Force and displacement transmissibility of a quasi-zero stiffness vibration isolator with geometric nonlinear damping

A geometric nonlinear damping is proposed and applied to a quasi-zero stiffness (QZS) vibration isolator with the purpose of improving the performance of low-frequency vibration isolation. The force, stiffness and damping characteristics of the system are presented first. The steady-state solutions of the QZS system are obtained based on the averaging method for both force and base excitations and further verified by numerical simulation. The force and displacement transmissibility of the QZS vibration isolator are then analysed. The results indicate that increasing the nonlinear damping can effectively suppress the force transmissibility in resonant region with the isolation performance in higher frequencies unaffected. In addition, the application of the nonlinear damping in the QZS vibration isolator can essentially eliminate the unbounded response for the base excitation. Finally, the equivalent damping ratio is defined and discussed from the viewpoint of vibration control.     

Influence of excitation amplitude on the characteristics of nonlinear butyl rubber isolators

The purpose of this study is to explore the advantages and characteristics of nonlinear butyl rubber (type IIR) isolators in vibratory shear by comparison with linear isolators. It is known that the mechanical properties of viscoelastic materials exhibit significant frequency and temperature dependence, and in some cases, nonlinear dynamic behavior as well. Nonlinear characteristics in shear deformation are reflected in mechanical properties such as stiffness and damping. Furthermore, even when the excitation amplitude is small the response amplitude may often be large enough that nonlinearities cannot be ignored. The treatment involves developing phenomenological models of the effective storage modulus and effective loss factor of a rubber isolator material as a function of excitation amplitude. The transmissibility of a nonlinear viscoelastic isolator is compared with that of a linear isolator using an equivalent linear damping coefficient. Forced resonance vibration and impedance tests are used to characterize nonlinear parameters and to measure the normalized transmissibility. It is found that as the excitation amplitude of the nonlinear viscoelastic isolator increases, the response amplitude decreases and the transmissibility is improved over that of the linear isolator for excitation frequency that exceeds a particular value governed by the temperature and excitation amplitude. The method of multiple scales and numerical simulations are used to predict the response characteristics of the isolator based on the phenomenological modeling under different values of system parameters.     

一种准零刚度系统隔振性能的几何参数优化分析

提出了一种采用菱形连杆组件作为负刚度机构的准零刚度隔振器(下文简称菱形准零刚度隔振器)。通过静力学分析方法,建立了菱形准零刚度隔振器数学模型,并与其他调节变量较少的隔振器模型进行了对比;以被测量曲线在隔振器平衡位置处的曲率作为评价参数,研究了负刚度机构几何参数对系统刚度、阻尼非线性的影响,推导了利用几何参数进行隔振优化的条件;采用谐波平衡法求解系统动力学方程,对隔振器在不同几何参数下的隔振性能进行了分析。结果表明:菱形准零刚度隔振器具有体积相对较小且非线性调节能力较好的特点,可通过调节杆长,或满足相关临界值条件时调节杆长偏差量(下文简称杆长差)对刚度及阻尼非线性特征进行优化;刚度与阻尼的非线性优化方向不同,但通常情况下,刚度非线性因素对隔振优化起主导作用;归一化振动相对位移小于0.1时,由刚度曲线曲率得到的临界值可以较好地作为杆长差参数的隔振优化调节依据。本文提出的非线性评价方法与几何非线性优化临界值计算方法,对于类似隔振器研究和设计具有一定的指导意义。     

