Feasibility of using solid sampling graphite furnace atomic absorption spectrometry for speciation analysis of volatile and non-volatile compounds of nickel and vanadium in crude oil

A method for the direct determination of volatile and non-volatile nickel and vanadium compounds in crude oil without previous treatment using direct solid sampling graphite furnace atomic absorption spectrometry is proposed. The crude oil samples were weighed directly onto solid sampling platforms using a microbalance and introduced into a transversely heated solid sampling graphite tube. In previous work of our group losses of volatile nickel and vanadium compounds have been detected, whereas other nickel and vanadium compounds were thermally stable up to 1300 and 1600 °C, respectively. In order to avoid this problem different chemical modifiers (conventional and permanent) have been investigated. With 400 μg of iridium as permanent modifier, the signal started to drop already after two atomization cycles, possibly because of an interaction of nickel (which is a catalyst poison) with iridium. Twenty micrograms of palladium applied in each determination was found to be optimum for both elements. The palladium was deposited on the platform and submitted to a drying step at 150 °C for 75 s. After that the sample was added onto the platform and submitted to the furnace program. The influence of sample mass on the linearity of the response and on potential measurement errors was also investigated using four samples with different nickel content. For the sample with the lowest nickel concentration the relationship between mass and integrated absorbance was found to be non-linear when a high sample mass was introduced. It was suspected that the modifier had not covered the entire platform surface, which resulted in analyte losses. This problem could be avoided by using 40 μL of 0.5 g L⁻¹ Pd with 0.05% Triton X-100. Calibration curves were established with and without modifier, with aqueous standards, oil-in-water emulsions and the certified reference material NIST SRM 1634c (trace metals in residual fuel oil). The sensitivity for aqueous standards and emulsions was close to that for SRM 1634c, making possible the use of aqueous standards for calibration. The limits of detection and quantification obtained for nickel and vanadium under this condition were found to be 0.02 and 0.06 μg g⁻¹, respectively, for both elements, based on 10 mg of sample. Nickel and vanadium were determined in the samples with (total Ni and V) and without the use of Pd (thermally stable compounds), and the concentration of volatile compounds was calculated by difference. The results were compared with those obtained by high-resolution continuum source graphite furnace atomic absorption spectrometry by emulsion technique; no significant differences were found for total Ni and V at the 95% confidence level according to a Student's t-test.     

Molecular exclusion chromatography in studies of the vanadium- and nickel-containing species in residual oil

A residual oil sample prepared from a crude oil is chromatographed on a column having a molecular-weight exclusion limit at about 5000. Three-dimensional chromatograms (absorbance/wavelength/time) are recorded with a u.v.-visible rapid-scanning detector. The elution profiles of vanadium- or nickel-containing species are obtained by applying atomic absorption spectrophotometry to fractions of the column effluents. Both vanadium- and nickel-containing species are detected over the whole molecular-weight range available with the column. The elution profiles of vanadium and nickel differ; the major elution peak for vanadium appears at a slightly lower molecular-weight region of the chromatogram than that for nickel. By reference to the real-time recorded absorption spectra of the effluents, it is suggested that at least some of the metals are present as metalloporphyrins.     

Trace elements in Nigerian oil sands and extracted bitumens

The Nigerian oil sands are very extensive with an estimated in place reserves of bitumen/heavy oil of over 30 billion barrels. Instrumental Neutron Activation Analysis (INAA) has been used to determine the trace and minor elements in the raw oil sands and bitumens. About 43 trace elements in the raw oil sands and 30 in bitumen extracts were determined. The results are compared with values of Canadian bitumens and some Nigerian conventional light crude oils. In general, the Nigerian bitumens has higher hydrocarbon concentration than the Athabasca bitumen but slightly lower than in the Nigerian crude oils. The sulphur, vanadium and nickel contents of the Nigerian bitumens and crude oils are appreciably lower than those of Athabasca bitumen, thus indicating that the extraction and refining of Nigerian tar sand oil would pose less technological and environmental problems than the Athabasca syncrude.     

