胶凝原油蠕变的时间-温度-应力等效性

黏弹性蠕变是胶凝原油重要的流变特性,要描述胶凝原油的黏弹性蠕变行为,必须同时考虑 应力、时间和温度等参数. 于是对胶凝原油进行了不同应力和不同温度下的蠕变实验,利用 时间-温度-应力等效原理分析了胶凝原油的非线性蠕变行为,得到了参考应力和参考温度下 的蠕变主曲线,并用黏弹性流变模型拟合得到了蠕变主曲线的表达式. 从而可以分别通过较 高温度和应力水平下的短期蠕变行为来预测较低温度和应力水平下的长期蠕变行为.     

非线性粘弹体的时间-温度-应力等效原理及其应用

考虑粘弹性材料特征时间的应力相关性,认为应力水平与温度、压力、溶剂浓度、损伤及老化等材料特征时间的影响相似,有其等效性。依自由体积理论,推导了温度－应力移位因子的表达式,提出了时间－温度－应力等 效原理。应用此原理,可以将不同温度和应力水平下的儒变曲线移位成某一参考温度和参考应力水平下的主曲线,从而可以通过较高温度和应力水平下的短期蠕变行为来预测较低温度和应力水平下的较长期的蠕变行为。实例分析了高密度聚乙烯（HDPE）非线性蠕变行为的－应力等效性。     

LONG-TERM CREEP ASSESSMENT OF VISCOELASTIC POLYMER BY TIME-TEMPERATURE-STRESS SUPERPOSITION

Nonlinear viscoelastic creep properties of poly (methyl methacrylate) at various temperatures and stress levels were measured in short-term tests to check the applicability of time-temperature-stress superposition principle, which is the combined form of time-temperature superposition principle and time-stress superposition principle. A unified master creep compliance curve was constructed from the short-term tests by joint application of time-temperature superposition and time-stress superposition. The unified master curve establishes the creep compliance over two years, which is 4.2 decades longer than the test duration. Moreover, it is verified that in nonlinear viscoelastic cases, the time-temperature shift factors are dependent on stresses at which the shifts are applied, while the time-stress shift factors are dependent on temperatures.     

尼龙6/蒙脱土复合材料蠕变行为研究

针对经典黏弹性模型不能很好分析黏弹性材料的蠕变行为问题,运用分数阶导数的类标准线性体模型与Prony级数模型研究了黏弹性材料尼龙6/蒙脱土复合材料的蠕变行为.采用原位聚合法制备了尼龙6/蒙脱土复合材料,在室温环境下对其进行蠕变实验.然后运用分数阶导数的类标准线性体模型和Prony级数模型对复合材料的蠕变实验数据进行分析...     

A MICROMECHANICAL FRAMEWORK WITH AGGREGATE-MASTIC INTERFACE EFFECT FOR PREDICTING UNIAXIAL COMPRESSION CREEP OF ASPHALT MIXTURE

According to the elastic-viscoelastic correspondence principle, an elastic microme- chanical framework taking the inclusion-matrix interface effect into account is extended for predicting viscoelastic properties of asphalt mixture, which is simply treated as elastic coarse aggregate inclusions periodically and isotropically embedded in a viscoelastic asphalt mastic matrix. The Burgers model is adopted for characterizing the matrix mechanical behavior, so that the homogenized relaxation modulus of asphalt mixture in compression creep is derived. After a series of uniaxial compression creep tests are performed on asphalt mastic in different temperature and stress conditions in order to determine the matrix constitutive parameters, the framework presented is validated by comparison with the experiment, and then some predictions of uniaxial compression creep behavior of asphalt mixture in different temperature and stress conditions are given.     

Creep analysis with a stress range dependent constitutive model

Many materials exhibit the stress range dependent creep behavior. The power law creep observed for a certain stress range changes to the viscous type creep as the stress value decreases. Recently published experimental data for advanced heat resistant steels indicate that the high creep exponent (in the range 7–12) may decrease to the low value of approximately unity within the stress range relevant for engineering structures. The aim of this paper is to analyze the influence of the stress range dependent power-law-viscous creep transition on the behavior of structures at elevated temperature. A constitutive model for the minimum creep rate is introduced to describe both the linear and the power law creep depending upon the stress level. To demonstrate basic features of the stress range dependent creep modeling, several elementary examples from structural mechanics are presented. They include a stress relaxation problem, a beam subjected to pure bending and a pressurized thick-walled cylinder. Based on the uni-axial transition stress the transition value of the external load is estimated such that above this value the power law can be applied. For the loading levels below this value the character of the stress distribution as well as the stress values are essentially influenced by the viscous creep.     

