脉冲电化学驱动壳聚糖原位调控制备羟基磷灰石/银复合涂层

采用脉冲电化学驱动壳聚糖原位调控制备了具有抗菌性的羟基磷灰石/银纳米复合涂层.考察了电解液中银离子浓度、钙磷盐浓度等对复合涂层的形貌及成分的影响.探讨了壳聚糖调控羟基磷灰石和银纳米粒子的形成机理,发现在本研究的较佳实验条件为电位-1.3 V,Ag~+浓度为0.06 g·L~(-1),Ca~(2+)浓度为5 mmol·L~(-1).在此基础上对复合涂层的生物活性、生理稳定性能、抗菌性能进行分析.结果表明:复合涂层呈纳米球状,由羟基磷灰石、银、壳聚糖三相组成,并且表面有一层壳聚糖覆盖.银纳米粒子和羟基磷灰石纳米粒子在复合涂层中均匀分布.将复合涂层浸泡在SCPS溶液中37°C浸泡矿化10天后,在复合涂层表面生产细针状排列整齐的羟基磷灰石,且在(002)晶面25.8°处发生显著择优生长,表明复合涂层在快速矿化液中能诱导磷灰石生成,生物活性好.将复合涂层浸泡在37°C PBS溶液中考察其生理稳定性,壳聚糖对复合涂层中Ca~(2+)和Ag~+实现双重离子释放,且降低了离子释放速度,涂层具有良好的生理稳定性.抗菌实验表明复合涂层对大肠杆菌和金黄色葡萄球菌抗菌率达到99%以上,抗菌能力强.     

原位沉淀法制备CS/nHA多孔复合支架及其性能

通过原位沉淀法和冷冻相分离技术得到含有钙磷前驱体(CaP)的初始多孔支架, 利用多孔支架表面原位生成的壳聚糖(CS)膜减缓NaOH溶液中OH^-离子的渗透速率, 以达到纳米羟基磷灰石(nHA)缓慢形成的目的, 从而制得nHA 分布均匀的CS/nHA多孔复合支架. 利用扫描电镜(SEM)和万能试验机研究复合支架的结构和性能, 发现nHA为针状结构, 长度为80200 nm, 宽度为2050 nm. 随着nHA含量的增加, 复合支架的孔隙率下降, 由(93.8±3.3)%降至(87.7±3.8)%, 压缩强度则逐渐提高, 由(0.5±0.09) MPa增加至(1.5±0.06) MPa. 当复合支架中nHA质量分数为25%时, 未发现nHA团聚现象, nHA均匀地分布于CS基体中. 通过红外光谱(FTIR)、 X射线衍射(XRD)及X射线光电子能谱(XPS)等分析推断, nHA与CS之间可能存在配位和氢键作用. 细胞实验结果表明, CS/nHA多孔复合支架具有良好的生物相容性, 细胞在支架内部贴壁黏附生长. CS/nHA多孔复合支架有望在骨组织工程领域具有良好的应用前景.     

钛基多孔HA/SiO2复合涂层的制备及性能研究

为了制得表面多孔且与基材结合强度高的羟基磷灰石(HA)涂层,实验中以正丁醇为分散介质,以SiO2粉末为添加剂,纯钛片为基材,电泳沉积制备羟基磷灰石/二氧化硅/壳聚糖/(HA/SiO2/CS)复合涂层,经后续热处理得到多孔HA/SiO2复合涂层,采用扫描电镜(SEM)、傅立叶红外光谱仪(FT-IR)、X射线衍射仪(XRD)、万能材料试验机对涂层的表面形貌、组成、结构和结合强度进行测试和表征,并通过模拟体液(SBF)浸泡法对复合涂层的生物活性进行评价.结果表明:当悬浮液中的HA/SiO2/CS质量比为1∶1∶1时,制得的HA/SiO2/CS涂层经700℃热处理后获得的HA/SiO2复合涂层孔洞分布均匀,大孔孔径在10～15μm,小孔孔径在1～5μm;涂层与基材的结合强度达到25.5 MPa;多孔HA/SiO2复合涂层在SBF中浸泡7 d后,涂层表面碳磷灰石化;说明实验中添加SiO2所制得的多孔HA/SiO2复合涂层与钛基材结合强度高,且具有良好的生物活性.     

