An investigation into the effects of unsteady parameters on the aerodynamics of a low Reynolds number pitching airfoil

The growing applications of low Reynolds number (LRN) operating vehicles impose the need for accurate LRN flow solutions. These applications usually involve complex unsteady phenomena, which depend on the kinematics of the vehicle such as pitching, plunging, and flapping of a wing. The objective of the present study is to address the issues related to LRN aerodynamics of a harmonically pitching NACA0012 airfoil. To this end, the influence of unsteady parameters, namely, amplitude of oscillation, d, reduced frequency, k, and Reynolds number, Re, on the aerodynamic performance of the model is investigated. Computational fluid dynamics (CFD) is utilized to solve Navier–Stokes (N–S) equations discretized based on the Finite Volume Method (FVM). The resulting instantaneous lift coefficients are compared with analytical data from Theodorsen’s method. The simulation results reveal that d, k, and Re are of great importance in the aerodynamic performance of the system, as they affect the maximum lift coefficients, hysteresis loops, strength, and number of the generated vortices within the harmonic motion, and the extent of the so-called figure-of-eight phenomenon region. Thus, achieving the optimum lift coefficients demands a careful selection of these parameters.     

Comparative Analysis of the Characteristics of the Vortex Wake behind a Flapping Wing Performing Oscillations of Different Types

The wake characteristics of a custom-designed airfoil performing pitching oscillations, heaving oscillations, and a combination of pitch and heave oscillations are compared in this study. The influence of flapping parameters are investigated at a constant Reynolds number Re\(_{c} = 2640\) and is presented for the Strouhal numbers based on the oscillation amplitude, St_A, varying in the \(0.1 \leqslant {\text{S}}{{{\text{t}}}_{A}} \leqslant 0.4\) range. The generation of vorticity above and below the airfoil depends on the airfoil’s initial direction of motion and remains the same for all types of flapping oscillations investigated. The evolution of the leading-edge and trailing-edge vortices is presented. The heaving oscillations of the airfoil are found to have a greater influence on the characteristics of the leading edge vortex. The wake behind the combined pitch-heave oscillations appears to be governed by pitching oscillations below \({\text{S}}{{{\text{t}}}_{A}} = 0.24\), whereas it is driven by heaving oscillations above \({\text{S}}{{{\text{t}}}_{A}} = 0.24\). The force computations indicate that the mere existence of the reverse von Kármán street is not sufficient to develop the thrust on the airfoil. The periodic component of velocity fluctuations significantly influences the wake characteristics. The anisotropic stress field developed around the airfoil due to the periodic fluctuations of the velocity is presented. The coherent structures developed in the wake are identified using the proper orthogonal decomposition and a qualitative comparison of the structures for different flapping oscillations is presented. The energy transfer from the flapping airfoil to the fluid for different flapping oscillations is highest for heaving oscillations followed by combined pitch-heave oscillations and pitching oscillations.

     

Correlation between vortex structures and unsteady loads for flapping motion in hover

During the past decade, efforts were made to develop a new generation of unmanned aircrafts, qualified as Micro-Air Vehicles. The particularity of these systems resides in their maximum dimension limited to 15 cm, which, in terms of aerodynamics, corresponds to low Reynolds number flows (Re ≈ 10² to 10⁴). At low Reynolds number, the concept of flapping wings seems to be an interesting alternative to the conventional fixed and rotary wings. Despite the fact that this concept may lead to enhanced lift forces and efficiency ratios, it allows hovering coupled with a low-noise generation. Previous studies (Dickinson et al. in Science 284:1954–1960, 1999) revealed that the flow engendered by flapping wings is highly vortical and unsteady, inducing significant temporal variations of the loads experienced by the airfoil. In order to enhance the aerodynamic performance of such flapping wings, it is essential to give further insight into the loads generating mechanisms by correlating the spatial and temporal evolution of the vortical structures together with the time-dependent lift and drag. In this paper, Time Resolved Particle Image Velocimetry is used as a basis to evaluate both unsteady forces and vortical structures generated by an airfoil undergoing complex motion (i.e. asymmetric flapping flight), through the momentum equation approach and a multidimensional wavelet-like vortex parameterization method, respectively. The momentum equation approach relies on the integration of flow variables inside and around a control volume surrounding the airfoil (Noca et al. in J Fluids Struct 11:345–350, 1997; Unal et al. in J Fluids Struct 11:965–971, 1997). Besides the direct link performed between the flow behavior and the force mechanisms, the load characterization is here non-intrusive and specifically convenient for flapping flight studies thanks to its low Reynolds flows’ sensitivity and adaptability to moving bodies. Results are supported by a vortex parameterization which evaluates the circulation of the multiple vortices generated in such complex flows. The temporal evolution of the loads matches the flow behavior and hence reveals the preponderant inertial force component and that due to vortical structures.     

