电化学还原的氧化石墨烯修饰电极检测L-色氨酸

制备了氧化石墨烯修饰玻碳电极,并运用循环伏安法对氧化石墨烯进行了直接的电化学还原,研究了L-色氨酸在该电化学还原的氧化石墨烯修饰玻碳电极上的电化学行为。结果表明,L-色氨酸在该修饰电极上其氧化峰电流与裸玻碳电极相比增大了7.1倍,且峰电位负移80mV。利用差分脉冲伏安法,在pH=6.5的磷酸盐缓冲溶液中测定L-色氨酸,氧化峰电流与其浓度在0.4～65.0μmol/L范围内呈良好的线性关系,相关系数为0.998,方法检出限为0.2μmol/L。     

抗坏血酸在石墨烯微片修饰玻碳电极上的电化学行为及其测定

基于石墨烯微片修饰玻碳电极对抗坏血酸的电催化作用,建立了测定抗坏血酸的电化学分析方法。石墨烯微片修饰玻碳电极与裸玻碳电极相比,显著提高了抗坏血酸的氧化峰电流,降低了氧化峰电位,提高了测定的灵敏度。该电极测定抗坏血酸的线性范围为5.0×10-5～2.5×10-2mol/L,最低检测限为6.5×10-7mol/L(信噪比=3)。     

基于石墨烯修饰电极测定蔬菜中残余对硫磷的研究

制备了石墨烯薄膜修饰玻碳电极,并通过循环伏安法研究了对硫磷(PT)在该修饰电极上的电化学行为。对支持电解质、溶液pH值等实验条件进行了优化。结果表明,在0.1mol/L的乙酸-乙酸钠缓冲溶液(pH=5.0)中,PT在石墨烯薄膜修饰电极上具有良好的电化学响应,对比裸玻碳电极,PT的氧化峰峰电流显著提高,表明修饰膜对PT的电化学氧化具有一定的催化作用。PT的氧化峰电流及其浓度分别在1.0×10-7~1.0×10-6 mol/L范围内和3.0×10-6~1.0×10-5 mol/L范围内呈良好的线性关系,线性相关系数分别是0.9956和0.9874,检出限为1.0×10-8 mol/L。将该修饰电极应用于小白菜中残留PT的测量,结果比较满意。     

一种基于乙炔黑/壳聚糖膜修饰电极的对氨基酚传感研究

制备了一种乙炔黑/壳聚糖薄膜修饰的玻碳电极,用循环伏安法详细研究了对氨基酚在该修饰电极上的电化学行为.结果表明: 对氨基酚在此膜修饰电极上呈现出一对可逆的氧化还原峰.相对于裸玻碳电极,该氧化还原峰的峰电流明显提高,峰电位差减小,可逆性变好,表明乙炔黑/壳聚糖薄膜电极对对氨基酚的电化学氧化具有良好的催化作用.对氨基酚的氧化峰电流与其浓度在1.0×10-7～2.0×10-6 mol/L和2 0×10-6～5.0×10-4 mol/L范围内均呈良好的线性关系; 检出限为5.0×10-8 mol/L(S/N=3).应用此修饰电极测定实际水样,结果较满意.     

聚组氨酸/石墨烯修饰玻碳电极测定曲克芦丁

将石墨烯涂覆在玻碳电极表面,制备了石墨烯/玻碳电极(Gr/GCE)。用循环伏安法(Cyclic voltammetry,CV)将组氨酸修饰在石墨烯/玻碳电极表面,制成了聚组氨酸/石墨烯玻碳电极(polyHiS/Gr/GCE)。用该修饰电极对曲克芦丁水解物进行电化学检测,实验表明,在最优条件下,该修饰电极对曲克芦丁水解物有显著的电催化作用,其氧化峰电流与其浓度在2.0×10-6~4.0×10-4mol·L-1范围内呈良好的线性关系,相关系数为R=0.9996,检出限为1.25×10-6mol·L-1。此方法可应用于实际样品的测定。     

镉在羧基化石墨烯电极上的电化学研究

本实验制备了羧基化的氧化石墨烯,并将其修饰在玻碳电极(GCE)表面制备了羧基化石墨烯/玻碳电极(GO-COOH/GCE),以此为工作电极研究了镉在GO-COOH/GCE上的电化学行为及测定方法。与裸玻碳电极(GCE)相比,GO-COOH膜修饰玻碳电极能显著加强镉的氧化还原峰电流。在pH=4.5的NaAc-HAc缓冲溶液中,镉在GO-COOH/GCE电极上出现1组氧化还原峰,Epa=-0.81 V,Epc=-0.93 V,△E=0.12 V;ipa=8.04μA,ipc=8.54μA,ipa/ipc=0.94。氧化峰电流与Cd2+浓度在5.5×10-7～7.5×10-6g.L-1(r=0.9969)范围内呈良好的线性关系,检出限为2.0×10-7g.L-1。实际样品测定的RSD为1.2%(n=5),平均回收率为101.3%。GO-COOH膜对镉的电化学氧化有明显的催化作用,本法是一种可靠、快捷、灵敏的检测方法,可以用于保健品螺旋藻药片中镉含量的测定。     

