配位-氧化聚合-水热法制备聚苯胺/CoFe_2O_4纳米复合物及其微波吸收性能

采用"配位-氧化聚合-水热法"制备了本征态聚苯胺/CoFe2O4二元纳米复合物,再以磺基水杨酸掺杂获得聚苯胺/CoFe2O4电磁复合物.考察了反应物配比及掺杂酸浓度对产物电磁性能的影响.通过透射电子显微镜(TEM)、X射线衍射(XRD)、红外光谱(FTIR)及电磁测量等手段对聚苯胺/CoFe2O4的形貌、结构及性能进行了表征.结果表明,复合物呈现多级结构,其中CoFe2O4为立方体状,平均粒径小于20 nm.当CoFe2O4的质量分数为8.86%时,复合物的电导率约为0.43 S/cm;当聚苯胺/CoFe2O4复合物厚度为2 mm时,在16.01 GHz处最大反射损耗为-16.71 dB,小于-10 dB的带宽达4.68 GHz;而当聚苯胺/CoFe2O4复合物厚度为3.2 mm时,在9.23 GHz处最大反射损耗达-51.81 dB,小于-10 dB的带宽为3.69 GHz,表明具有良好的吸波性能.     

鳞状CoMn_2O_4/石墨烯复合材料的制备及在超级电容器中的应用

通过简单的共沉淀反应和热处理过程在还原氧化石墨烯(rGO)表面生长鳞状锰酸钴(CoMn_2O_4)纳米片,得到了CoMn_2O_4/rGO复合材料.通过场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、X射线衍射(XRD)以及X射线光电子能谱(XPS)对样品的结构和组成进行了表征.电化学性能测试结果表明,CoMn_2O_4/rGO具有较好的储能性能和优良的循环稳定性.当电流密度为2 A/g时,CoMn_2O_4/rGO的比电容可达1000.8 F/g.经过1000周充放电循环后比电容保持率为93.6%.     

锂离子电池用α-Fe2O3-Ag复合纳米棒负极材料的制备及储锂性能

采用FeOOH纳米棒为前驱体,通过层层自组装法及随后的热处理过程制备出α-Fe2O3-Ag复合纳米棒.采用透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)和电化学性能测试对样品的形貌、结构及电化学性能进行了表征.结果表明,Ag纳米颗粒均匀地分布在α-Fe2O3纳米棒的表面.作为锂离子电池负极材料,α-Fe2O3-Ag复合纳米棒表现出了较好的循环性能和较高的比容量.180个循环后,其比容量高达549.8 mA.h/g.     

溶胶-凝胶法制备In-Cd纳米复合氧化物及其气敏性能研究

采用溶胶凝胶法制备了In20rCdln2O4和CdO-Cdln2O4纳米复合氧化物,利用扫描电子显微镜(SEM)和X射线衍射仪(XRD)对复合材料的形貌和结构进行表征,并对其进行了乙醇、丙酮等多种气体的气敏性能测试.结果表明Cdln2O4材料复合h12O3和CdO后显著提高了对丙酮和乙醇气体的灵敏度和选择性.     

磁电CoFe2O4/BaTiO3纳米管的溶胶-凝胶模板法合成和表征

用溶胶-凝胶模板法合成了CoFe2O4/BaTiO3(CFO/BTO)复合纳米管, 管的直径约为100、200和300 nm, 其长度约为100 μm. X射线衍射(XRD)和选区电子衍射(SAED)都显示复合纳米管中同时存在尖晶石相的CoFe2O4 (CFO)和钙钛矿相的BaTiO3(BTO), 进一步的透射电子显微镜(TEM)研究证实合成的纳米复合物具有明显的管状结构. 磁、电研究表明, 该复合纳米管的磁性与纯CFO纳米管的磁性相当; 而铁电性与纯BTO纳米管的铁电性相当.     

