考虑热渗效应的有限热源固结近似解

通过建立考虑热渗效应和热流固耦合效应的饱和土体固结方程,研究了无限长圆柱热固结问题.利用Fourier和Laplace变换及其逆变换,给出了热固结问题的解析解;然后对空间内无限长圆柱形热源问题进行研究,得到非等温条件下柱体周围饱和土体温度、孔隙水压力的近似解,并总结其规律,分析了热渗系数、固结系数对温度作用下土体固结的影响.     

衰变热源作用下饱和多孔介质热固结问题的扩展精细积分法

热源作用下饱和多孔介质热固结效应是土木及能源工程领域的一个重要课题.由于问题的复杂性,已有的研究大多将介质假定为均匀各向同性,且将热源假定为恒定强度.实际工程中,天然饱和多孔介质常表现出明显的分层特性,热源强度也存在衰变性,为此本工作采用扩展精细积分法对衰变热源作用下层状饱和多孔介质的热固结问题进行研究.借助于积分变换,将饱和多孔介质热固结问题的偏微分方程转化为变换域内的常微分方程;然后对饱和多孔介质微层元进行合并消元,并结合边界条件,推导出衰变热源作用下层状饱和多孔介质热固结问题在积分变换域内的扩展精细积分解;对所得解答进行相应的数值积分逆变换,可获得所求温度、超静孔压及竖向位移在物理域内的解答.基于上述求解过程,编制相应的计算程序进行数值计算,通过与已有文献对比,验证本文扩展精细积分法在求解层状饱和多孔介质热固结问题中的适应性和正确性;最后通过几组算例,分析热源衰变周期、热源埋深及介质的成层性对热固结效应的影响.结果表明:热源衰变周期对温度和超静孔压的峰值、以及达到峰值的时间均有明显影响,衰变周期越长,二者峰值均越大,且达到峰值所需时间越长;热源埋深对超静孔压及竖向位移变化影响显著,深埋热源作用时热源两侧竖向位移呈对称分布,而浅埋热源两侧则无此现象;饱和多孔介质的分层特性对热固结效应影响明显.     

考虑热渗效应的有限长圆柱热固结解

在作者已建立的饱和多孔介质耦合非线性热弹性理论基础上,考虑热渗效应,建立了饱和多孔介质耦合热弹性固结方程,并推导了有限长圆柱热固结问题的解析解,进而以温控三轴试验的试样为例进行了算例分析,同时利用COMSOL软件进行了数值模拟,并将解析结果和数值结果进行对比．结果表明：在不排水条件下,影响试样最终孔压大小的参数是：土的泊松比>弹性模量>水的体膨胀系数,渗透系数对孔压变化影响不大,考虑与不考虑水土压缩性不影响孔压的计算;相对线弹性情况,考虑非线弹性膨胀系数随温度变化时的孔压有所下降,轴向应变变化很小．     

岩土介质非稳态热固结耦合问题的热源函数法

考虑耦合效应的饱和土体热固结问题控制方程,利用Fourier变换、Laplace变换给出其在变换域上的解,将初始温度场分布视为虚拟的热源或者将热源等价为特定的初始温度分布,利用热源函数法给出瞬时线热源非稳态温度场、应力场和位移场的解析求解方法,通过在时间域和空间域上进行积分,给出有初始温度场分布以及有分布内热源存在且热源强度随时间变化条件下的热固结问题计算方法。对一无限大物体内存在有平面矩形域热源情况下周围介质的温度、孔隙水压力以及位移等的变化特征进行分析。研究表明,热源函数法可有效地求解一系列复杂情况下的热固结问题。     

ANALYTICAL SOLUTION OF THERMAL CONSOLIDATION OF SATURATED SOILS WITH TWO PARALLEL CYLINDRICAL HEAT SOURCES1）

基于应力平衡条件、渗流连续方程、能量守恒方程,考虑土颗粒和孔隙水热膨胀系数的不同,建立考虑热水力耦合的饱和土体三维热固结控制方程。利用傅里叶变换和拉普拉斯变换导出变换域上的控制方程,解得点热源在变换域和实数域上的解析解,再利用区域积分给出两平行圆柱形热源热固结土体温度、孔压、位移的解析解,并对其进行分析,发现径距比增大会导致两热源温度相互影响程度减弱,热固结系数减小会导致孔压和位移的峰值增大。     

