Mechanically alloyed nanocrystalline iron and copper mixture: behavior and constitutive modeling over a wide range of strain rates

A comprehensive study on the response of a nanocrystalline iron and copper mixture (80% Fe and 20% Cu) to quasi-static and dynamic loading is performed. The constitutive model developed earlier by Khan, Huang & Liang (KHL) is extended to include the responses of nanocrystalline metallic materials. The strain rate and grain size dependent behaviors of porous nanocrystalline iron-copper mixture were determined experimentally for both static and dynamic loading. A viscoplastic model is formulated by associating the modified KHL model (representing the fully dense matrix behavior), and Gurson's plastic potential which provides the yield criteria for porous material. Simulations of uniaxial compressive deformations of iron-copper mixture with different initial porosity, grain size and at a wide range of strain rate (10⁻⁴ to 10³ s⁻¹) are made. The numerical results correlate well with the experimental observations.     

Evolution of plastic zones in dynamically loaded plates using different elastic–viscoplastic laws

In the framework of viscoplastic theory many different laws were developed, accounting for material behaviors like creep, relaxation or evolution of overstresses. Though each model is able to predict in uni-axial material tests the values of stresses depending on plastic strains and plastic strain rates the question is if solutions of simulations are still realistic if the viscoplastic law is applied on structural deformations. In the present study strain rate sensitive metal plates are subjected to shock waves. The purpose is to compare simulation results obtained with different elastic–viscoplastic laws to experiments in order to determine the most appropriate material model. By subjecting circular metal plates experimentally to shock wave loadings realistic deformation histories are measured. The measurements are compared to simulation results obtained with different viscoplastic laws. The aim is to find out the accuracy of each model concerning the predictions of displacements, shape formings, spread of plastic zones and evolutions of inner bending moments.     

黏弹-Perzyna黏塑性有限元法应力更新隐式算法

黏弹-黏塑性耦合模型的黏弹性部分由弹簧、黏壶和Kelvin链串联而成,黏塑性部分为双曲线型DruckerPrager屈服函数、各向同性硬化和Perzyna黏塑性流动模型。基于黏弹性蠕变柔度,通过定义与弹性问题相对应的与时间增量相关的黏弹性剪切模量和体积模量,导出增量递推形式的本构方程。为保证算法的收敛和稳定性,把Perzyna黏塑性流动方程转化为与弹塑性相似的一致性条件,建立黏塑性增量因子单侧逼近其收敛值的N-R迭代算法。最后,给出应力更新完全隐式算法和最终计算公式。分别采用黏弹性、黏弹-塑性和黏弹-黏塑性本构关系对一地基蠕变模型进行三维有限元分析和比较,结果表明,本文算法具有较高的计算效率和稳定性。     

A viscoplastic constitutive model incorporating dynamic strain aging effect during cyclic deformation conditions

In this paper, a viscoplastic constitutive model previously proposed by the authors was extended to apply to the cyclic deformation analysis of the modified 9Cr-1Mo steel. A series of cyclic deformation tests were conducted on modified 9Cr-1Mo steel at various temperatures, including those under anisothermal conditions. Furthermore, cyclic evolution of state variables used in the authors' constitutive model was experimentally measured. Based on the test results, cyclic softening behavior depending on the temperature and its history was introduced into the constitutive model. The extended model was applied to simulations of inelastic deformation behavior under monotonic tension, stress relaxation, creep, isothermal cyclic deformations including stress relaxation and anisothermal cyclic deformations. It was found that the present constitutive model has a capability of describing the inelastic deformation behavior of modified 9Cr-1Mo steel adequately at various loading conditions.     

VISCOELASTIC CONSTITUTIVE MODEL RELATED TO DEFORMATION OF INSECT WING UNDER LOADING IN FLAPPING MOTION

Flexible insect wings deform passively under the periodic loading during napping flight. The wing flexibility is considered as one of the specific mechanisms on improving insect flight performance. The constitutive relation of the insect wing material plays a key role on the wing deformation, but has not been clearly understood yet. A viscoelastic constitutive relation model was established based on the stress relaxation experiment of a dragonfly wing (in vitro). This model was examined by the finite element analysis of the dynamic deformation response for a model insect wing under the action of the periodical inertial force in flapping. It is revealed that the viscoelastic constitutive relation is rational to characterize the biomaterial property of insect wings in contrast to the elastic one. The amplitude and form of the passive viscoelastic deformation of the wing is evidently dependent on the viscous parameters in the constitutive relation.     