成骨肿瘤细胞在纳米氧化钛陶瓷表面的生物活性研究

以羟基磷灰石和氧化镁为晶粒生长抑制剂制备的纳米氧化钛陶瓷为研究对象, 采用体外成骨细胞Ros17/28与材料复合培养的方法, 通过MTT法、荧光染色法和SEM细胞形貌观察等手段综合判断细胞在材料表面的活性, 以此评价纳米氧化钛陶瓷的生物活性. 结果表明, 以羟基磷灰石为晶粒生长抑制剂的氧化钛陶瓷晶体颗粒尺寸达到纳米级, 其生物活性超出了以氧化镁为晶粒生长抑制剂的氧化钛陶瓷和纯羟基磷灰石陶瓷, 具有优异的生物相容性, 是生物活性陶瓷.     

改性羟基磷灰石/聚乳酸纳米复合材料的结晶行为

利用溶剂复合的方法制备了具有良好生物相容性的表面接枝聚(γ-苄基-L-谷氨酸)的改性羟基磷灰石/聚乳酸纳米复合材料, 并研究了其熔融与结晶行为. 结果表明, 聚乳酸的玻璃化转变温度为60.3 ℃, 而复合材料的玻璃化转变温度达到65.8 ℃, 不同样品在140 ℃等温结晶后, 改性羟基磷灰石/聚乳酸复合材料的球晶直径仅为聚乳酸(PLLA)球晶直径的16.7%~66.7%. 复合材料的熔点提高到184.4 ℃.     

聚L-乳酸/二氧化硅纳米复合材料及其表面诱导生成类骨磷灰石的制备

为改善纳米SiO2粒子在聚L-乳酸基体中的分散性, 将乳酸齐聚物接枝到纳米SiO2粒子表面, 通过IR, 29Si MAS NMR和TGA对改性SiO2进行表征. 以聚L-乳酸(PLLA)为基体, 加入乳酸齐聚物接枝改性的二氧化硅(g-SiO2)粒子, 采用溶液浇铸法制备PLLA/g-SiO2纳米复合材料, 测试其在模拟体液(SBF)中的生物活性. 通过XRD, IR, SEM和EDS表征手段, 考察材料表面类骨磷灰石形成能力. 结果表明, 乳酸齐聚物成功地接枝到SiO2表面, 当反应36 h时, g-SiO2接枝率最大(9.22%). 随着g-SiO2含量增加和浸泡时间的延长, 材料表面最初形成的无定形沉积物矿化成碳酸羟基磷灰石(Carbonated hydroxyapatite, CHA), 钙磷比为1.72, 类似于人骨无机质, 表明g-SiO2的引入能明显加速复合材料表面CHA沉积, 该复合材料有望成为骨修复填充材料和组织工程支架材料.     

羟基磷灰石/氧化铁复合涂层的制备及其诱导骨生长的生物活性

用电泳沉积法制得羟基磷灰石/壳聚糖/氧化铁(HA/CS/Fe2O3)复合涂层,经700 ℃烧结处理得到HA/Fe2O3复合涂层。 通过SEM、EDS、XRD、FT-IR、电化学和万能材料试验机等对复合涂层的表面形貌、物相组成、抗腐蚀性和结合强度进行了表征和测试,最后采用1.5SBF浸泡法对复合涂层的生物活性进行了评价。 结果表明,当悬浮液中的HA、CS与Fe2O3质量比为100∶100∶1时,所制得的HA/Fe2O3复合涂层表面粗糙,抗腐蚀性强,具有良好的诱导骨生长生物活性,基体与复合涂层结合强度可达27.5 MPa。     