导电聚苯胺与磁性CoFe2O4纳米复合物的制备与表征

在利用HNO3酸化处理CoFe2O4磁性纳米粒子使其表面离子化、分散性得到改善的基础上, 采用原位聚合法制备了具有电磁功能的聚苯胺/CoFe2O4 (PANI/CoFe2O4)纳米复合物. 借助TEM, XRD, FT-IR, TG, 四探针电导率仪、VSM(振动样品磁强计)等分析手段研究了复合物的形貌、结构、热稳定性及电磁性能. 结果表明, 处理过的CoFe2O4磁性纳米粒子可形成分散均匀的PANI/CoFe2O4纳米复合物, CoFe2O4以25 nm左右的粒子分散于聚苯胺基体中; PANI与CoFe2O4之间存在化学键合作用, 正是这种作用使复合物热稳定性得以提高; 复合物同时具有导电性和磁性能, 且随CoFe2O4含量变化而变化.     

磁性TiO2/CoFe2O4纳米复合光催化材料的制备

以磁性CoFe2O4为核,采用改进的溶胶-凝胶法,制备了磁性TiO2/CoFe2O4纳米复合光催化材料.利用VSM(振动样品磁强计)技术对其磁性能进行了研究,结果表明:由该法所得的TiO2/CoFe2O4纳米复合光催化材料的饱和磁化强度虽稍弱于纯CoFe2O4纳米材料,但其矫顽力则优于CoFe2O4.TEM、XRD、UV-Vis等的结果表明,该纳米复合材料中的TiO2为锐钛矿结构;与TiO2相比,纳米复合材料对光的吸收拓展到了整个紫外-可见区,且吸收强度大大增强.对染料废水光催化降解的模拟研究表明,该复合材料在紫外光下,6 h可以使亚甲基蓝染料溶液的脱色率达95%,且重复使用3次时染料溶液的脱色率仍能保持在90%,明显优于纯TiO2.     

水热法制备Fe3O4/rGO纳米复合物作为锂离子电池阳极材料

以氢氧化铁为四氧化三铁的前驱体,氧化石墨烯（GO）为还原石墨烯（rGO）的前驱体,以水合肼和二水合柠檬酸三钠为混合还原剂,采用水热法制备了还原石墨烯负载四氧化三铁纳米颗粒（Fe₃O₄/rGO）的复合材料。通过透射电子显微镜（TEM）、X-射线衍射（XRD）和热重分析（TGA）对产物的形貌、结构和组成进行了表征。以锂片为对电极进行了扣式电池的组装,通过恒电流充放电和循环伏安法对其电化学性能进行了测试。材料具有均一的形貌,rGO具有较高的还原程度且可以在充放电过程中缓冲Fe₃O₄纳米颗粒的体积变化,使得Fe₃O₄/rGO纳米复合物具有较好的电化学性能。     

含Ce水滑石基复合氧化物对混合染料的光催化性能

将具有光催化活性的Ce O_2和锌锡水滑石进行复合,经焙烧得到光催化性能较高的Ce O_2/Zn O/Sn O_2复合氧化物。通过X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见漫反射图谱(UV-Vis DRS)技术对样品的晶体结构、表面形貌和光学性能进行表征,并利用密度泛函理论(DFT)计算样品的态密度,分析其电子能态结构。以甲基橙(MO)和亚甲基蓝(MB)的混合溶液(C_(MO)∶C_(MB)=1∶1)模拟染料废水,研究Ce O_2含量和焙烧温度对复合氧化物光催化降解混合染料的影响。结果表明:随着Ce O_2含量和焙烧温度的增加,复合氧化物的结晶度及对MO和MB的光催化活性得到增强;同时,复合氧化物对混合染料中MO的降解率优于MB。其中Ce O_2含量为20%,焙烧温度为700℃时的复合氧化物表现出最佳的光催化性能,对混合染料中MO和MB的降解率分别达到96.7%和95.0%。结合实验结果和理论计算,推测了混合染料中MO和MB的降解路径。     

磁电CoFe2O4/BaTiO3纳米管的溶胶-凝胶模板法合成和表征

用溶胶-凝胶模板法合成了 CoFe2O4)/BaTiO3(CFO/BTO)复合纳米管,管的直径约为 100、200 和 300 nm,其长度约为100 μm.x射线衍射(xRD)和选区电子衍射(sAED)都显示复合纳米管中同时存在尖晶石相的CoFe2O4(CFO)和钙钛矿相的 BaTiO3(BTO),进一步的透射电子显微镜(TEM)研究证实合成的纳米复合物具有明显的管状结构.磁、电研究表明,该复合纳米管的磁性与纯 CFO 纳米管的磁性相当;而铁电性与纯BTO纳米管的铁电性相当.     