火花直读光谱法测定铝及铝合金中的钒含量

通过对测定条件的优化,采用高钒系列标准样品建立分析程序,完成类型标准化,校验后再进行测定,建立了火花直读光谱法对铝及铝合金中的钒含量进行测定的方法。选用E2235高钒标准样品进行标准化,所得测定值与标准值基本一致,相对标准偏差为2.9%(n=8)。结果表明,当测定元素含量不超过0.020%时,方法准确、可靠,适合于铝及铝合金中微量钒含量的测定。     

微波消解-ICP-MS法测定硫磺中18种微量元素

建立了用微波消解-电感耦合等离子体质谱法(ICP-MS)同时测定硫磺中18种微量元素(锂、镁、铝、钙、钒、铬、锰、铁、钴、镍、铜、锌、镉、砷、硒、钡、铅和汞)的定量分析方法。通过对消解所用试剂及条件进行研究,确定最佳的样品处理条件;为了获得最佳的信噪比并降低光谱干扰,研究采用单变量方法,对ICP-MS的射频功率和雾化气体流量等因素进行了性能优化。结果显示：该方法各元素的校准曲线线性相关系数在0.999以上,所有元素的检出限(LODs) 在0.001-0.962 mg/Kg之间,测定下限范围在0.004-3.85 mg/Kg之间,回收率在82.9 %~115 %之间,相对标准偏差均小于3 %。     

微波消解-电感耦合等离子体质谱(ICP-MS)法测定土壤七种金属元素

实验室比对盲样测定是检验实验室能力验证、实验室资质认定、机构考核的主要手段。为研究并解决测试实验室比对土壤盲样中铍、钒、镍、铜、锌、镉、铅的含量,采用微波消解电感耦合等离子体质谱(ICP-MS)法对土壤盲样进行研究,探讨了不同消解酸体系,检出限和定量限、测试模式和干扰消除、精密度和加标回收率、质控样品进行研究。结果表明：用6 mL HNO3,2 mL HCl和1 mL HF为混合酸体系,各待测元素标准曲线相关系数大于0.9995,检出限在0.001~2.985 mg.L-1^,定量限在0.003~9.94 mg.L-1^,采用氦气碰撞模式测试钒、镍、铜、锌、镉和铅,可以有效的降低多原子离子的干扰;采用no gas模式测试铍,可以有效的提高铍的测试灵敏度。方法精密度为0.2%~6.2%(n=6),加标回收率为92.3%~110.6%,采用土壤标准样品(GSS-4)进行全过程质控研究分析,各元素结果均在标准值参考范围内。用ICP-OES法测试土壤盲样中七种待测金属元素含量与用铑为内标的ICP-MS进行比对,测量分析结果基本一致。     

Graphene oxide-packed micro-column solid-phase extraction combined with flame atomic absorption spectrometry for determination of lead (II) and nickel (II) in water samples

A sensitive and simple method has been established for simultaneous preconcentration of trace amounts of Pb (II) and Ni (II) ions in water samples prior to their determination by flame atomic absorption spectrometry. This method was based on the using of a micro-column filled with graphene oxide as an adsorbent. The influences of various analytical parameters such as solution pH, adsorbent amount, eluent type and volume, flow rates of sample and eluent, and matrix ions on the recoveries of the metal ions were investigated. Using the optimum conditions, the calibration graphs were linear in the range of 7–260 and 5–85 μg L^?1 with detection limits (3S_b) of 2.1 and 1.4 μg L^?1 for lead and nickel ions, respectively. The relative standard deviation for 10 replicate determinations of 50 μg L^?1 of lead and nickel ions were 4.1% and 3.8%, respectively. The preconcentration factors were 102.5 and 95 for lead and nickel ions, respectively. The adsorption capacity of the adsorbent was also determined. The method was successfully applied to determine the trace amounts of Pb (II) and Ni (II) ions in real water samples. The validation of the method was also performed by the standard reference material.     