High fidelity numerical simulation of airfoil thickness and kinematics effects on flapping airfoil propulsion

High-fidelity numerical simulations with the spectral difference (SD) method are carried out to investigate the unsteady flow over a series of oscillating NACA 4-digit airfoils. Airfoil thickness and kinematics effects on the flapping airfoil propulsion are highlighted. It is confirmed that the aerodynamic performance of airfoils with different thickness can be very different under the same kinematics. Distinct evolutionary patterns of vortical structures are analyzed to unveil the underlying flow physics behind the diverse flow phenomena associated with different airfoil thickness and kinematics and reveal the synthetic effects of airfoil thickness and kinematics on the propulsive performance. Thickness effects at various reduced frequencies and Strouhal numbers for the same chord length based Reynolds number (=1200) are then discussed in detail. It is found that at relatively small Strouhal number (=0.3), for all types of airfoils with the combined pitching and plunging motion (pitch angle 20°, the pitch axis located at one third of chord length from the leading edge, pitch leading plunge by 75°), low reduced frequency (=1) is conducive for both the thrust production and propulsive efficiency. Moreover, relatively thin airfoils (e.g. NACA0006) can generate larger thrust and maintain higher propulsive efficiency than thick airfoils (e.g. NACA0030). However, with the same kinematics but at relatively large Strouhal number (=0.45), it is found that airfoils with different thickness exhibit diverse trend on thrust production and propulsive efficiency, especially at large reduced frequency (=3.5). Results on effects of airfoil thickness based Reynolds numbers indicate that relative thin airfoils show superior propulsion performance in the tested Reynolds number range. The evolution of leading edge vortices and the interaction between the leading and trailing edge vortices play key roles in flapping airfoil propulsive performance.     

Modeling the flow past an oscillating airfoil by the method of viscous vortex domains

The Lagrangian vortex method for solving the Navier-Stokes equations is applied for numerically modeling the unsteady flow past a wing airfoil executing angular oscillations in a viscous incompressible flow. Formulas relating the unsteady forces on the airfoil and the vorticity field are derived. The calculated results are compared with the experimental data for the NACA-0012 airfoil executing harmonic oscillations in an air flow at the Reynolds number Re = 4.4 × 10⁴.     

Investigation of steady plasma actuation effect on aerodynamic coefficients of oscillating airfoil at low Reynolds number

In this work, numerical study of two dimensional laminar incompressible flow around an oscillating NACA0012 airfoil is proceeded using the open source code Open FOAM. Oscillatory motion types including pitching and flapping are considered. Reynolds number for these motions is assumed to be 12000 and effects of these motions and also different unsteady parameters such as amplitude and reduced frequency on aerodynamic coefficients are studied. For flow control on airfoil, dielectric barrier discharge plasma actuator is used in two different positions on airfoil and its effect is compared for the two types of considered oscillating motions. It is observed that in pitching motion, imposing plasma leads to an improvement in aerodynamic coefficients, but it does not have any positive effect on flapping motion.Also, for the amplitudes and frequencies investigated in this paper, the trailing edge plasma had a more desirable effect than other positions.     

Influence of heat transfer on the aerodynamic performance of a plunging and pitching NACA0012 airfoil at low Reynolds numbers

The unsteady low Reynolds number aerodynamics phenomena around flapping wings are addressed in several investigations. Elsewhere, airfoils at higher Mach numbers and Reynolds numbers have been treated quite comprehensively in the literature. It is duly noted that the influence of heat transfer phenomena on the aerodynamic performance of flapping wings configurations is not well studied. The objective of the present study is to investigate the effect of heat transfer upon the aerodynamic performance of a pitching and plunging NACA0012 airfoil in the low Reynolds number flow regime with particular emphasis upon the airfoil's lift and drag coefficients. The compressible Navier–Stokes equations are solved using a finite volume method. To consider the variation of fluid properties with temperature, the values of dynamic viscosity and thermal diffusivity are evaluated with Sutherland's formula and the Eucken model, respectively. Instantaneous and mean lift and drag coefficients are calculated for several temperature differences between the airfoil surface and freestream within the range 0–100 K. Simulations are performed for a prescribed airfoil motion schedule and flow parameters. It is learnt that the aerodynamic performance in terms of the lift C_L and drag C_D behavior is strongly dependent upon the heat transfer rate from the airfoil to the flow field. In the plunging case, the mean value of C_D tends to increase, whereas the amplitude of C_L tends to decrease with increasing temperature difference. In the pitching case, on the other hand, the mean value and the amplitude of both C_D and C_L decrease. A spectral analysis of C_D and C_L in the pitching case shows that the amplitudes of both C_D and C_L decrease with increasing surface temperature, whereas the harmonic frequencies are not affected.     