带非线性弹簧的两自由度准零刚度隔振系统力传递率特性

基于多自由度系统中的反共振特性,分别在传统线性隔振系统的上、下两层引入非线性倾斜弹簧负刚度机构,构成两自由度准零刚度隔振器。通过静态特性分析,推导出系统满足零刚度条件时,各参数之间的关系,分析了力学参数及结构参数对系统刚度特性的影响。建立两自由度准零刚度隔振系统的非线性动力学方程,利用平均法求解,推导出力传递率表达式,结合数值分析方法,探讨系统在不同的上、下层隔振器阻尼比、竖直刚度比及质量比情况下的力传递率特性,并与单自由度准零刚度隔振系统及线性斜弹簧两自由度准零刚度隔振系统进行对比研究。结果表明：当结构参数 （即：倾斜弹簧处于静平衡位置的长度与倾斜弹簧原长的比值）较小且倾斜弹簧为软化弹簧时,可在平衡位置附近获得较小的系统刚度及较大的低刚度区间;通过选择适当的上、下层隔振器阻尼比、竖直刚度比与质量比,可减小系统的起始隔振频率,增宽隔振频带,加快系统力传递率在特定频段内的衰减速率,改善系统的低频隔振性能。     

An enhanced multi-term harmonic balance solution for nonlinear period-one dynamic motions in right-angle gear pairs

A nonlinear time-varying dynamic model for right-angle gear pair systems, considering both backlash and asymmetric mesh effects, is formulated. The mesh parameters that are characteristically time-varying and asymmetric include mesh stiffness, directional rotation radius and mesh damping. The period-one dynamic motions are obtained by solving the dimensionless equation of gear motion using an enhanced multi-term harmonic balance method (HBM) with a modified discrete Fourier Transform process and the numerical continuation method. The accuracy of the enhanced HBM solution is verified by comparison of its results to the more computational intensive, direct numerical integration calculations. Also, the Floquet theory is applied to determine the stability of the steady-state harmonic balance solutions. Finally, a set of parametric studies are performed to determine quantitatively the effects of the variation and asymmetry in mesh stiffness and directional rotation radius on the gear dynamic responses.     

Cascaded quasi-zero stiffness nonlinear low-frequency vibration isolator inspired by human spine

Human motion induced vibration has very low frequency, ranging from 2 Hz to 5 Hz. Traditional vibration isolators are not effective in low-frequency regions due to the trade-off between the low natural frequency and the high load capacity. In this paper, inspired by the human spine, we propose a novel bionic human spine inspired quasi-zero stiffness (QZS) vibration isolator which consists of a cascaded multi-stage negative stiffness structure. The force and stiffness characteristics are investigated first, the dynamic model is established by Newton’s second law, and the isolation performance is analyzed by the harmonic balance method (HBM). Numerical results show that the bionic isolator can obtain better low-frequency isolation performance by increasing the number of negative structure stages, and reducing the damping values and external force values can obtain better low-frequency isolation performance. In comparison with the linear structure and existing traditional QZS isolator, the bionic spine isolator has better vibration isolation performance in low-frequency regions. It paves the way for the design of bionic ultra-low-frequency isolators and shows potential in many engineering applications.

     

Vibration of two beams connected by nonlinear isolators: analytical and experimental study

To study the coupling vibration of nonlinear isolators and flexible bodies, test rigs of two flexible beams connected by wire mesh isolators are constructed and investigated both experimentally and analytically. A five-parameter polynomial model of wire mesh isolators is derived by identifying parameters in the frequency domain with the sine-sweep test. For obtaining the parameters that are valid in a wide range of frequency, a numerically assisted identification method is developed. With this model, the vibration of two flexible beams connected by wire mesh isolators is studied. The frequency response is obtained analytically by employing the Green’s function method and harmonic balance method. Sine-sweep test results with three test rigs show good coherence with the corresponding numerical results. With obtained experimental results and numerical results, effect of connection parameters is studied in detail. It is found that traditional design rules for isolators are no longer effective and the coupling vibration must be investigated in the design phase. Another phenomenon is that the damping has a function of weakening the effect of nonlinear stiffness. Nonlinear stiffness and nonlinear damping can decrease the transmissibility along with the increase of the excitation level.     

