Rheological characteristics of glass-fibre-filled polypropylene melts

The rheological properties of glass fibre-filled polypropylene melts have been investigated. A high pressure capillary rheometer has been used for the experimental study. The effect of shear rate, temperature, and fibre concentration on the melt viscosity and viscoelastic properties have been studied. An equation has been proposed to correlate the melt viscosity with shear rate, temperature and fibre content. A master curve relation on this basis has been brought out using the shift factora _T . a _T shift factor (=/ _r ) - A _i coefficients of the polynomical of eq. (1) (i = 0, 1, 2, ,n) - B constant in the AFE equation (eq. (2)) (Pa s) - B constant in eq. (3) - D extrudate diameter - d capillary diameter - activation energy at constant shear rate (kcal/mole) - E activation energy at constant shear stress (kcal/mole) - T melt temperature (K) - X fraction glass fibre by weight - shear rate (s^–1) - shear viscosity (Pa s) - normal stress coefficient (Pa s²) - ₁ – ₂ first normal-stress difference (Pa) - shear stress (Pa) - r at reference temperature     

Representation of the rheological properties of polymer melts in terms of complex fluidity

In dynamic rheological experiments melt behavior is usually expressed in terms of complex viscosity ^* () or complex modulusG ^* (). In contrast, we attempted to use the complex fluidity ^* () = 1/µ ^* () to represent this behavior. The main interest is to simplify the complex-plane diagram and to simplify the determination of fundamental parameters such as the Newtonian viscosity or the parameter of relaxation-time distribution when a Cole-Cole type distribution can be applied. ^* () complex shear viscosity - () real part of the complex viscosity - () imaginary part of the complex viscosity - G ^* () complex shear modulus - G() storage modulus in shear - G() loss modulus in shear - J ^* () complex shear compliance - J() storage compliance in shear - J() loss compliance in shear - shear strain - rate of strain - angular frequency (rad/s) - shear stress - loss angle - ^* () complex shear fluidity - () real part of the complex fluidity - () imaginary part of the complex fluidity - ₀ zero-viscosity - ₀ average relaxation time - h parameter of relaxation-time distribution     

Zum Mischen rheologisch inhomogener Stoffsysteme auf Einschneckenmaschinen

Zusammenfassung Das Mischen von Stoffen mit unterschiedlichen rheologischen Eigenschaften in Schneckenmaschinen ist in der Kunststoffauf- und -verarbeitung eine Standardaufgabe. Trotzdem gibt es hierfür kein zufriedenstellendes mathematisch-physikalisches Modell. Daher werden zunächst einfache Mischmodelle diskutiert. Auf der Basis dieser Modelle wird dann unter Berücksichtigung der Besonderheiten des Plastifizierextruderprozesses eine Mischgütebeziehung mathematisch formuliert. Die experimentelle Überprüfung erfolgt mit Hilfe der Grauwertanalyse extrudierter Zweistoffsysteme, bei denen ein Stoff mit Ruß eingefärbt war. Da der Mischprozeß hochgradig stochastisch ist, streuen die Meßergebnisse. Unter Berücksichtigung dieses Tatbestandes ist der theoretische Ansatz zufriedenstellend.

---

Mixing of polymer resins with different rheological properties is a usual demand in plastics processing using screw extruders. A mathematical model describing this processing problem sufficiently is not known, however. Therefore, simple mixing models will be discussed. Based on these, a concept for the calculation of mixing homogeneity will be presented, including the particular requirement of the plasticating screw process. An experimental investigation utilizes the grey-value analysis of extruded two-component materials, which in one phase is carbon-black filled. Considering the fact that the mixing process is highly random, the theoretical model leads to a good level of aggreement with the scattering measurement data.

---

b Schneckenkanalbreite - B Bandbreite der Grauwerte - c Konstante - mittlere Konzentration, bezogen auf die Grauwertbandbreite - h Höhe, Gangtiefe, Schneckenkanalhöhe - h ₀ Gangtiefe der Einzugszone - h ₁ Gangtiefe der Ausstoßzone - L Länge - gemittelte Schmelzebettlänge - n Exponent des Potenzfließgesetzes - s Standardabweichung der Grauwerte bezogen auf die Grauwertbandbreite - S Standardabweichung der Grauwerte - t Verweilzeit - t ₁ kürzeste Verweilzeit - mittlere Verweilzeit - ₀ Umfangsgeschwindigkeit - mittlere Geschwindigkeit - V Volumenstrom - w Dicke eines Kontrollelements - w Ausstreichdicke eines Kontrollelements - x Koordinate - Mittelwert der Grauwerte - y Koordinate - Scherdeformationswinkel - Scherdeformation - mittlere Scherdeformation - Schergeschwindigkeit - Viskosität - ₁ dimensionslose kürzeste Verweilzeit - dimensionsloser Volumenstrom - _LSM laminarer Schermischgrad - _{LSM, the} theoretischer laminarer Schermischgrad - _{LSM, exp} experimenteller laminarer Schermischgrad - ² Varianz der Verweilzeit im Schmelzebett - Schubspannung - Gangsteigungswinkel der Schnecke - ø Volumenanteil - dimensionslose Kennzahl     

