微晶碳电活化过程中离子尺寸效应研究

以石油焦基微晶碳作为电极材料,并由N2吸附,X射线衍射(XRD)表征其孔结构和微晶结构.研究了4种电解液Et4NBF4/PC(四乙基铵四氟硼酸盐/碳酸丙烯酯)、Et4NBF4/AN(四乙基铵四氟硼酸盐/乙腈)、Bu4NBF4/PC(四丁基铵四氟硼酸盐/碳酸丙烯酯)和Bu4NBF4/AN(四丁基铵四氟硼酸盐/乙腈)的微晶碳电容器特性.结果表明:电解质离子与溶剂AN的溶剂化半径较小,容易嵌入类石墨微晶碳层,其于AN的电活化电位比在PC中的低,致使电活化程度更深,材料的表面利用率更高,电容量较大.电解质阳离子(Et4N+,Bu4N+)大小对电活化影响不大.电活化使材料类石墨微晶层间距(d002)变大,离子尺寸越大,层间距增加越明显.     

碳纤维微晶结构的形成与生长

碳纤维的微晶结构是影响其性能的决定性因素,本论文采用广角X-射线衍射法研究了聚丙烯腈预氧纤维在碳化阶段中微晶结构的形成、生长与转变过程。研究结果表明:在1000℃以下,经预氧化反应形成的不连续多环芳香平面结构沿平行于纤维轴的方向堆积并逐渐靠近,形成类似于晶核的微晶结构生长中心,表现为类石墨片层间距的减小而晶粒增长缓慢;当温度高于1000℃时,晶粒的生长速度明显加快,形成三维有序的微晶结构;在温度高于1500℃的石墨化阶段,类石墨微晶结构进行重排,晶粒尺寸迅速增加。根据这一规律,可以通过控制晶核生成和晶粒生长速度的匹配,进行碳纤维的结构设计和调控。     

超声波活化处理对微晶纤维素结构和氧化反应性能的影响

采用无污染的超声波技术预处理微晶纤维素, 研究了微晶纤维素在活化前后的超分子结构、形态结构和可及度的变化, 超声波活化对微晶纤维素选择性氧化性能的影响.     

硫化态NiW/γ-Al2O3加氢脱硫催化剂的微观结构

采用拉曼光谱和X－射线衍射技术，对硫化态NiW/γ-Al2O3加氢脱硫催化剂进行了表征。实验结果表明，硫化态NiW/γ-Al2O3催化剂表面类WS2微晶主要以3R形式存在。对其微观结构进行分析，认为具有堆叠层数稍多且片晶较短的3R型WS2微晶与镍形成Ni-W-S活性相的催化剂，具有较高的加氢脱硫活性。     

高强高模型碳纤维与高模型碳纤维微观结构分析

利用拉曼光谱(Raman)、X射线衍射(XRD)、X射线光电子能谱(XPS)、元素分析(EA)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和小角X射线散射(SAXS)表征和分析了高强高模型碳纤维和高模型碳纤维的微观结构和化学组成.结果表明,高强高模型碳纤维的石墨微晶晶粒尺寸细小,组成微晶的石墨片层间距较大,片层间和片层边缘保留了非共轭碳构成的晶体缺陷,石墨化程度较低,微晶间缝隙较小,分布均匀,路径曲折;高模型碳纤维具有更加完善的石墨微晶结构,石墨化程度较高,微晶尺寸更大,组成微晶的石墨层堆砌整齐有序,非碳元素较少,共轭态碳明显增多,但其微晶间裂纹和孔隙结构也较大.高强高模型碳纤维因具有多层次的微观结构和缺陷,相比高模型碳纤维,有更多的应力扩散和能量存储及耗散路径,是其拉伸应变和强度保持的关键所在.     

沥青基活性炭纤维复合活化工艺的研究

以沥青基炭纤维为原料，研究了用铵盐作为化学活化剂对其进行浸渍预处理，然后采用（H2O＋CO2）活化的方法制备活性炭纤维，讨论了工艺条件对活性炭纤维性能的影响并通过光电子能谱XPS探讨了活化过程中炭纤维表面官能团的变化。结果表明：采用这种物理和化学复合活化工艺，可以在较高得率下提高活性炭纤维比表面积。同时浸渍处理、H2O流量、活化温度和活化时间等工艺参数显著影响活性炭纤维的比表面积和得率，优化的工艺为：经铵盐浸渍6h，炭纤维在水蒸气与CO2流量比3：1的混合气氛中900℃活化30min。XPS研究表明，活化后炭纤维表面的含氧官能团C－O明显减少，铵盐浸渍未能增加活性炭纤维表面的含氮基团。     