生物活性复合材料在生物矿化过程中的微观形貌与离子浓度变化

采用3-羟基丁酸酯-3-羟基戊酸酯的共聚物(PHBV)与磷酸三钙(TCP)、羟基磷灰石(HA)、生物活性玻璃(BG)等进行复合,获得了性能优良的生物活性骨组织工程支架材料和骨修复材料.研究和比较了3种复合材料在体外模拟生理环境中发生的生物矿化反应,对比了反应前后因矿化物的形成导致的表面微观形貌的变化,通过检测反应液离子浓度的变化对不同材料的矿化过程和生物活性进行了定量表征.研究结果表明,3种复合材料在模拟生理溶液中发生生物矿化的过程和程度不同,其中PHBV/BG的生物活性反应最为明显.     

基于纳米羟基磷灰石溶胶的nHA/PA66复合粉体制备与表征

本文开发了一种新的制备纳米羟基磷灰石(nHA)/聚酰胺66(PA66)复合材料的方法。先用明胶包覆nHA棒状颗粒,再将其制备成以N,N-二甲基乙酰胺和甘油的混合液为溶剂的稳定溶胶。当nHA溶胶与PA66溶液混合时,相同的酰胺基团保证了二者之间良好的共混相容性,成功制备了nHA/PA66复合材料。X射线衍射(XRD)、傅立叶红外光谱分析(FTIR)、透射电镜(TEM)、扫描电镜-能谱分析(SEM-EDS)以及差热分析(DTA)和热重分析(TG)等表征了产物的形貌、结构及成分分布。结果表明：明胶对nHA颗粒具有显著的化学包覆作用,使nHA溶胶与PA66溶液得以均匀混合,均匀分布在PA66基体中,二者以氢键结合为一体。     

原位复合法制备层状结构的壳聚糖/羟基磷灰石纳米材料

用原位复合法制备了高性能的壳聚糖/羟基磷灰石(CS/HA)纳米复合材料.用预先沉积的壳聚糖膜将含有羟基磷灰石前驱体的壳聚糖溶液与凝固液隔离,同时控制壳聚糖沉积与羟基磷灰石前驱体转化为羟基磷灰石的过程,使其缓慢且有序地进行.当pH值改变时,质子化的壳聚糖分子链在负电层诱导下有序沉积并形成层状结构与羟基磷灰石原位生成CS/HA,并实现二者分子级复合.XRD和TEM测试证实原位生成的磷酸盐是羟基磷灰石,且其颗粒长约为100nm,宽30～50nm.SEM结果表明,用原位复合法制备的材料具有层状结构,CS/HA(质量比100/5)纳米复合材料弯曲强度高达86MPa,比松质骨的高3～4倍,相当于密质骨的1/2,有望用于可承重部位的组织修复材料.     

In situ biomimetic formation of nano‐hydroxyapatite crystals on chitosan microspheres

Chitosan (CS) is a biocompatible, noncytotoxic biomaterial used before as base material for composites. On the other hand, nano‐hydroxyapatite (nHA) is one of the main components of human bones, highly used for biomedical applications. In this work, CS microspheres were produced under a W/O emulsion system. CS microspheres with calcium ions were then exposed to Na₃PO₄ solution. In situ biomimetic nHA crystals were formed on CS microspheres to generate 15.14 ± 3.15‐μm composite microspheres. The microspheres were subsequently seeded with MG63 osteoblasts to observe their cell responses. All microspheres were characterized via scanning electron microscopy (SEM), phase‐contrast photomicroscopy, and X‐ray diffraction (XRD) analysis. The results showed flake‐like shape and islet‐like growth of nHA depositions presented on the surface of the CS microspheres. In vitro tests indicated that the CS/nHA microparticles were not only biocompatible but also enhanced cell adhesion and elongation due to the in situ biomimetic synthesis method.     