Einfluß nichtnewtonscher Stoffeigenschaften auf die Taylor-Wirbelströmung

Zusammenfassung Nach einer kurzen Beschreibung über die Anwendung der Taylor-Wirbelströmung bei der Filtration von nichtnewtonschen Flüssigkeiten werden polymere Modellflüssigkeiten charakterisiert, die als Partikel- und Netzwerklösungen in einer Wirbelströmungsapparatur eingesetzt wurden. Die Fließkurven der Polymerlösungen zeigen aufgrund der extrem hochmolekularen Polymerproben neben strukturviskosen Erscheinungen auch dilatantes Fließverhalten mit besonderer Wirkung auf die Taylor-Wirbelströmung.Die Versuchsflüssigkeiten offenbaren vier verschiedene Typen von Strömungsinstabilitäten: spiralförmige, schwingende und stationäre Instabilitäten sowie gedämpfte Turbulenz. Während die stark strukturviskosen Netzwerklösungen alle genannten Formen aufweisen, fehlt bei den Partikellösungen die spiralförmige Instabilität.Unter Zuhilfenahme des Hantelmolekülmodells zur Beschreibung viskoelastischer Strömungsphänomene gelingt es, durch Einführung einer kritischen Deborahzahl den Einsatzpunkt nichtnewtonscher Taylorströmungseffekte vorauszusagen. Die gefundene Beziehung steht in engem Zusammenhang mit dehnviskositätserhöhenden Polymerwirkungen in Porenströmungen und mit reibungsmindernden Polymereffekten in turbulenten Rohrströmungen.

---

Experimental investigations dealing with dilute polymer solutions are described after a short review of the application of Taylor-vortex flow in the filtration processes of non-Newtonian fluids. The test fluids represent both viscoelastic solutions with isolated macromolecules and network solutions with power law fluid behaviour.These solutions show four different types of flow instabilities: spiral-shaped, oscillatory, steady and turbulent phenomena. The Taylor-numbers which depend upon the polymer concentration are determined for the onset of these instability types. For isolated macromolecule solutions, the Deborah-number concept for dilute dumbbell solutions can be applied to describe the first appearance of irregular nonstationary Taylor vortices.The present data are compared to literature values. This fluid behaviour is related to extensional viscosity increases which are also observed in porous media flow and turbulent pipe flow of dilute macromolecular solutions.

---

Nomenklatur A, B Konstanten aus Randbedingungen der Ringspaltströmung - C Polymerkonzentration - D Schergeschwindigkeit - De Deborahzahl - l Länge einer Wirbelzelle - L Zylinderlänge - m Gesamtanzahl der Wirbelpaare zur Bestimmung der Wellenzahl - M Molmasse der Polymere - M _w Gewichtsmittel der Molmasse - M _v Viskositätsmittel der Molmasse - n Drehzahl des Rotors - universelle Gaskonstante - r Radius - R _a Radius des Außenzylinders - R _i Radius des Innenzylinders - s Spaltweite - s ^* dimensionslose Spaltweite - T Temperatur - Ta Taylorzahl - v Umfangsgeschwindigkeit - z Anzahl der Wirbelpaare zur Bestimmung der Wellenzahl Griechische Symbole Deformationskoeffizient von Makromolekülen - Wellenzahl - Dehnrate - dynamische Viskosität - [] Grenzviskositätszahl - Relaxationszeit - Dichte - Schubspannung - Winkelgeschwindigkeit - _a Winkelgeschwindigkeit des Außenzylinders - _i Winkelgeschwindigkeit des Innenzylinders Indices c kritisch (erstmaliges Auftreten von Taylorwirbel) - N newtonsch - o onset, Schwellwert - P polymer - r radial - Sch schwingend - Spir spiralförmig - Stat stationär - Turb turbulent - T Taylorströmung - Umfangsrichtung Herrn Prof. Dr. Heinz Harnisch zum 60. Geburtstag gewidmet     

Some aspects of dilute suspension theory

A theory proposed by the author as representative of the flow of a general suspension contains three interaction forces, f, S and N. For a quasi-concentrated suspension and for a dilute suspension, N and S, N are omitted, respectively. For the latter special case, we treat diffusion of a fluid through an elastic solid. For a quasi-concentrated suspension, we show that F and S depend on the gradient of the motion gradient. We demonstrate the existence of interesting phenomena: non-simple behavior, dissipative effects, generalized lift and drag forces.Presented at the second conference Recent Developments in Structured Continua, May 23 – 25, 1990, in Sherbrooke, Québec, Canada.     