Simultaneous high performance liquid chromatographic determination of vanadium, nickel, iron and copper in crude petroleum oils using bis(acetylpivalylmethane)ethylenediimine as a complexing reagent

A method is described for the simultaneous high performance liquid chromatographic (HPLC) determination of copper, iron, nickel and vanadium, based on complexation of analytes by bis(acetylpivalylmethane)ethylenediimine (H(2)APM(2)en) followed by solvent extraction and HPLC separation on a reversed-phase. C-18, 5 microm column with UV detection at 260 nm. The method has been applied to the determination of metals in crude petroleum oils collected from the South Indus Basin oil fields. The results obtained are compared with those obtained by flame atomic absorption spectrometry.     

Determination of trace impurities in some nickel compounds by flame atomic absorption spectrometry after solid phase extraction using Amberlite XAD-16 resin

A simple flame atomic absorption spectrometric (FAAS) procedure for the determination of lead, bismuth, gold, palladium and cadmium as impurities in Raney nickel and nickel oxide was developed using a preconcentration step on an Amberlite XAD-16 resin packed column. Lead, bismuth, gold, palladium and cadmium were quantitatively recovered and separated from a solution containing 1 M HCl and 0.3 M NaI by the column system. Effects of the various parameters such as reagent concentrations, sample volume, matrix effects, etc. have been investigated. Under optimized conditions, the relative standard deviation of the combined method of sample treatment, preconcentration and determination with FAAS (n = 7) is generally lower than 12%. The limit of detection (3s, n = 20) was between 10–270 ng/g. The results were used for separation and preconcentration of five trace elements from nickel matrices.     

Determination of ppb concentrations of transition metals by radioisotope-excited energy-dispersive X-ray spectrometry

Using ammonium pyrrolidine dithiocarbamate as precipitant and iron as a carrier, ppb concentrations of the following elements were coprecipitated from fresh water: vanadium, chromium, manganese, nickel, copper, zinc, selenium, mercury, and lead. Precipitates were collected on membrane filters then element concentrations were determined using energy dispersive X-ray fluorescence spectrometry. Calibration curves indicate sensitivities ranging from 0.4 ppb for V, Zn, As and Hg to 1.2 ppb for Pb. It is likely that this method of preconcentration can be directly incorporated into field sampling procedures, thus eliminating the problems of sample contamination or trace element losses by absorption on container walls.     

Determination of trace impurities in cobalt by spark source mass spectrometry

An analytical method, SSMS, for the determination of trace impurities in cobalt is described. This element is used as raw material for the production of⁶⁰Co in Embalse Nuclear Power Station. Tin, aluminum, lead, silicon, molybdenum, calcium, vanadium, boron, chromium, zirconium, tungsten, nickel, magnesium, iron, zinc and copper were determined. Manganese, analyzed by AAS, was used as an internal standard. The measurements were semiquantitative. The accuracy of the results was compared with that of emission spectrography and atomic absorption spectrometry, the agreement was found to be satisfactory.     

Selective detection of volatile nickel,vanadium, and iron porphyrins in crude oils by gas chromatography-atomic emission spectroscopy

This report describes the selective detection of volatile nickel, vanadium, and iron metalloporphyrins in crude oil samples. An atomic emission detector (AED) was used for simultaneous detection of these metals using the Ni 301.2 nm, V 292.4 nm, and Fe 302.1 nm emission lines. Detection limits for these metals range from 0.05 to 5 pg/sec. The presence of volatile forms of these metals in several crude oil samples has been confirmed.     