Rate (time)-dependent deformation behavior: an overview of some properties of metals and solid polymers

The inelastic deformation behaviors of metals and polymers are discussed with the aim of finding a common base that would simplify academic and engineering analyses. Only monotonic loading conditions at room temperature are considered. For loading at different rates, nonlinear relations between loading rate and stress level, creep stress level and creep strain, and relaxation rate and stress were common to both type of materials. There are, of course, significant differences in elastic properties, strength levels and the strains involved. Special properties such as relaxation behaviors and creep anomalies can be qualitatively and quantitatively reproduced by the state variable model VBO (viscoplasticity theory based on overstress). Since experimental investigations typically concentrate on one particular aspect of inelastic deformation behavior such as creep or strain-rate dependence, it is often difficult to gather a comprehensive data set for a given material. In spite of this, considerable similitude in the deformation behavior of metals and polymers in various test conditions has nevertheless been established.     

Quasi-static properties of a photoviscoelastic material

This paper describes the results of mechanical and optical measurements in plasticized polyvinyl chloride under conditions of creep and relaxation at room temperature. It covers one task of a broader investigation aimed at developing experimental methods for viscoelastic stress analysis. The moiré method of strain analysis was found well suited for continuous recording of axial and transversal deformation in creep tests. The material exhibits linear viscoelastic behavior, both mechanical and optical. Strain, stress and birefringence measured from creep and relaxation tests gave straightline plots on log-log scale and, thus simple empirical formulas were possible to derive. The theoretical prediction that birefringence in a linear viscoelastic material not exhibiting flow can be expressed as a linear relationship of stress and strain was satisfactorily substantiated.     

A review of the rheo-optical properties of linear high polymers

Some principles ans laws, expressing the mechanical and optical behavior of linear viscoelastic materials, are reviewed. The mechanical properties of the polymers in the transition region may be represented by a condensed general method containing Ferry's modulus or compliance-reduction scheme, the time-temperature superposition principle and the Gauss error integral representation. The optical behavior of high polymers is expressed by the stress- and strain-optical coefficients in creep or relaxation, which relate birefringence to stresses or strains. It was recently shown experimentally that, instead of a pair of independent linear differential operator relations, which characterize the mechanical properties of the viscoelastic materials, only one operator relation is needed and the initial value of another at the glassy or rubbery state. Then, a single test is sufficient for the complete determination of the mechanical and optical viscoelastic behavior, provided the value of another elastic constant at the glassy or rubbery state is also determined and the variation of birefringence with time is simultaneously measured with the mechanical-characteristic quantities of the material.     

螺旋压缩弹簧应力松弛特性试验分析及其应用

本文通过应力松弛试验、理论推导及数值模拟研究了高温下螺旋压缩弹簧的应力松弛规律,并利用加速模型对工况下弹簧应力松弛服役寿命做出预测。首先,根据螺旋压缩弹簧的结构特点搭建了弹簧应力松弛连续动态测试装置,该装置不仅避免了传统测试方法存在的缺陷,而且能够保证试验过程中位移载荷恒定,并实时监测载荷变化。本文以某飞机舱门单锁机构中的螺旋压缩弹簧为试验对象进行了不同温度条件下的应力松弛试验,得到其松弛动力学曲线,并基于Arrhenius模型建立了弹簧在工况下的应力松弛服役寿命预测模型;其次,基于应力松弛和蠕变在本质上的一致性,结合金属材料蠕变规律并根据试验弹簧的受力特点,推导出用于描述试验材料松弛行为的蠕变本构方程,由试验结果获得该本构方程的材料常数;最后,通过该本构方程及材料常数,在ANSYS软件中对试验弹簧的松弛过程进行模拟,结果表明,模拟结果与试验结果误差不大于4%。因此,通过本文方法所建立的蠕变方程对弹簧在不同载荷条件下的应力松弛规律进行仿真分析具有一定的可行性与准确性。     

An experimental study of uniaxial creep,cyclic creep and relaxation of aisi type 304 stainless steel at room temperature

Following previous work (Krempl, 1979), a servocontrolled testing machine and strain measurement at the gage length were used to study the uniaxial rate(time)-dependent behavior of AISI Type 304 stainless steel at room temperature. The test results show that the creep strain accumulated in a given period of time depends strongly on the stress-rate preceding the creep test. In constant stress-rate zero-to-tension loading the creep strain accumulated in a fixed time-period at a given stress level is always higher during loading than during unloading. Continued cycling causes an exhaustion of creep ratchetting which depends on the stress-rate. Periods of creep and relaxation introduced during completely reversed plastic cycling show that the curved portions of the hysteresis loop exhibit most of the inelasticity. In the straight portions, creep and relaxation are small and there exists a region commencing after unloading where the behavior is similar to that at the origin for virgin materials. This region does not extend to zero stress.The results are at variance with creep theory and with viscoplasticity theories which assume that the yield surface expands with the stress. They support the theory of viscoplasticity based on total strain and overstress.     

