The MOF+ Technique: A Significant Synergic Effect Enables High Performance Chromate Removal

A significant synergic effect between a metal–organic framework (MOF) and Fe₂SO₄, the so‐called MOF⁺ technique, is exploited for the first time to remove toxic chromate from aqueous solutions. The results show that relative to the pristine MOF samples (no detectable chromate removal), the MOF⁺ method enables super performance, giving a 796 Cr mg g⁻¹ adsorption capacity. The value is almost eight‐fold higher than the best value of established MOF adsorbents, and the highest value of all reported porous adsorbents for such use. The adsorption mechanism, unlike the anion‐exchange process that dominates chromate removal in all other MOF adsorbents, as unveiled by X‐ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), is due to the surface formation of Fe_0.75Cr_0.25(OH)₃ nanospheres on the MOF samples.     

A protophilic solvent‐assisted solvothermal approach to Cu‐BTC for enhanced CO2 capture

Cu‐BTC–ethylenediamine (EDA)/polyethyleneimine (PEI) adsorbents were synthesized using a protophilic solvent‐assisted solvothermal method. EDA was introduced to enhance the degree of activation due to its lower boiling point allowing it to be removed easily compared with dimethylformamide. A contrast experiment was done by introducing PEI to the solvothermal solution considering its higher boiling point. Powder X‐ray diffraction, scanning electron microscopy and Raman spectroscopic characterizations were performed to investigate the effect of EDA/PEI on crystallinity and morphology of the adsorbents. ¹H NMR characterization and elemental analysis were performed to study the removal rate of organic guest molecules and the degree of activation. Nitrogen physical adsorption and CO₂ adsorption isotherms were used to measure the surface area and CO₂ adsorption capacities. The CO₂ adsorption mechanism of the synthesized adsorbents is mainly dependent on physisorption determined by surface area. Furthermore, open metal sites generated by the enhancement of degree of activation also promote the CO₂ adsorption performance. Therefore, adsorbents synthesized using the protophilic solvent‐assisted solvothermal method exhibit excellent CO₂ adsorption performance. Copyright © 2015 John Wiley & Sons, Ltd.     

Porous carbon derived from a metal–organic framework as an efficient adsorbent for the solid‐phase extraction of phthalate esters

A porous carbon designated as MOF‐5‐C was prepared by directly carbonizing a metal–organic framework (MOF‐5). The morphology and microstructure of MOF‐5‐C were characterized by scanning electron microscopy, N₂ adsorption, and powder X‐ray diffraction. The MOF‐5‐C retained the original porous structures of MOF‐5, and showed a high Brunauer–Emmett–Teller surface area (1808 m² g^?1) and large pore volume (3.05 cm³ g^?1). To evaluate its adsorption performance, the MOF‐5‐C was used as an adsorbent for the solid‐phase extraction of four phthalate esters from bottled water, peach juice, and soft drink samples followed by high‐performance liquid chromatographic analysis. Several parameters that could affect the extraction efficiencies were investigated. Under the optimum conditions, a good linearity was achieved in the concentration range of 0.1–50.0 ng mL^?1 for bottled water sample and 0.2–50.0 ng mL^?1 for peach juice and soft drink samples. The limits of detection of the method (S/N = 3) were 0.02 ng mL^?1 for bottled water sample, and 0.04–0.05 ng mL^?1 for peach juice and soft drink samples. The results indicated that the MOF‐5‐C exhibited an excellent adsorption capability for trace levels of phthalate esters, and it could be a promising adsorbent for the preconcentration of other organic compounds.     

Incorporation of N‐Methyl‐d‐glucamine Functionalized Oligomer into MIL‐101(Cr) for Highly Efficient Removal of Boric Acid from Water

Polymeric resins are practically important adsorbents in a wide variety of applications, but they generally suffer from low surface areas and limited functionalized adsorption sites owing to their closely compacted and tangled polymeric chains. A metal–organic framework (MOF)–polymer composite with enhanced adsorption capacity against the compacted polymeric resins was reported. The strategy to incorporate functionalized oligomer within the cavities of the MOF was demonstrated by the preparation of MIL‐101(Cr) incorporated with N‐methyl‐d ‐glucamine‐based organosiloxane polymer. The resulting MOF composite shows high efficiency for the removal of boric acid from water because of exceptionally high loading of functional groups responsible for the boron adsorption. This material offers promising perspectives for boron removal applications in seawater desalination.     

