非线性压电效应下压电层合板的弯曲

考虑非线性压电效应,即电致弹性和电致伸缩效应情况下压电层合板的弯曲。从非线性压电方程和几何方程导出了压电层合板合应力、合力矩与应变之间的广义本构关系,这些关系关于电场是非线性的。利用Ritz法和双傅立叶级数得到四边简支对称压电层合板在高电场作用下的非线性解并进行计算。结果表明,只考虑线性压电效应只能适应于作用电场较低或基础层的刚度比压电层的刚度要大得多的情况。     

Nonlinear vibration of viscoelastic laminated composite plates

The dynamic behavior of laminated composite plates undergoing moderately large deflection is investigated by considering the viscoelastic properties of the material. Based on von Karman's nonlinear deformation theory and Boltzmann's superposition principle, nonlinear and hereditary type governing equations are derived through Hamilton's principle. Finite element analysis and the method of multiple scales are applied to examine the effect of large amplitude on the dissipative nature as well as on the natural frequency of viscoelastic laminated plates. Numerical experiments are performed for the nonlinear elastic case and linear viscoelastic case to check the validity of the procedure presented in this paper. Limitations of the method are discussed also. It is shown that the geometric nonlinearity does not affect the dissipative characteristics in the cases that have nonlinearity of perturbed order.     

Creep buckling and post-buckling analysis of the laminated piezoelectric viscoelastic functionally graded plates

The creep buckling and post-buckling of the laminated piezoelectric viscoelastic functionally graded material (FGM) plates are studied in this research. Considering the transverse shear deformation and geometric nonlinearity, the Von Karman geometric relation of the laminated piezoelectric viscoelastic FGM plates with initial deflection is established. And then nonlinear creep governing equations of the laminated piezoelectric viscoelastic FGM plates subjected to an in-plane compressive load are derived on the basis of the elastic piezoelectric theory and Boltzmann superposition principle. Applying the finite difference method and the Newmark scheme, the whole problem is solved by the iterative method. In numerical examples, the effects of geometric nonlinearity, transverse shear deformation, the applied electric load, the volume fraction and the geometric parameters on the creep buckling and post-buckling of laminated piezoelectric viscoelastic FGM plates with initial deflection are investigated.     

Iterative method for large deflection nonlinear problem of laminated composite shallow shells and plates

ＩｎｔｒｏｄｕｃｔｉｏｎＡｓｃｏｍｐｏｓｉｔｅｓａｒｅｅｘｔｅｎｓｉｖｅｌｙａｐｐｌｉｅｄｉｎｍｏｄｅｒｎｅｎｇｉｎｅｒｉｎｇｓｔｒｕｃｔｕｒｅｓａｎｄｍｅｃｈａｎｉｃｓｏｆｃｏｍｐｌｅｘｍａｔｅｒｉａｌｓｈａｓｂｅｎｈｉｇｈｌｙａｄｖａｎｃｅｄ,ｉ...     

Note on the Postbuckling Analysis of Cross-Ply Laminated Plates with Elastically Restrained Edges and Initial Curvatures

An approximate solution is presented for the postbuckling problem of cross-ply laminated plates having elastically restrained edges and initial imperfections. By the method of Bubnov-Galerkin the governing nonlinear differential equations are reduced to a system of simultaneous nonlinear ordinary algebraic equations depicting nonlinearity between applied loads and plate lateral deflections. As a numerical example, the case of a square plate made of different materials e.g., isotropic, glass fiber reinforced plastic, and carbon fiber reinforced plastic, under the effect of an initial central deflection and having different edge restraints has been studied.     

Analytical solution for the cylindrical bending vibration of piezoelectric composite plates

An analytical solution for the cylindrical bending vibrations of linear piezoelectric laminated plates is obtained by extending the Stroh formalism to the generalized plane strain vibrations of piezoelectric materials. The laminated plate consists of homogeneous elastic or piezoelectric laminae of arbitrary thickness and width. Fourier basis functions for the mechanical displacements and electric potential that identically satisfy the equations of motion and the charge equation of electrostatics are used to solve boundary value problems via the superposition principle. The coefficients in the infinite series solution are determined from the boundary conditions at the edges and continuity conditions at the interfaces between laminae, which are satisfied in the sense of Fourier series. The formulation admits different boundary conditions at the edges of the laminated piezoelectric composite plate. Results for laminated elastic plates with either distributed or segmented piezoelectric actuators are presented for different sets of boundary conditions at the edges.     

Nonlinear dynamic response of piezoelastic laminated plates considering interfacial damage effects

This paper presents a nonlinear model for cross-ply piezoelastic laminated plates containing the damage effect of the intralayer materials and interlaminar interfaces. The model is based on the general six-degrees-of-freedom plate theory, the discontinuity of displacement, and electric potential on the interfaces are depicted by three shape functions, which are formulated according to solutions about three equilibrium equations and conservation of charge. By using the Hamilton variation principle, the three-dimensional nonlinear dynamic equations of piezoelastic laminated plates with damage are presented. Then using the finite difference method and the Newmark scheme, an analytical solution is presented. In numerical examples, the effects of different damage models, damage evolution, amplitude and frequency of electric loads on the nonlinear dynamic response of piezoelectric laminated plate with interfacial imperfections are investigated.     