物理老化对玻璃态高聚物非线性蠕变行为的影响

在不同应力水平下对经历不同老化时间的有机玻璃(PMMA)进行常温蠕变测试,分析物理老化和应力对材料蠕变柔量函数的影响.分析表明,老化时间对PMMA蠕变行为的影响满足流变简单性规律,即不同老化时间的蠕变柔量曲线可以沿对数时间轴平移而叠加到参考曲线上.取最长的老化时间为参考状态,依时间-老化时间等效原理,得到了各应力水平下的蠕变柔量主曲线.老化移位因子与老化时间在双对数坐标图上呈现线性关系,其负斜率就是老化移位率.结果表明,老化移位率随应力的增高而减小.     

Effective viscoelastic behavior of particulate polymer composites at finite concentration

Polymeric materials usually present some viscoelastic behavior. To improve the mechanical behavior of these materials, ceramics materials are often filled into the polymeric materials in form of fiber or particle. A micromechanical model was proposed to estimate the overall viscoelastic behavior for particulate polymer composites, especially for high volume concentration of filled particles. The method is based on Laplace transform technique and an elastic model including two-particle interaction. The effective creep compliance and the stress and strain relation at a constant loading rate are analyzed. The results show that the proposed method predicts a significant stiffer response than those based on Mori-Tanaka's method at high volume concentration of particles.     

Finite deformation of a polymer: experiments and modeling

The response of a polymer (polytetrafluoroethylene) to quasi-static and dynamic loading is determined and modeled. The polytetrafluoroethylene is extremely ductile and highly nonlinear in elastic as well as plastic behaviors including elastic unloading. Constitutive model developed earlier by Khan, Huang and Liang (KHL) is extended to include the responses of polymeric materials. The strain rate hardening, creep, and relaxation behaviors of polytetrafluoroethylene were determined through extensive experimental study. Based on the observation that both viscoelastic and viscoplastic deformation of polytetrafluoroethylene are time dependent and nonlinear, a phenomenalogical viscoelasto–plastic constitutive model is presented by a series connection of a viscoelastic deformation module (represented by three elements standard solid spring dashpot model), and a viscoplastic deformation module represented by KHL model. The KHL module is affected only when the stress exceeds the initial yield stress. The comparison between the predictions from the extended model and experimental data for uniaxial static and dynamic compression, creep and relaxation demonstrate that the proposed constitutive model is able to represent the observed time dependent mechanical behavior of polytetrafluoroethylene polytetrafluoroethylene qualitatively and quantitatively.     

Photomechanical behavior of cellulose acetate under viscoelastoplastic deformation

To confirm the possibilities of cellulose acetate as a material for a model analysis during viscoelastoplastic deformation, the time-dependent photomechanical properties of the material were examined by means of creep tests under constant stress and recovery tests after removal of stress. Consequently, though the strain and the fringe order of cellulose acetate during creep and recovery are greatly influenced by stress and room temperature, both of them can be described simply by a power function of time, and the coefficient of each of these formulas can be represented by a function of the ratio of active stress to yield stress only. The effect of temperature is included in the formulation of the yield stress. In addition, the strain and the fringe order can be represented by the viscous-viscoelastic model proposed by Findleyet al.,^1,2 in which both of them are divided into four components: elastic, plastic, time-dependent irrecoverable viscous and time-dependent recoverable viscoelastic. The relation between viscoelastic strain and viscoelastic fringe order, and the relation between viscous strain and viscous fringe order were verified to be equivalent to that between plastic strain and plastic fringe order, all of which do not depend on stress, temperature or time. Therefore, the strain distribution of cellulose acetate under viscoelastoplastic deformation can be determined directly from the value of the fringe order measured.     