Facile Synthesis of Hydroxy‐Modified MOF‐5 for Improving the Adsorption Capacity of Hydrogen by Lithium Doping

A facile synthesis of partially hydroxy‐modified MOF‐5 and its improved H₂‐adsorption capacity by lithium doping are reported. The reaction of Zn(NO₃)₂ ? 6 H₂O with a mixture of terephthalic acid (H₂BDC) and 2‐hydroxyterephthalic acid (H₂BDC‐OH) in DMF gave hydroxy‐modified MOF‐5 (MOF‐5‐OH‐x), in which the molar fraction (x) of BDC‐OH^2? was up to 0.54 of the whole ligand. The MOF‐5‐OH‐x frameworks had high BET surface areas (about 3300 m² g^?1), which were comparable to that of MOF‐5. We suggest that the MOF‐5‐OH‐x frameworks are formed by the secondary growth of BDC^2?‐rich MOF‐5 seed crystals, which are nucleated during the early stage of the reaction. Subsequent Li doping into MOF‐5‐OH‐x results in increased H₂ uptake at 77 K and 0.1 MPa from 1.23 to 1.39 wt. % and an increased isosteric heat of H₂ adsorption from 5.1–4.2 kJ mol^?1 to 5.5–4.4 kJ mol^?1.     

A Series of Multifunctional Metal–Organic Frameworks Showing Excellent Luminescent Sensing,Sensitization, and Adsorbent Abilities

A series of highly luminescent‐active metal–organic frameworks (MOFs) 1 – 3 with hierarchical pores have been rationally constructed and fully characterized. The predesigned semi‐rigid hexacarboxylate ligand hexa[4‐(carboxyphenyl)oxamethyl]‐3‐oxapentane acid (H₆L) has been adapted with various space‐directed N donors (i.e., 2,2’‐bipyridine, 4,4′‐di(1H‐imidazol‐1‐yl)‐1,1′‐biphenyl, and 1,3,5‐tri(1H‐imidazol‐1‐yl)benzene) from a bidentate V‐shape to a tridentate Y‐shape. This family of multifunctional MOF materials represents a variety of potential applications in the following aspects: first, as luminescent sensors that show a fast and sensitive detection for pollutant CrO₄^2? and Cr₂O₇^2? ions in aqueous media; second, as adsorbents that can rapidly remove harmful organic dyes; third, as an antenna that can effectively sensitize visible‐light‐emitting Tb³⁺ ions. These multifunctional MOF materials combine optical‐sensing, adsorption, and sensitization properties, thus are very useful in many potential applications. Furthermore, these materials have proved to be reusable.     

Probing of ferrocenylanilines on model micelle/reverse micelle membrane and their enhanced reactivity for reactive oxidants

Reactive oxygen species are formed in the human body but can be removed by suitable antioxidants. In this study we synthesized and characterized three ferrocene derivatives, 4‐ferrocenylaniline (pFA), 3‐ferrocenylaniline (mFA) and 3‐methyl‐4‐ferrocenylaniline (MeFA), having significant potential to be used as antioxidants. The synthesized compounds are insoluble in water, with the solubility of these compounds increasing in micelle solution. The micelle and reverse micelle solutions were considered as model membranes. The synthesized compounds were probed on the model membranes, made by sodium dioctylsulfosuccinate reverse micelle and tetradecyltrimethylammonium bromide micelle, using ¹H NMR spectroscopy. The ¹H NMR results indicated that these compounds are present in the polar region of the model membrane interface. Quantitative measurements showed that mFA has the greatest ability to penetrate into the micelle membrane among these compounds, and pFA is least penetrating in this respect. Solubilization of these compounds in aqueous micelle solution facilitates crystallization (of mFA) and enhances the antioxidant potential of these compounds. X‐ray crystal structure analysis revealed that mFA captures water molecules during crystallization in micelle solution. Their ability to act as antioxidants was evaluated, in dimethylsulfoxide (DMSO) and in micelle solution, using standard 1,1‐ diphenyl‐2‐picrylhydrazyl (DPPH) assay. It was found that their antioxidant potential is good in DMSO and that potential increases on the interface of the model membrane. The highest increase (by 19.6%) in the antioxidant potential, on the model membrane interface, was observed for mFA.     