Evaluating Herschel-Bulkley fluids with the back extrusion (annular pumping) technique

A mathematical model was developed to describe the behavior of Herschel-Bulkley fluids in a back extrusion (annular pumping) device. A technique was also developed to determine the rheological properties (yield stress, flow behavior index, and consistency coefficient) of these fluids. Mathematical terms were expressed in four dimensionless terms, and graphical aids and tables were prepared to facilitate the handling of the expressions.Nomenclature a radius of the plunger, m - dv/dr shear rate, s^–1 - F force applied to the plunger, N - F _b buoyancy force, N - F _cb force corrected for buoyancy, N - F _T recorded force just before the plunger is stopped, N - F _Te recorded force after the plunger is stopped, N - g acceleration due to gravity, m/s² - H(t) momentary height between plunger and container bottom, m - K a/R, dimensionless - L length of annular region, m - L(t) depth of plunger penetration, m - n flow behavior index, dimensionless - p static pressure, Pa - P _L pressure in excess of hydrostatic pressure at the plunger base, Pa - p ₀ pressure at entrance to annulus, Pa - P pressure drop per unit of length, Pa/m - Q total volumetric flow rate through the annulus, m³/s - r radial coordinate, measured from common axis of cylinder forming annulus, m - R radius of outer cylinder of annulus, m - s reciprocal of n, dimensionless - t time, s - T dimensionless shear stress, defined in Eq. (3) - T ₀ dimensionless yield stress, defined in Eq. (4) - T _w dimensionless shear stress at the plunger wall - _p velocity of plunger, m/s - velocity, m/s - mass density of fluid, kg/m³ - Newtonian viscosity, Pa s - P p ₀ –p _L , Pa - consistency coefficient, Pa sⁿ - value of where shear stress is zero - _–, ₊ limits of the plug flow region (Fig. 1) - r/R - shear stress, Pa - _y yield stress, Pa - _w shear stress at the plunger wall, Pa - dimensionless flow rate defined in Eq. (24) - dimensionless velocity defined by Eq. (5) - _–, ₊ dimensionless velocity outside the plug flow region - _max dimensionless maximum velocity in the plug flow region - _p dimensionless velocity at the plunger wall     

Evaluation of the dynamic-mechanical properties of solids from a cooperative model for stress relaxation

For many solid materials the stress relaxation process obeys the universal relationF = – (d/d lnt)_max = (0.1 ± 0.01) ( ₀ — _i ), regardless of the structure of the material. Here denotes the stress,t the time, ₀ the initial stress of the experiment and _i the internal stress. A cooperative model accounting for the similarity in relaxation behaviour between different materials was developed earlier. Since this model has a spectral character, the concepts of linear viscoelasticity are used here to evaluate the corresponding prediction of the dynamic mechanical properties, i.e. the frequency dependence of the storageE () and lossE () moduli. Useful numerical approximations ofE () andE () are also evaluated. It is noted that the universal relation in stress relaxation had a counterpart in the frequency dependence ofE (). The theoretical prediction of the loss factor for high-density polyethylene is compared with experimental results. The agreement is good.     

Experimental studies of suspended ferromagnetic fibers in a magnetic field

The analysis of the rotation of a ferromagnetic ellipsoid suspended in a Newtonian fluid and subjected to a uniform magnetic field is extended to include a long, slender cylindrical fiber which is magnetically saturated. Experimental observations of rotating nickel cylinders with aspect ratiosL/D ranging from 5 to 40 agree with the theoretical predictions that: (1) the proper magnetoviscous time constant for the motion is _MV = _s/µ ₀ M _s ² , (2) larger fiber aspect ratios result in considerably longer orientation times; and (3) the strength of the applied external field has only a slight effect on the overall fiber rotation, and has no effect on the maximum angular velocity achieved. Quantitative agreement of theory and experiments is obtained for fibers withL/D 20; for the shorter fibers, the theory tends to overpredict the fiber rotation rate by as much as 30%. D diameter of the cylinder - D ^P (r) position-dependent demagnetization tensor, implicitly defined in eq. (2.5) - D _xx,D _yy,D _zz volume-averaged demagnetizing factors for an ellipsoid equivalent to a uniformly magnetized cylinder, defined in eq. (2.6) - H _i ;H _i magnetic field inside a ferromagnetic body; magnitude ofH _i - H ₀;H ₀ magnetic field applied by external sources; magnitude ofH ₀ - k geometric parameter in the hydrodynamic resistance of a body rotating in a Newtonian fluid, eq. (2.2) - L length of the cylinder - L ^(h);L _z ^(h) hydrodynamic torque exerted on a rotating body; thez-component ofL ^(h) on the cylinder - L ^(m);L _z ^(m) magnetic torque exerted on a magnetic body in a magnetic field, eq. (2.4); thez-component ofL ^(m) on the cylinder - M the magnetization of a magnetic material - M _s the saturation magnitude ofM, approached by all ferromagnetic materials asH _i becomes large - r position vector of a point within a ferromagnetic body - V volume of a magnetic particle - x, y, z rectangular coordinate axes fixed in the cylinder according to figure 1 - angle of inclination of the axis of the cylinder with respect toH ₀ - shear rate - small parameter of slender body theory,=1/ln (2L/D) - _s constant viscosity of the suspending fluid - µ ₀ the magnetic permeability of free space,µ ₀=4 · 10^–7 H/m - _MV the magnetoviscous time constant, a characteristic time for a process involving a competition of viscous and magnetic stresses - ₁ the first normal-stress coefficient - ; _z angular velocity of a rotating body; angular velocity of a cylinder about thez-axis, _z =– d/dt     