黏弹性接触界面端附近的奇异应力场

研究蠕变加载条件下线黏弹性材料接触界面端附近的奇异应力场问题.考虑接触界面的摩擦,假设界面端的滑移方向不改变,相对滑移量微小,且其与位移同量级,由此线性化局部边界条件,根据对应原理得到Laplace变换域中的界面端应力场,导出时域中奇异应力场的卷积积分表达式.对卷积积分核函数进行数值反演,考虑接触材料的两类组合,一是持久模量具有量级上的差异,另一是持久模量接近相同.算例结果证实核函数可以用准弹性法求得的解析式较准确地近似.在此基础上,利用积分中值定理,并引入各应力分量的修正系数,得到黏弹性奇异应力场的简化式.结合核函数的数值反演结果分析修正系数表达式的取值范围,得到如下结论,若两相接触材料的持久模量相差很大,可以采用准弹性解的解析式较准确地描述界面端的奇异应力场;一般情况下,应力场不存在统一的奇异值和应力强度系数,当采用类似于准弹性解的表达式近似给出黏弹性应力场时,可以估计此近似描述的误差限.文中最后采用有限元分析黏弹性板端部嵌入部位的应力场,算例包括了黏弹性板与弹性金属支承、黏弹性板与黏弹性垫层所形成的滑移接触界面端,利用黏弹性有限元的数值结果验证理论分析所得结论的有效性.      

Interrelation of creep and relaxation for nonlinearly viscoelastic materials: application to ligament and metal

Creep and stress relaxation are known to be interrelated in linearly viscoelastic materials by an exact analytical expression. In this article, analytical interrelations are derived for nonlinearly viscoelastic materials which obey a single integral nonlinear superposition constitutive equation. The kernel is not assumed to be separable as a product of strain and time dependent parts. Superposition is fully taken into account within the single integral formulation used. Specific formulations based on power law time dependence and truncated expansions are developed. These are appropriate for weak stress and strain dependence. The interrelated constitutive formulation is applied to ligaments, in which stiffness increases with strain, stress relaxation proceeds faster than creep, and rate of creep is a function of stress and rate of relaxation is a function of strain. An interrelation was also constructed for a commercial die-cast aluminum alloy currently used in small engine applications.     

黏弹性薄板蠕变屈曲的载荷-时间特性研究

通过对黏弹性薄板压屈的稳定性分析,着重讨论了蠕变屈曲载荷－时间的特性,理论分析表明：黏弹性薄板蠕变屈曲与材料的力学性能密相关,屈曲载荷不像弹性薄板为一定值,而是与时间相关的;在一定载荷下,经过一段时间后出现延迟屈曲,相关的实验研究也证实这一重要结论;这种延迟失稳问题在工程中有其重要的意义。     

Modeling and measuring visco-elastic properties: From collagen molecules to collagen fibrils

Collagen is the main structural protein in vertebrate biology, determining the mechanical behavior of connective tissues such as tendon, bone and skin. Although extensive efforts in the study of the origin of collagen exceptional mechanical properties, a deep knowledge of the relationship between molecular structure and mechanical properties remains elusive, hindered by the complex hierarchical structure of collagen-based tissues. Understanding the viscoelastic behavior of collagenous tissues requires knowledge of the properties at each structural level. Whole tissues have been studied extensively, but less is known about the mechanical behavior at the submicron, fibrillar and molecular level. Hence, we investigate the viscoelastic properties at the molecular level by using an atomistic modeling approach, performing in silico creep tests of a collagen-like peptide. The results are compared with creep and relaxation tests at the level of isolated collagen fibrils performed previously using a micro-electro-mechanical systems platform. Individual collagen molecules present a non-linear viscoelastic behavior, with a Young's modulus increasing from 6 to 16 GPa (for strains up to 20%), a viscosity of 3.84±0.38 Pa s, and a relaxation time in the range of 0.24–0.64 ns. At the fibrils level, stress–strain–time data indicate that isolated fibrils exhibit viscoelastic behavior that could be fitted using the Maxwell–Weichert model. The fibrils showed an elastic modulus of 123±46 MPa. The time-dependent behavior was well fit using the two-time-constant Maxwell–Weichert model with a fast time response of 7±2 s and a slow time response of 102±5 s.     

Predictions of nonlinear viscoelastic behavior using a hybrid approach

An approach for nonlinear viscoelastic characterization is presented which uses the combined measurements from creep and dynamic mechanical tests. Although the methodology should extend to several materials and geometries, this research concentrates on thin film polymers used in the manufacture of high altitude scientific balloons. Typically, the constitutive behavior of these materials is characterized through the use of linear viscoelastic techniques. Although this linear approach provides an accurate model for small strains or loads, these materials have been shown to be highly stress dependent and, consequently, it is necessary to identify this nonlinear behavior. Traditional creep measurements require extensive laboratory test times, yet the results obtained from dynamic mechanical analysis provide the capability to predict long term material performance without a lengthy experimentation program. However, dynamic mechanical methods are currently limited to linear response; thus, an approach is presented in which the stress-dependent behavior is derived from short-term creep measurements in a manner analogous to time-temperature superposition. Predictions of material response using linear and nonlinear approaches are compared with experimental results obtained from traditional long-term creep tests. Although linear pre-dictions deteriorate for large stresses, excellent agreement is shown for the nonlinear model.