Biological Chitin–MOF Composites with Hierarchical Pore Systems for Air‐Filtration Applications

Metal–organic frameworks (MOFs) are promising materials for gas‐separation and air‐filtration applications. However, for these applications, MOF crystallites need to be incorporated in robust and manageable support materials. We used chitin‐based networks from a marine sponge as a non‐toxic, biodegradable, and low‐weight support material for MOF deposition. The structural properties of the material favor predominant nucleation of the MOF crystallites at the inside of the hollow fibers. This composite has a hierarchical pore system with surface areas up to 800 m² g⁻¹ and pore volumes of 3.6 cm³ g⁻¹, allowing good transport kinetics and a very high loading of the active material. Ammonia break‐through experiments highlight the accessibility of the MOF crystallites and the adsorption potential of the composite indicating their high potential for filtration applications for toxic industrial gases.     

Preparation of ferric nitrate–graphene nanocomposite and its adsorption of arsenic(V) from simulated arsenic‐containing wastewater

Ferric nitrate–graphene (FG) nanocomposites synthesized via the equivalent‐volume impregnation method were used for the removal of As(V) species from simulated arsenic‐containing wastewater. Effects of various factors were assessed, such as the reaction temperature, solution pH, adsorbent dosage, and reaction time. The results indicated that the As(V) removal efficiency was as high as 99%, and the concentration of arsenic‐containing wastewater after FG treatment was as low as 9.4 μg L^–1 as a result of the optimal absorption capacity and maximum specific surface area (171.766 m²/g) of this material. The equilibrium adsorption capacity of FG for As(V) was achieved in approximately 20 min, and the maximum adsorption capacity was calculated to be 112.4 mg g^–1 by Langmuir adsorption isotherm, which was higher than that of other adsorbents such as manganese‐incorporated iron(III) oxide–graphene (14.42 mg g^–1). Moreover, the removal efficiency of As(V) can be maintained above 95% under acidic and alkaline conditions. Brunauer–Emmett–Teller analysis showed that the modified FG pore structure was regular. Based on the characterizations by X‐ray diffraction, X‐ray photoelectron spectroscopy, and Fourier transform infrared, the products on the surface of the used FG were Fe(OH)₃, FeAsO₄, and other compounds, and As(V) was mainly removed by the formation of insoluble compounds and coprecipitation.     

Structural analysis of interpenetrated methyl‐modified MOF‐5 and its gas‐adsorption properties

The first example of an interpenetrated methyl‐modified MOF‐5 with the formula Zn₄O(DMBDC)₃(DMF)₂, where DMBDC^2? is 2,5‐dimethylbenzene‐1,4‐dicarboxylate and DMF is N,N‐dimethylformamide (henceforth denoted as Me₂MOF‐5‐int ), namely, poly[tris(μ₄‐2,5‐dimethylbenzene‐1,4‐dicarboxylato)bis(N,N‐dimethylformamide)‐μ₄‐oxido‐tetrazinc(II)], [Zn₄(C₁₀H₈O₄)₃O(C₃H₇NO)₂]_n, has been obtained from a solvothermal synthesis of 2,5‐dimethylbenzene‐1,4‐dicarboxylic acid and Zn(NO₃)₂·6H₂O in DMF. A systematic study revealed that the choice of solvent is of critical importance for the synthesis of phase‐pure Me₂MOF‐5‐int , which was thoroughly characterized by single‐crystal and powder X‐ray diffraction (PXRD), as well as by gas‐adsorption analyses. The Brunauer–Emmett–Teller surface area of Me₂MOF‐5‐int (660 m² g^?1), determined by N₂ adsorption, is much lower than that of nonpenetrated Me₂MOF‐5 (2420 m² g^?1). However, Me₂MOF‐5‐int displays an H₂ uptake capacity of 1.26 wt% at 77 K and 1.0 bar, which is comparable to that of non‐interpenetrated Me₂MOF‐5 (1.51 wt%).     