Effect of flexure on aerodynamic propulsive efficiency of flapping flexible airfoil

The aim of present study is to investigate the effect of chord-wise flexure amplitude on unsteady aerodynamic characteristics for a flapping airfoil with various combinations of Reynolds number and reduced frequency. Unsteady, viscous flows over a single flexible airfoil in plunge motion are computed using conformal hybrid meshes. The dynamic mesh technique is applied to illustrate the deformation modes of the flexible flapping airfoil. In order to investigate the influence of the flexure amplitude on the aerodynamic performance of the flapping airfoil, the present study considers eight different flexure amplitudes (a₀) ranging from 0 to 0.7 in intervals of 0.1 under conditions of Re=10⁴, reduced frequency k=2, and dimensionless plunge amplitude h₀=0.4. The computed unsteady flow fields clearly reveal the formation and evolution of a pair of leading edge vortices along the body of the flexible airfoil as it undergoes plunge motion. Thrust-indicative wake structures are generated when the flexure amplitude of the airfoil is less than 0.5 of the chord length. An enhancement in the propulsive efficiency is observed for a flapping airfoil with flexure amplitude of 0.3 of the chord length. This study also calculates the propulsive efficiency and thrust under various Reynolds numbers and reduced frequency conditions. The results indicate that the propulsive efficiency has a strong correlation with the reduced frequency. It is found that the flow conditions which yield the highest propulsive efficiency correspond to Strouhal number St of 0.255.     

Unsteady free surface wave-induced separation: Vortical structures and instabilities

Vortical structures and instability mechanisms of the unsteady free surface wave-induced separation around a surface-piercing NACA0024 foil at a Froude number of 0.37 and a Reynolds number of 1.52×10⁶ are studied using an unsteady Reynolds-averaged Navier–Stokes (URANS) code with a blended k?ε/k?ω turbulence model and a free surface tracking method. At the free surface, the separated flow reattaches to the foil surface resulting in a wall-bounded separation bubble. The mean and instantaneous flow topologies in the separation region are similar to the owl-face pattern. The initial shear-layer instability, the Karman-like instability, and the flapping instability are identified, and their scaling and physical mechanisms are studied. Validation with experimental fluid dynamics (EFD) and comparison with complementary detached-eddy simulation (DES) indicate that URANS resolves part of the organized oscillations due to the large-scale unsteady vortical structures and instabilities, thereby capturing the gross features of the unsteady separation. The URANS solutions show an initial amplitude defect of 30% for the free surface oscillations where the shear layer separates, and the defect progressively increases downstream as URANS rapidly dissipates the rolled up vortices.     

An experimental study of the effects of pitch-pivot-point location on the propulsion performance of a pitching airfoil

An experimental investigation was conducted to characterize the evolution of the unsteady vortex structures in the wake of a pitching airfoil with the pitch-pivot-point moving from 0.16C to 0.52C (C is the chord length of the airfoil). The experimental study was conducted in a low-speed wind tunnel with a symmetric NACA0012 airfoil model in pitching motion under different pitching kinematics (i.e., reduced frequency k=3.8–13.2). A high-resolution particle image velocimetry (PIV) system was used to conduct detailed flow field measurements to quantify the characteristics of the wake flow and the resultant propulsion performance of the pitching airfoil. Besides conducting “free-run” PIV measurements to determine the ensemble-averaged velocity distributions in the wake flow, “phase-locked” PIV measurements were also performed to elucidate further details about the behavior of the unsteady vortex structures. Both the vorticity–moment theorem and the integral momentum theorem were used to evaluate the effects of the pitch-pivot-point location on the propulsion performance of the pitching airfoil. It was found that the pitch-pivot-point would affect the evolution of the unsteady wake vortices and resultant propulsion performance of the pitching airfoil greatly. Moving the pitch-pivot-point of the pitching airfoil can be considered as adding a plunging motion to the original pitching motion. With the pitch-pivot-point moving forward (or backward), the added plunging motion would make the airfoil trailing edge moving in the same (or opposite) direction as of the original pitching motion, which resulted in the generated wake vortices and resultant thrust enhanced (or weakened) by the added plunging motion.     

