(HAuCl₄)为前驱物, 油胺同时作为溶剂、表面稳定剂和还原剂, 通过简单的一步湿化学法合成超细金纳米线. 制备出的超细金纳米线不仅产量高、纯度高, 而且纵横比大, 纳米线平均直径~2 nm, 长度可达数十微米. 如果添加另一种还原剂油酸并调节油胺和油酸的体积比为1:1, 将生成直径为~9 nm的金纳米线. 通过改变反应温度和还原剂用量, 对该种超细金纳米结构的生长机制进行阐述说明: 以油胺为模板, 在油胺和一价金卤化物(AuCl)亲金键合形成的一维聚合链作用下, 被还原的金原子附着在已成核颗粒表面, 一维地生长成超细金纳米线.     

金纳米粒子的阳光光化学合成和晶种媒介生长

在柠檬酸盐-HAuCl4溶液体系中, 于高原太阳紫外线辐射下光化学合成了分散良好、尺寸分布窄的胶体金纳米粒子. 研究了溶液的酸度和太阳辐射条件对Au(Ⅲ)离子光化学还原反应速率和形成金纳米粒子尺寸的影响; 采用晶种媒介生长技术, 通过改变Au(0)/Au(Ⅲ)比合成了平均直径为4.9~9.7 nm的球形金粒子. 根据紫外-可见吸收光谱和透射电子显微镜的表征和分析, 讨论了光化学反应中自由基反应、金纳米粒子成核和生长机理.     

金纳米粒子组装体的连续离散型纳米结构控制

采用柠檬酸钠还原氯金酸的方法,制备出粒径均一的金纳米粒子(AuNPs),通过加入二水合双(对-磺酰苯基)苯基膦化二钾盐(BSPP),增强了AuNPs体系的分散性与稳定性.选用直径为15和40nm的AuNPs,用不同序列巯基修饰的单链DNA连接到其表面,通过DNA链的杂交,形成不同结构的金纳米粒子组装体.通过改变加入DNA延长连接单元的比例,可以控制金纳米粒子组装体具有连续离散型的1∶1,2∶1和3∶1纳米结构.     

以C60为媒介的网状金纳米粒子聚集体的构筑

通过全甲基化环糊精和卟啉之间的"Click"反应,合成了一种不对称环糊精修饰的卟啉衍生物,并对其结构进行了表征.该化合物与氯金酸作用可以形成平均粒径为5 nm的水溶性金纳米粒子,该金纳米粒子进一步与C60作用形成网状纳米聚集体,并通过紫外光谱和透射电子显微镜验证了聚集体的结构.     

种子数密度控制的Au@SiO2纳米粒子的合成

在异丙醇介质中用Frens金溶胶作种子介导合成二氧化硅包覆金(Au@SiO2)纳米粒子.研究结果表明,单核Au@SiO2纳米粒子的产率取决于催化剂用量、硅源加入速率及种子数密度.通过种子数密度控制,合成了高度单分散的粒径为200,320和450 nm的Au@SiO2纳米粒子,以期用作功能材料的理想构筑单元.     

以SDS-PEG团簇为软模板在温和条件下合成金纳米环

介绍一种由十二烷基硫酸钠(SDS)与聚乙二醇(PEG 20000)组成的团簇为软模板, 在室温、常压、无硬模板及无外加还原剂条件下自还原HAuCl₄合成金纳米环的新方法. TEM显示合成的金纳米环的直径为(500±50) nm; UV-vis光谱显示在800 nm以上区域有强吸收带, 证明有大的各向异性的纳米结构生成. 电子衍射(ED)显示合成的金纳米环为金单晶结构; XRD显示金纳米环的(200)与(111)衍射峰的强度比(I₍₂₀₀₎/I₍₁₁₁₎)为0.11, 比反应初始阶段的0.31降低0.2左右, 表明金纳米结构主要为(111)晶面取向. TEM和SEM跟踪显示, 金纳米环的生长经历了从金纳米球到纳米片再到纳米环的变化过程, 控制反应时间可以得到预期的金纳米结构.     