Microwave‐Assisted Synthesis of HKUST‐1 and Functionalized HKUST‐1‐@H3PW12O40: Selective Adsorption of Heavy Metal Ions in Water Analyzed with Synchrotron Radiation

A simple, rapid and efficient synthesis of the metal‐organic framework (MOF) HKUST‐1 [Cu₃(1,3,5‐benzene‐tri‐carboxilic‐acid)₂] by microwave irradiation is described, which afforded a homogeneous and highly selective material. The unusually short time to complete the synthesis by microwave irradiation is mainly attributable to rapid nucleation rather than to crystal growth rate. Using this method, HKUST‐1‐MW (MW=microwave) could be prepared within 20 min, whereas by hydrothermal synthesis, involving conventional heating, the preparation time is 8 h. Work efficiency was improved by the good performance of the obtained HKUST‐1‐MW which exhibited good selective adsorption of heavy metal ions, as well as a remarkably high adsorption affinity and adsorption capacity, but no adsorption of Hg²⁺ under the same experimental conditions. Of particular importance is the preservation of the structure after metal‐ion adsorption, which remained virtually intact, with only a few changes in X‐ray diffraction intensity and a moderate decline in surface area. Synthesis of the polyoxometalate‐containing HKUST‐1‐MW@H₃PW₁₂O₄₀ afforded a MOF with enhanced stability in water, due to the introduced Keggin‐type phosphotungstate, which systematically occluded in the cavities constituting the walls between the mesopores. Different Cu/W ratios were investigated according to the extrusion rate of cooper ions concentration, without significant structural changes after adsorption. The MOFs obtained feature particle sizes between 10–20 μm and their structures were determined using synchrotron‐based X‐ray diffraction. The results of this study can be considered important for potentially wider future applications of MOFs, especially to attend environmental issues.     

Synthesis of Pyrimidine and Pyran Derivatives with the Related Systems and the Study of Their Behavior in the Liquid Solutions

This study aims to synthesis of condensed and non‐condensed heterocyclic rings with long fatty chains as surface active biological compounds. 2‐Cyano‐3‐(dimethylamino)‐N‐octadecylacrylamide ( 5 ) was used to synthesize pyrimidine, pyran, and other condensed products by interacting with appropriate chemical reagents. These compounds were transferred to nonionic surface‐active agents by condensation with propylene oxide. The surface and biological properties showed that these compounds have a high solubility that helps them in easy absorption and adsorption with other compounds. In addition, they have a high ability to decrease the surface tension of the liquids, good wetting, and emulsification power, which can be used at different temperatures without losing their surface or biological properties and enable them for use in industrial and pharmaceutical purposes easily.     

Density Functional Theory Study of Hydrogen Adsorption in a Ti‐Decorated Mg‐Based Metal–Organic Framework‐74

The Ti‐binding energy and hydrogen adsorption energy of a Ti‐decorated Mg‐based metal–organic framework‐74 (Mg‐MOF‐74) were evaluated by using first‐principles calculations. Our results revealed that only three Ti adsorption sites were found to be stable. The adsorption site near the metal oxide unit is the most stable. To investigate the hydrogen‐adsorption properties of Ti‐functionalized Mg‐MOF‐74, the hydrogen‐binding energy was determined. For the most stable Ti adsorption site, we found that the hydrogen adsorption energy ranged from 0.26 to 0.48 eV H₂^?1. This is within the desirable range for practical hydrogen‐storage applications. Moreover, the hydrogen capacity was determined by using ab initio molecular dynamics simulations. Our results revealed that the hydrogen uptake by Ti‐decorated Mg‐MOF‐74 at temperatures of 77, 150, and 298 K and ambient pressure were 1.81, 1.74, and 1.29 H₂ wt %, respectively.     