NF/rGO/Co_3O_4/NiO电极的制备及在超级电容器中的应用

以泡沫镍(NF)为集流体,在优化好的电位、时间和浓度下,将还原氧化石墨烯(rGO)、金属氧化物(Co_3O_4和NiO)直接生长在泡沫镍上,制备了NF/rGO/Co_3O_4和NF/rGO/Co_3O_4/NiO电极.运用三电极体系对电极材料进行了恒流充放电(GCD)和交流阻抗(EIS)等测试.结果表明,复合材料NF/rGO/Co_3O_4/NiO具有较高的比容量(电流密度为2 A/g时,比容量达到1188.6 F/g)和较好的循环稳定性(2000周充放电后,稳定性达到80.5%).该材料还具有较高的倍率性能,当电流密度由2 A/g增至12 A/g时,倍率性能仍能达到75.7%.     

石墨烯修饰Y型TiO2纳米管光电极制备及其对氨氮催化氧化性能

采用三步阳极氧化法和一步循环伏安电沉积法制备了还原氧化石墨烯（rGO）修饰的Y型TiO₂纳米管阵列（rGO/Y-TiO₂ NTs）电极。通过场发射电子扫描显微镜（FESEM）、能量色散X荧光光谱（EDX）、X射线衍射（XRD）、紫外可见漫反射光谱（UV-Vis）及拉曼光谱（Raman）等对电极样品进行了表征。以rGO/Y-TiO₂ NTs电极为光阳极,测试了不同循环伏安沉积圈数对电极光电流响应的影响,考察了在1.0 V偏压下电极对氨氮的光电催化氧化性能。结果表明,高度有序的Y-TiO₂ NTs为锐钛矿型,具有大的比表面积,表面修饰平滑透明rGO薄膜后可显著提高其光电催化效率,沉积圈数为30时电极在30 min内对氨氮的光电催化氧化效率为95.9%。     

石墨烯修饰Y型TiO_2纳米管光电极制备及其对氨氮催化氧化性能

采用三步阳极氧化法和一步循环伏安电沉积法制备了还原氧化石墨烯(rGO)修饰的Y型TiO_2纳米管(rGO/Y-TiO_2NTs)电极。通过场发射电子扫描显微镜(FESEM)、X射线能谱(EDS)、X射线衍射(XRD)、紫外可见漫反射光谱(UV-Vis DRS)及拉曼光谱(Raman)等对电极样品进行了表征。以rGO/Y-TiO_2NTs电极为光阳极,测试了不同循环伏安沉积圈数对电极光电流响应的影响,考察了在1.0 V偏压下电极对氨氮的光电催化氧化性能。结果表明,高度有序的Y-TiO_2NTs为锐钛矿型,具有大的比表面积,表面修饰平滑透明rGO薄膜后可显著提高其光电催化效率,沉积圈数为30时电极在30 min内对氨氮的光电催化氧化效率为95.9%。     

Fabrication of Trimetallic Pt−Pd−Co Porous Nanostructures on Reduced Graphene Oxide by Galvanic Replacement: Application to Electrocatalytic Oxidation of Ethylene Glycol