Effect of the system imperfections on the dynamic response of a high-static-low-dynamic stiffness vibration isolator

The dynamic response of a high-static-low-dynamic stiffness (HSLDS) isolator formed by parallelly connecting a negative stiffness corrector which uses compressed Euler beams to a linear isolator is investigated in this study. Considering stiffness and load imperfections, the resonance frequency and response of the proposed isolator are obtained by employing harmonic balance method. The HSLDS isolator with quasi-zero stiffness characteristics can offer the lowest resonance frequency provided that there is only stiffness or load imperfection. If load imperfection always exists, there is no need to make the stiffness to zero since it cannot provide the lowest resonance frequency any longer. The reason for this unusual phenomenon is given. The dynamic response will exhibit softening, hardening, and softening-to-hardening characteristics, depending on the combined effect of load imperfection, stiffness imperfection, and excitation amplitude. In general, load imperfection makes the response exhibit softening characteristic and increasing stiffness imperfection will weak this effect. Increasing the excitation level will make the isolator undergo complex switch between different stiffness characteristics.     

A quasi-zero-stiffness isolator with a shear-thinning viscous damper

Quasi-zero-stiffness(QZS) vibration isolators have been widely studied,because they show excellent high static and low dynamic stiffnesses and can effectively solve low-frequency and ultralow-frequency vibration. However, traditional QZS(T-QZS)vibration isolators usually adopt linear damping, owing to which achieving good isolation performance at both low and high frequencies is difficult. T-QZS isolators exhibit hardening stiffness characteristics, and their vibration isolation performance is e...     

含机械调频式动力吸振器的准零刚度隔振系统隔振性能分析

基于动力吸振器原理,在单自由度准零刚度隔振器基础上耦合可调频动力吸振器构成两自由度隔振系统。首先,对动力吸振器工作原理进行理论分析并提出其力学模型;其次,通过静力学分析,推导出系统满足零刚度条件时,各参数间的关系并分析其对系统刚度特性的影响;然后,建立两自由度隔振系统非线性动力学方程,利用谐波平衡法进行幅频响应解析分析,得到力传递率表达式;最后,数值分析动力吸振器阻尼、刚度、质量、激励力幅值和弹簧片有效长度对力传递率的影响规律,并与单自由度准零刚度隔振系统及两自由度线性隔振系统对比分析。结果表明：通过选择适当的动力吸振器参数不仅可以减小系统的起始隔振频率,增宽隔振频带,且还能加快系统力传递率在特定频段内的衰减速率,改善系统的低频隔振性能,实现激励频率的可适应性。     

Nonlinear dynamics of a spur gear pair with force-dependent mesh stiffness

Time-varying mesh stiffness is one of the main excitation sources of a gear system, and it is also considered as an important factor for the vibration and noise of gears. Thus, this excitation is usually taken as an input into the gear dynamic model to obtain the system dynamic responses. However, the mesh stiffness of a gear pair is actually nonlinear with respect to the dynamic mesh force (DMF) that fluctuates during the operation of gears. Therefore, the dynamic model of gears with the quasi-static mesh stiffness calculated under a constant load is not accurate sufficiently. In this paper, a dynamic model of spur gear is established with considering the effect of the force-dependent time-varying mesh stiffness, backlash and profile deviation. Due to the nonlinear relationship between the mesh stiffness and the load for each tooth pair, it needs first to determine the load sharing among tooth pairs and then calculate the overall mesh stiffness of the gear pair. As the mesh stiffness and DMF are related, the mesh stiffness is no longer directly taken into the gear dynamic model as an input, but is jointly solved with the numerical integration process using the gear dynamic model. Finally, the dynamic responses predicted from the established gear dynamic model are compared with the experimental results for validation and compared with the traditional models to reveal their differences. The results indicate that the established dynamic model of spur gear transmission has a wider application range than the traditional models.     