A Novel Affinity Support Material for the Separation of Immunoglobulin G from Human Plasma

2‐Methacrylamidohistidine (MAH) as a pseudospecific ligand was synthesized from methacryl chloride and histidine. Spherical beads with an average size of 50–63 μm were obtained by the radical suspension polymerization of MAH and 2‐hydroxyethyl methacrylate (HEMA) conducted in an aqueous dispersion medium. Owing to the reasonably rough character of the bead surface, P(HEMA‐co‐MAH) beads had a specific surface area of 17.6 m²·g^–1. Synthesized MAH was characterized by NMR. P(HEMA‐co‐MAH) beads were characterized by swelling studies, FT‐IR spectroscopy, scanning electron microscopy (SEM) and elemental analysis. P(HEMA‐co‐MAH) affinity beads with a swelling ratio of 65% were used in the separation of human immunoglobulin G (HIgG) from aqueous solutions and human plasma. The maximum HIgG adsorption on the P(HEMA‐co‐MAH) adsorbents was observed at pH 7.4 for phosphate and at pH 6.0 for morpholinoethanesulfonic acid buffers. The HIgG adsorption onto the PHEMA adsorbents was negligible. Higher adsorption values (up to 46.5 mg·g^–1) were obtained when the P(HEMA‐co‐MAH) adsorbents were used in aqueous solutions. Much higher amounts of HIgG were adsorbed from human plasma (up to 73.8 mg·g^–1). Adsorption capacities of other blood proteins were obtained as 3.2 mg·g^–1 for fibrinogen and 4.6 mg·g^–1 for albumin. The total protein adsorption was determined to be 82.2 mg·g^–1. The pseudospecific affinity beads allowed one‐step separation of HIgG from human plasma. HIgG molecules could be repeatedly adsorbed and desorbed with these adsorbents without noticeable loss in their HIgG adsorption capacity.     

Well‐Defined Metal–Organic Framework Hollow Nanocages

Metal–organic frameworks (MOFs) have demonstrated great potentials in a variety of important applications. To enhance the inherent properties and endow materials with multifunctionality, the rational design and synthesis of MOFs with nanoscale porosity and hollow feature is highly desired and remains a great challenge. In this work, the formation of a series of well‐defined MOF (MOF‐5, Fe^II‐MOF‐5, Fe^III‐MOF‐5) hollow nanocages by a facile solvothermal method, without any additional supporting template is reported. A surface‐energy‐driven mechanism may be responsible for the formation of hollow nanocages. The addition of pre‐synthesized poly(vinylpyrrolidone)‐ (PVP) capped noble‐metal nanoparticles into the synthetic system of MOF hollow nanocages yields the yolk–shell noble metal@MOF nanostructures. The present strategy to fabricate hollow and yolk–shell nanostructures is expected to open up exciting opportunities for developing a novel class of inorganic–organic hybrid functional nanomaterials.     

螺吡喃功能化UiO-66光响应吸附剂的制备及其性能

将光响应分子甲基螺吡喃SP-CH₃引入UiO-66的非极性孔笼中,构筑吸附活性位可光控调节的光响应吸附剂。SP-CH₃功能化的吸附剂完好保留了载体UiO-66的骨架和孔道结构。以阴离子染料甲基橙为探针,研究了吸附剂在不同光照条件下的吸附和解吸性能。结果表明,经紫外光照后,吸附剂对甲基橙的吸附量为41.99 mg·g^-1,相较于可见光照后样品的吸附量提升57.56%,吸附作用增强;经可见光照后,甲基橙的脱附量为81.6%。本策略通过光照刺激改变UiO-66孔笼中SP-CH₃的构型及表面电荷性质,即对吸附活性位进行光控调节,在不同光照条件下实现对吸附质的高效吸附和有效脱附。     