A viscoelastic constitutive model of rubber under small oscillatory load superimposed on large static deformation

Summary  A viscoelastic constitutive equation of rubber that is under small oscillatory load superimposed on large static deformation is proposed. The model is derived through linearization of Simo's nonlinear viscoelastic constitutive model and reference configuration transformation. Most importantly, in this model, static deformation correction factor is introduced to consider the influence of pre-strain on the relaxation function. Natural statically pre-deformed state is served as reference configuration. The proposed constitutive equation is extended to a generalized viscoelastic constitutive equation that includes widely used Morman's model as a special case using objective stress increment. The proposed constitutive model is tested for dynamic behavior of rubber specimens with different carbon black content. It is concluded from the test that the assumption that the effects of static deformation can be separated from time effects, which is the basis of Morman's model, is only applicable to unfilled rubber. The viscoelastic constitutive equation for filled rubber must include, therefore, the influence of the static deformation on the time effects. The suggested constitutive equation with static deformation correction factor shows good agreement with test values. Received 4 January 2001; accepted for publication 13 June 2001     

Viscoelasticity and viscoplasticity of polypropylene/polyethylene blends

Observations are reported on polypropylene/polyethylene blends with various concentrations of components in uniaxial tensile tests with constant strain rates, relaxation tests, and creep tests at room temperature. A model is developed for the viscoelastic and viscoplastic responses of polymer blends at arbitrary three-dimensional deformation with small strains. Material constants in the constitutive equations are determined by fitting the experimental data. It is found that all adjustable parameters evolve with blend composition following an analog of the rule of mixture. Lifetime of blends under condition of creep rupture is evaluated by numerical simulation.     

Mechanical Performance of a Recycled Carbon Fibre/PP Composite

A composite made of recycled carbon fibres in recycled polypropylene matrix is studied experimentally to describe the features of the elastic and time dependent nonlinear mechanical behaviour. The properties of the developed material have a large variability to be addressed and understood. It was found that the stress-strain curves in tension are rather nonlinear at low strain rate and the strength is sensitive to strain rate. The elastic properties’ reduction for this composite after loading to high strains is rather limited. More important is that even in the “elastic region” due to viscoelastic effects the slope of loading–unloading curve is not the same and that at higher stress large viscoplastic strains develop and creep rupture is typical. The time and stress dependence of viscoplastic strains was analysed and described theoretically. The viscoelastic response of the composite was analysed using creep compliance, which was found to be slightly nonlinear.     

基于OTTOSEN准则的混凝土粘塑性力学模型

研究了混凝土的弹．粘塑性动态本构关系,提出一个应变率相关的非线性混凝土模型．模型改进Bicanic的混凝土塑性间断面变化规律和Ottosen的四参数屈服准则,建立冲击荷载下的混凝土本构方程,可以应用于地震和爆炸作用下混凝土材料响应的研究．根据混凝土动态实验结果对应变率和材料强度的关系提出合理假设,考虑以往被忽略的材料峰值应变和泊松比随应变率的变化．模型包含静水压力参数和动态塑性损伤因子,可以有效地反映混凝土的动态力学行为,为其动态问题的研究提供有益的思路和有效的工具．     

材料的弹粘塑性本构关系和应力波的演化

试验表明，大多数工程材料在冲击载荷作用之下的变形一般都同时包含有可恢复的瞬态性弹性变形和不可恢复的粘滞性塑性变形，即其本构关系可以用弹粘塑性模型来描述。本文从内变量理论出发，探讨了时率相关材料的弹粘塑性本构关系的一般特性，建立了增量型的弹粘塑性本构关系的一般理论框架和普适的表达式，并且对两种最常用的本构模型——Bodner-Partom模型和Johnson-Cook模型给出了在一维应变条件下的具体形式。通过计算和讨论一维应变粘塑性靶板中冲击波的衰减机制和应力波的演化规律，特别是考察各种粘塑性本构模型中的材料参数对冲击波的衰减和应力波的演化的影响，得出了一些可以直接应用或具有一定借鉴价值的结果，为研究应力波的其他衰减机制以及在人防工程中智能防护层设计时新材料的选取奠定了基础。     