光化学合成Au核@Pd壳复合纳米粒子及其表征

在PEG-丙酮溶液体系中, 采用紫外光辐射还原Au(Ⅲ), Pd(Ⅱ)离子混合物和以Au晶种为核、紫外光辐射还原Pd(Ⅱ)使其沉积在Au晶种表面上这两种方法, 合成了Au核@Pd壳复合纳米粒子. 通过改变Au(Ⅲ)离子或Au晶种对Pd(Ⅱ)离子的摩尔比调节复合粒子的尺寸和Pd壳厚度, 分别获得了直径范围为5.6~4.6 nm和4.6~6.2 nm的复合粒子. 利用UV-Vis吸收光谱、TEM、HR-TEM和XPS等表征手段, 证明了合成的纳米粒子为核-壳复合结构. 研究了Au@Pd纳米粒子的直径随溶液中Au(Ⅲ)/Pd(Ⅱ)摩尔比的改变而变化的规律; 对Au核向Pd壳的供电子作用以及复合粒子的光化学形成机理进行了讨论.     

嵌段聚合物修饰的金纳米粒子的制备及表征

通过RAFT合成聚(甲基丙烯酸缩水甘油酯)-b-聚(乙二醇甲基丙烯酸酯)嵌段共聚物(PGMA-bPMAPEG),再用半胱氨酸(Cys)使PGMA中的环氧基团开环,制备含有巯基的两亲水嵌段聚合物PMAPEG-bP(GMA-Cys)。并以其作为修饰剂,通过原位还原法使HAuCl4在NaBH4的还原下制备金/聚合物纳米复合粒子(Au@PMAPEG-b-P(GMA-Cys)NPs)。经FT-IR、UV-vis、TG、XRD、TEM和DLS表征,发现金纳米复合粒子呈均匀分散的球形,平均粒径约为10nm,在527nm处出现了金纳米粒子的表面等离子共振吸收峰,金约占总重量的49%。由于外层嵌段共聚物的修饰作用,金纳米复合粒子在室温下放置6个月未发生粒子间的聚集。     

基底对电沉积制备ZnO纳米棒阵列的影响

采用恒电位电沉积方法, 在未经修饰的ITO导电玻璃基底上通过控制实验条件制备出不同形貌的纳米ZnO结构, 而在经过ZnO纳米粒子膜修饰后的ITO导电玻璃基底上, 制备出透明、高取向、粒径小于30 nm的ZnO纳米棒阵列. 用扫描电子显微镜(SEM)、X射线衍射(XRD)以及透射光谱对制备出的ZnO纳米棒阵列的结构、形貌和透明性进行了表征. 测试结果表明, ZnO纳米棒阵列的平均直径为21 nm, 粒径分布窄, 约18～25 nm, 择优生长取向为[001]方向, 垂直于基底生长. 当入射光波长大于400 nm时, ZnO纳米棒阵列的透光率大于95%.     

Metal and Metal Oxide Nanostructures Prepared by Electrical Arc Discharge Method in Liquids

In this review, the importance of electrical arc discharge technique in liquids in synthesis of various nanostructures from carbon based materials to metal and metal oxide nanostructures with their general and specific properties, especially the photocatalytic performance of metal oxide nanostructures is studied. The effect of arc current on size distribution, morphology and physicochemical properties of metal and semiconductor nanostructures was investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic light scattering (DLS), X-ray photoelectron spectroscopy (XPS) and UV–Vis spectroscopy. WO₃ Cubic nanostructures with 30 nm mean particle size were formed during the discharge process in water. Discharge between zinc electrodes in water leads to formation of rod like and semi spherical ZnO nanostructures with 15–20 nm diameter range. ZrO₂ nanoparticles were formed using zirconium electrodes in water. Photodegradation of Rhodamine B (Rh. B) shows that the as prepared nanostructures in this method have potential ability for environmental purifications. Also, using silver electrodes in water leads to formation of silver nanoparticles with 8–15 nm average particle size. Moreover, a novel method for synthesis of gold nanoparticles without using gold electrodes is presented. Finally, the future outlook of this technique in synthesis of various nanocrystalline materials is presented.     