Dynamic stall behavior from unsteady force measurements

A direct force measurement technique employing piezoelectric load cells is used to experimentally investigate a two-dimensional airfoil (NACA 0012) undergoing dynamic stall. The load cells are installed at each end of the airfoil and give the force response in two directions in the plane normal to the airfoil axis during oscillations. Experiments are carried out at a Reynolds number based on the airfoil chord equal to 7.7×10⁴, and at four reduced frequencies, k=0.005, 0.01, 0.02, and 0.04. Phase-averaged lift of the airfoil undergoing dynamic stall is presented. It is observed that hysteresis loops of the lift occur both when the airfoil is pitched to exceed its static stall limit and when it is still within its static stall limit, and they grow in size with increasing k at the same pitching mean angle of attack and pitching amplitude. Both the lift and the drag induced by the pitching motion are further analyzed using the methods of higher order correlation analysis and continuous wavelet transforms to undercover their nonlinear and nonstationary features, in addition to classical FFT-based spectral analysis. The results are quantitatively illustrated by an energy partition analysis. It is found that the unsteady lift and drag show opposite trends when the airfoil undergoes transition from the pre-stall regime to the full-stall regime. The degree of nonlinearity of the lift increases, and the lift show a nonstationary feature in the light-stall regime, while the nonlinearity of the drag decreases, and the drag shows nonstationary feature in both the light-stall and the full-stall regimes. Furthermore, the lift and the drag have significant nonlinear interactions as shown by the correlation analysis in the light-stall regime.     

Experimental study of pitching and plunging airfoils at low Reynolds numbers

Measurements of the unsteady flow structure and force time history of pitching and plunging SD7003 and flat plate airfoils at low Reynolds numbers are presented. The airfoils were pitched and plunged in the effective angle of attack range of 2.4°–13.6° (shallow-stall kinematics) and ?6° to 22° (deep-stall kinematics). The shallow-stall kinematics results for the SD7003 airfoil show attached flow and laminar-to-turbulent transition at low effective angle of attack during the down stroke motion, while the flat plate model exhibits leading edge separation. Strong Re-number effects were found for the SD7003 airfoil which produced approximately 25 % increase in the peak lift coefficient at Re = 10,000 compared to higher Re flows. The flat plate airfoil showed reduced Re effects due to leading edge separation at the sharper leading edge, and the measured peak lift coefficient was higher than that predicted by unsteady potential flow theory. The deep-stall kinematics resulted in leading edge separation that led to formation of a large leading edge vortex (LEV) and a small trailing edge vortex (TEV) for both airfoils. The measured peak lift coefficient was significantly higher (~50 %) than that for the shallow-stall kinematics. The effect of airfoil shape on lift force was greater than the Re effect. Turbulence statistics were measured as a function of phase using ensemble averages. The results show anisotropic turbulence for the LEV and isotropic turbulence for the TEV. Comparison of unsteady potential flow theory with the experimental data showed better agreement by using the quasi-steady approximation, or setting C(k) = 1 in Theodorsen theory, for leading edge–separated flows.     

Aerodynamics of laminar separation flutter at a transitional Reynolds number

Experimental observations of self-sustained pitch oscillations of a NACA 0012 airfoil at transitional Reynolds numbers were recently reported. The aeroelastic limit cycle oscillations, herein labelled as laminar separation flutter, occur in the range 5.0×10⁴≤Re_c≤1.3×10⁵. They are well behaved, have a small amplitude and oscillate about θ=0°. It has been speculated that laminar separation leading to the formation of a laminar separation bubble, occurring at these Reynolds numbers, plays an essential role in these oscillations. This paper focuses on the Re_c=7.7×10⁴ case, with the elastic axis located at 18.6% chord. Considering that the experimental rig acts as a dynamic balance, the aerodynamic moment is derived and is empirically modelled as a generalized Duffing–van-der-Pol nonlinearity. As expected, it behaves nonlinearly with pitch displacement and rate. It also indicates a dynamically unstable equilibrium point, i.e. negative aerodynamic damping. In addition, large eddy simulations of the flow around the airfoil undergoing prescribed simple harmonic motion, using the same amplitude and frequency as the aeroelastic oscillations, are performed. The comparison between the experiment and simulations is conclusive. Both approaches show that the work done by the airflow on the airfoil is positive and both have the same magnitude. The large eddy simulation (LES) computations indicate that at θ=0°, the pitching motion induces a lag in the separation point on both surfaces of the airfoil resulting in negative pitching moment when pitching down, and positive moment when pitching up, thus feeding the LCO.     

