等色吸收荧光猝灭法快速测定食品中苏丹红Ⅰ

在乙醇介质中, 强荧光染料吖啶的荧光波长478 nm与苏丹红Ⅰ的吸收光波长480 nm十分接近, 由于等色性苏丹红Ⅰ能够有效吸收吖啶发出的荧光, 使吖啶在激发波长λex=410 nm、荧光波长λem=478 nm处荧光猝灭, 依此建立了荧光猝灭测定苏丹红Ⅰ的新方法. 该方法快速、简便, 其线性范围为3.72～37.2 mg/L, 方法检出限为1.1 mg/L. 用于辣椒、辣椒酱食品中痕量苏丹红Ⅰ的测定. 6次平行测定, 相对标准偏差为0.8%～2.7%, 加标回收率为89.5%～104.0%.     

近红外光谱法测定成品汽油中的芳烃和烯烃含量

介绍了近红外光谱测定90#汽油及93#汽油中芳烃和烯烃含量。选择1100～1300nm的近红外光谱域,在荧光指示剂吸附法的基础上,采用偏最小二乘法建立了适合测定90#汽油及93#汽油中芳烃和烯烃含量的分析模型,通过大量试验对所建分析模型的可靠性进行了验证。近红外光谱法的测定结果与荧光指示剂吸附法的测定结果具有很好的一致性。与荧光指示剂吸附法相比,近红外光谱法可以提高分析效率,降低分析成本,具有较高的分析精密度。     

微波消解-荧光猝灭法测定痕量铜的研究

利用微波消解前处理样品,在(CH2)6N4(六亚甲基四胺)-HCl介质中,溶液中的铜能与甲磺酸加替沙星形成稳定的络合物,使甲磺酸加替沙星的内源性荧光显著猝灭,据此建立了铜-甲磺酸加替沙星的荧光分析新方法.该体系的最大激发波长λex=365 nm,最大发射波长λem=500 nm,铜浓度在4.0×10-8 ～1.2×10-5 mol/L范围内,与荧光猝灭程度成正比.检出限为1.2×10-8 mol/L,回收率为97% ～104%.该法可直接用于测定铜含量,结果令人满意.     

同步扫描-双波长荧光分光光度法同时测定三种儿茶酚胺类神经递质

提出了用同步扫描-双波长荧光分光光度法同时测定肾上腺素(EP)、去甲肾上腺素素(NEP)和多巴胺(DA)3种儿茶酚胺类神经递质.试验表明:荧光检测宜选定发射波长(λen)与激发波长(λex)的波长差为70 nm(△λ=λem-λex)的条件下进行同步扫描.在λem为385.0 nm时DA的荧光信号不受EP和NEP的干扰,而EP和NEP相互的干扰,采用双波长荧光检测模式可消除.选择测定NEP的波长对为470.0 nm(λem,1)和531.8 nm(λem,2),测定EP的波长对为500.0 nm(λ'em,1)和445.6 nm(λ'em,2).测得荧光强度与3种儿茶酚胺浓度在320 μg·L-1(EP),640 μg·L-1(NEP)及160μg·L-1(DA)内呈线性关系,检出限(3σ/k)依次为0.20,0.97,0.73 μg·L-1.     

液膜分离富集二甲氧基羟基苯基荧光酮荧光猝灭法测定微量钼的研究

研究了在pH5．0～6．4的HAC-NaAC缓冲介质中和CTMAB存在下,Mo(Ⅳ)对二甲氧基羟基苯基荧光酮(DMH-PF)的荧光猝灭效应,建立了荧光猝灭法测定微量Mo(Ⅳ)的新体系,DMH-PF最大激发波长为λex=514nm、最大发射波长为λem=547nm,DMH-PF与Mo(Ⅵ）形成1：2配合物使荧光猝灭,荧光猝灭量与Mo(Ⅵ)在0～0．072mg／L范围内呈线性关系,方法的检出限为0．0022mg／L,体系稳定,灵敏度高,采用液膜分离富集钼,可应用于合金钢和石墨中微量钼的测定。     

色氨酸-亚硝酸体系荧光性质的研究及应用

本文首次提出了利用亚硝酸氧化色氨酸的荧光反应测定色氨酸的方法。亚硝酸氧化色氨酸,继而在氢氧化钠介质中生成荧光物质,其激发波长和发射波长分别是:λ~e~x=320nm,λ~e~m=392nm。当色氨酸浓度为0.2～1.6μg/mL时,工作曲线呈良好的线性。本方法用于测定蛋白质样品中的色氨酸,结果令人满意。本文还对反应产物的特性进行了研究。     

