Experimental study of vortex–structure interaction noise radiated from rod–airfoil configurations

Vortex–structure interaction noise radiated from an airfoil embedded in the wake of a rod is investigated experimentally in an anechoic wind tunnel by means of a phased microphone array for acoustic tests and particle image velocimetry (PIV) for the flow field measurements. The rod–airfoil configuration is varied by changing the rod diameter (D), adjusting the cross-stream position (Y) of the rod and the streamwise gap (L) between the rod and the airfoil leading edge. Two noise control concepts, including “air blowing” on the upstream rod and a soft-vane leading edge on the airfoil, are applied to control the vortex–structure interaction noise. The motivation behind this study is to investigate the effects of the three parameters on the characteristics of the radiated noise and then explore the influences of the noise control concepts. Both the vortex–structure interaction noise and the rod vortex shedding tonal noise are analysed. The acoustic test results show that both the position and magnitude of the dominant noise source of the rod–airfoil model are highly dependent on the parameters considered. In the case where the vortex–structure interaction noise is dominant, the application of the air blowing and the soft vane can effectively attenuate the interaction noise. Flow field measurements suggest that the intensity of the vortex–structure interaction and the flow impingement on the airfoil leading edge are suppressed by the control methods, giving a reduction in noise.     

Effect of vortex shedding in unsteady aerodynamic forces for a low Reynolds number stationary wing at low angle of attack

This study elucidates the relation between wake vortex shedding and aerodynamic force fluctuations for a low Reynolds number wing from time resolved particle image velocimetry (TR-PIV) experimental measurements. The results reveal a periodic lift and drag variation within the shedding cycle and resolve the frequencies of those fluctuations from a proper orthogonal decomposition (POD) and power spectral density (PSD) analysis. To show the effect of vortex shedding on the body force fluctuations, the evolution of instantaneous aerodynamic forces is compared to the pressure field of the fluid flow and to the vortical structures in the wake of the airfoil. A six step model describing the vortex-force relation is proposed. It shows that changes in lift such as maximum lift and minimum lift are associated with the detachment of a vortex. It also shows that the minimum or local minimum drag value is obtained at the onset formation of a vortex on the airfoil wake. Similarly, the maximum or local maximum drag is obtained at the onset formation of the saddle on the airfoil wake. The model further explains the asymmetry observed in the unsteady drag force evolution. The model can be used to optimize flow control and fluid-structure interaction applications.     

Feedback control of laminar flow separation on NACA23012 airfoil by POD analysis and using perturbed Navier‐Stokes equations

The main purpose of this article is to develop a forced reduced‐order model based on the proper orthogonal decomposition (POD)/Galerkin projection (on isentropic Navier‐Stokes equations) and perturbation method on the compressible Navier‐Stokes equations. The resulting forced reduced‐order model will be used in optimal control of the separated flow over a NACA23012 airfoil at Mach number of 0.2, Reynolds number of 800, and high incidence angle of 24°. The main disadvantage of the POD/Galerkin projection method for control purposes is that controlling parameters do not show up explicitly in the resulting reduced‐order system. The perturbation method and POD/Galerkin projection on the isentropic Navier‐Stokes equations introduce a forced reduced‐order model that can predict the time varying influence of the controlling parameters and the Navier‐Stokes response to external excitations. An optimal control theory based on forced reduced‐order system is used to design a control law for a nonlinear reduced‐order system, which attempts to minimize the vorticity content in the flow field. The test bed is a laminar flow over NACA23012 airfoil actuated by a suction jet at 12% to 18% chord from leading edge and a pair of blowing/suction jets at 15% to 18% and 24% to 30% chord from leading edge, respectively. The results show that wall jet can significantly influence the flow field, remove separation bubbles, and increase the lift coefficient up to 22%, while the perturbation method can predict the flow field in an accurate manner.     

Optimal Control of a Vortex Trapped by an Airfoil with a Cavity

An airfoil with a cavity traps a vortex; the lift increases but the vortex shows great receptivity to upstream disturbances. A simple potential flow model confirms that the vortex stability basin is of a reduced extent. In this paper we present a control technique stabilizing the vortex position based on a potential flow model. The actuators are sources/sinks at the wall and the suction/blowing law is obtained by the adjoint optimization method. This revised version was published online in July 2006 with corrections to the Cover Date.     