Fractal-time stochastic processes and dynamic functions of polymeric systems

Dynamic material functions of polymeric systems are calculated via a defect-diffusion model. The random motion of defects is modelled by a fractaltime stochastic process. It is shown that the dynamic functions of polymeric solutions can be approximated by the defect-diffusion process of the mixed type. The relaxation modulus of Kohlrausch type is obtained for a fractal-time defect-diffusion process, and it is shown that this modulus is capable of portraying the dynamic behavior of typical viscoelastic solutions.The Fourier transforms of the Kohlrausch function are calculated to obtain and. A three-parameter model for and is compared with the previous calculations. Experimental measurements for five polymer solutions are compared with model predictions. D rate of deformation tensor - G(t) mechanical relaxation modulus - H relaxation spectrum - I(t) flux of defects - P _n (s) probability of finding a walker ats aftern-steps - P generating function ofP _n (s) - s(t) fraction of surviving defects - , () gamma function (incomplete) - ₀ zero shear viscosity - ^* () complex viscosity - frequency - t _n n-th moment - F[] Fourier transform - f ^* (u) Laplace transform off(t) - , components of ^* - G _f, _f ^* fractional model - G ₃, ₃ ^* three parameter model - complex conjugate ofz - material time derivative ofD     

Viscous heating correction for thermally developing flows in slit die viscometry

In the thermally developing region, d _yy /dx| _y=h varies along the flow direction x, where _yy denotes the component of stress normal to the y-plane; y = ±h at the die walls. A finite element method for two-dimensional Newtonian flow in a parallel slit was used to obtain an equation relating d _yy /dx/ _y=h and the wall shear stress ₀ at the inlet; isothermal slit walls were used for the calculation and the inlet liquid temperature T₀ was assumed to be equal to the wall temperature. For a temperature-viscosity relation /₀ = [1+(T–T₀]^–1, a simple expression [(hd _yy /dx/ _y=h )/ _w0] = 1–[1-F _c(Na)] [M()+P(Pr) ·Q(Gz ^–1)] was found to hold over the practical range of parameters involved, where Na, Gz, and Pr denote the Nahme-Griffith number, Graetz number, and Prandtl number; is a dimensionless variable which depends on Na and Gz. An order-of-magnitude analysis for momentum and energy equations supports the validity of this expression. The function F _c(Na) was obtained from an analytical solution for thermally developed flow; F _c(Na) = 1 for isothermal flow. M(), P(Pr), and Q(Gz) were obtained by fitting numerical results with simple equations. The wall shear rate at the inlet can be calculated from the flow rate Q using the isothermal equation.Notation x,y Cartesian coordinates (Fig. 2) - , dimensionless spatial variables [Eq. (16)] - dimensionless variable, : = Gz(x)^–1 - dimensionless variable [Eq. (28)] - t,t ^* time, dimensionless time [Eq. (16)] - , velocity vector, dimensionless velocity vector - _x , velocity in x-direction, dimensionless velocity - _y , velocity in y-direction, dimensionless velocity - V average velocity in x-direction - _yy , ^* normal stress on y-planes, dimensionless normal stress - shear stress on y-planes acting in x-direction - _w , _w ^* value of shear stress stress at the wall, dimensionless wall shear stress - _w0, _w0 ^* wall shear stress at the inlet, dimensionless variable - , ^* rate-of-strain tensor, dimensionless tensor - wall shear rate, wall shear rate at the inlet - Q flow rate - T, T ₀, temperature, temperature at the wall and at the inlet, dimensionless temperature - h, w half the die height, width of the die - l,L the distance between the inlet and the slot region, total die length - T ₂, T ₃, T ₄ pressure transducers in the High Shear Rate Viscometer (HSRV) (Fig. 1) - P, P2, P3 pressure, liquid pressures applied to T ₂ and T ₃ - , ₀, ^* viscosity, viscosity at T = T ₀, dimensionless viscosity - viscosity-temperature coefficient [Eq. (8)] - k thermal conductivity - C _p specific heat at constant pressure - Re Reynolds number - Na Nahme-Griffith number - Gz Graetz number - Pr Prandtl number     