纳米金/三聚氰胺修饰电极检测亚硝酸盐

采用电聚合方法制备三聚氰胺(MA)膜修饰玻碳电极(GCE),然后采用原位恒电位沉积法制备金纳米颗粒(Au),并将其修饰于膜电极表面,制得纳米金/三聚氰胺修饰玻碳电极(Au/MA/GCE)。用扫描电子显微镜(SEM)对修饰电极进行表面形貌和元素成分分析。用循环伏安法研究亚硝酸根(NO2-)在该修饰电极上的电化学行为发现,NO2-在0.85 V出现一灵敏的氧化峰。在优化的实验条件下,NO2-在1.0×10-5～1.0×10-3mol/L浓度范围内与其氧化峰电流成线性关系,检测下限为8.9×10-7mol/L。将修饰电极用于实际样品中NO2-的检测,效果良好。     

石墨烯/聚硫堇膜修饰玻碳电极上沙丁胺醇的电化学行为研究

采用循环伏安法和差分脉冲伏安法研究了沙丁胺醇在石墨烯/聚硫堇修饰玻碳电极上的电化学行为,该电化学传感器对沙丁胺醇显示出良好的电化学响应。在pH 7.0,扫描范围为-0.6~0.4 V,扫速为80 mV/s条件下,沙丁胺醇的氧化峰电流与其浓度在3.1×10-7~8.5×10-5mol/L范围内呈良好线性关系,检出限达9.6×10-8mol/L。结果显示石墨烯/聚硫堇修饰玻碳电极具有良好的重现性和稳定性。     

聚天青I/石墨烯修饰电极的电化学行为及对亚硝酸根的检测

制备了聚天青I/石墨烯修饰玻碳电极。用循环伏安法研究了溶液pH,扫描速率对聚天青I/石墨烯修饰电极的电化学行为的影响及修饰电极对NO-2的电催化作用。利用示差脉冲伏安技术检测NO-2,NO-2浓度在1.0×10-7~1.0×10-5mol/L的范围内,其氧化峰电流与浓度呈现良好的线性关系,检出限为3.7×10-8mol/L(S/N=3)。修饰电极已用于水体中NO-2的检测。     

聚拉莫三嗪膜修饰玻碳电极的电化学行为及电催化性能研究

研究了拉莫三嗪在玻碳电极上的电化学修饰及其修饰电极的电化学行为.在H2SO4介质中,采用循环伏安法制备了聚拉莫三嗪膜修饰玻碳电极(PLTG/GCE),用交流阻抗技术对修饰层进行表征.研究发现,该电极对NO-2具有明显的电催化氧化作用和灵敏的电流响应,NO-2的氧化峰电流与其浓度在9.6×10-6 ～ 1.1×10-3 ...     

镍钴双金属-卟啉有机框架复合纳米材料构建的无酶传感器检测多巴胺

以Ni、Co为金属节点,5,10,15,20-四（4-羧基苯基）卟啉（TCPP）为金属配体,合成了金属有机框架材料（MOFs）作催化材料,以还原氧化石墨烯（rGO）和乙炔黑（ACET）作信号放大材料,制备出一种灵敏度高、稳定性高、选择性好的无酶电化学传感器,用于检测多巴胺（DA）。通过一步水热法制成rGO-NiCoTCPP,再用滴涂法将其修饰在玻碳电极上,即得GCE/rGO-NiCoTCPP电极,最后将ACET滴涂在此电极上,得到GCE/rGO-NiCoTCPP/ACET电极。利用红外光谱、扫描电子显微镜和电化学阻抗对此电极进行了表征,并将不同修饰电极放在磷酸缓冲液中进行循环伏安表征。GCE/rGO-NiCoTCPP/ACET传感器对DA具有较宽线性范围（0.4 ~160 μmol/L）及较高的电流响应（检出限为0.198 μmol/L）,有望应用于实际样品中DA的检测。     

A Sensitive and Selective Nitrite Detection in Water Using Graphene/Platinum Nanocomposite