Using the perturbation method to solve the problem of separated incompressible flow past thin airfoils

A model for separated incompressible flow past thin airfoils in the neighborhood of the “shockless entrance” condition is constructed based on the averaging of the vortex shedding flow past the airfoil edges. By approximation of the vortex shedding by two vortex curves, determination of the average hydrodynamic parameters is reduced to a twofold solution of an integral singular equation equivalent to the equation describing steady-state nonseparated airfoil flow. In this case, the calculation time is two orders of magnitude smaller than the time required for the solution of the corresponding evolution problem. The results of a test calculation using the proposed method are in fair agreement with available results of calculations and experiments. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 47, No. 3, pp. 49–63, May–June, 2006.     

Experimental investigation of a blunt trailing edge flow field with application to sound generation

The unsteady lift generated by turbulence at the trailing edge of an airfoil is a source of radiated sound. The objective of the present research was to measure the velocity field in the near wake region of an asymmetric beveled trailing edge in order to determine the flow mechanisms responsible for the generation of trailing edge noise. Two component velocity measurements were acquired using particle image velocimetry. The chord Reynolds number was 1.9 × 10⁶. The data show velocity field realizations that were typical of a wake flow containing an asymmetric periodic vortex shedding. A phase average decomposition of the velocity field with respect to this shedding process was utilized to separate the large scale turbulent motions that occurred at the vortex shedding frequency (i.e., those responsible for the production of tonal noise) from the smaller scale turbulent motions, which were interpreted to be responsible for the production of broadband sound. The small scale turbulence was found to be dependent on the phase of the vortex shedding process implying a dependence of the broadband sound generated by the trailing edge on the phase of the vortex shedding process.     

定常吹气对倾转旋翼机向下载荷的影响

为进一步提高倾转旋翼机悬停状态下的有效载重,开展了定常吹气流动控制对向下载荷的影响研究。首先应用延迟脱体涡模拟(DDES)方法对翼型-90°迎角下非定常大范围分离流动结构进行了数值分析;然后分别开展了前缘吹气、后缘吹气降载措施研究,揭示了吹气降载的机理,并对不同吹气口位置和吹气动量系数的影响进行了定量分析,最后开展了前、后缘同时吹气作用下降载数值模拟研究。计算结果表明:前缘最佳吹气位置在翼型的前缘点,而后缘吹气最佳位置位于襟翼弦长的15%处;前缘吹气的降载效果要优于后缘吹气,而且吹气动量系数对向下载荷的影响较小;相对于初始未施加流动控制构型,阻力系数减小量可达到32.72%。     

A reduced‐order approach for optimal control of fluids using proper orthogonal decomposition

In this article, a reduced‐order modeling approach, suitable for active control of fluid dynamical systems, based on proper orthogonal decomposition (POD) is presented. The rationale behind the reduced‐order modeling is that numerical simulation of Navier–Stokes equations is still too costly for the purpose of optimization and control of unsteady flows. The possibility of obtaining reduced‐order models that reduce the computational complexity associated with the Navier–Stokes equations is examined while capturing the essential dynamics by using the POD. The POD allows the extraction of a reduced set of basis functions, perhaps just a few, from a computational or experimental database through an eigenvalue analysis. The solution is then obtained as a linear combination of this reduced set of basis functions by means of Galerkin projection. This makes it attractive for optimal control and estimation of systems governed by partial differential equations (PDEs). It is used here in active control of fluid flows governed by the Navier–Stokes equations. In particular, flow over a backward‐facing step is considered. Reduced‐order models/low‐dimensional dynamical models for this system are obtained using POD basis functions (global) from the finite element discretizations of the Navier–Stokes equations. Their effectiveness in flow control applications is shown on a recirculation control problem using blowing on the channel boundary. Implementational issues are discussed and numerical experiments are presented. Copyright © 2000 John Wiley & Sons, Ltd.     