On some nearly viscometric flows of viscoelastic liquids

Superposition of oscillatory shear imposed from the boundary and through pressure gradient oscillations and simple shear is investigated. The integral fluid with fading memory shows flow enhancement effects due to the nonlinear structure. Closed-form expressions for the change in the mass transport rate are given at the lowest significant order in the perturbation algorithm. The elasticity of the liquid plays as important a role in determining the enhancement as does the shear dependent viscosity. Coupling of shear thinning and elasticity may produce sharp increases in the flow rate. The interaction of oscillatory shear components may generate a steady flow, either longitudinal or orthogonal, resulting in increases in flow rates akin to resonance, and due to frequency cancellation, even in the absence of a mean gradient. An algorithm to determine the constitutive functions of the integral fluid of order three is outlined.Nomenclature A _n Rivlin-Ericksen tensor of order . - A _k Non-oscillatory component of the first order linear viscoelastic oscillatory velocity field induced by the kth wave in the pressure gradient - d Half the gap between the plates - e _x, e _z Unit vectors in the longitudinal and orthogonal directions, respectively - G(s) Relaxation modulus - G History of the deformation - Stress response functional - I() Enhancement defined as the ratio of the frequency dependent part of the discharge to the frequencyindependent part of it at the third order - I ^*() Enhancement defined as the ratio of the increase in discharge due to oscillations to the total discharge without the oscillations - k Power index in the relaxation modulus G(s) - k _i ^–1 Relaxation times in the Maxwell representation of the quadratic shear relaxation modulus (s ₁, s ₂) - m _i ^–1, n _i ^–1 Relaxation times in the Maxwell representations of the constitutive functions ₁(s ₁,s ₂,s ₃) and ₄ (s ₁, s ₂,s ₃), respectively - P Constant longitudinal pressure gradient - p Pressure field - _mx ,⁽³⁾ _nz ,⁽³⁾ Mean volume transport rates at the third order in the longitudinal and orthogonal directions, respectively - ₀,⁽³⁾, ₁,⁽³⁾ Frequency independent and dependent volume transport rates, respectively, at the third order - s = t- Difference between present and past times t and      

Influence of the formation of associations of macromolecules on the rheo-optical properties of their dilute solutions. I. Theory

Assuming the formation of doublets in the flow according to a mass action law, the shear rate and the concentration dependence of the extinction angle, of the birefringence, and of the average coil expansion are calculated for dilute solutions of flexible macromolecules. It is shown that this reversible association process has a strong influence on the measurable parameters in a flow birefringence experiment. c concentration (g/cm³) - h ² mean square end-to-end distance at shear rate - h ₀ ² mean-square end-to-end distance at zero-shear rate - n refractive index of the solution (not very different from the solvent for a very dilute solution) - E mean coil expansion - K ₀,K constant of the mass action law - M molecular weight - R _G gas constant - T absolute temperature - ₁ – ₂ optical anisotropy of the segment - ₀ Deborah number: - Deborah number: - shear rate - ₀, reduced concentration - _s viscosity of the solvent - [] ₀ intrinsic viscosity at zero-shear rate - [] intrinsic viscosity at shear rate - extinction angle - N _a Avodagro's number - _n magnitude of the birefringence     

Caractéristiques rhéologiques,coéfficient de frottement et écoulement en situation réelle de fluides à seuil

Résumé Ce travail porte sur l'étude de solutions diluées d'un polymère de l'acide acrylique dans l'eau (concentration en poids 0,1%). Ce fluide présente des effets de seuil. La mesure du champ de vitesse par vélocimétrie laser permet une détermination précise de l'indice rhéologique,n, étant un paramètre essentiel de la loi de comportement proposée: . Les autres constantes peuvent être déduites d'essais rhéologiques classiques, à fort taux de cisaillement. Il est possible de corriger le gradient de pression mesuréP/L, afin d'obtenir la valeur véritable de ce gradient, notéedp/dz. L'analyse de l'écoulement dans un élargissement brusque montre que le seuil a une forte influence sur les zones de recirculation.

---

This work deals with the study of very dilute solutions of polyacrylic acid in water (weight concentration about 0.1%). These fluids seem to exhibit a yield effect. The determination of the fully developed velocity field by laser velocimetry allows us an accurate determination of the rheological indexn which is an essential parameter for the proposed rheological relationship: . Other constants can be determined from classical rheological experiments (high shear strain). It is possible to correct the experimental pressure gradientP/L so as to get the real value, noted asdp/dz. An analysis of the flow in an abrupt expansion shows that the yield effect strongly influences the recirculation zones.

