ZnM-CO3(M＝Al、Fe)、ZPM-CO3(Z＝Zn、Cu,P＝Co、Ni)水滑石的合成及表征

水滑石是一种具有层状结构的阴离子粘土,其结构类似于水镁石,化学通式为[M2+1-xM3+x(OH)2][An-]x/n·mH2O,其中M2+和M3+分别代表层板上占据八面体氢氧化物中心位置的二价和三价金属离子,An-为层间阴离子.     

ZnM—CO3（M=Al,Fe）,ZPM—CO3（Z=Zn,Cu,P=Co,Ni）水滑石的合成与表征

水滑石是一种具有层状结构的阴离子粘土,其结构类似于水镁石,化学通式为[M2+1-xM3+x(OH)2][An-]x/n·mH2O,其中M2+和M3+分别代表层板上占据八面体氢氧化物中心位置的二价和三价金属离子,An-为层间阴离子.     

Mg-Al-CO_3与Zn-Al-CO_3水滑石热稳定性差异的研究

层状双金属氢氧化物（ Layered double hydroxides,简称 LDHs）是一类近年来发展迅速的阴离子型粘土,又称水滑石,其组成通式为： [M? 1-xM? x(OH)2]x＋ Ax/nn-mH2O,其中 M?是二价金属离子, M?是三价金属离子, An－是阴离子。这种材料是由相互平行的层板组成,层板带有永久正电荷;层间具有可交换的阴离子以维持电荷平衡。通过离子交换可在层间嵌入不同的基团,制备许多功能材料,被广泛用作催化剂、吸附剂及油田化学品等,已引起人们的关 注 [1～ 4]。有关 Mg-Al-CO3与 Zn-Al-CO3水滑石的合成及性能研究国内外已有大量报道 [1…     

Cu-Ni-Mg-Al-CO_3四元水滑石的合成及结构分析

以Cu(NO3)2 ·3H2 O,Ni(NO3)2 ·6H2 O,Mg(NO3)2 ·6H2 O和Al(NO3)3·9H2 O为原料,以NaOH和Na2 CO3为沉淀剂,采用成核/晶化隔离法合成了Cu Ni Mg Al CO3四元水滑石,通过XRD,FT IR,TG DTA,ICP等手段对样品进行测试和表征,并且对水滑石结构的层板和层间阴离子相互作用进行分析和讨论.结果表明,控制Cu2 +离子与其它二价金属离子的配比,可制备晶体结构规整的M(II)4 M(III)2 (OH)12 CO3·4H2 O型水滑石;Cu2 +离子的引入导致了明显的Jahn Teller效应;且随Mg2 +量的增加,使得这种效应更加显著,另一方面Mg2 +量的增加有利于Cu Ni Mg Al CO3四元水滑石晶体在a方向上生长,增强其热稳定性     

乙二胺四乙酸柱撑镁锌铝三元水滑石的制备与表征

采用共沉淀法合成了Mg2ZnAl-CO3水滑石;以其为前驱体,利用离子交换法进行插层组装得到Mg2ZnAl-EDTA三元柱撑水滑石;采用X射线衍射仪和傅立叶变换红外光谱仪对产物进行了表征.结果表明,合成的Mg2ZnAl-CO3水滑石纯度高、晶型良好,其层间CO32-可被乙二胺四乙酸(EDTA)阴离子取代形成Mg2ZnAl-EDTA三元柱撑水滑石;柱撑水滑石的层间距离明显增加,EDTA阴离子在层间倾斜排列.     

Cu-Ni-Mg-Al-CO3四元水滑石的合成及结构分析

以Cu(NO3)2·2H2O,Ni(NO3)2·6H2O,Mg(NO3)2·6H2O和Al(NO3)3·9H2O为原料 ，以NaOH和Na2CO3为沉淀剂，采用成核／晶化隔离法合成了Cu-Ni-Mg-Al-CO3四元 水滑石，通过XRD，FT－IR，TG－DTA，ICP等手段对样品进行测试和表征，并且对 水滑石结构的层板和层间阴离子相互作用进行分析和讨论。结果表明，控制Cu^2+ 离子与其它二价金属离子的配比，可制备晶体结构规整的M(Ⅱ）4M(Ⅲ)2(OH) 12CO3·4H2O型水滑石；Cu^2+离子的引入导致了明显的Jahn-Teller效应；且随 Mg^2+量的增加，使得这种效应更加显著，另一方面Mg^2+量的增加有利于Cu-Ni- Mg-Al-CO3四元水滑石晶体在a方向上生长，增强其热稳定性。     