复合材料层合板的二次屈曲和二次分枝点分析

为了研究复合材料层合板的二次分叉特性 ,利用能量变分原理和非线性几何方程建立了具有弹性约束的复合材料层合板在面内载荷作用下的非线性稳定性控制方程组。控制方程组用广义傅立叶级数法进行求解 ,并得到载荷 -挠度曲线。基于分叉理论中的 Lerray-Schaulder定理 ,采用小挠动法 ,直接导出了复合材料层合板的二次失稳方程。研究结果表明 ,非对称层板也可能存在分叉 ,弹性转动支持系数和铺层等因素对二次分叉有很重要的影响。随着弹性系数的增大 ,二次失稳载荷值与初次失稳载荷值之比下降     

On kinematic coupling equations within the scaled boundary finite-element method

The scaled boundary finite element method is a semi-analytical analysis technique, which combines the advantages of the finite element method and the boundary-element method. Assuming that the geometry of the governing structure can be represented by mapping its boundary with respect to the so-called scaling coordinate, the problem can be handled in a closed-form analytical manner in the scaling direction and by a finite-element approximation in the other directions. Thus, a discretization of the boundary is sufficient and the nodal degrees of freedom are functions of the scaling coordinate. In some situations, such as the analysis of the free-edge effect in laminated plates, it is useful to introduce kinematic coupling equations, which are valid not only on the boundary, but also within the domain. The implementation of linear kinematic coupling equations within the method is presented for the case of a three-dimensional structure with scaling in a fixed Cartesian direction. Rigid-body modes are handled by using the concept of generalized inverse matrices. In some benchmark examples the efficiency of the approach is demonstrated and comparison with the results of the finite-element method shows good accordance.     

具损伤压电智能层合中厚板的非线性动力稳定性分析

基于各向异性损伤理论和压电理论，采用能量法和Lagrange方程，建立了具损伤压电智能层合中厚板在参数激励下的非线性运动控制方程，应用增量谐波平衡法，求解了具损伤压电智能层合中厚板的非线性动力稳定性问题。算例中，分析了损伤参数和压电效应对压电智能层合板非线性动力稳定性的影响，揭示了力电耦合效应的内在特征，并与有关文献的结果进行了比较。     

高阶剪切变形理论下三边夹紧一边铰支复合材料层板的几何非线性分析

首先用虚位移原理推导出以位移形式表达的Reddy型高阶剪变形理论复合材料层板的非线性控制方程及相应的边界条件。选定的五个位移函数均满足三边夹紧一边铰支边界条件，用Galerkin方法把无量纲化之后的控制方程转化为一组非线性代数方程组，用线性化的方法和可调节参数的修正迭代法求解这组方程。最后求出了不同复合材料的挠度和弯矩值。     

黏弹性环形板的临界载荷及动力稳定性

利用线性黏弹性力学的Boltzmann叠加原理,在考察位移单值性条件的基础上,给出黏弹性环形板非线性动力学分析的初边值问题。通过Galerkin方法和引进新的状态变量,将其化归为四维非线性非自治常微分方程组,从而得到黏弹性环形板的四种临界载荷,同时考察了几何缺陷对黏弹性薄板临界载荷的影响。根据Floquet理论,得出黏弹性形板在周期激励下的线性动力稳定性判据。综合使用非线性动力学中的数值分析方法,研究了参数对黏弹性环形板非线性动力稳定性的影响。     

Analysis of interlaminar stress and nonlinear dynamic response for composite laminated plates with interfacial damage

By considering the effect of interfacial damage and using the variation principle, three-dimensional nonlinear dynamic governing equations of the laminated plates with interfacial damage are derived based on the general sixdegrees-of-freedom plate theory towards the accurate stress analysis. The solutions of interlaminar stress and nonlinear dynamic response for a simply supported laminated plate with interfacial damage are obtained by using the finite difference method, and the results are validated by comparison with the solution of nonlinear finite element method. In numerical calculations, the effects of interfacial damage on the stress in the interface and the nonlinear dynamic response of laminated plates are discussed.     

考虑几何与压电非线性行为压电层合轴对称圆板的精确解

研究可移简支及夹支边界条件下,轴对称压电层合圆板在强电场和机械荷载联合作用下的非线性变形.考虑电致伸缩的非线性压电效应及几何非线性的影响,导出轴对称压电层合圆板的控制方程.通过调整坐标轴的位置对控制方程进行简化,得到关于挠度和径向力的4阶非线性控制方程.再通过简单的积分并引入无量刚变量将控制方程等价地化为2阶非线性耦合微分方程组.利用幂级数法得到可移简支及夹支边界条件下强电场和均布荷载共同作用时的挠度、径向力及径向位移的幂级数精确解.通过对双、单压电晶片执行器的数值计算及分析,得到电场、外载对于位移、径向力的影响关系.     