In present work, reduced graphene oxide nanosheets (rGO) decorated with trimetallic three‐dimensional (3D) Pt−Pd−Co porous nanostructures was fabricated on glassy carbon electrode (Pt−Pd−Co/rGO/GCE). First, GO suspension was drop‐casted on the electrode surface, then GO film reduction was carried out by cycling the potential in negative direction to form the rGO film modified GCE (rGO/GCE). Then, electrodeposition of the cobalt nanoparticles (CoNPs) as sacrificial seeds was performed onto the rGO/GCE by using cyclic voltammetry. Afterward, Pt−Pd−Co 3D porous nanostructures fabrication occurs through galvanic replacement (GR) method based on a spontaneous redox process between PtCl₂, PdCl_2, and CoNPs. The morphology and structure of the Pt−Pd−Co/rGO porous nanostructure film was characterized by scanning electron microscopy, energy dispersive spectroscopy and X‐ray diffraction method. The performance of the prepared electrode was investigated by various electrochemical methods including, cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalytic activity of the as‐prepared modified electrode with high surface areas was evaluated in anodic oxidation of ethylene glycol. The study on electrocatalytic performances revealed that, in comparison to various metal combinations in modified electrodes, trimetallic Pt−Pd−Co/rGO/GCE exhibit a lower onset potential, significantly higher peak current density, high durability and stability for the anodic oxidation of ethylene glycol. The excellent performances are attributed to the rGO as catalysts support and resulting synergistic effects of the trimetallic and appropriate characteristics of the resulted 3D porous nanostructures. Moreover, the influence of various concentrations of ethylene glycol, the potential scan rate and switching potential on the electrode reaction, in addition, long‐term stability have been studied by chronoamperometric and cyclic voltammetric methods.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

还原氧化石墨烯改性少层剥离石墨增强石墨基钾离子电池负极稳定性

钾在石墨中嵌入电位较低,因此石墨负极可使钾离子电池具有较高的能量密度,是一种理想的钾离子电池负极材料。然而,石墨嵌钾后的体积膨胀率高达60%,导致钾离子电池的循环稳定性较差。此外,钾嵌入石墨层间的动力学过程缓慢,制约了钾离子电池倍率性能的提升。在本工作中,我们用还原氧化石墨烯(rGO)包覆剥离石墨(EG),得到一种具有协同效应的层状复合材料。一方面,以少层的EG代替石墨可以减少由于钾的嵌入/脱嵌所引起的体积膨胀和内部应力;另一方面,外层rGO可以避免EG的堆叠,这有利于加速动力学过程并在钾化/去钾化过程中稳定结构。当复合材料所用EG和GO的质量比为1 : 1时,其性能达到最优,在50 mA·g^-1的电流密度下能够提供443 mAh·g^-1的比容量;在电流密度为800 mA·g^-1时,比容量为190 mAh·g^-1,保持率为42.9%。相同测试条件下,纯EG和rGO的容量保持率仅为14.2%和27.2%。测试结果说明EG-1/rGO-1复合材料在比容量和倍率性能两个方面得到了提升。     

Synthesis and Electrochemical Performance of Electrostatic Self-Assembled Nano-Silicon@N-Doped Reduced Graphene Oxide/Carbon Nanofibers Composite as Anode Material for Lithium-Ion Batteries

Silicon-carbon nanocomposite materials are widely adopted in the anode of lithium-ion batteries (LIB). However, the lithium ion (Li⁺) transportation is hampered due to the significant accumulation of silicon nanoparticles (Si) and the change in their volume, which leads to decreased battery performance. In an attempt to optimize the electrode structure, we report on a self-assembly synthesis of silicon nanoparticles@nitrogen-doped reduced graphene oxide/carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for LIB through electrostatic attraction. A large number of vacancies or defects on the graphite plane are generated by N atoms, thus providing transmission channels for Li⁺ and improving the conductivity of the electrode. CNF can maintain the stability of the electrode structure and prevent Si from falling off the electrode. The three-dimensional composite structure of Si, N-doped rGO, and CNF can effectively buffer the volume changes of Si, form a stable solid electrolyte interface (SEI), and shorten the transmission distance of Li⁺ and the electrons, while also providing high conductivity and mechanical stability to the electrode. The Si@N-doped rGO/CNF electrode outperforms the Si@N-doped rGO and Si/rGO/CNF electrodes in cycle performance and rate capability, with a reversible specific capacity reaching 1276.8 mAh/g after 100 cycles and a Coulomb efficiency of 99%.     