氧氟沙星在胶束体系中的荧光特性及应用

研究发现十二烷基硫酸钠胶束对氧氟沙星荧光有明显的增敏作用，据此建立了直接测定人体尿液中氧氟沙星的等波长差同步荧光光谱法（△λ=90nm）。经样品测定，其线性范围为0．12－3．6mg/L，检出限为0．12mg/L，回收率为92．2％－97．8％，相对标准偏差为1．2％－2．7％。     

茶多酚的三维荧光光谱特征

应用三维荧光光谱技术,研究了茶多酚溶液的三维荧光光谱特征,以及不同浓度、pH值、缓冲液、有机溶剂等因素对可见光区荧光的影响。研究表明:茶多酚溶液的三维光谱可分为三区(以激发波长/发射波长λex/λem表示):Ⅰ区:210 nm/315 nm、270 nm/315 nm;Ⅱ区:335 nm/395 nm;Ⅲ区:490 nm/515 nm。随浓度增大,茶多酚荧光的激发、发射波长逐渐红移。茶多酚浓度3 mg/mL,溶液pH 7.55条件下可灵敏检测Ⅲ区可见光区荧光;常用缓冲溶液对Ⅲ区荧光均有不同程度的增敏效果;质子化溶剂有利于Ⅲ区的荧光发射。据此可为茶多酚的快速、无损分析检测及应用开发提供新的思路。     

同步荧光光谱法测定蜂蜜中游离氨基酸

在乙酸盐缓冲介质中,氨基酸与乙酰丙酮及甲醛反应生成发出黄绿色荧光的化合物N-取代-2,6-二甲基-3,5-二乙酰基-1,4-二氢吡啶,基于此反应提出了测定蜂蜜中游离氨基酸的方法.在氨基酸的最大激发波长μex并在选定的最佳波长差△λ的条件下测定相应氨基酸的同步荧光信号.试验发现:对不同的氨基酸,其λex,△λ和所生成的荧光化合物的相对荧光强度以及线性范围均稍有差异.以丙氨酸为例,在λex为387 nm,△λ为85 nm及扫描速率为1 000 nm·min-1的条件下进行测定,所得线性回归方程为y=49.03 x 148.11(r=0.999 2),线性范围为1.0～10.0 mg·L-1.应用此方法测定了蜂蜜样品中游离氨基酸的总量,在此基础上进行回收试验,测得回收率的平均值为99.3%.     

牛蒡苷与牛蒡苷元的荧光性质及中药牛蒡子中牛蒡苷的荧光法测定

牛蒡苷和牛蒡苷元的三维荧光图谱中均呈现2个荧光峰,激发波长λex分别为230 nm和280 nm,发射波长(λem)均为310 nm。牛蒡苷的荧光远强于牛蒡苷元的荧光。溶液酸度对牛蒡苷和牛蒡苷元的荧光强度有明显影响。在pH13.0时,牛蒡苷的荧光增强,而牛蒡苷元的荧光猝灭。牛蒡子药材的三维荧光图谱和薄层荧光色谱表明,牛蒡子的荧光成分主要为牛蒡苷,而牛蒡苷元及其他共存组分在强碱性条件下对牛蒡苷的荧光无影响。据此,以甲醇为溶剂制备牛蒡子样品提取液,用水适当稀释并调节至pH 13.0,在λex/λem=280 nm/310 nm波长下测定牛蒡苷的含量。在0.014 5~2.03 mg·L-1范围内,荧光强度与牛蒡苷浓度间呈良好线性,其线性方程为IF=2.7+148.7ρ(mg·L-1),相关系数(r)为0.999。用本法测得牛蒡子对照药材中牛蒡苷的含量为6.01%,平均加标回收率为98.1%。用薄层荧光扫描法对本方法进行验证,结果表明,本法结果可靠,可用于牛蒡子药材的质量检验。     

Development and validation of a pre-column reversed phase liquid chromatographic method with fluorescence detection for the determination of primary phenethylamines in dietary supplements and phytoextracts

A sensitive and selective reversed-phase liquid chromatographic (RP-LC) method was developed and validated to determine octopamine, tyramine and Tyrosine (Tyr) in complex matrices as formulations and phytoextracts (Citrus aurantium), after pre-column derivatization with o-phthaldialdehyde (OPA) reagent. The chromatographic separations were performed at room temperature on a Phenomenex Luna C18 column using methanol and sodium acetate buffer (pH 5.5) by varying composition gradient elution as mobile phase and detected flurometrically at λ(em)=455 nm with λ(ex)=340 nm. The results obtained by the proposed method were compared with those achieved by a validated direct RP-LC method with fluorescence detection at λ(em)=310 nm with λ(ex)=275 nm, as reference method, using a Phenomenex Gemini C18 column under isocratic elution conditions with acetonitrile and sodium 1-heptanesulphonate (pH 3), as mobile phase. The higher sensitivity of the derivatization method (detection limit about 0.06 pmol) allowed the sure determination of octopamine present in traces in the examined samples. The repeatability of method (RSD) was ≤1.90% and there was no significant difference between repeatability and intermediate precision data. Recovery studies showed good results 99.5-101.3% with RSD ranging from 0.8 to 1.2%. All analyses were performed by mild conditions in absence of preliminary difficult extraction methodologies or laborious step of sample pre-treatment.     