低雷诺数俯仰振荡翼型等离子体流动控制

针对低雷诺数翼型气动性能差的特点, 通过介质阻挡放电(dielectric barrier discharge, DBD)等离子体激励控制的方法, 提高翼型低雷诺数下的气动特性,改善其流场结构. 采用二维准直接数值模拟方法求解非定常不可压Navier-Stokes方程,对具有俯仰运动的NACA0012翼型的低雷诺数流动展开数值模拟.同时将介质阻挡放电激励对流动的作用以彻体力源项的形式加入Navier-Stokes方程,通过数值模拟探究稳态DBD等离子体激励对俯仰振荡NACA0012翼型气动特性和流场特性的影响.为了进行流动控制, 分别在上下表面的前缘和后缘处安装DBD等离子体激励器,并提出四种激励器的开环控制策略,通过对比研究了这些控制策略在不同雷诺数、不同减缩频率以及激励位置下的控制效果.通过流场结构和动态压强分析了等离子体进行流场控制的机理. 结果表明,前缘DBD控制中控制策略B(负攻角时开启上表面激励器,正攻角时开启下表面激励器)效果最好,后缘DBD控制中控制策略C(逆时针旋转时开启上表面激励器,顺时针旋转时开启下表面激励器)效果最好,前缘DBD控制效果会随着减缩频率的增大而下降, 同时会导致阻力增大.而后缘DBD控制可以减小压差阻力, 优于前缘DBD控制,对于计算的所有减缩频率(5.01~11.82)都有较好的增升减阻效果.在不同雷诺数下, DBD控制的增升效果较为稳定, 而减阻效果随着雷诺数的降低而变差,这是由流体黏性效应增强导致的.      

Numerical investigation of transonic flow over deformable airfoil with plunging motion

In this article, the transonic inviscid flow over a deformable airfoil with plunging motion is studied numerically. A finite volume method based on the Roe scheme developed in a generalized coordinate is used along with an arbitrary Lagrangian-Eulerian method and a dynamic mesh algorithm to track the instantaneous position of the airfoil.The effects of different governing parameters such as the phase angle, the deformation amplitude, the initial angle of attack, the flapping frequency, and the Mach number on the unsteady flow field and aerodynamic coefficients are investigated in detail. The results show that maneuverability of the airfoil under various flow conditions is improved by the deformation. In addition, as the oscillation frequency of the airfoil increases, its aerodynamic performance is significantly improved.     

等速上仰翼型动态失速现象研究

翼型大迎角绕流的静态失速将造成升力突降和气动性能急剧恶化，但利用非定常运动所产生 的动态失速效应，可以大大地延缓气流分离和失速现象的发生. 采用Rogers发 展的双时间步Roe格式，求解拟压缩性修正不可压N-S方程. 数值模拟了低雷诺数 ($Re=4.8 \times 10^{4}$)条件下NACA0015翼型作等速上仰($\alpha =0^{\circ} \sim 60^{\circ}$)的动态失速过程，同Walker的试验结果比 较，验证了计算结果的正确性. 研究了该过程中主涡、二次涡和三次涡的发展，升 力系数随攻角变化，以及不同上仰速度对动态失速效应所造成的影响.     