电感耦合等离子体发射光谱法(ICP-AES)测定高铼酸钾中的19种杂质元素

建立了一种用稀盐酸溶解样品,标准工作溶液中匹配钾,ICP-AES测定高铼酸钾中19种杂质元素的方法。在选定的仪器工作条件下,样品加标回收率(%)分别为：钠94.4～101、钙98.8～102、铝98.1～102、镁95.8～99.1、钴98.4～101、钼97.3～103、钛97.6～102、钒96.6～106、锆96.2～97.7、铬97.8～101、铜98.1～108、铁92.9～104、锰95.5～98.4、镍93.6～101、钯93.3～101、铅96.5～103、锌95.2～103、铂95.9～99.9、铑94.5～96.3;方法精密度RSD%(n=7)分别为：钠2.0～5.5、镁1.1～3.5、铝0.9～2.5、钙1.5～7.3、钴1.1～3.1、钼0.9～4.5、钛1.0～2.8、钒1.6～4.0、锆1.4～3.6、铬0.77～4.6、铜0.74～1.8、铁1.3～3.8、锰1.1～2.0、镍0.99～5.0、钯1.1～2.4、铅1.3～9.1、锌0.80～6.7、铂1.2～10、铑0.78～8.6。方法简便、快速、准确, 满足生产分析要求。     

Leaching behavior of metal-containing species in residual oils with different organic solvents

The leaching behavior of two different residual oils is investigated with 24 organic solvents including alkanes, aromatics, esters, ethers ketones, alcohols and nitrogen compounds. A 2-g portion of sample oil is shaken with 20 ml of the organic solvent. The leaching of the organic matrix of the oil is determined by weighing the dissolved organic matrix after removal of solvent. The leaching of vanadium, iron and nickel was determined by flame atomic absorption spectrophotometry after ashing of the dissolved fraction. The leaching of those metals depends strongly on the solvent used; for example, vanadine is almost completely leached into toluene, but only slightly into methanol. The leaching of iron is poor compared with that of vanadium or nickel. In most solvents, leaching of those metal-containing species is poorer than that of organic material. Exceptionally, N,N-dimethylformamide is more efficient in leaching vanadium species than organic material.     

液膜预富集水相痕量镍的分析研究

研究了液膜体系对水相中痕量镍离子的富集方法,镍离子从外相水溶液被膜相载体通过液膜运进含有反萃取剂的内相,从而达到富集效果,液膜富集一次回收率达98％,二闪富集倍数250倍,试验了载体,表面活性剂,液体石蜡,膜与内相水的水／油比,乳化液与外相水的乳／水比,内相酸度,外相PH值,富集时间的破乳剂用量等因素的影响,利用正交分析试验选出了最佳试验条件,并比较在相同条件下液膜法与萃取法提取镍的效果,通过液膜富集,使原子吸收法测定痕量镍达到了10^-9级。     

Determination of vanadium by solid-phase spectrophotometry after its preconcentration as an Eriochrome Cyanine R complex on a dextran-type exchanger

A method is described for the determination by solid phase spectrophotometry (SPS) of trace amounts of vanadium in natural water and crude petroleum samples. The procedure is based on fixation on a dextran-type anion exchanger of the complex V(IV)-Eriochrome Cyanine R. The absorbance of the gel, at 563 and 750 nm, packed in a 1 mm cell, is measured directly. Vanadium can be determined in the 0.6-25.0 mug l(-1) range with a relative standard deviation of 2.2%. The comparison of the SPS method and the gallic acid persulphate method shows that the linearity, analytical sensitivity and precision were better for the SPS method, and that the latter method has lower detection and quantification limits than the gallic acid persulphate method.     