Characterization of Gasoline by 1H Nuclear Magnetic Resonance and Chemometrics

Automotive fuel adulteration is an old and significant problem. One common type of fuel adulteration is the addition of diesel to gasoline. Unsupervised models were developed through hierarchical cluster and principal component analysis models. Supervised models through partial least square discriminant analysis using ¹H nuclear magnetic resonance spectra as the input were used to classify samples as adulterated or unadulterated. Quantitative models were developed using partial least squares to determine the gasoline and diesel concentrations in the samples. This set contained samples composed of pure gasoline and anhydrous ethanol reproducing commercial gasoline and other samples treated with diesel. Hierarchical cluster and principal component analysis did not distinguish between adulterated and unadulterated samples except for the most adulterated materials. However, partial least square discriminant analysis classified 100% of the samples correctly. The partial least square algorithm provided excellent regression models for the gasoline and diesel content. The determination coefficient was 0.9920 for both models, whereas the root mean square error of cross-validation and root mean square error of prediction for the diesel model were 2.32 and 1.42%, respectively, and 2.40 and 1.38% for the gasoline model.     

含有双发色团的化合物分子内能量传递的研究

合成了一系列含有萘环和蒽环的不同链长的二元化合物, 简写为N-Mn-A(n=2,4,6,8,10)。在有机溶剂中做了上述系列化合物的荧光光谱。激发波长为λex=280nm时, 发现荧光光谱中有两个发射峰, λem1=370nm, λem2=450nm。前者为萘的荧光峰, 后者为蒽的荧光峰。实验证明, 只有萘吸收280nm的光, 而蒽无吸收。所以在激发萘的条件下, 能量由处于激发态的萘环传向了外于基态的蒽环。在不同的有机溶剂中, 分别做了该系列化合物的荧光光谱随浓度的变化。实验结果指出, 两个荧光峰强度的比值不随浓度的变化而变化, 表明其能量传递为分子内的能量传递。另外在1%的糖淀粉水溶液中, N-Mn-A的浓度为1.0×10^-^5mol.dm^-^3,通过荧光光谱发现没有发生能量传递。表明处于伸展状态的N-Mn-A化合物分子不能发生能量传递。     

Determination of Toosendanin Extracted from Traditional Chinese Medicine: the Fruit of Melia azedarach LC–FD Detection

A rapid and selective reversed-phase liquid chromatography with fluorescence detection was developed and validated for the determination of toosendanin in the fruit of Melia azedarach. After extraction, the extracts were analysed at 25 °C using Eclipse XDB-C18 column (4.6 mm × 150 mm; 5 μm) and a mobile phase consisting of methanol–water at a flow rate of 1.0 mL min^?1. Detection wavelength was set at λ_Ex = 230 nm, λ_Em = 320 nm. The linearity, accuracy, and precision of the method were good, and the method can be successfully used to investigate the level of toosendanin component in herb samples with satisfactory results.     

疏水作用对光化学和光物理过程的影响 ⅩⅢ.△5雄甾-3β-(1-萘乙酰)-17-丹酰酯在不良溶剂中的簇集和分子间能量传递

在二甲基亚砜-水(DMSO-H₂O)混合溶剂中,随着水的体积分数(Φ)增大,△⁵雄甾-3β-(1-萘乙酰)-17-丹酰酯(1)分子中丹酰基荧光峰逐渐红移,但当Φ>0.4时,丹酰基荧光峰突然由550 nm移至500 nm。表明1发生了簇集。用280 nm光激发时,伴随丹酰基荧光的蓝移,萘基的荧光明显降低,丹酰基的荧光增强,表明簇集体内1的分子相互靠近,有利于萘基向丹酰基进行分子间的能量传递。萘基向丹酰基进行能量传递的效率在簇集体外和簇集体内分别为18%和90%。荧光寿命的测定和使用不同激发波长的实验表明簇集发生后,仍有部分分子未发生簇集。     

汽油样品类型的模式识别研究与应用

研究了应用化学计量学方法解决汽油单体烃的气相色谱分析中单体烃定性库的自动选择问题。通过提取汽油单体烃谱图中的29个组分及其含量信息作为特征值,利用主成分分析法对不同工艺得到的催化裂化汽油、焦化汽油、直馏汽油、重整汽油和烷基化汽油进行分类,结合相似分析方法(即SIMCA方法)建立了各类汽油样本的类模型,借助这些类模型可以实现对未知样本的类型判别。所提出的识别方法可方便快速地判别待分析样品所属的汽油类别,并据此推荐适合该样品的定性模型库,从而实现汽油单体烃的快速、自动分析。     