---

D, d m diamètre intérieur d'une conduite cylindrique - C % concentration en poids - _s Pa seuil de contrainte - K consistance - gradient de vitesse axiale - gradient pariétal de vitesse axiale - Pa s viscosité pour - Pa contrainte de cisaillement - m/s vitesse débitante - n indice de structure - dp/dz Pa/m gradient longitudinal de pression - z m abscisse longitudinale - u m/s vitesse axiale - écart entre le gradient de pression effectif et le gradient mesuré en Pa - P Pa différence de pression mesurée - L m distance entre 2 prises de pression - A Pa constante intervenant dans l'expression de - B 10^–3 Pa s constante intervenant dans l'expression de     

The hole pressure problem: On the Higashitani-Pritchard theory for transverse and axial slots

Analysis of the Higashitani-Pritchard (HP) theory for a transverse slot provides insight into the nature of the errors involved. The effects of geometry, elasticity and asymmetry on the errors in the HP theory are also discussed. Inertial effects and the effect of asymmetry are included in the HP theory for a transverse slot, through modification of the pressure term in the momentum equation; the extended HP theory proposed in this work provides evidence as to the reasons for the failure of the Newtonian hole pressure as a correction term at higher Reynolds numbers. Finally, the HP theory is used to analyse a control volume of fluid in the axial slot geometry and deduce a rigorous sufficient condition for secondary flows to exist. This analysis illustrates the nature of the role played by the second normal-stress difference (N ₂) in causing secondary flows, and suggests the possibility of the direction of the secondary flows being related to the sign ofN ₂. A computational study of all three aspects of the HP theory investigated in this work seems worth-while. x, y, z Cartesian coordinates - u, Cartesian velocity components inx andy directions - velocity vector - q ₁,q ₂,q ₃ orthogonal curvilinear coordinates - h ₁,h ₂,h ₃ scale factors of curvilinear coordinate system - P isotropic pressure - N ₁ first normal-stress difference - N ₂ second normal-stress difference - R _e Reynolds number - R _L hole-based Reynolds number (eqs. (5.3) and (5.4)) - W _e Weissenberg number - H channel height - W hole width - L hole depth - S path of zero slope of streamlines (pathS) - P _H hole pressure (eq. (2.1)) - P _I,P _E inertial and elastic pressures (eqs. (5.7–9)) - P _R pressure term used in correction for asymmetry (eqs. (5.19–21)) - P _IH,P _EH inertial and elastic hole pressures (eqs. (5.17) and (5.12)) - P _RH,P _SH,P _TH correction terms used in extended HP theory (eqs. (5.23–25)) - total stress tensor - extra-stress tensor - del operator - unit tensor - _ij, _ij components of total and extra stress tensors in curvilinear coordinate system - _w wall shear stress at pointB of figure 1 - unperturbed wall shear rate - density of fluid - viscosity of fluid - ₂ second normal-stress coefficient - _ij radius of curvature of surface of constantq _i in theq _j direction     

Pulsatile blood flow through arterioles

An analytical study was made to examine the effect of vascular deformability on the pulsatile blood flow in arterioles through the use of a suitable mathematical model. The blood in arterioles is assumed to consist of two layers — both Newtonian but with differing coefficients of viscosity. The flow characteristics of blood as well as the resistance to flow have been determined using the numerical computations of the resulting expressions. The applicability of the model is illustrated using numerical results based on the existing experimental data. r, z coordinate system - u, axial/longitudinal velocity component of blood - p pressure exerted by blood - _b density of blood - µ viscosity of blood - t time - , displacement components of the vessel wall - T _t0,T ₀ known initial stresses - density of the wall material - h thickness of the vessel wall - T _t,T stress components of the vessel - K _l,K _r components of the spring coefficient - C _l,C _r components of the friction coefficient - M _a additional mass of the mechanical model - r ₁ outer radius of the vessel - thickness of the plasma layer - r ₁ inner radius of the vessel - circular frequency of the forced oscillation - k wave number - E ₀,E _t, , _t material parameters for the arterial segment - µ _p viscosity of the plasma layer - Q total flux - Q _p flux across the plasma zone - Q _h flux across the core region - Q mean flow rate - resistance to flow - P pressure difference - l length of the segment of the vessel     

Analyse und Berechnung der Strömungsvorgänge im zylindrischen Scherspalt von Plastifizieraggregaten

Zusammenfassung Dieser Aufsatz zeigt eine Möglichkeit auf, zylindrische Scherteile einer Plastifiziereinheit, auf der strukturviskose Materialien verarbeitet werden, approximativ zu berechnen. Es ist möglich, den Volumenstrom und Druckabfall, die mittlere Schergeschwindigkeit, Scherdeformation und Schubspannung im Scherspalt zu approximieren. Durch diese Gleichungen wird eine Abschätzung der Verteil- und Zerteilvorgänge im Scherelement möglich.