苯酚与三醋酸纤维素的超分子作用及结构研究

１引言 超分子化学的迅猛发展引起了化学界广泛的重视。本文用Ｘ射线粉末衍射仪以苯酚与三醋酸纤维素为例研究了他们之间的超分子作用及它们间的作用机理和结构。苯酚的羟基与三醋酸纤维素酯羰基之间通过氢键以及二醋酸纤维素的特有空隙系统,形成一种包合络合物。２实验部分２．１仪器及试剂Ｒｉｇａｋｕ Ｄ／ｍａｘ－３ｃ Ｘ射线粉末衍射仪（理学公司）;苯酚（Ａ．Ｒ．）;微晶纤维素（层析用）;羧甲基纤维素（ＣＭＣ）（山东鱼台助剂厂）;三醋酸纤维索（合成）。２．２实验方法取固定量的苯酚分别加入一定量的二醋酸纤维素、微晶纤维…     

柠檬酸浸渍改性H-β沸石对2-(4′-乙基苯甲酰基)苯甲酸脱水合成 2-乙基蒽醌反应的催化性能

采用浸渍法制备了柠檬酸改性的H-β沸石催化剂,采用X射线衍射、X射线荧光、红外光谱、核磁共振和程序升温脱附方法对催化剂进行了表征,并考察了催化剂对2-(4′-乙基苯甲酰基)苯甲酸(EBA)脱水合成 2-乙基蒽醌(EAQ)反应的催化性能. 结果表明,经柠檬酸改性没有破坏H-β沸石的骨架结构,但其酸量明显减少. 柠檬酸浸渍改性后未经水洗的催化剂上有较多的非骨架铝及柠檬酸残留;水洗至中性的催化剂在EBA脱水合成EAQ反应中有较好的催化性能, EBA转化率可高达96.5%, EAQ选择性可高达96.0%.     

用氨气爆破法使纤维素活化的研究

本文用扫描电子显徽镜、X—射线衍射、碘吸收值以及碱溶解度来研究精制棉绒经氨气爆破法处理后的形态及结构的变化,实验证明,处理后的棉绒纤维其外表发生破裂,X—射线衍射图显示其结晶结构出现纤维素Ⅰ和纤维素Ⅲ的混晶,碘吸收值增大,碱溶解度也增大,随着爆破压力的增加这种效果更为显著,最后用乙酰化速度证实经处理后的棉绒其反应性能有较大的提高。     

不同方法制备的Cu-Cr/γ-Al2O3的结构及其对糠醛加氢制2-甲基呋喃反应的催化性能

 利用普通浸渍法、共沉淀法和溶剂化金属原子浸渍法制备了一系列Cu－Cr／γ－Al2O3催化剂，并用X射线衍射、扫描电镜、透射电镜和X射线光电子能谱等技术对这些催化剂进行了表征．结果表明，不同方法制备的催化剂的金属粒度的顺序为溶剂化金属原子浸渍法＜共沉淀法＜普通浸渍法；金属还原程度的顺序为溶剂化金属原子浸渍法＞普通浸渍法≈共沉淀法．糠醛加氢反应实验结果表明，催化活性顺序为溶剂化金属原子浸渍法＞普通浸渍法＞共沉淀法；生成2－甲基呋喃选择性顺序为共沉淀法＞普通浸渍法＞溶剂化金属原子浸渍法．     

空心活性碳纤维SNACF的织构和表面化学结构的研究

本工作借助透射电子显微镜(TEM)、扫描电子显微镜(SEM)、X-射线衍射、X-射线光电子能谱(XPS)、红外光谱和化学滴定等技术,研究了空心活性碳纤维SNAGF的织构和表面化学结构特征。实验结果表明,SNAGF具有多孔性微晶碳结构,其表面存在着碱性官能团和羧基、酚基等酸性官能团及高氧态硫(如磺酸及砜基类等)官能团。     

Phosphonated fully aromatic polyethers for PEMFCs applications

New homopolymers and copolymers based on aromatic polyethers bearing side diphosphonate and diphosphonic groups have been synthesized. These synthetic efforts resulted in homo and copolymers of high thermal stability but moderate molecular weights. To evaluate the influence of the immobilized phosphonate ester and phosphonic acid moieties on polymer electrolyte membranes for fuel cells applications, blends of the newly synthesized homo and copolymers with a pyridine‐based aromatic polyether were prepared. These blends were miscible with high glass transition temperatures and high thermal stabilities. Furthermore, the introduction of these groups to a polymeric backbone significantly increases the doping ability in phosphoric acid compared to the net matrix as well as the ionic conductivity for high doping levels. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2817–2827, 2010     