两平行圆柱热源作用下饱和土体热固结解析解

基于应力平衡条件、渗流连续方程、能量守恒方程,考虑土颗粒和孔隙水热膨胀系数的不同,建立考虑热水力耦合的饱和土体三维热固结控制方程。利用傅里叶变换和拉普拉斯变换导出变换域上的控制方程,解得点热源在变换域和实数域上的解析解,再利用区域积分给出两平行圆柱形热源热固结土体温度、孔压、位移的解析解,并对其进行分析,发现径距比增大会导致两热源温度相互影响程度减弱,热固结系数减小会导致孔压和位移的峰值增大。     

热局部非平衡下一维半无限长饱和多孔柱体的温度场分析

对于端部受温度载荷的一维半无限长多孔介质柱体,给出了热局部非平衡下固相和流相温度场在Laplace变换域中的解析表达式.对于冲击温度载荷的情况,获得了温度场在短时间内的Laplace逆变换渐近解析解.数值分析了流、固两相热扩散系数之比以及热交换系数对固相和流相温度场的影响,比较了热局部非平衡下加权温度与热局部平衡下温度之间的差别.     

存在定流量汇项的分数阶导数黏弹性饱和土体一维固结解析

采用半解析方法对外部荷载和内部汇项共同作用所诱发的分数阶导数黏弹性饱和土一维固结特性进行了研究。首先,将分数阶微积分理论引入Kelvin-Voigt黏弹性模型以表征饱和黏土的流变性;然后利用Laplace积分变换,解析求解了Laplace变换域内存在外部荷载和内部汇项的分数阶导数Kelvin-Voigt黏弹性饱和土体一维固结微分方程;并采用Crump数值解法实现Laplace数值逆变换,从而得到了物理空间一维固结问题的半解析解。将所得半解析解与经典弹性饱和土体一维固结的解析解及均布荷载(无内部汇项)所诱发的分数阶导数黏弹性饱和土一维固结的解析解进行了对比,验证了本文半解析解的有效性。最后开展了参数研究,讨论了分数阶导数阶次、固结系数和汇项强度对饱和黏土固结行为的影响。结果表明:分数阶导数阶次主要影响固结发展速率,分数阶导数阶次越大,饱和黏土达到固结稳定所需的时间越短;固结系数对存在内部汇项诱发的固结问题的影响与传统由荷载诱发的固结问题的影响不同。固结系数、汇项强度和汇项位置均主要影响饱和黏土的最终沉降量,固结系数越大,最终沉降量越小;汇项强度越大或汇项位置离透水边界越远,固结沉降量越大。且存在汇项后,双面排水条件下的最终沉降量小于单面排水条件下的最终沉降量。     

饱和多孔介质的热固结理论

本文严格地从混合物理论出发,详细地推导出了描述饱和多孔介质在热合固结耦合作用下性状的方程.作研究的混合物为温度单一和可混溶体,固液两相均为热弹性线性状态,且没有化学因索鑫与.本文的结果为研究热固结问题提供了理性基础和实用性方程.本文还对耦合效应、组分的可压缩性以及有效应力等概念进行了讨论,得出了一些有意义的结论.做为应用实例,本文还指出热固结问题的一般解法,并给出球对称加热情形的解析解答.     

无限长圆柱体中广义电磁热弹耦合问题研究

基于L-S广义热弹性理论,研究了处于磁场中无限长理想圆柱导体在边界受热冲击作用时的电磁热弹耦合问题.建立了广义电磁热弹耦合的有限元方程,为避免积分变换方法求解带来的精度丟失.采用将有限元方程直接在时间域求解的方法,得到了圆柱体中的温度、位移、应力、感应磁场和感应电场的分布规律,反映了热的波动性及电磁热弹的耦合效应.结果表明,将有限元方程直接在时间域求解,可以获得各物理量的准确分布.得到温度在热波波前处的阶跃,准确地反应热波的波动效应.     