---

A method is described for approximating the flow in cylindrical shearing gaps of plasticating extruder, which is applicable to shear thinning materials. It is possible to calculate the through-put and pressure drop as well as the shear rate, strain and shear stress in the gap. With these equations the distribution and separation process in shearing gaps can be evaluated.

---

D Zylinderdurchmesser - d ₁ Schnecken-Kerndurchmesser der Meteringzone - d _s Durchmesser des zylindrischen Scherteils - K Konstante im Potenzfließgesetz - K _0T Koeffizient des Potenzfließgesetzes - L ₁ Länge der Anlaufschräge - L _s Länge des zylindrischen Scherteils - n Fließindex - n ₀ Drehzahl - p Druckabfall über der Scherteillänge - s Scherspalthöhe - T _M Massetemperatur - ₀ Umfangsgeschwindigkeit - _0x Geschwindigkeitskomponente inx-Richtung - _x, _z Geschwindigkeit inx- bzw.z-Richtung als Funktion der Koordinatey - Volumenstrom - x, z Ortskoordinaten - Exponent des Potenzfließgesetzes - Schergeschwindigkeit - mittlere Schergeschwindigkeit - Viskosität - dimensionslose Höhe - Dichte der Schmelze - Schubspannung - _yx, _yz Schubspannungskomponenten - _xx, _zz Normalspannungskomponenten - _ps dimensionsloser Druckgradient - dimensionsloser Volumenstrom - _x, _z dimensionslose Geschwindigkeit inx- bzw.z-Richtung     

The steady shear viscosity of filled polymeric liquids described by a linear superposition of two relaxation mechanisms

Filled polymeric liquids often exhibit apparent yielding and shear thinning in steady shear flow. Yielding results from non-hydrodynamic particle—particle interactions, while shear thinning results from the non-Newtonian behavior of the polymer melt. A simple equation, based on the linear superposition of two relaxation mechanisms, is proposed to describe the viscosity of filled polymer melts over a wide range of shear rates and filler volume fraction.The viscosity is written as the sum of two generalized Newtonian liquid models. The resulting equation can describe a wide range of shear-thinning viscosity curves, and a hierarchy of equations is obtained by simplifying the general case. Some of the parameters in the equation can be related to the properties of the unfilled liquid and the solid volume fraction. One adjustable parameter, a yield stress, is necessary to describe the viscosity at low rates where non-hydrodynamic particle—particle interaction dominate. At high shear rates, where particle—particle interactions are dominated by interparticle hydrodynamics, no adjustable parameters are necessary. A single equation describes both the high and low shear rate regimes. Predictions of the equation closely fit published viscosity data of filled polymer melts. n power-law index - n ₁,n ₂ power-law index of first (second) term - shear rate - steady shear viscosity - ₀ zero-shear rate viscosity - _{0, 1}, _{0, 2} zero-shear rate viscosity of first (second) term - time constant - ₁, ₂ time constant of first (second) term - µ _r relative viscosity of filled Newtonian liquid - ₀ yield stress - ø solid volume fraction - ø _m maximum solid volume fraction     

Response of an elastic Bingham fluid to oscillatory shear

The response of an elastic Bingham fluid to oscillatory strain has been modeled and compared with experiments on an oil-in-water emulsion. The newly developed model includes elastic solid deformation below the yield stress (or strain), and Newtonian flow above the yield stress. In sinusoidal oscillatory deformations at low strain amplitudes the stress response is sinusoidal and in phase with the strain. At large strain amplitudes, above the yield stress, the stress response is non-linear and is out of phase with strain because of the storage and release of elastic recoverable strain. In oscillatory deformation between parallel disks the non-uniform strain in the radial direction causes the location of the yield surface to move in-and-out during each oscillation. The radial location of the yield surface is calculated and the resulting torque on the stationary disk is determined. Torque waveforms are calculated for various strains and frequencies and compared to experiments on a model oil-in-water emulsion. Model parameters are evaluated independently: the elastic modulus of the emulsion is determined from data at low strains, the yield strain is determined from the phase shift between torque and strain, and the Bingham viscosity is determined from the frequency dependence of the torque at high strains. Using these parameters the torque waveforms are predicted quantitatively for all strains and frequencies. In accord with the model predictions the phase shift is found to depend on strain but to be independent of frequency.Notation A plate strain amplitude (parallel plates) - A _R plate strain amplitude at disk edge (parallel disks) - G elastic modulus - m torque (parallel disks) - M normalized torque (parallel disks) = 2m/R ³₀ - N ratio of viscous to elastic stresses (parallel plates) =µ A/ ₀ ratio of viscous to elastic stresses (parallel disks) =µ A _R/₀ - r normalized radial position (parallel disks) =r/R - r radial position (parallel disks) - R disk radius (parallel disks) - t normalized time = t — /2 - t time - _E elastic strain - _P plate strain (displacement of top plate or disk divided by distance between plates or disks) - _PR plate strain at disk edge (parallel disks) - ₀ yield strain - _E normalized elastic strain = _E/₀ - _P normalized plate strain = _P/₀ - _PR normalized plate strain at disk edge (parallel disks) = _PR/₀ - ₀ normalized plate strain amplitude (parallel plates) =A/ ₀ — normalized plate strain amplitude at disk edge (parallel disks) =A _R/₀ - phase shift between _P andT (parallel plates) — phase shift between _PR andM (parallel disks) - µ Bingham viscosity - stress - ₀ yield stress - T normalized stress =/ ₀ - frequency     