Effect of novel synthetic jet on wake vortex shedding modes of a circular cylinder

A novel actuator signal achieved by changing the ratio of the suction duty cycle to the blowing duty cycle is adopted to enhance the control effect of the synthetic jet for the flow around a circular cylinder. The suction duty cycle factor k defined as the ratio between the time duration of the suction cycle and the blowing cycle and the equivalent momentum coefficient C_μ are introduced as the determining parameters. The synthetic jet is positioned at the rear stagnation point in order to introduce symmetric perturbations upon the flow field. The proper orthogonal decomposition (POD) technique is applied for the analysis of the spanwise vorticity field. Increasing the suction duty cycle factor, the momentum coefficient is enhanced, and thus a stronger and larger scale synthetic jet vortex pair with a higher convection velocity is generated. The synthetic jet vortex pair interacts with the spanwise vorticity shear layers behind both sides of the cylinder, resulting in the variations of the wake vortex shedding modes at Re=950: for k=0.25, C_μ=0.148, vortex synchronization at the subharmonic excitation frequency with antisymmetric shedding mode; for 0.50≤k≤1.00, 0.213≤C_μ≤0.378, vortex synchronization at the excitation frequency with the symmetric or antisymmetric shedding modes; for 2.00≤k≤4.00, 0.850≤C_μ≤2.362, vortex synchronization at the excitation frequency with symmetric shedding mode. Hence, the control effect of the synthetic jet upon the wake vortex of a circular cylinder can be enhanced by increasing the suction duty cycle factor so as to increase the momentum coefficient. This is also validated at a higher Reynolds number Re=1600.     

NUMERICAL STUDY ON THE FLOW AROUND A CIRCULAR CYLINDER WITH SURFACE SUCTION OR BLOWING USING VORTICITY-VELOCITY METHOD

A vorticity-velocity method was used to study the incompressible viscous fluid flow around a circular cylinder with surface suction or blowing. The resulted high order implicit difference equations were effeciently solved by the modified incomplete LU decomposition conjugate gradient scheme (MILU-CG). The effects of surface suction or blowing ' s position and strength on the vortex structures in the cylinder wake, as well as on the drag and lift forces at Reynoldes number Re = 100 were investigated numerically. The results show that the suction on the shoulder of the cylinder or the blowing on the rear of the cylinder can effeciently suppress the asymmetry of the vortex wake in the transverse direction and greatly reduce the lift force; the suction on the shoulder of the cylinder, when its strength is properly chosen , can reduce the drag force significantly , too.     

Input-output reduced-order modeling of unsteady flow over an airfoil at a high angle of attack based on dynamic mode decomposition with control

Due to the damage caused by stall flutter, the investigation and modeling of the flow over a wind turbine airfoil at high angles of attack are essential. Dynamic mode decomposition (DMD) and dynamic mode decomposition with control (DMDc) are used to analyze unsteady flow and identify the intrinsic dynamics. The DMDc algorithm is found to have an identification problem when the spatial dimension of the training data is larger than the number of snapshots. IDMDc, a variant algorithm based on reduced dimension data, is introduced to identify the precise intrinsic dynamics. DMD, DMDc and IDMDc are all used to decompose the data for unsteady flow over the S809 airfoil that are obtained by numerical simulations. The DMD results show that the dominant feature of a static airfoil is the adjacent shedding vortices in the wake. For an oscillating airfoil, the DMDc results may fail to consider the effect of the input and have an identification problem. IDMDc can alleviate this problem. The dominant IDMDc modes show that the intrinsic flow for the oscillating case is similar to the unsteady flow over the static airfoil. Moreover, the input–output model identified by IDMDc can give better predictions for different oscillating cases than the identified DMDc model.     

Investigation of three-dimensional dynamic stall on an airfoil using fast-response pressure-sensitive paint

Dynamic stall on a pitching OA209 airfoil in a wind tunnel is investigated at Mach 0.3 and 0.5 using high-speed pressure-sensitive paint (PSP) and pressure measurements. At Mach 0.3, the dynamic stall vortex was observed to propagate faster at the airfoil midline than at the wind-tunnel wall, resulting in a “bowed” vortex shape. At Mach 0.5, shock-induced stall was observed, with initial separation under the shock foot and subsequent expansion of the separated region upstream, downstream and along the breadth of the airfoil. No dynamic stall vortex could be observed at Mach 0.5. The investigation of flow control by blowing showed the potential advantages of PSP over pressure transducers for a complex three-dimensional flow.     