A CONSOLIDATION MODEL OF GROUP WELLS ON COMPOSITE FOUNDATION1)

针对复合地基固结问题,考虑井阻和土体径竖向渗流的影响,建立 以"桩-土-桩"为单元的复合地基群井计算模型,采用解析解法,推导出瞬时载荷作用下复合地基群井固结解析解,讨论了复合地基固结特点和孔压等的变化规律。研究表明,复合地基群井固结模型为复合地基固结理论的研究提供了一种新思路,在井径比大于5 时,基于中心桩、边桩流量相等假设,复合地基群井固结理论所求固结度和传统固结理论所求固结度相差很小,可忽略不计;桩体渗透系数、内外扰动区土体径向渗透系数、土体竖向渗透系数越大,复合地基固结速率越快;堆载越大,最终达到稳定时的沉降量和竖向应变越大;地基表层土体的孔压消散速率和竖向应变速率大于地基深部土体。     

天津软土的次固结变形特性研究

关于软土地基主、次固结变形分析是一项既有理论价值又有实践意义的课题。通过对天津市海积软土进行的固结试验 ,从微观的角度出发 ,结合净势能曲线解释了固结曲线上拐点的意义 ,研究了次固结系数的变化规律 ,同时建立了次固结系数与时间、固结压力和压缩指数的关系。     

Heat transfer on a cylinder in accelerated slip flow

The axisymmetric laminar boundary layer flow along the entire length of a semi-infinite stationary cylinder under an accelerated free-stream is investigated. Considering flow at reduced dimensions, the boundary layer equations are developed with the conventional no-slip boundary condition for tangential velocity and temperature replaced by a linear slip-jump boundary condition. Asymptotic series solutions are obtained for the heat transfer coefficient in terms of the Nusselt number. These solutions correspond to prescribed values of the momentum and temperature slip coefficients and the index of acceleration. Heat transfer at both small and large axial distances is determined in the form of series solutions; whereas at intermediate distances, exact and interpolated numerical solutions are obtained. Using these results, the heat transfer along the entire cylinder wall is evaluated in terms of the parameters of acceleration and slip.     

Consolidation Statistics Investigation via Thin Layer Method Analysis

In this paper, the Thin Layer Method (TLM) is adapted for solving one-dimensional primary consolidation problems. It is also combined with a stochastic formulation integrating Monte Carlo simulations to investigate primary consolidation of a random heterogeneous soil profile. This latter is modeled as a set of superposed layers extending horizontally to infinity, and having random properties. Spatial variability of soil properties is considered in the vertical direction only. Soil properties of interest are elastic modulus and soil permeability, modeled herein as spatially random fields. Lognormal distribution is chosen because it is suitable for strictly non-negative random variables, and enables analyzing the large variability of such properties. The statistics regarding final settlement and its corresponding time are investigated by performing a parametric study, which integrates the influence of variation coefficient of both elastic modulus and soil permeability, and vertical correlation length. Obtained results indicate that heterogeneity significantly influences primary consolidation of the soil profile, generating a quite different way of soil grain rearrangement and water pressure dissipation in comparison to the homogeneous case, and causing a delay in the consolidation process.     

Rolling without Slip on a Transversely Isotropic Thermoelastic Half-space

Rolling without slip by a rigid cylinder on a transversely isotropic, coupled thermoelastic half-space at constant subcritical speed is studied. The cylinder is of infinite length, surface heat convection is neglected, and a dynamic steady state of plane strain is treated. The unmixed problem of traction applied to a translating surface strip is addressed first. A robust asymptotic form of the exact transform solution, valid when Fourier heat conduction dominates any thermal relaxation effect, is extracted, and inverted analytically. Use of material characterization and identification of parameters that vanish in the isotropic limit or are invariant under an isothermal–thermoelastic transformation result in compact full-field solutions. These expressions are used to construct analytical solutions that satisfy the mixed boundary value problem and auxiliary conditions of rolling contact. For the hexagonal material zinc, calculations are made for contact zone width and temperature increases near onset of zone yield. Mathematics Subject Classifications (2000) 73B30, 73C25, 73C30, 73C35.     