Wake visualization of a heaving and pitching foil in a soap film

Many fish depend primarily on their tail beat for propulsion. Such a tail is commonly modeled as a two-dimensional flapping foil. Here we demonstrate a novel experimental setup of such a foil that heaves and pitches in a soap film. The vortical flow field generated by the foil correlates with thickness variations in the soap film, which appear as interference fringes when the film is illuminated with a monochromatic light source (we used a high-frequency SOX lamp). These interference fringes are subsequently captured with high-speed video (500 Hz) and this allows us to study the unsteady vortical field of a flapping foil. The main advantage of our approach is that the flow fields are time and space resolved and can be obtained time-efficiently. The foil is driven by a flapping mechanism that is optimized for studying both fish swimming and insect flight inside and outside the behavioral envelope. The mechanism generates sinusoidal heave and pitch kinematics, pre-described by the non-dimensional heave amplitude (0–6), the pitch amplitude (0°–90°), the phase difference between pitch and heave (0°–360°), and the dimensionless wavelength of the foil (3–18). We obtained this wide range of wavelengths for a foil 4 mm long by minimizing the soap film speed (0.25 m s⁻¹) and maximizing the flapping frequency range (4–25 Hz). The Reynolds number of the foil is of order 1,000 throughout this range. The resulting setup enables an effective assessment of vortex wake topology as a function of flapping kinematics. The efficiency of the method is further improved by carefully eliminating background noise in the visualization (e.g., reflections of the mechanism). This is done by placing mirrors at an angle behind the translucent film such that the camera views the much more distant and out-of-focus reflections of the black laboratory wall. The resulting high-quality flow visualizations require minimal image processing for flow interpretation. Finally, we demonstrate the effectiveness of our setup by visualizing the vortex dynamics of the flapping foil as a function of pitch amplitude by assessing the symmetry of the vortical wake.     

Simulation of dynamic stall for a NACA 0012 airfoil using a vortex method

The unsteady, incompressible, viscous laminar flow over a NACA 0012 airfoil is simulated, and the effects of several parameters investigated. A vortex method is used to solve the two-dimensional Navier–Stokes equations in the vorticity/stream-function form. By applying an operator-splitting method, the “convection” and “diffusion” equations are solved sequentially at each time step. The convection equation is solved using the vortex-in-cell method, and the diffusion equation using a second-order ADI finite difference scheme. The airfoil profile is obtained by mapping a circle in the computational domain into the physical domain through a Joukowski transformation. The effects of several parameters are investigated, such as the reduced frequency, mean angle of attack, location of pitch axis, and the Reynolds number. It is observed that the reduced frequency has the most influence on the flow field.     

Assessment of 2D/3D numerical modeling for deep dynamic stall experiments

The results of computational fluid dynamics (CFD) simulations in two and three spatial dimensions are compared to pressure measurements and particle image velocimetry (PIV) flow surveys to assess the suitability of numerical models for the simulation of deep dynamic stall experiments carried out on a pitching NACA 23012 airfoil. A sinusoidal pitching motion with a 10° amplitude and a reduced frequency of 0.1 is imposed around two different mean angles of attack of 10° and 15°. The comparison of the airloads curves and of the pressure distribution over the airfoil surface shows that a three-dimensional numerical model can better reproduce the flow structures and the airfoil performance for the deep dynamic stall regime. Also, the vortical structures observed by PIV in the flow field are better captured by the three-dimensional model. This feature highlighted the relevance of three-dimensional effects on the flow field in deep dynamic stall.     

Investigation of the vortex induced unsteadiness of a separation bubble via time-resolved and scanning PIV measurements

A transitional separation bubble on the suction side of an SD7003 airfoil is considered. The transition process that forces the separated shear layer to reattach seems to be governed by Kelvin–Helmholtz instabilities. Large scale vortices are formed due to this mechanism at the downstream end of the bubble. These vortices possess a three-dimensional structure and detach from the recirculation region, while other vortices are formed within the bubble. This separation of the vortex is a highly unsteady process, which leads to a bubble flapping. The structure of these vortices and the flapping of the separation bubble due to these vortices are temporally and spatially analyzed at angles of attack from 4° to 8° and chord-length based Reynolds numbers Re _c = 20,000–60,000 using time-resolved PIV measurements in a 2D and a 3D set-up, i.e., stereo-scanning PIV measurements are done in the latter case. These measurements complete former studies at a Reynolds number of Re _c = 20,000. The results of the time-resolved PIV measurements in a single light-sheet show the influence of the angle of attack and the Reynolds number. The characteristic parameters of the separation bubble are analyzed focusing on the unsteadiness of the separation bubble, e.g., the varying size of the main recirculation region, which characterizes the bubble flapping, and the corresponding Strouhal number are investigated. Furthermore, the impact of the freestream turbulence is investigated by juxtaposing the current and former results. The stereo-scanning PIV measurements at Reynolds numbers up to 60,000 elucidate the three-dimensional character of the vortical structures, which evolve at the downstream end of the separation bubble. It is shown that the same typical structures are formed, e.g., the c-shape vortex and the screwdriver vortex at each Reynolds number and angle of attack investigated and the occurrence of these patterns in relation to Λ-structures is discussed. To evidence the impact of the freestream turbulence, these results are compared with findings of former measurements.