Large deflections of heterogeneous anisotropic rectangular plates

An approximate solution is presented for large deflections of clamped, uniformly loaded, unsymmetrically laminated, anisotropic, rectangular plates. Expressing the load and displacements in the form of series, the von Karman-type nonlinear differential equations and immovable boundary conditions are reduced to a series of linear partial differential equations and boundary conditions. The solution obtained by successive approximations can reduce to some existing solutions for large deflections of homogeneous plates. Numerical results based on the first three terms of the truncated series are graphically presented for unsymmetrical cross-ply and angle-ply plates having various values of fiber-reinforced material, number of layers, and aspect ratio. The results in small deflections of coupled laminates are compared with available data.     

Higher Order Convergence Rates in Theory of Homogenization: Equations of Non-divergence Form

We establish higher order convergence rates in the theory of periodic homogenization of both linear and fully nonlinear uniformly elliptic equations of non-divergence form. The rates are achieved by involving higher order correctors which fix the errors occurring both in the interior and on the boundary layer of our physical domain. The proof is based on a viscosity method and a new regularity theory which captures the stability of the correctors with respect to the shape of our limit profile.     

Biharmonic Problem in a Rectangle

This paper addresses the fascinating long history of the classical two-dimensional biharmonic problem for a rectangular domain. Among various mathematical and engineering approaches, the method of superposition is effective for solving mechanical problems concerning creeping flow of viscous fluid set up in a rectangular cavity by tangential velocities applied along its walls, an equilibrium of an elastic rectangle, and bending of a clamped thin rectangular elastic plate by a normal load. The object of this paper is both to clarify some purely mathematical questions connected with the solution of the infinite systems of linear algebraic equations and to provide a considerable simplification of the numerical algorithm. The method is illustrated by several examples of steady Stokes flow in a square cavity.     

Nonlinear bending of simply supported symmetric laminated cross-ply rectangular plates

Based on the von Kármán-type theory of plates,nonlinear bending problems of simplysupported symmetric laminated cross-ply rectangular plates under the combined action ofpressure and inplane load are investigated in this paper.The solution which satisfies thegoverning equations and boundary conditions is obtained by using the double Fourier seriesmethod.     

New Approaches to the Propagation of Nonlinear Transients in Porous Media

Many problems in regional groundwater flow require the characterization and forecasting of variables, such as hydraulic heads, hydraulic gradients, and pore velocities. These variables describe hydraulic transients propagating in an aquifer, such as a river flood wave induced through an adjacent aquifer. The characterization of aquifer variables is usually accomplished via the solution of a transient differential equation subject to time-dependent boundary conditions. Modeling nonlinear wave propagation in porous media is traditionally approached via numerical solutions of governing differential equations. Temporal or spatial numerical discretization schemes permit a simplification of the equations. However, they may generate instability, and require a numerical linearization of true nonlinear problems. Traditional analytical solutions are continuous in space and time, and render a more stable solution, but they are usually applicable to linear problems and require regular domain shapes. The method of decomposition of Adomian is an approximate analytical series to solve linear or nonlinear differential equations. It has the advantages of both analytical and numerical procedures. An important limitation is that a decomposition expansion in a given coordinate explicitly uses the boundary conditions in such axis only, but not necessarily those on the others. In this article we present improvements of the method consisting of a combination of a partial decomposition expansion in each coordinate in conjunction with successive approximation that permits the consideration of boundary conditions imposed on all of the axes of a transient multidimensional problem; transient modeling of irregularly-shaped aquifer domains; and nonlinear transient analysis of groundwater flow equations. The method yields simple solutions of dependent variables that are continuous in space and time, which easily permit the derivation of heads, gradients, seepage velocities and fluxes, thus minimizing instability. It could be valuable in preliminary analysis prior to more elaborate numerical analysis. Verification was done by comparing decomposition solutions with exact analytical solutions when available, and with controlled experiments, with reasonable agreement. The effect of linearization of mildly nonlinear saturated groundwater equations is to underestimate the magnitude of the hydraulic heads in some portions of the aquifer. In some problems, such as unsaturated infiltration, linearization yields incorrect results.     

黏弹性板的大挠度蠕变屈曲

研究了具有初始小挠度受轴向压载黏弹性板的蠕变屈曲问题，在建立控制方程时，利用了von Karman非线性应变-位移关系，并考虑了初始挠度，用标准线性固体模型描述材料的黏弹性特性，在求解非线性积分方程时，利用梯形公式计算记忆积分式，将非线性积分方程化为非线性代数方程进行数值求解，得到了结构的蠕变变形过程，又将问题退化到小挠度情况进行研究，得到了挠度随时间扩展的解析解，分析了瞬时失稳临界载荷、持久临界载荷的物理意义，讨论了考虑几何非线性对黏弹性板蠕变屈曲的影响。