A high-static–low-dynamic-stiffness vibration isolator with the auxiliary system

High-static–low-dynamic-stiffness (HSLDS) vibration isolators seek to widen the frequency range of isolation by decreasing the dynamic stiffness so as to reduce the natural frequency, while maintaining the same static displacement as equivalent linear isolators. However, in many cases especially under light damping or large excitations, the peak transmissibility is very large and the hardening nonlinearity causes the transmissibility curve to bend to the right seriously or in other words causes the jump phenomenon, resulting in a greatly reduced isolation region. In this paper, an auxiliary system is added to the HSLDS isolator to overcome these disadvantages, with the static displacement of the isolation object remaining unchanged. Coefficient-varying harmonic balance method is proposed in this paper to find the dynamic response and most importantly analyze the stability of the steady-state response. The isolation performance of the HSLDS-AS isolator, which is evaluated by displacement transmissibility, is compared with that of the equivalent HSLDS isolator. The effects of system parameters on the isolation performance are investigated. It is shown that the auxiliary system can lower the peak transmissibility and eliminate the jump phenomenon, resulting in a wide isolation region, and the HSLDS-AS isolator has strong designability with many parameters tunable.     

Bifurcation and chaos analysis of multistage planetary gear train

A nonlinear time-varying dynamic model for a multistage planetary gear train, considering time-varying meshing stiffness, nonlinear error excitation, and piece-wise backlash nonlinearities, is formulated. Varying dynamic motions are obtained by solving the dimensionless equations of motion in general coordinates by using the varying-step Gill numerical integration method. The influences of damping coefficient, excitation frequency, and backlash on bifurcation and chaos properties of the system are analyzed through dynamic bifurcation diagram, time history, phase trajectory, Poincaré map, and power spectrum. It shows that the multi-stage planetary gear train system has various inner nonlinear dynamic behaviors because of the coupling of gear backlash and time-varying meshing stiffness. As the damping coefficient increases, the dynamic behavior of the system transits to an increasingly stable periodic motion, which demonstrates that a higher damping coefficient can suppress a nonperiodic motion and thereby improve its dynamic response. The motion state of the system changes into chaos in different ways of period doubling bifurcation, and Hopf bifurcation.     

磁致伸缩主被动隔振装置中的磁机耦合效应研究

磁致伸缩材料和柔顺位移放大机构组成的主动驱动装置具有精度高、驱动力大等特点.将其与被动隔振装置并联,形成主被动隔振装置,可以弥补纯被动隔振在低频和微幅扰动工况下的不足.本文针对这类磁致伸缩主被动隔振装置进行磁机耦合效应研究.基于Jiles-Atherton模型,分析了磁致伸缩材料所受应力对有效磁场、磁化强度、磁致伸缩系数和材料杨氏模量的影响,表征了材料磁机耦合效应.在此基础上,建立了主被动隔振装置的动力学模型,分析了主动驱动装置与被动隔振装置间的耦合作用.在耦合作用影响下,若被动隔振装置刚度不同,即使输入磁场相同,驱动器产生的驱动位移和驱动力也不相同.磁致伸缩材料的变刚度效应使隔振装置整体等效刚度不再为定值,从而影响被动隔振效果.本文提出了通过柔顺机构参数设计减小前述两种耦合影响的方法.数值仿真结果表明,磁致伸缩主被动隔振装置在低于、接近和高于谐振频率三类扰动下,都能达到比被动隔振更好的振动抑制效果.此外,仿真结果验证了考虑磁机耦合效应的数值模型具有更高精度.      

DYNAMIC CHARACTERISTICS OF VIBRATION ISOLATION SYSTEM WITH CUBIC STIFFNESS AND HYSTERESIS 1)

包含立方刚度和Bouc-Wen 型滞回的隔振系统具有复杂的非线性动力学特性。系统无阻尼响应模型可基于无滞回恢复力建立,利用谐波平衡法和泰勒展开求得近似解析解。系统有阻尼响应模型可利用解析/数值联合方法求解,该方法基于谐波平衡法和Levenberg-Marquardt 迭代算法,对于滞回产生的多值非光滑函数项,先计算时域响应再通过快速傅里叶变换求解谐波项系数。上述方法在含水平绞制梁的非线性隔振系统分析中得到有效应用。分析表明,在Bouc-Wen 型滞回和立方刚度的综合影响下,隔振系统呈现渐软–渐硬特性,滞回阻尼和线性阻尼都可以有效抑制共振,但前者高频隔振效果优于后者。     