Use of ionic liquids in the synthesis of nanocrystals and nanorods of semiconducting metal chalcogenides

We have synthesized nanoparticles of hexagonal CdS in the diameter range 3-13 nm by the reaction of cadmium acetate dihydrate with thioacetamide in imidazolium [BMIM]-based ionic liquids. We have obtained three different particle sizes of CdS by changing the anion of the ionic liquid. Addition of trioctylphosphine oxide (TOPO) to the reaction mixture causes greater monodispersity as well as smaller particle size, while addition of ethylenediamine produces nanorods of 7 nm average diameter. Hexagonal ZnS and cubic PbS nanoparticles with average diameters of 3 and 10 nm, respectively, have been prepared by the reaction of the metal acetates with thioacetamide in [BMIM][BF4]. Hexagonal CdSe nanoparticles with an average diameter 12 nm were obtained by the reaction of cadmium acetate dihydrate with dimethylselenourea in [BMIM][BF4]. In this case also we observe the same effect of the addition of TOPO as in the case of CdS. Addition of ethylenediamine to the reaction mixture gives rise to nanorods. ZnSe nanowires with a cubic structures, possible diameters in the range 70-100 nm by the reaction of zinc acetate dihydrate with dimethylselenourea in [BMIM][MeSO4]. The nanostructures obtained are single crystalline in all the cases. Most of the nanostructures show characteristic UV/Vis absorption and photoluminescence emission spectra. The thermodynamically most stable structures are generally produced in the synthesis carried out in ionic liquids.     

Photofragmentation of phase-transferred gold nanoparticles by intense pulsed laser light

Gold nanoparticles with an average diameter of approximately 20 nm were prepared in an aqueous solution by a wet chemistry method. The parent gold nanoparticles were then capped with a 4-aminothiophenol protecting layer and transferred into toluene by tuning the surface charge of the modified nanoparticles. Gold nanoparticles before and after phase transfer were subjected to photofragmentation by a pulsed 532 nm laser. The effects of solvent properties and surface chemistry on the photofragmentation of the gold nanoparticles have been investigated. Fast photofragmentation has been observed in the organic solvent in which the dielectric constant, heat capacity, and thermal conductivity are lower. The results suggest new approaches for the preparation of very small gold clusters from gold nanoparticles.     

Extinction coefficient of gold nanoparticles with different sizes and different capping ligands

Extinction coefficients of gold nanoparticles with core size ranging from approximately 4 to 40 nm were determined by high resolution transmission electron microscopy analysis and UV-vis absorption spectroscopic measurement. Three different types of gold nanoparticles were prepared and studied: citrate-stabilized nanoparticles in five different sizes; oleylamide-protected gold nanoparticles with a core diameter of 8 nm, and a decanethiol-protected nanoparticle with a diameter of around 4 nm. A linear relationship between the logarithms of extinction coefficients and core diameters of gold particles was found independent of the capping ligands on the particle surface and the solvents used to dissolve the nanoparticles. This linear relation may be used as a calibration curve to determine the concentration or average size of an unknown nanoparticle or nanoparticle-biomolecule conjugate sample.     

Synthesis of gold nanoparticles by microemulsion assisted photoreduction method

A new, clean, cost-effective and rapid method for the synthesis of stable spherical gold nanoparticles (AuNPs) is developed. This novel technique combines microemulsion as one of soft-nanotechnology techniques of wet chemistry, with photo-physics of UV-radiation in a unique versatile method to design and obtain controlled nanostructures for multifunctional materials. Based on a phase diagram in ternary water/Brij 30/n-heptane system pristine, and thiol functionalized, gold nanoparticles were obtained by a microemulsion assisted photoreduction technique, allowing increased flexibility during the synthesis and selection of materials. The spherical nanoparticles obtained by this route show a homogeneous size distribution, with an average diameter of 11 nm, for pristine gold nanoparticles and of 12 nm, for functionalized species. The evolution of the system at the nanoscale has been studied using, in tandem, UV-VIS and DLS measurements. The structure, size and shape of the final nanoparticles obtained have been evaluated by adequate instrumental techniques: FTIR, XRD and TEM image analysis. Kinetic studies have also been performed in order to follow the evolution of nanospecies during irradiation procedure.     

Metallic mesoporous nanocomposites for electrocatalysis

We describe the fabrication, characterization, and applications of ultrathin, free-standing mesoporous metal membranes uniformly decorated with catalytically active nanoparticles. Platinum-plated nanoporous gold leaf (Pt-NPG) made by confining a plating reaction to occur within the pores of dealloyed silver/gold leaf is 100 nm thick and contains an extremely high, uniform dispersion of 3 nm diameter catalytic particles. This nanostructured composite holds promise as a prototypical member of a new class of fuel cell electrodes, showing good electrocatalytic performance at low platinum loading (less than 0.05 mg cm-2), while also maintaining long-term stability against coarsening and aggregation of catalytic nanoparticles.     