聚乙二醇/羟基磷灰石纳米杂化材料的制备及表征

以聚乙二醇单甲醚(MPEG)为原料, 采用先磷酰化再水解的方法合成了聚乙二醇单甲醚磷酸酯(P-MPEG). 以P-MPEG为空间位阻剂, 采用共沉淀法合成了内核为纳米羟基磷灰石(nHA)、 壳层为MPEG链的纳米杂化材料. 用傅里叶变换红外光谱(FTIR)、 X射线衍射(XRD)、 透射电子显微镜(TEM)和激光粒度分析(LPSA)对材料结构进行了表征. 结果表明, 所合成的杂化材料不仅能在水中再分散, 而且可以在甲醇和二甲基甲酰胺(DMF)等有机溶剂中再分散.     

Preparation and characterization of novel crown ether functionalized ionic liquid-based solid-phase microextraction coatings by sol-gel technology

A novel crown ether functionalized ionic liquid (IL), 1-allyl-3-(6'-oxo-benzo-15-crown-5 hexyl) imidazolium hexafluorophosphate was synthesized and used as selective stationary phase to prepare task-specific IL-based solid phase microextraction (SPME) fibers by sol-gel method and free radical cross-linking technology. The underlying mechanism of the sol-gel reaction was proposed and the successful chemical bonding of the crown ether functionalized IL to the formed hybrid organic-inorganic copolymer coating was confirmed by FT-IR spectroscopy. The performance of this in situ created crown ether functionalized IL-based SPME fibers, was investigated in detail. The coating has porous surface structure, stable performance in high temperature (to 340 °C) and in different solutions (water, organic solvent, acid and alkali), and good coating preparation reproducibility. In contrast to the sol-gel derived 1-allyl-3-methyl imidazolium hexafluorophosphate-based coating prepared in our previous work with the identical procedure, the extraction performance of this newly developed sol-gel crown ether functionalized IL-based coating was superior for alcohols, phthalate esters, phenolic environmental estrogens, fatty acids and aromatic amines due to the introduction of benzo-15-crown-5 functional group in IL structure. Moreover, it was shown to provide higher or comparable extraction efficiencies for most analytes studied than did the commercial PDMS, PDMS/DVB and PA fibers.     

Adsorption and conformational change of myoglobin on biomimetic hydroxyapatite nanocrystals functionalized with alendronate

The chemical conjugation of bisphosphonates (BPs), specifically alendronate, to hydroxyapatite could be an effective means to impart to it fine-tuned bioactivity. Horse heart myoglobin (Mb), a well-characterized protein, has been adsorbed onto biomimetic hydroxyapatite nanocrystals (nHA) and onto the nHA/alendronate conjugate powdered samples. The obtained materials have potential use in bone implantation and as prospective drug-delivery devices. The kinetic absorption of Mb onto nHA is dramatically affected by its functionalization with alendronate. The covering of the nHA surface by alendronate inhibits the adsorption of myoglobin. The adsorption mechanisms of the protein were studied by spectroscopic techniques (UV-vis and surface-enhanced Raman spectroscopy). The results indicate that the protein changes conformation upon adsorption on the inorganic substrate. In particular, the interaction with nHA alters the coordination state of the iron in the heme through the formation of a hexacoordinated low-spin Mb heme, possibly involving the distal histidine. Instead, the covering of the nHA surface by alendronate does not adsorb the protein but preserves the coordination state of the heme moiety. This study could be of significance either in the field of biomaterials science, in particular, to fine tune a bone-specific drug delivery device and to test nHA as a new support for heterogeneous catalysis, improving the understating of enzyme immobilization.     