Mg-Al-CO3与Zn-Al-CO3水滑石热稳定性差异的研究

层状双金属氢氧化物（Ｌayered double hydroxides,简称ＬＤＨs）是一种类近年来发展迅速的阴离了型粘土,又称水滑石,其组成通式为[M（II）1－xM(III)x(OH)2]x(OH)2]^x＋Ax/n^n-mH2O,其中M（II）是二介金属离子,M（III）是三价金属离子,A^n-是阴离子,这种材料是由相互平行的层板组成,层板带有永在电荷,层间具有可交换的阴离子以维持电荷平衡,通过离子交换可在层间嵌入不同的基团,制备许多功能材料,被广泛作催化剂、吸附剂及油田化学品等,已引起人们的关注^[1-4]。有关Mg-Al-CO3与Zn-Al-CO3水滑石的合成及性能研究国内外已有大量报道^[1,2],本文对两者热稳定性存在的差异进行了研究,这对深化此类材料的认识具有参考作用。     

原位聚合法制备聚丙烯酸甲酯/ZnAl层状双氢氧化物插层纳米复合材料及其形貌特征

近 2 0年来 ,聚合物 /层状无机物纳米复合材料引起了广泛关注 ,与聚合物材料相比 ,该类纳米复合材料在力学、热稳定性、阻燃、气体阻隔等性能方面都有显著增强 .但所报道的绝大部分无机物均采用蒙脱土为代表的层状硅酸盐[1～ 3] ,而以层状双氢氧化物 (Layered double hydroxide,LDH)为基础制备的聚合物 /层状无机物纳米复合材料的报道极少 .LDH是由水镁石结构中的二价阳离子 (M2 + )被三价阳离子 (M3+ )取代而形成的 ,层上产生的剩余正电荷被吸附在层间的阴离子平衡 .与层状硅酸盐相比 ,L DH层间电荷密度高 ,层与层之间相互作用强 ,导…     

二价金属离子对含铜水滑石结构稳定性的影响

通过构建不同的二价金属离子(M²⁺=Mg²⁺, Ca²⁺, Zn²⁺, Cd²⁺, Ni²⁺, Co²⁺)部分取代铜离子形成CuM₂Al 水滑石(CuM₂Al-LDHs)的周期性模型, 基于密度泛函理论(DFT), 用CASTEP程序模块对周期性模型进行几何全优化和性质计算, 通过分析各体系的结构参数、电子排布、Mulliken 电荷布居、氢键、结合能, 总结出含铜水滑石体系结构的稳定性规律. 计算结果表明: 在CuM₂Al-LDHs 体系中, 主客体间作用力对层板厚度的影响占主要因素; M离子对中心三价铝离子的影响较小, 对二价铜离子的影响较大, 其中价电子均匀排布的M离子对铜的畸变影响小于价电子不均匀排布的M离子. 另外在价电子均匀排布的CuM₂Al-LDHs 体系中, 主客体间的静电作用力和氢键强度逐渐增强. 总体上, 随着M离子周期数的增加, 体系的畸变角增大, 结合能绝对值逐渐减小, 体系的稳定性下降. 价电子不均匀排布的CuCo₂Al-LDHs 体系的稳定性最差. 这有助于从理论上更好地认识含铜水滑石的合成规律.     

阳离子掺杂水滑石的制备及其性质研究

研究了掺杂阳离子水滑石的制备及阳离子对水滑石性质的影响. 分别制备了掺杂Zn2+、Ni2+、Fe3+型的水滑石, 考察了掺杂阳离子对水滑石晶相结构、层间距、层间阴离子含量、水滑石表面形态、水滑石碱性的影响, 结果表明, 由于阳离子的引入, 导致水滑石层间距减小及层间阴离子结合量降低, 且使水滑石培烧产物电负性提高, 并最终降低其碱性. 以上述水滑石培烧产物作为固体碱催化剂促进苯甲醛和丙醛缩合, 合成α-甲基肉桂醛, 关联了水滑石培烧产物碱性与反应活性的关系.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.