Uniform arrays of gold nanoparticles with different surface roughness for surface enhanced Raman scattering

Uniform arrays of coarse and smooth gold nanoparticles with diameter about 130 nm were successfully synthesized through seed-mediated growth method, separately. Scanning and transmission electron microscopy (SEM and TEM) and X-ray diffraction (XRD) have been used to study the formation and structure of the nanocomposites. The high enhancement factor for surface-enhanced Raman scattering of coarse and smooth gold nanoparticles were estimated to be about 3.1 × 10⁶ and 2.0 × 10⁶, respectively. It is evident that the coarse gold nanostructures has higher influence factor than the smooth gold nanostructures. Therefore, these unique properties of the coarse Au nanoparticles appear to be very promising for applications as high-performance SERS substrates.     

Ultrathin gold nanoframes through surfactant-free templating of faceted pentagonal silver nanoparticles

Ultrathin gold nanoframes (up to 1.6 nm) were prepared via templating upon well-defined faceted silver morphologies. Starting with silver decahedra, small quantities of gold (1-10 mol% relative to the amount of silver) were selectively deposited on the nanoparticle edges under optimized reducing conditions. Silver dissolution in hydrogen peroxide yielded well-defined gold frames that retained their structural integrity in the ultrathin nanowire regime below 2 nm. The frame formation protocol was also successfully applied to other silver nanoparticle shapes featuring pentagonal twinning and (111) facets (e.g., pentagonal faceted rods and icosahedra). The demonstrated approach can be applied in the controlled preparation of ultrathin metal nanowires complementary to lithography and in the production of ultrafine noble-metal nanostructures for catalytic applications.     

Growth and characterization of highly branched nanostructures of magnetic nanoparticles

Magnetite nanoparticles of Fe(3)O(4) have been found to grow into large highly branched nanostructures including nanochains and highly branched nanotrees in the solid state through a postannealing process. By varying the preparation conditions such as annealing time and temperature, the nanostructures could be easily manipulated. Changing the starting concentration of the magnetic nanoparticle solution also caused significant changes of the nanoarchitectures. When the magnetic nanoparticle concentration is low, the nanoparticles formed straight rods mainly with an average diameter of 80 nm and a length of several microns. With increasing concentration of the nanoparticles, treelike structures began to form. With further increase of the concentration, well-ordered nanostructures with the appearance of snowflakes were generated. The driving force for the formation of the highly ordered nanostructures includes interaction between the nanoparticles and interaction through surface-capping molecules. This experiment demonstrates that novel nanostructures can be generated by self-assembly of magnetic nanoparticles under the solid state.     

Silica-void-gold nanoparticles: temporally stable surface-enhanced Raman scattering substrates

Reproducible detection of a target molecule is demonstrated using temporally stable solution-phase silica-void-gold nanoparticles and surface-enhanced Raman scattering (SERS). These composite nanostructures are homogeneous (diameter = 45 +/- 4 nm) and entrap single 13 nm gold nanoparticle cores inside porous silica membranes which prevent electromagnetic coupling and aggregation between adjacent nanoparticles. The optical properties of the gold nanoparticle cores and structural changes of the composite nanostructures are characterized using extinction spectroscopy and transmission electron microscopy, respectively, and both techniques are used to monitor the formation of the silica membrane. The resulting nanostructures exhibit temporally stable optical properties in the presence of salt and 2-naphthalenethiol. Similar SERS spectral features are observed when 2-naphthalenethiol is incubated with both bare and membrane-encapsulated gold nanoparticles. Disappearance of the S-H Raman vibrational band centered at 2566 cm(-1) with the composite nanoparticles indicates that the target molecule is binding directly to the metal surface. Furthermore, these nanostructures exhibit reproducible SERS signals for at least a 2 h period. This first demonstration of utilizing solution-phase silica-void-gold nanoparticles as reproducible SERS substrates will allow for future fundamental studies in understanding the mechanisms of SERS using solution-phase nanostructures as well as for applications that involve the direct and reproducible detection of biological and environmental molecules.