A glassy carbon electrode modified with reduced graphene oxide and platinum nanocomposite film was developed simply by electrochemical method for the sensitive and selective detection of nitrite in water. The electrochemical reduction of graphene oxide (GO) efficiently eliminates oxygen‐containing functional groups. Pt nanoparticles were electrochemically and homogeneously deposited on the ErGO surface. Field emission scanning electron microscopy (FE‐SEM), Raman spectroscopy, attenuated total reflectance‐fourier transform infrared spectroscopy (ATR‐FTIR), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) were used to examine the surface morphology and electrocatalytic properties of the Pt‐ErGO nanocomposite film‐modified electrode surface. The fabricated nitrite sensor showed good electrochemical performance with two linear ranges; one from 5 to 100 µM (R²=0.9995) and the other from 100 to 1000 µM (R²=0.9972) and a detection limit of 0.22 µM. The proposed sensor was successfully applied for the detection of nitrite in tap water samples which proves performance of the Pt‐ErGO nanocomposite films.     

二氧化锆/石墨烯复合材料对亚硝酸盐的电化学传感研究

制备了一种二氧化锆/还原氧化石墨烯(ZrO2NPs/rGO)复合材料修饰电极的亚硝酸盐电化学传感器,并成功用于亚硝酸盐的检测.采用循环伏安法和电流-时间曲线考察了修饰电极的电化学行为.实验结果表明,ZrO2NPs/rGO复合材料修饰电极对亚硝酸盐具有良好的电流响应.在最优实验条件下,电流-时间曲线中的电流响应信号与亚硝酸盐浓度在3.0×10Symbolm@@_7～1.0×10Symbolm@@_6 mol/L和1.0×10Symbolm@@_6～6.0×10Symbolm@@_6 mol/L的范围内呈良好的线性关系,检测限为1.0×10Symbolm@@_7 mol/L(S/N 3).该传感器灵敏性高、稳定性和重现性好.使用此传感器检测实际样品香肠中的亚硝酸盐的回收率为93.7％～110.4％,相对标准偏差为1.6％～2.1％.     

A novel nitrite sensor based on graphene/polypyrrole/chitosan nanocomposite modified glassy carbon electrode

A novel nitrite sensor was fabricated based on a graphene/polypyrrole/chitosan nanocomposite film modified glassy carbon electrode. The nanocomposite film was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy and Raman spectroscopy. The electron transfer behaviour of the modified electrodes was investigated in [Fe(CN)(6)](3-)/(4-) redox probe using cyclic voltammetry and electrochemical impedance spectroscopy. Differential pulse voltammetry and amperometry were used to study the electrochemical properties of the proposed sensor. Under optimum conditions, the sensor exhibited good reproducibility and stability for nitrite determination. Linear response was obtained in the range of 0.5-722 μM with a detection limit of 0.1 μM (S/N = 3) for nitrite determination.     

三维还原氧化石墨烯/β-环糊精复合物的合成及其电化学检测水中左氧氟沙星北大核心CSCD

成功构筑了β-环糊精修饰的三维还原氧化石墨烯复合材料(3D-rGO/β-CD),并对该复合材料进行扫描电子显微镜、傅里叶红外光谱、热重分析和拉曼光谱分析等一系列的表征,分析了其形貌和结构的特征。进一步将其修饰到玻碳电极(GCE)表面,构建了一种新型电化学传感器(3D-rGO/β-CD/GCE)。利用3D-rGO/β-CD/GCE电化学传感器,通过微分脉冲伏安法(DPV)对左氧氟沙星(LEV)进行了检测。其中,具有多孔结构的三维还原氧化石墨烯具有优异的导电性能、比表面积大、化学稳定性好等优良的性质,而修饰的β-环糊精能在其环形腔内与客体分子结合形成超分子包合物,进而可以对LEV进行有效识别。研究结果显示,在最优实验条件下,3D-rGO/β-CD/GCE对左氧氟沙星的检测具有较宽的线性范围(1~150μmol/L),且检测限可达0.33μmol/L,同时该修饰电极还表现出良好的选择性和稳定性。此外,成功将其应用于实际水样中LEV的检测,表明该传感器具有一定的应用潜力。     

用磷钨杂多酸-聚吡咯-氧化铝薄膜修饰玻碳电极测定废水中的对苯二酚

利用草酸电解液一步阳极氧化法在高纯铝表面制得纳米孔阳极氧化铝(AAO)薄膜;随后通过纳米孔阳极氧化铝模板电聚合,将磷钨杂多酸(PW12)掺杂吡咯(Py)溶液修饰到玻碳电极(GCE)表面,制得高灵敏的纳米微粒修饰电极(PW12-PPy/AGCE);研究了PW12-PPy/AGCE的伏安行为,考察了其影响因素;并将该电极应用于废水中对苯二酚的测定.结果表明,所制备的PW12-PPy/AGCE可以用于测定废水中的对苯二酚.     