Aeroelastic interactions and trajectory selection of vortex gusts impinging upon Joukowski airfoils

The dynamically-coupled interactions of vortex gusts encountering a symmetric Joukowski airfoil on linear elastic supports is formulated analytically and evaluated numerically using a time-dependent conformal mapping. The Brown and Michael framework models the unsteady shedding of vorticity from the airfoil into the wake, and the aeroelastic motion of the airfoil is analyzed using quasi-steady, apparent mass, and fully-unsteady aerodynamic models. Special attention is paid to the influences of the strength of the incident vortex and the airfoil natural frequency on the initial upstream placement of a vortex gust that achieves direct impingement. These results are weakly sensitive to the initial vortex position in the limits of either large or small structural natural frequency, and the initial vertical vortex position to achieve impingement changes monotonically with the vortex strength. A comparison of the numerical model with available experimental vortex gust measurements over stationary airfoils highlights the appropriate use of the point-vortex model for inviscid vortex–airfoil interaction problems without significant vortex strength decay, which occurs for predominantly viscous interactions of close vortex–airfoil encounters.     

Low Reynolds unsteady flow simulation around NACA0012 airfoil with active flow control

This research numerically elucidates the effects of suction and blowing on the enhancement of unsteady aerodynamic characteristics of flows and their corresponding impact on stall delay over the well-known NACA0012 airfoil at various angles of attack (\( 12 \le {\text{AOA}} \le 20 \)) under low Reynolds numbers. For this purpose, an in-house solver written in C++ is developed. The numerical code utilizes the Jameson’s cell-centered finite volume numerical method accompanied by a progressive power-law preconditioning approach to suppress the stiffness of the governing equations. Many numerical simulations are performed over the suction-blowing control parameters, namely, the slot location (\( L_{j} \)), suction/blowing amplitudes (\( A_{j} \)), and suction/blowing angle (\( \theta_{j} \)). Most of the analyses are based on the measurements of the unsteady aerodynamic characteristics behaviors (such as lift, drag, moment coefficients, and stall phenomena) over the airfoil. The numerical results confirm that the unsteady behavior of the flow (vortex shedding) is weakened or approximately removed when suction is used, especially near the leading edge. In all of the test cases, the ratio of the average lift coefficient to the average drag coefficient increases with increasing suction and blowing amplitudes, except in the case of perpendicular blowing. Furthermore, the blowing is more sensitive to the blowing angle compared to the suction. From the suction and blowing results, it is concluded that the former has a more positive impact on the lift and drag characteristics, especially in the case of incompressible flow at Low-Reynolds regimes.     

The Multi-point Optimization of Shock Control Bump with Constant-Lift Constraint Enhanced with Suction and Blowing for a Supercritical Airfoil

Both shock control bump (SCB) and suction and blowing are flow control methods used to control the shock wave/boundary layer interaction (SWBLI) in order to reduce the resulting wave drag in transonic flows. A SCB uses a small local surface deformation to reduce the shock-wave strength, while suction decreases the boundary-layer thickness and blowing delays the flow separation. Here a multi-point optimization method under a constant-lift-coefficient constraint is used to find the optimum design of SCB and suction and blowing. These flow control methods are used separately or together on a RAE-2822 supercritical airfoil for a wide range of off-design transonic Mach numbers. The RANS flow equations are solved using Roe’s averages scheme and a gradient-based adjoint algorithm is used to find the optimum location and shape of all devices. It is shown that the simultaneous application of blowing and SCB (hybrid blowing/SCB) improves the average aerodynamic efficiency at off-design conditions by 18.2 % in comparison with the clean airfoil, while this increase is only 16.9 % for the hybrid suction/SCB. We have also studied the SWBLI and how the optimization algorithm makes the flow wave structure and interactions of the shock wave with the boundary layer favorable.     