Bifurcation of multi-freedom gear system with spalling defect

This study focuses on the bifurcation characteristics of the four degree-of-freedom gear system with local spalling defect to explore the spalling nonlinear dynamic mechanism. The dynamic model of the gear system with spalling defect, time-variant mesh stiffness, and nonlinear clearance is established to investigate the effect of spalling defect on mesh stiffness and dynamic bifurcation. The primary resonance and internal resonance responses of the spalling model are analyzed by the averaging method, and the bifurcation characteristics with the evolvement of spall and internal excitation are studied by employing the singularity theory for the two-state variable system, which reveal the different bifurcation characteristics caused by the spalling defect. The results obtained herein can provide a theoretical basis to spalling fault diagnosis of gearbox.     

多尺度法的推广及在非线性黏弹性系统的应用

黏弹性材料在航空、机械、土木等领域具有广阔的应用前景,而具有1.5自由度的非线性Zener模型能更好地描述其特性.因此,研究多尺度法的推广和应用具有重要意义.在传统多尺度法的基础上,推广并利用多尺度法对非线性奇数阶微分方程进行研究,解决非线性奇数阶系统的动力学求解问题.以非线性Zener模型为例,首先通过推广的多尺度法...     

被动隔振体非线性振动的能量迭代解法

研究了由基础振动激励、弹性材料隔离的被动隔振体的强非线性动力响应。用变形的三次多项式函数表征隔振材料的非线性刚度特性,建立了被动隔振体的非线性动力学方程,得到有阻尼受迫振动Duffing方程。将求解强非线性自治系统的能量迭代方法加以改进,推广应用到强非线性非自治系统,求出周期响应的近似解析解表达式,以及幅频关系、相频关系和隔振系数的近似表达式。算例中应用本方法与Runge-Kutta方法进行了对照,结果表明求解精度较高。本文利用计算机进行了辅助推导。     

Enhanced isolation performance of a high-static–low-dynamic stiffness isolator with geometric nonlinear damping

Nonlinear Dynamics - To enhance the low-frequency vibration isolation performance of the high-static–low-dynamic stiffness (HSLDS) isolator, a novel design of the geometric nonlinear damping...     

The X-structure/mechanism approach to beneficial nonlinear design in engineering

Nonlinearity can take an important and critical role in engineering systems, and thus cannot be simply ignored in structural design, dynamic response analysis, and parameter selection. A key issue is how to analyze and design potential nonlinearities introduced to or inherent in a system under study. This is a must-do task in many practical applications involving vibration control, energy harvesting, sensor systems, robotic technology, etc. This paper presents an up-to-date review on a cutting-edge method for nonlinearity manipulation and employment developed in recent several years, named as the X-structure/mechanism approach. The method is inspired from animal leg/limb skeletons, and can provide passive low-cost high-efficiency adjustable and beneficial nonlinear stiffness (high static & ultra-low dynamic), nonlinear damping (dependent on resonant frequency and/or relative vibration displacement), and nonlinear inertia (low static & high dynamic) individually or simultaneously. The X-structure/mechanism is a generic and basic structure/mechanism, representing a class of structures/mechanisms which can achieve beneficial geometric nonlinearity during structural deflection or mechanism motion, can be flexibly realized through commonly-used mechanical components, and have many different forms (with a basic unit taking a shape like X/K/Z/S/V, quadrilateral, diamond, polygon, etc.). Importantly, all variant structures/mechanisms may share similar geometric nonlinearities and thus exhibit similar nonlinear stiffness/damping properties in vibration. Moreover, they are generally flexible in design and easy to implement. This paper systematically reviews the research background, motivation, essential bio-inspired ideas, advantages of this novel method, the beneficial nonlinear properties in stiffness, damping, and inertia, and the potential applications, and ends with some remarks and conclusions.