Damage of ductile materials deforming under multiple plastic or viscoplastic mechanisms

This work presents a model to represent ductile failure (i.e. failure controlled by nucleation, growth and coalescence) of materials whose irreversible deformation is controlled by several plastic or viscoplastic deformation mechanisms. In addition work hardening may result from both isotropic and kinematic hardening. Damage is represented by a single variable representing void volume fraction. The model uses an additive decomposition of the plastic strain rate tensor. The model is developed based on the definition of damage dependant effective scalar stresses. The model is first developed within the generalized standard material framework and expressions for Helmholtz free energy, yield potential and dissipation potential are proposed. In absence of void nucleation, the evolution of the void volume fraction is governed by mass conservation and damage does not need to be represented by state variables. The model is extended to account for void nucleation. It is implemented in a finite element software to perform structural computations. The model is applied to three case studies: (i) failure by void growth and coalescence by internal necking (pipeline steel) where plastic flow is either governed by the Gurson–Tvergaard–Needleman model or the Thomason model, (ii) creep failure (Grade 91 creep resistant steel) where viscoplastic flow is controlled by dislocation creep or diffusional creep and (iii) ductile rupture after pre-compression (aluminum alloy) where kinematic hardening plays an important role.     

A MICROMECHANICAL FRAMEWORK WITH AGGREGATE-MASTIC INTERFACE EFFECT FOR PREDICTING UNIAXIAL COMPRESSION CREEP OF ASPHALT MIXTURE

According to the elastic-viscoelastic correspondence principle, an elastic microme- chanical framework taking the inclusion-matrix interface effect into account is extended for predicting viscoelastic properties of asphalt mixture, which is simply treated as elastic coarse aggregate inclusions periodically and isotropically embedded in a viscoelastic asphalt mastic matrix. The Burgers model is adopted for characterizing the matrix mechanical behavior, so that the homogenized relaxation modulus of asphalt mixture in compression creep is derived. After a series of uniaxial compression creep tests are performed on asphalt mastic in different temperature and stress conditions in order to determine the matrix constitutive parameters, the framework presented is validated by comparison with the experiment, and then some predictions of uniaxial compression creep behavior of asphalt mixture in different temperature and stress conditions are given.     

An Approach to Constructing a Rheological Model of a Strain-Hardening Medium

The one-dimensional constitutive equations of strain-hardening materials subject to nonlinear creep are derived. The solution is found using the hypothesis of unified deformation curve based on the similarity of the tensile and isochronic creep curves. A generalized rheological model is constructed which accounts for the instantaneous strain rate, loading rate, and the mode of strain hardening. This model is used to derive one-dimensional constitutive equations for linear viscoelastic, nonlinear viscoelastic, and linear- and nonlinear-hardening viscoelastoplastic materials. It is shown that the creep of linear viscoelastic and linear-hardening viscoelastoplastic materials is transient. For nonlinear viscoelastic and nonlinear-hardening viscoelastoplastic materials, all the characteristic stages of creep are present     

Aging, rejuvenation, and thixotropy in yielding magnetorheological fluids

The yielding behavior of dilute magnetorheological (MR) fluids has been investigated using creep–recovery tests. At very low stress levels, MR fluids behave in the linear viscoelastic regime as demonstrated by the fact that the instantaneous strain equals the instantaneous (elastic) recovery. In this region, gap-spanning field-induced structures support the stress levels applied. Upon increasing the stress value, the MR fluid evolves towards a nonlinear viscoelastic response. Here, the retarded elastic and viscous strain decrease, and the plastic contribution to the instantaneous strain grows probably due to the appearance of unattached field-induced structures. A larger stress value results in a viscoplastic solid behavior with negligible retarded and viscous strain and a fully plastic instantaneous strain. Finally, a plastic fluid behavior is found when the stress value is larger than the so-called yield stress. MR fluids exhibit an intermediate behavior between non-thixotropic (simple) and highly thixotropic model yield stress fluids.     