Experimental estimation of a D-shaped cylinder wake using body-mounted sensors

The effectiveness of a small array of body-mounted sensors, for estimation and eventually feedback flow control of a D-shaped cylinder wake is investigated experimentally. The research is aimed at suppressing unsteady loads resulting from the von-Kármán vortex shedding in the wake of bluff-bodies at a Reynolds number range of 100–1,000. A low-dimensional proper orthogonal decomposition (POD) procedure was applied to the stream-wise and cross-stream velocities in the near wake flow field, with steady-state vortex shedding, obtained using particle image velocimetry (PIV). Data were collected in the unforced condition, which served as a baseline, as well as during influence of forcing within the “lock-in” region. The design of sensor number and placement was based on data from a laminar direct numerical simulation of the Navier-Stokes equations. A linear stochastic estimator (LSE) was employed to map the surface-mounted hot-film sensor signals to the temporal coefficients of the reduced order model of the wake flow field in order to provide accurate yet compact estimates of the low-dimensional states. For a three-sensor configuration, results show that the estimation error of the first two cross-stream modes is within 20–40% of the PIV-generated POD time coefficients. Based on previous investigations, this level of error is acceptable for a moderately robust controller required for feedback flow control.     

A mechanism for mitigation of blade–vortex interaction using leading edge blowing flow control

The interaction of a vortical unsteady flow with structures is often encountered in engineering applications. Such flow structure interactions (FSI) can be responsible for generating significant loads and can have many detrimental structural and acoustic side effects, such as structural fatigue, radiated noise and even catastrophic results. Amongst the different types of FSI, the parallel blade–vortex interaction (BVI) is the most common, often encountered in helicopters and propulsors. In this work, we report on the implementation of leading edge blowing (LEB) active flow control for successfully minimizing the parallel BVI. Our results show reduction of the airfoil vibrations up to 38% based on the root-mean-square of the vibration velocity amplitude. This technique is based on displacing an incident vortex using a jet issued from the leading edge of a sharp airfoil effectively increasing the stand-off distance of the vortex from the body. The effectiveness of the method was experimentally analyzed using time-resolved digital particle image velocimetry (TRDPIV) recorded at an 800 Hz rate, which is sufficient to resolve the spatio-temporal dynamics of the flow field and it was combined with simultaneous accelerometer measurements of the airfoil, which was free to oscillate in a direction perpendicular to the freestream. Analysis of the flow field spectra and a Proper Orthogonal Decomposition (POD) of the TRDPIV data of the temporally resolved planar flow fields indicate that the LEB effectively modified the flow field surrounding the airfoil and increased the convecting vortices stand-off distance for over half of the airfoil chord length. It is shown that LEB also causes a redistribution of the flow field spectral energy over a larger range of frequencies.     

Particle image velocimetry investigation of flow over unsteady airfoil with trailing-edge strip

The flow over a flapped NACA 0012 airfoil, oscillated slightly through the static-stall angle, was investigated by using particle image velocimetry, and was supplemented by surface pressure and dynamic-load measurements. A significant increase in the dynamic lift force and nose-down pitching moment was observed. The most pronounced flow phenomenon was the formation and detachment of an energetic leading-edge vortex compared to the no-flapped airfoil. The details of the underlying physical mechanisms responsible for the various light-stall flow processes were provided via the instantaneous velocity and vorticity fields measurements. In contrast to the Gurney flap, the inverted trailing-edge strip led to an improved negative damping while a reduced lift force. The addition of an inverted strip always led to the appearance of a Karman-type vortex shedding street immediately downstream of the strip over the entire oscillation cycle.     

多喷口高效能厚翼的研究

提出了以下高效能翼型的思想：用多喷口小速度切向吹气控制厚翼上的流动分离,使流动接近于理想流状况,以产生大升力,小阻力;因多喷口小速度吹气耗能小,故翼型的有效升阻比可以很大．基于雷诺平均N－S方程进行了数值模拟实验．主要结果表明：对于厚度为0.4的儒氏翼型,在升力系数高达3．5时,有效升阻比可达约50（单喷口吹气约为23）;对于厚度为0．4的"升力体"翼型,在升力系数达2．2时,有效升阻比可达40（喷口吹气约为10）．     

流向振荡柱体尾流控制研究进展

详细介绍了近几年采用尾部喷射、隔离板和小窄条控制件等3 种方法对流向振荡柱体绕流旋涡脱落的抑制情况. 在研究范围内存在非锁频和3种锁频旋涡脱落模式. 风洞实验表明, 尾部喷射对这4 种模式都有抑制效果,窄条控制件对非锁频和2种锁频模式具有抑制效果, 而隔离板仅对非锁频和1 种锁频模式有效. 在不同流动和振荡条件下找出了每种方法的有效控制区, 研究了减阻和减少脉动力的效果, 并探讨了控制机理.