基于定常吹吸气的波浪型圆柱主动控制研究

基于定常吹吸气对波浪型圆柱近尾迹流动进行控制以增强柱体振动, 采用大涡模拟研究了亚临界雷诺数(Re = 3000)下前吹后吸和前后吸气控制方式在不同吹吸气工况对波浪型圆柱升阻力特性、时均压力系数、环量、湍动能及近尾迹流动结构的影响. 研究发现: 前吹后吸和前后吸气控制下波浪型圆柱在不同吹吸气动量系数工况脉动升力系数均显著提高, 最大较未受控直圆柱和波浪型圆柱分别提升高达636%和391%, 这主要可能归因于吹吸气控制使波浪型圆柱回流区变短, 高强度涡集中向钝体后方靠拢, 旋涡形成长度缩短, 展向涡流与顺流向涡流相互作用在波浪型圆柱下游形成的“肋状涡”变大变长, 近尾迹环量显著增大, 从而导致脉动升力系数增大, 这可能将诱导柱体产生更强的振动; 同时两种控制方式均改变了波浪型圆柱表面的压力分布, 由于在波浪型圆柱前驻点吹气使前端趋于流线型, 前吹后吸在不同吹吸气动量系数下波浪型圆柱的高压区减小, 但在后驻点吸气使得低压区增大, 而前后吸气在不同吹吸气动量系数下波浪型圆柱的高压区基本不变, 低压区增大. 研究结果可为低风速地区分布式风力俘能结构俘能效率提升提供基础理论支持.      

辽西风积土动应力试验研究

通过对辽西地区风积土动三轴试验, 研究了动荷载作用下辽西风积土的动强度特性和抗液化特性.通过控制不同的动荷幅值、固结比和固结围压等试验条件, 获得了抗震设防烈度为7 度时, 辽西风积土的动应力值和抗液化剪应力比. 利用Excel 软件, 对试验数据进行回归处理, 得到了该土试样的动应力与固结比和固结围压两种因素的经验关系式. 试验和回归分析结果表明, 风积土的动应力与固结比和固结围压成正比. 试验研究了不同固结比条件下辽西地区风积土的液化强度特性, 获得了不同固结比条件下的抗液化剪应力比. 试验结果表明, 风积土的抗液化剪应力随着固结比的增加而增大. 上述试验结果对于辽西地区工程的抗震设计具有重要的指导意义和工程实用价值.     

Forced Convection Heat Transfer from a Finite-Height Cylinder

This paper presents a large eddy simulation of forced convection heat transfer in the flow around a surface-mounted finite-height circular cylinder. The study was carried out for a cylinder with height-to-diameter ratio of 2.5, a Reynolds number based on the cylinder diameter of 44 000 and a Prandtl number of 1. Only the surface of the cylinder is heated while the bottom wall and the inflow are kept at a lower fixed temperature. The approach flow boundary layer had a thickness of about 10% of the cylinder height. Local and averaged heat transfer coefficients are presented. The heat transfer coefficient is strongly affected by the free-end of the cylinder. As a result of the flow over the top being downwashed behind the cylinder, a vortex-shedding process does not occur in the upper part, leading to a lower value of the local heat transfer coefficient in that region. In the lower region, vortex-shedding takes place leading to higher values of the local heat transfer coefficient. The circumferentially averaged heat transfer coefficient is 20 % higher near the ground than near the top of the cylinder. The spreading and dilution of the mean temperature field in the wake of the cylinder are also discussed.     

Uncoupled thermoelastic analysis for a thick cylinder with radiation

An attempt has been made to study the uncoupled thermoelastic response of thick cylinder of length 2h in which heat sources are generated according to the linear function of the temperature, with boundary conditions of the radiation type. This approach is based upon integral transform techniques, to find out the thermoelastic solution. The results are obtained in terms of Bessel functions in the form of infinite series.