SnPb钎料合金的粘塑性Anand本构方程

采用统一型粘塑性本构 Anand方程描述了电子封装焊点 Sn Pb钎料合金的非弹性变形行为 ,基于 Sn Pb 合金的弹塑性蠕变本构方程和实验数据 ,确定了6 2 Sn36 Pb2 Ag、6 0 Sn40 Pb、96 .5 Sn3.5 Ag和 97.5 Pb2 .5 Sn四种钎料合金 Anand方程的材料参数 ,验证了粘塑性 Anand本构方程对 Sn Pb合金在恒应变速率和稳态塑性流动条件下应力应变行为的预测能力。结果表明 ,Anand方程能有效描述 Sn Pb钎料的粘塑性本构行为 ,并可应用于电子封装 Sn Pb焊点的可靠性模拟和失效分析     

丁基橡胶粘弹性材料的非线性蠕变本构描述

对丁基橡胶ZN-17粘弹性材料进行了不同温度、不同应力水平下的蠕变实验,揭示了该材料的非线性蠕变特性。基于蠕变实验结果,对标准线性固体模型描述该材料蠕变行为的预言能力进行了评估,提出了新的非线性蠕变本构模型。通过与实验结果比较,表明新模型能较好地描述该材料的非线性蠕变特性。     

基于西原模型的非线性黏弹塑性流变模型

在西原模型的基础上,引入能反映加速蠕变起始点的非线性黏塑性元件和瞬时塑性变形的塑性元件,建立了一个能完整反映蠕变全过程的非线性黏弹塑性流变模型. 在其一维流变模型结构的基础上建立三维的流变模型,推导三维流变方程,接着探讨了在三轴压缩试验中确定三维蠕变参数的方法,并对参数进行了敏感性分析. 用三轴压缩试验结果验证模型的有效性,结果表明模型能很好地模拟蠕变的三阶段,并且在多级偏应力水平下可以采用同一组蠕变参数.     

多孔硅橡胶有限变形的粘弹性行为

针对孔隙度较大（孔隙度大于50％）的硅橡胶材料在有限变形时的粘弹性行为，从建立描述材料粘弹性特征的松驰函数和变形特征的应变能函数出发，提出了适合多孔隙、可压硅橡胶材料的非线性粘弹性力学行为的本构关系，松驰函数和应变能函数可解耦为等容和体积变形两部分，并引入了拟时间的概念来反映变形对材料特征时间的影响，利用硅橡胶材料的单轴压缩松驰实验与材料模型进行了对比，讨论了多孔硅橡胶的等容变形和体积变形对应力松驰的影响。     

Experimental investigation of cyclic and time-dependent deformation of titanium alloy at elevated temperature

A novel cyclic deformation test program was undertaken to characterize macroscopic time dependent deformation of a titanium alloy for use in viscoplastic model development. All tests were conducted at a high homologous temperature, 650 °C, where there are large time dependent and loading rate dependent effects. Uninterrupted constant amplitude tests having zero mean stress or a tensile mean stress were conducted using three different control modes: strain amplitude and strain rate, stress amplitude and stress rate, and a hybrid stress amplitude and strain rate. Strain ratcheting occurred for all cyclic tests having a tensile mean stress and no plastic shakedown was observed. The shape of the strain ratcheting curve as a function of time is analogous to a creep curve having primary, steady state and tertiary regions, but the magnitude of the ratchet strains are higher than creep strains would be for a constant stress equal to the mean stress. Strain cycles interrupted with up to eight 2-h stress relaxation periods around the hysteresis loop, including hold times in each quadrant of the stress–strain diagram, were also conducted. Stress relaxation was path-dependent and in some cases the stress relaxed to zero. The cyclic behavior of these interrupted tests was similar even though each cycle was very complex. These results support constitutive model development by providing exploratory, characterization and validation data.