Effect of the solvent composition in methanol-pentane and methanol-acetonitrile mixtures on the spectral and luminescent properties of 1,2-dihydroquinolines

The dependence of absorption and fluorescence spectra, quantum yields, and lifetimes of fluorescence on the solvent composition in the MeOH-C₅H₁₂ and MeOH-MeCN mixtures was studied for 2,2,4,6-tetramethyl-1,2-dihydroquinoline (TMDHQ). The variations in the parameters of deconvolution of the absorption and fluorescence spectra by the Gaussian functions in the MeOH-C₅H₁₂ mixtures of various compositions indicate the specificity of methanol clustering in saturated hydrocarbons and hydrogen bonding between TMDHQ and the methanol clusters of different compositions. At low MeOH concentrations (∼0.2 vol %), TMDHQ molecules are practically completely bound with the MeOH molecules by hydrogen bonds. In the MeOH-MeCN mixtures, the changes in the absorption and fluorescence spectra are observed at a substantially higher MeOH concentration (≥10 vol %) and monotonically change at the further increase in the MeOH concentration that is caused by the peculiarities of MeOH clustering in acetonitrile and the distribution of the TMDHQ molecules between the solvent components. At 50–95 vol % of MeOH in the mixture with MeCN, the fluorescence decay kinetics is described by the biexponential curve with the lifetime of the major component (τ₁) decreasing from 7.5 to 1.1 ns in pure MeCN and MeOH, respectively, and the lifetime of the minor component τ₂ ≈ 4 ns corresponding to the fluorescence lifetime in the solution containing 50 vol % MeOH. This indicates the existence of the free TMDHQ molecules, which are not bound with MeOH molecules or their clusters.     

Application of a fluorescent derivatization reagent 9-chloromethyl anthracene on determination of carboxylic acids by HPLC

A simple and sensitive high-performance liquid chromatography (HPLC) method is proposed for the analysis of some carboxylic acids in food samples and the environment. The use of 9-chloromethyl anthracene as a fluorescence-labeling reagent has been investigated. The derivatization reagent reacts with unitary carboxylic acids and tetrabutylammonium bromide as a catalyst within 50 min in acetonitrile to give esters, which can be separated by HPLC employing fluorescence detection at λ(ex) = 365 and λ(em) = 410 nm. The optimum conditions for derivatization, fluorescence detection and chromatographic separation are established. The method shows good sensitivity, with a detection limit from 0.18 to 2.53 pmol, and good linearity between 1-250 nmol/mL of each analyte. The practical applicability of the method was demonstrated by analyzing samples that were spiked with the acid standards, environment and food samples.     

FT-IR spectroscopy and chemometrics as a useful approach for determining chemical-physical properties of gasoline, by minimizing analytical times and sample handling

Since recently Mid-Infrared Spectroscopy is being used in the petrol industry for determining important chemical-physical properties of gasoline. This technique enables to achieve results similar to those obtainable with standard methods at shorter times, lower costs and safer sample handling. This can be obtained by employing multivariate regression models in the framework of a chemometric analytical approach. In the present work some gasoline properties including density, Reid vapor pressure, Research Octane Number, aromatic hydrocarbons content and fraction recovered at 70 degrees C were determined with standard methods (ISO, CEN, ASTM) on 93 samples of unleaded gasoline produced in an oil refinery. The same samples were also analyzed by FT-IR spectrophotometry, recording absorptions of seven characteristic bands. The obtained values of chemical-physical and spectroscopic properties were used to develop and validate a multivariate regression model. This established an experimental correlation between these two sets of variables derived from the same gasoline samples. The model was able to correctly predict the chemical physical properties of a set of unknown gasoline samples produced in the same refinery starting from the spectroscopic ones.     

Elemental analysis of airborne dust samples with TXRF: Comparison of oxygen-plasma ashing on sapphire carriers and acid digestion for sample preparation

The concentrations of 13 elements (As, Ca, Co, Cd, Cr, Fe, Ga, Ni, Pb, Pt, Ti, V and Zn) were determined in air particulate matter using total reflection X-ray fluorescence spectrometry (TXRF). For silicon analysis synthetic sapphire was chosen as a new sample carrier material – it is silicon-free, resistant to oxygen-plasma, microwaves and concentrated acids. The dust samples were collected on cellulose acetate filters. The decomposition of the filters was carried out by oxidation in a microwave-generated low-pressure oxygen-plasma directly on the TXRF sample carriers. The recovery of the investigated elements was verified with the standard reference material SRM 1648 (urban particulate matter) and ranged from 90 to 97%. The oxygen-plasma method was compared with conventional sample preparation by acid digestion. Received: 9 April 1999 / Revised: 18 May 1999 / Accepted: 3 June 1999