Surface Heparinization of Poly(ether ether ketone)

Photo-grafting of hydrophilic monomer and space arms was used to enhance the hydrophilicity of poly(ether ether ketone)(PEEK) with the aim of extending its application to biological fields. PEEK films were surface modified by UV grafting of acrylic acid(AA) to introduce ―COOH on PEEK surface. Adipic amine was used as a space arm to introduce heparin on PEEK surface based on the condensation reaction between ―NH₂ and ―COOH. The modified PEEK(PEEK-COOH, PEEK-NH₂ and PEEK-Hep) was characterized by energy-disperse spectroscopy (EDS), X-ray photoelectron spectroscopy(XPS) and water contact angle measurements, which show that heparin was grafted on PEEK surface. The contact angles of modified PEEK films were lower than those of original films, demonstrating a significant improvement of surface hydrophilicity.     

Sulfonated poly(ether ether ketone) composite membranes based on amino-modified halloysite nanotubes that effectively immobilize phosphotungstic acid

In this work, we prepared amino-modified halloysite nanotubes (PEI-DHNTs) via the co-deposition of self-polymerized dopamine and polyethylenimine (PEI) on the surface of nanotubes, which was confirmed by X-ray photoelectron spectroscopy (XPS) and Thermogravimetric analysis (TGA). A series of composite proton exchange membranes (PEMs) were prepared by incorporating PEI-DHNTs and phosphotungstic acid (HPW) into sulfonated poly(ether ether ketone) (SPEEK). It was found that both PEI-DHNTs and HPW were well dispersed in the polymer matrix, exhibiting excellent filler-matrix compatibility. The composite membranes demonstrated enhanced proton conductivity, reaching as high as 0.078 S cm⁻¹ with 33.3 wt.% HPW loading, which was ~90% higher than that of SPEEK control membrane. Such improvement was mainly attributed to the strong acid–base pairs formed by PEI-DHNT with both SPEEK and HPW, which shortened proton hopping distance and created more continuous proton conduction pathways. Furthermore, the membrane conductivity remained almost constant after 1 year's immersion in liquid water, indicating the successful immobilization of HPW in the composite membranes.     

Incorporation of nanohydroxyapatite and vitamin D3 into electrospun PCL/Gelatin scaffolds: The influence on the physical and chemical properties and cell behavior for bone tissue engineering

Scaffold, an essential element of tissue engineering, should provide proper physical and chemical properties and evolve suitable cell behavior for tissue regeneration. Polycaprolactone/Gelatin (PCL/Gel)‐based nanocomposite scaffolds containing hydroxyapatite nanoparticles (nHA) and vitamin D3 (Vit D3) were fabricated using the electrospinning method. Structural and mechanical properties of the scaffold were determined by scanning electron microscopy (SEM) and tensile measurement. In this study, smooth and bead‐free morphology with a uniform fiber diameter and optimal porosity level with appropriate pore size was observed for PCL/Gel/nHA nanocomposite scaffold. The results indicated that adding nHA to PCL/Gel caused an increase of the mechanical properties of scaffold. In addition, chemical interactions between PCL, gelatin, and nHA molecules were shown with XRD and FT‐IR in the composite scaffolds. MG‐63 cell line has been cultured on the fabricated composite scaffolds; the results of viability and adhesion of cells on the scaffolds have been confirmed using MTT and SEM analysis methods. Here in this study, the culture of the osteoblast cells on the scaffolds showed that the addition of Vit D3 to PCL/Gel/nHA scaffold caused further attachment and proliferation of the cells. Moreover, DAPI staining results showed that the presence and viability of the cells were greater in PCL/Gel/nHA/Vit D3 scaffold than in PCL/Gel/nHA and PCL/Gel scaffolds. The results also approved increasing cell proliferation and alkaline phosphatase (ALP) activity for MG‐63 cells cultured on PCL/Gel/nHA/Vit D3 scaffold. The results indicated superior properties of hydroxyapatite nanoparticles and vitamin D3 incorporated in PCL/Gel scaffold for use in bone tissue engineering.