Thionine-functionalized graphene oxide,new electrocatalyst for determination of nitrite

In this work, thionine (Th) was assembled on the surface of graphene oxide as an electron transfer mediator using diazonium reaction (Th–GO). Then, Th–GO was characterized by different methods such as scanning electron microscopy, transmission electron microscopy, and Fourier transform infrared spectroscopy. Afterward, Th–GO was used for the modification of carbon paste electrode. Several electrochemical methods including cyclic voltammetry, differential pulse voltammetry, and hydrodynamic amperometry were used to investigate the behavior of the modified electrode. Then, the role of the modified electrode for oxidation of nitrite has been studied. For this purpose, the effect of critical experimental parameters including step potential and pulse amplitude (in differential pulse voltammetry technique), applied potential, the rotating speed of the disk (in amperometry technique), and the solution pH was investigated. Under the optimized conditions, the currents were found to be linear with the nitrite concentration in the range 0.05–33.0 and 0.5–800 µmol L^?1 with detection limits of 0.02 and 0.2 µmol L^?1 using differential pulse voltammetry and hydrodynamic amperometry, respectively. The introduced modified electrode showed good repeatability (RSD% = 3.2) and reproducibility (RSD% = 4.7). This electrochemical sensor was exerted successfully for the determination of nitrite and nitrate in real samples including water and wastewater samples.     

DNA／聚（3-甲基噻吩）复合膜修饰电极的制备及其应用于研究8-羟基-2＇-脱氧鸟嘌呤核苷的伏安行为及测定

首先通过电聚合方法在玻碳电极表面制备了聚（3-甲基噻吩）（P3MT）修饰膜,然后在一定电位下将DNA分子电沉积到P3MT表面,制备了DNA／（P3MT）复合膜修饰玻碳电极．研究了8-羟基-2’-脱氧鸟嘌呤核苷（8-OH-dG）在该复合膜修饰电极上的伏安行为以及扫描速度、pH值和尿酸对其伏安行为和检测的影响．实验结果表明,该复合膜修饰电极结合了P3MT和DNA两者的优点,使8-OH-dG在复合膜修饰电极上的电化学行为明显改善,而且具有很好的重现性和稳定性．在0．1mol／LpH7．0的磷酸盐缓冲溶液（PBS）中,8-OH-dG的氧化峰电流与其浓度在0．28～4．2μmol／L和4．2～19．6μmol／L两个范围内成良好的线性关系,检出限为56nmol／L（S／N=3）．该研究可以为制备HPLC或毛细管电泳电化学检测器检测8-OH—dG打下一定的基础,因此在检测尿样中8-OH-dG的研究方面具有潜在的应用价值．     

Bio-electrocatalysis of NADH and ethanol based on graphene sheets modified electrodes

Characterization and application of graphene sheets modified glassy carbon electrodes (graphene/GC) have been presented for the electrochemical bio-sensing. A probe molecule, potassium ferricyanide is employed to study the electrochemical response at the graphene/GC electrode, which shows better electron transfer than graphite modified (graphite/GC) and bare glassy carbon (GC) electrodes. Based on the highly enhanced electrochemical activity of NADH, alcohol dehydrogenase (ADH) is immobilized on the graphene modified electrode and displays a more desirable analytical performance in the detection of ethanol, compared with graphite/GC or GC based bio-electrodes. It also exhibits good performance of ethanol detection in the real samples. From the results of electrochemical investigation, graphene sheets with a favorable electrochemical activity could be an advanced carbon electrode materials for the design of electrochemical sensors and biosensors.     

大尺寸石墨烯量子点组装体的制备及电化学发光性能

对氧化石墨烯纳米材料进行HNO₃氧化处理, 制备了水溶性好且具有强电化学发光(ECL)活性的大尺寸石墨烯量子点组装体(Large-sized graphene quantum dot assemblies, LSGQD-NAs). 利用透射电子显微镜(TEM)、 原子力显微镜(AFM)、 傅里叶变换红外光谱(FTIR)和拉曼光谱(Raman)等方法对其进行了表征, 结果表明, 石墨烯量子点组装体的平均高度为20 nm, 且富含大量的羟基和羧基. 电化学测试结果显示, 在共反应物K₂S₂O₈存在下, LSGQD-NAs在阴极产生很强的ECL(峰值约在685 nm); 并推测了其ECL反应机理, 发现LSGQD-NAs容易通过中心未氧化的石墨烯π-π作用于GC电极表面进行组装修饰. 本研究为基于石墨烯量子点ECL传感器的研究提供了新方法.