Three-Dimensional Nickel-Nickel Oxide Core-Shell Nanorod Array for Nonenzymatic Glucose Sensing

Nickel-nickel oxide core-shell nanorod array electrodes were fabricated and a preliminary application for nonenzymatic glucose determination exhibited excellent performance. The nanorod array electrode was synthesized for the first time by an anodic aluminum oxide template assisted electrochemical deposition technique. Facile oxidation was employed to convert nickel at the outer surface of the nanorods to nickel oxide, resulting in a nickel-nickel oxide core-shell nanorod array. The successful conversion was confirmed by x-ray diffraction, cyclic voltammetry, and scanning electron microscopy. The modified electrode possessed high surface area contributed by the nanorods, and efficient mass transfer due to the wide internanorod gap. The electrode provided high sensitivity (127 microampere square centimeter per millimolar), a low limit of detection (～0.5 micromolar), and a long linear dynamic range (up to 14 millimolar) for the determination of glucose. Accurate determination of glucose in human serum was performed. This synthetic strategy may have further application for the preparation of high surface area thin-film electrodes for a variety of applications.     

Free‐standing and Flexible MoS2/rGO Paper Electrode for Amperometric Detection of Folic Acid

The development of flexible electrodes is of considerable current interest because of the increasing demand for modern electronics, portable medical products, and compact devices. We report a new type of flexible electrochemical sensor fabricated by integrating graphene and MoS₂ nanosheets. A highly flexible and free‐standing conductive MoS₂ nanosheets/reduced graphene oxide (MoS₂/rGO) paper was prepared by a two‐step process: vacuum filtration and chemical reduction treatment. The MoS₂/graphene oxide (MoS₂/GO) paper obtained by a simple filtration method was transformed into MoS₂/rGO paper after a chemical reduction process. The obtained MoS₂/rGO paper was characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy, electrochemical impedance spectroscopy. The electrochemical behavior of folic acid (FA) on MoS₂/rGO paper electrode was investigated by cyclic voltammetry and amperometry. Electrochemical experiments indicated that flexible MoS₂/rGO composite paper electrode exhibited excellent electrocatalytic activity toward the FA, which can be attributed to excellent electrical conductivity and high specific surface area of the MoS₂/rGO paper. The resulting biosensor showed highly sensitive amperometric response to FA with a wide linear range.     

Electrochemical sensor for ultrasensitive determination of ceftazidime using hollow platinum nanoparticles/reduced graphene oxide/pencil graphite electrode

In this paper, an electrochemical sensor was prepared based on the modification of pencil graphite electrode (PGE) by hollow platinum nanoparticles/reduced graphene oxide (HPtNPs/rGO/PGE) for determination of ceftazidime (CFZ). Initially, rGO was electrodeposited on the electrode surface, and then, hollow platinum nanoparticles were placed on the electrode surface via galvanic displacement reaction of Pt(IV) ions with cobalt nanoparticles (CoNPs) that had electrodeposited on the electrode surface. Several significant parameters controlling the performance of the HPtNPs/rGO/PGE were examined and optimized using central composite design as one optimization methodology. The surface morphology and elemental characterization of the bare PGE, rGO/PGE, CoNPs/rGO/PGE, and HPtNPs/rGO/PGE-modified electrodes was analyzed by field-emission scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electrochemical impedance spectroscopy. The electrochemical activity of CFZ on resulting modified electrode was investigated by cyclic voltammetry (CV) and adsorptive differential pulse voltammetry (AdDPV). Adsorptive differential pulse voltammetry indicates that peak current increases linearly with respect to increment in CFZ concentration. CFZ was determined in the linear dynamic range of 5.0 × 10^?13 to 1.0 × 10^?9 M, and the detection limit was determined as 2.2 × 10^?13 M using AdDPV under optimized conditions. The results showed that modified electrode has high selectivity and very high sensitivity. The method was used to determine of CFZ in drug injection and plasma samples.