Continuous flow system for the determination of trace vanadium in natural waters utilizing in-line preconcentration/separation coupled with catalytic photometric detection

A sensitive and rapid method is presented for the determination of vanadium at ng to sub-ng ml(-1) levels in natural waters, in which in-line preconcentration/separation is directly coupled with catalytic detection of vanadium in a flow-injection system. Vanadium was adsorbed on a small column packed with Sephadex G-25 gel and desorbed with a small volume of 0.010 M HCl. The catalytic action of vanadium on the oxidation of chromotropic acid (1,8-dihydroxy-3,6-naphthalenedisulphonic acid) by bromate in pH 3.8 buffered media was used in the sensitive determination of vanadium. Effective preconcentration/separation of trace vanadium can be achieved from Fe(III), Cu(II) and a large excess of sodium chloride in seawater sample. A linear calibration using a 5 m sample loop was obtained for vanadium in the range 0-2.5 ng ml(-1). The limit of detection was 0.02 ng ml(-1) and the relative standard deviation was 1.2% for 1.0 ng ml(-1) vanadium (n=5). The present FIA system is rapid and sensitive and can be readily applied to river water and coastal seawater samples.     

纳米Ni催化剂在超稠油水热裂解降黏中的应用研究

采用甲基环己烷水正辛醇AEO9形成的微乳液体系制备纳米金属Ni催化剂，并利用该催化剂催化辽河超稠油的水热裂解反应。研究结果表明， 280℃时纳米金属Ni能够促进超稠油的水热裂解反应。与原超稠油相比，反应后样品的硫质量分数由0.45%降到0.23%，胶质、沥青质质量分数分别降低了15.83%、15.33%；GC-MS分析结果表明，甲基环己烷在改质过程中能够脱氢生成甲苯；C、H元素分析结果表明，反应后样品中胶质、沥青质的H/C原子比增加，说明从甲基环己烷上脱下的氢能够转移到超稠油中。表面活性剂AEO9、水和油，在改质结束后的降温过程中，形成了稳定的油包水型乳液，起到乳化降黏作用；而添加的甲基环己烷、正辛醇均能起到稀释降黏作用；在上述降黏作用的协同影响下，反应后样品50℃时的黏度由原来的139800mPa·s降至2400mPa·s，由此表明，纳米Ni催化剂对辽河超稠油水热裂解降黏的催化效果显著。     

Method development for the determination of nickel in petroleum using line-source and high-resolution continuum-source graphite furnace atomic absorption spectrometry

Several sample preparation methods have been investigated for the direct determination of nickel in crude oil using graphite furnace atomic absorption spectrometry (GF AAS). Xylene was found unsuitable as solvent because of the poor long-term stability of the solutions and the resulting contamination of the equipment. Isobutyl methyl ketone (IBMK) solutions exhibited better stability, but the sensitivity of the organic nickel salt used for the standard solutions showed a high day-to-day variability. An oil-in-water emulsion using Triton X-100 as surfactant gave the best results. Using high-resolution continuum-source (HR-CS) GF AAS, it could be observed that up to 50% of the nickel in crude oil, most likely low molecular weight nickel porphyrins, were lost already at pyrolysis temperatures >400 °C, whereas the rest of the nickel as well as the nickel standard were stable up to 1300 °C. The nickel absorption at a secondary line at 232.138 nm was recorded simultaneously with that at the primary line at 232.003 nm, expanding the dynamic working range by an order of magnitude. The best characteristic mass obtained was m₀=27 pg and the limit of detection was around 0.07 μg g⁻¹ Ni in oil, based on an emulsion of 2 g oil in 10 ml. The accuracy of the procedure was verified by analyzing the certified reference material (CRM) NIST SRM 1634c, Trace Metals in Residual Fuel Oil.     

The determination of uranium in alloy systems

A procedure is described for the determination of the uranium content of metallurgical alloys containing this element as a minor constituent. The uranium is first separated from the sample solution by precipitation as uranyl ammonium phosphate in the presence of ethylenediamine-totra-acetic acid. By this means the uranium is separated from many elements including iron, chromium, copper, nickel, vanadium, cerium, ncodymium and bismuth. Tho uranyl ammonium phosphate precipitate is dissolved in hydrochloric acid and the resulting solution is passed through a lead reductor. The tetravalent uranium is titrated with a standard cerie sulphate solution, using ferroin as the indicator. This procedure has proved very suitable for the analysis of bismuthuranium binary alloys containing uranium in amounts up to approximately 20%.