载银磷酸活化剑麻基活性炭纤维的抗菌性能研究

本文利用磷酸化方法，制备各种剑麻基活性炭纤维，并利用活性炭纤维的氧化还原特性及吸附性能，在其上负载金属银，研究并比较了这些载银活性炭纤维对大肠杆菌和金黄色葡萄球菌的杀灭作用，结果表明，磷酸浓度，活化方法，活化时间，纤维的比表面积等因素的均对材料的抗菌性能有一定的影响，磷酸活化的活性炭纤维表现出强的抗菌杀菌能力，高浓度磷酸活化后的纤维抗菌能力有所提高，并且抗菌能力随活化时间的延长而增加，抗菌前后纤维上负载的银未曾大量脱落，经5次抗菌试验后材料仍显示出很强的抗菌能力。     

活性碳纤维对银离子还原吸附能力的改进

活性碳纤维不仅对有机物有高的吸附容量,对贵金属离子也具有强的还原吸附能力,可将Pd(Ⅱ）,Ag（Ⅰ）,Au（Ⅲ）等离子还原为金属单质。因而可用于提取矿液或加收废液中的贵金属。由此,提高或改善贵金属在活性碳纤维上的还原吸附容量或分布形成,显得非常重要。本文研究了活性碳纤维制备条件、表面氧化改性、以有负载有机物等对活性碳纤维还原能力的影响。结果表明,（1）制备条件对剑麻基活性碳纤维的还原能力有很大的影响。用H3PO4或ZnCl2活化的活性碳纤维对银离子具有更高的还原吸附容量,分别可达250和700mg/g,约为水蒸汽活化剑麻基活性碳纤维对银离子还原吸附容量的2倍和5倍。（2）过氧化氢、高锰酸钾、或硝酸等无机氧化剂对活性碳纤维进行表面改性,也能提高活性碳纤维的还原能力。结果表明,虽然改性活性碳纤维的比表面积和孔体积下降10-20%左右,但基表面含氧量及含氧基团的种类发生了改变。这些改性活性碳纤维对Ag(NH3)2^ 的还原吸附量大幅度提高,可达550mg/g以上。推断表面改性在活性碳纤维表面创造了更多有利于碱性条件下发生氧化还原的活性点。（3）在活性碳纤维表面负载适当的有机物如亚甲基蓝、苯胺或对硝基苯酚,也能显著提高活性碳纤维对Ag(NH3)2^ 的还原吸附能力。     

Pd‐initiated polymerization of diazo compounds bearing dialkoxyphosphinyl group and hydrolysis of the resulting polymers and oligomers to afford phosphonic acid‐containing products

Pd‐initiated polymerization and oligomerization of diazo compounds containing a dialkoxyphosphinyl group are described. Polymerization of 2‐dialkoxyphosphinylethyl diazoacetates with π‐allylPdCl‐based initiating systems afforded C? C main chain polymers bearing phosphonate on each main chain carbon atom. The quantitative transformation of the side chain phosphonate to phosphonic acid resulted in the formation of water soluble polymers having the acid groups accumulated around their main chains, although the carbonyl ester linkage in the side chain was cleaved via intramolecular acid‐assisted hydrolysis in water at 80 °C. Pd‐initiated oligomerization of diethyl diazomethylphosphonate yielded an oligomeric product bearing diethoxyphosphiny groups directly attached to its main chain carbons, with unexpected incorporation of azo group in the main chain framework. Hydrolysis of the phosphonate of the oligomer afforded a water‐soluble product, which was revealed to show higher proton conductivity than poly(vinylphosphonic acid) under certain conditions. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1742–1751     

Properties of polyethylene modified with phosphonate side groups. I. Thermal and mechanical properties