Template‐based Synthesis of a Formate Metal–Organic Framework/Activated Carbon Fiber Composite for High‐performance Methane Adsorptive Separation

Simultaneous improvement in adsorption selectivity and capacity for single adsorbents is challenging but counting for much in adsorptive separations. To this end, a formate metal–organic framework and activated carbon fiber composite was synthesized in our work by a simple two‐step process, involving homogeneous precipitation of a MOF precursor on an activated carbon fiber and subsequent template replication. The resultant core–shell composite, ACF@[Ni₃(HCOO)₆], exhibited optimized adsorption performance both in selectivity and capacity for the separation of CH₄/N₂ to most of state‐of‐the‐art adsorbents.     

螺吡喃功能化UiO-66光响应吸附剂的制备及其性能

将光响应分子甲基螺吡喃SP-CH₃引入UiO-66的非极性孔笼中,构筑吸附活性位可光控调节的光响应吸附剂。SP-CH₃功能化的吸附剂完好保留了载体UiO-66的骨架和孔道结构。以阴离子染料甲基橙为探针,研究了吸附剂在不同光照条件下的吸附和解吸性能。结果表明,经紫外光照后,吸附剂对甲基橙的吸附量为41.99 mg·g^-1,相较于可见光照后样品的吸附量提升57.56%,吸附作用增强;经可见光照后,甲基橙的脱附量为81.6%。本策略通过光照刺激改变UiO-66孔笼中SP-CH₃的构型及表面电荷性质,即对吸附活性位进行光控调节,在不同光照条件下实现对吸附质的高效吸附和有效脱附。     

MOF‐5‐Polystyrene: Direct Production from Monomer,Improved Hydrolytic Stability,and Unique Guest Adsorption

An unprecedented mode of reactivity of Zn₄O‐based metal–organic frameworks (MOFs) offers a straightforward and powerful approach to polymer‐hybridized porous solids. The concept is illustrated with the production of MOF‐5‐polystyrene wherein polystyrene is grafted and uniformly distributed throughout MOF‐5 crystals after heating in pure styrene for 4–24 h. The surface area and polystyrene content of the material can be fine‐tuned by controlling the duration of heating styrene in the presence of MOF‐5. Polystyrene grafting significantly alters the physical and chemical properties of pristine MOF‐5, which is evident from the unique guest adsorption properties (solvatochromic dye uptake and improved CO₂ capacity) as well as the dramatically improved hydrolytic stability of composite. Based on the fact that MOF‐5 is the best studied member of the structure class, and has been produced at scale by industry, these findings can be directly leveraged for a range of current applications.     

Partially Pyrolyzed Binary Metal–Organic Framework Nanosheets for Efficient Electrochemical Hydrogen Peroxide Synthesis

Herein, we developed a partially controlled pyrolysis strategy to create evenly distributed NiO nanoparticles within NiFe‐MOF nanosheets (MOF NSs) for electrochemical synthesis of H₂O₂ by a two‐electron oxygen reduction reaction (ORR). The elemental Ni can be partially transformed to NiO and uniformly distributed on the surface of the MOF NSs, which is crucial for the formation of the particular structure. The optimized MOF NSs‐300 exhibits the highest activity for ORR with near‐zero overpotential and excellent H₂O₂ selectivity (ca. 99 %) in 0.1 m KOH solution. A high‐yield H₂O₂ production rate of 6.5 mol g_cat^?1 h^?1 has also been achieved by MOF NSs‐300 in 0.1 m KOH and at 0.6 V (vs. RHE). In contrast to completely pyrolyzed products, the enhanced catalytic activities of partially pyrolyzed MOF NSs‐300 originates mainly from the retained MOF structure and the newly generated NiO nanoparticles, forming the coordinatively unsaturated Ni atoms and tuning the performance towards electrochemical H₂O₂ synthesis.