Temperature and concentration dependent viscosity and gelation temperature of ABA triblock copolymer solutions

In solutions of ABA-triblock copolymers in a poor solvent for A thermoreversible gelation can occur. A three-dimensional dynamic network may form and, given the polymer and the solvent, its structure will depend on temperature and polymer mass fraction. The zero-shear rate viscosity of solutions of the triblock-copolymer polystyrene-polyisoprene-polystyrene in n-tetradecane was measured as a function of temperature and polymer mass fraction, and analyzed; the polystyrene blocks contained about 100 monomers, the polyisoprene blocks about 2000 monomers. Empirically, in the viscosity at constant mass fraction plotted versus inverse temperature, two contributions could be discerned; one contribution dominating at high and the other one dominating at low temperatures. In a comparison with theory, the contribution dominating at low temperatures was identified with the Lodge transient network viscosity; some questions remain to be answered, however. An earlier proposal for defining the gelation temperature T _gel is specified for the systems considered, and leads to a gelation curve; T _gel as a function of polymer mass fraction.Mathematical symbols {} functional dependence; e.g., f{x} means f is a function of x - p _log logarithm to the base number p; e.g., ¹⁰log is the common logarithm - exp exponential function with base number e - sin trigonometric sine function - lim limit operation - – in integral sign: Cauchy Principal Value of integral, e.g., - derivative to x - partial derivative to x Latin symbols dimensionless constant - b constant with dimension of absolute temperature - constant with dimension of absolute temperature - B dimensionless constant - c mass fraction - dimensionless constant - constant with dimension of absolute temperature - d ^* dimensionless constant - D{0} constant with dimension of absolute temperature - e base number of natural (or Naperian) logarithm - g distribution function of inverse relaxation times - G relaxation strength relaxation function - h distribution function of relaxation times reaction constant enthalpy of a molecule - H Heaviside unit step function - i complex number defined by i ² = –1 - j{0} constant with dimension of viscosity - j index number - k Boltzmann's constant - k _H Huggins' coefficient - m mass of a molecule - n number - N number - p index number - s entropy of a molecule - t time - T absolute temperature Greek symbols as index: type of polymer molecule - as index: type of polymer molecule - shear as index: type of polymer molecule - shear rate - small variation; e.g. T is a small variation in T relative deviation Dirac delta distribution as index: type of polymer molecule - difference; e.g. is a difference in chemical potential - constant with dimension of absolute temperature - (complex) viscosity - constant with dimension of viscosity - [] intrinsic viscosity number - inverse of relaxation time - chemical potential - number pi; circle circumference divided by its diameter - mass per unit volume - relaxation time shear stress - angular frequency     

Rheological models for gypsum plaster pastes

Shear stress and shear rate data obtained for gypsum plaster pastes were correlated by means of different rheological models. The pastes were prepared from a commercial calcium sulfate hemihydrate at various water/plaster ratios ranging from 100/150 to 100/190. The tests were performed at 25°C using a rotating coaxial cylinder viscosimeter. The measurements were accomplished by applying a step-wise decreasing shear rate sequence. Discrimination among the models was made: (1) on the basis of the fitting goodness; (2) by checking the physical meaning of the calculated parameters; (3) on the basis of the stability of the parameters and of their prediction capacity beyond the limits of the experimental data. In the light of above, the Casson model seemed to be most effective for application to gypsum plaster pastes. K Consistency - n Power-law index - N Number of experimental data - P Number of parameters - Shear rate (s^–1) - ₀ Viscosity (Pa · s) - _d Dispersing medium viscosity (Pa · s) - _p Plastic viscosity (Pa · s) - Viscosity at zero shear rate (Pa · s) - Viscosity at infinite shear rate (Pa · s) - [] Intrinsic viscosity - ² Variance - Shear stress (Pa) - ₀ Yield stress (Pa) - Solid volume fraction - _m Maximum solid volume fraction