Low-density polyethylene was modified by the inclusion of phosphonate ester pendent groups by using an oxidative chlorophosphonylation reaction followed by esterification of the polyethylene poly(phosphonyl chloride) with an alcohol. Two different types of phosphonate esters were prepared: dimethyl phosphonate from the reaction with methanol and a phosphonate graft copolymer from the reaction with hydroxy-terminated poly(ethylene oxide) (PEO). For the latter, oligomers with molecular weights of 350 and 750 were used. For each type of phosphonate, a series of polymers were prepared with pendent group concentrations ranging from 0 to 9.1 substituents per 100 carbon atoms. The modified polymers were characterized by infrared spectroscopy, differential scanning calorimetry, and by measurement of the tensile modulus. Infrared spectroscopy proved to be useful for determining if the polymer modification reaction resulted in entirely phosphonate ester pendent group substitutions or if unesterified phosphonic acid groups were also present. The polymers prepared in this investigation exhibited no infrared absorbances arising from phosphonic acid groups. The presence of phosphonate ester groups resulted in a decrease of crystallinity with increasing phosphonate concentration and with the exception of the polymers containing 9.1 PEO–phosphonate grafts per 100 carbon atoms, the effect of phosphonylation on the melting temperature of the polymers was consistent with Flory's theory for the melting point depression of random copolymers. The tensile modulus measured from a constant uniaxial elongation experiment decreased with increasing phosphonylation. The behavior of all three phosphonate series was identical and could be attributed to the effect of decreasing polymer crystallinity.     

Surface-esterified cellulose fiber in a polypropylene matrix: impact of esterification on crystallization kinetics and dispersion

Cellulose powders hydrophobized by surface esterification with carboxylic acids with different chain lengths (3, 10 and 18 carbons) were dispersed in a polypropylene matrix. Quality of the dispersion and nucleation activity of the filler were investigated by means of differential scanning calorimetry and optical microscopy. The results showed that the esterification decreases the crystallization rate in case of cellulose esterified with propionic or decanoic acid. On the other hand, the oleic acid ester demonstrated slightly higher crystallization rates than the unmodified cellulose, which was ascribed primarily to the newly arisen non-esterified surface after disintegration of the filler. Optical microscopy with hot stage showed the high nucleation ability of the natural cellulose fiber and its suppression in case of esterified surfaces. A complete inability to nucleate polypropylene crystallization was observed in case of decanoyl ester, while the other two retained some activity, but lower than that of the natural fiber. Finally, analysis of the filler dispersion and distribution revealed that the decanoyl and octadecanoyl esters disintegrate during melt mixing, while both dispersion and distribution of the fibers modified with propionic acid are poor.     

Continuous cellulose fiber-reinforced cellulose ester composites III. Commercial matrix and fiber options

Thermoplastic composites were prepared using two continuous regenerated cellulose fiber types, rayon and lyocell, and with several different commercially-available thermoplastic cellulose esters as matrix. Matrix options included cellulose acetate propionate (CAP), and several cellulose acetate butyrates (CAB) with different butyryl content, having different molecular weights and different methods of plasticization (adipates and very low molecular weight cellulose ester fractions). Choice of cellulose ester type was generally found to have little or no effect on mechanical properties. A significant effect, however, was revealed for fiber type. The lyocell-based composites thereby were reflective of the greater stiffness of a fiber produced from anisotropic solution state. Their modulus consistently exceeded 20GPa whereas the rayon fiber-based composites had moduli between 6 and 8GPa. The latter, however, possessed failure strains that were 3 to 4 times greater than their stiffer counterparts.     

芳纶纤维/SMPU-SiO2复合材料的界面性能研究

选用形状记忆聚氨酯(SMPU)和正硅酸乙酯(TEOS)为前驱体,固体酸对甲基苯磺酸(PTSA)为催化剂,利用空气中的水分为水解水源,通过溶胶-凝胶法原位制备了形状记忆聚氨酯与二氧化硅( SMPU-SiO2)杂化材料,并将杂化材料应用于芳纶纤维增强的柔性复合材料中,以期改善芳纶纤维与基体的界面性能.同时,针对芳纶纤维表面...     

煤焦油沥青基纤维状活性炭的吸附性能

煤焦油沥青基炭纤维（ＣＰＣＦ）价格低廉含炭量高、易于活化,是制备纤维状活性炭（ＣＰＡＣＦ）的优良原料。本文讨论了ＣＰＣＦ的抗拉强度和活化条件对ＣＰＡＣＦ比表面积的影响。并同石油系沥青基炭纤维（ＰＰＣＦ）进行了比较。考察了不同比表面积的ＣＰＡＣＦ、ＰＰＡＣＦ和商品用颗粒活性炭（ＡＣ）对０．１ｍｏｌ／Ｌ碘溶液、０．００５ｍｏｌ／Ｌ亚早兰溶液和２９３Ｋ下三氯甲烷饱和蒸汽的吸附性能,及以上三样品在２９３Ｋ