单搭拉剪胶焊接头的应力和刚度分析

胶焊复合连接技术兼具胶接和点焊的优点,它因提高结构强度和刚度而使车辆轻量化成为可能.以胶接理论为基础,考虑了被粘体剪切应变,将焊点视为大剪切弹性模量胶粘剂,胶层和焊点沿其厚度方向的剪应力不变,建立了胶焊单搭拉剪接头的线弹性应力解析模型.在应力模型基础上,将接头各组成部分看作是独立承载的拉伸和剪切弹簧单元,得到了其刚度解析模型.应力模型中的正应力和剪应力与有限元解吻合得较好,证明理论模型正确,参数研究中确定了影响胶焊单搭接头应力分布特征的关键耦合参数.     

单搭接胶接接头拉伸剪切性能的数值模拟与实验研究

采用数值模拟和光测技术对单向拉伸载荷作用下单搭接胶接接头中的剪切性能进行分析,研究了不同厚度胶层中切应力的变化规律。用有限元方法(FEM)对不同胶层厚度的试件进行建模,得到了拉伸载荷下胶粘剂中的切应力分布及其统计参数。利用数字图像相关(digitalimage correlation,DIC)方法对试件的变形场进行测量。结果表明,当胶粘剂的厚度较小时,胶粘剂中的切应力的分布统计参数随着其厚度的增加会有显著的变化,但是当厚度超过一定的数值时,统计参数对厚度的变化不再敏感。     

开孔复合材料层合板强度不确定性分析

以拉伸载荷作用下AS4/3501-6开孔复合材料层合板为研究对象，采用考虑复合材料层合板就地强度效应的有限断裂力学模型和基于方差的敏感性测度分析模型相结合的方法，研究单层板宏观力学性能不确定性对具有不同孔径和铺层顺序的开孔复合材料层合板破坏强度的影响．研究结果表明：单层板力学性能对开孔板强度影响程度的大小与孔径相关，但敏感性排序与孔径无关．同时，单层板力学性能敏感性测度与层合板铺层顺序有关，层合板各向异性比越大，开孔板拉伸破坏受单层板纤维方向拉伸强度的影响越大，而且开孔板拉伸强度与单层板纤维方向拉伸强度呈正相关，与横向弹性模量呈负相关，与面内剪切模量和纵向弹性模量不具有单调关系．     

金属损伤复合材料胶接修补结构力学试验研究

为评估金属损伤复合材料胶接修补结构的剩余强度和剩余寿命,进行了含腐蚀和疲劳损伤LY12CZ航空铝合金板碳/环氧复合材料补片胶接修复结构的力学性能试验,分析了在静拉伸和疲劳载荷作用下修补结构的破坏模式、失效机理。试验研究发现:复合材料胶接修补技术有效改善了腐蚀和疲劳损伤这两类损伤区域的受力状况,恢复了其载荷传递路线,其静拉伸失效形式为金属韧性断裂后胶层脱粘的分步渐进式破坏;与含损伤未修补试样相比,胶接修补大幅度提高了试件的剩余强度和剩余寿命恢复率,修补后铝合金试件承载能力增加了约25%,疲劳寿命增加至修补前的约4倍~5倍。     

含铺层拼接层合板的剪切强度

对含铺层拼接的碳纤维增强树脂基复合材料层合板进行了剪切强度实验研究.从三种不同铺层拼接角层合板上切取含缺口的剪切试件,通过实验测定了其载荷-位移曲线,得到了剪切强度值.实验结果表明,三组试件的剪切强度基本相同,即拼接层角度改变几乎不会引起层合板的剪切强度发生明显变化.采用有限元软件ABAQUS6.5对实验过程进行模拟,得到拼接层角度改变将引起拼接层中0°层出现切应力集中,但沿缺口切应力的平均值几乎不变.这也说明拼接层角度的变化几乎不影响层合板的剪切强度.     

复合材料层板损伤后刚度衰退的实验研究

对复合材料单向板进行了0°、90°、45°拉伸实验,对铺层为[0°/90°]、[±45°]的层合板进行了拉伸实验,对玻璃纤维、碳纤维、芳纶纤维缠绕的NOL环试样分别进行了短梁剪切实验。实验结果表明:碳纤维/环氧树脂基体复合材料单向板没有明显的非线性行为,而层合板在树脂开裂、面内及层间剪切破坏导致的刚度降低却很明显。层间剪切破坏不仅导致剪切刚度的降低,还会引起弯曲刚度的降低。玻璃纤维、芳纶纤维增强树脂基复合材料在三点弯曲实验过程中体现了较强的抗损伤能力,韧性较好;而碳纤维增强树脂基复合材料抗层间损伤能力较差。本文用标准实验方法,跟踪载荷-变形曲线,得到了用于应力分析的刚度衰减系数。用最大应力准则及实验得到的刚度衰减系数,对直径为1400mm的纤维缠绕壳体进行了变形分析,计算结果与实验值一致性较好。     

CFRP复合材料构件胶接特性及失效规律研究

对不同铺层方式和不同胶层厚度的复合材料胶接单搭结构(SLJs)的连接性能进行了研究。使用内聚力模型模拟了SLJs的胶层退化及失效过程，通过与实验对比验证了数值模型的有效性；基于改进后的三维Hashin失效准则，模拟了复合材料层合板的损伤演化。结果表明：胶层的退化形态及失效规律与胶层粘连的复合材料铺层角度密切相关，当胶层两侧粘连的复合材料铺层角度为0°时，胶层会退化形成椭圆环状；当胶层两侧粘连的复合材料铺层角度为45°或-45°时，胶层会退化形成上下中心对称的水滴状；当胶层两侧粘连的复合材料铺层角度为90°时，胶层会退化成沙漏状。0°铺层与胶层相邻时，结构的极限失效载荷最大，此时复合材料未出现损伤；当90°铺层与胶层相邻，结构的极限失效载荷最小且复合材料出现基体损伤、纤维损伤和分层损伤。胶层厚度在0.05～0.5mm时，复合材料胶接单搭结构的连接性能最好，当胶层厚度大于0.5mm,结构的连接性能会大幅下降。     

湿热环境对挖补修理后复合材料层合板振动特性的影响

通过对湿热环境下阶梯挖补胶接修理后碳纤维/双马树脂(T300/QY8911)层合板振动特性的分析,探究了挖补修理后碳纤维/双马树脂层合板在不同湿热效应下的振动特性。基于Mindlin-Reissner板理论与最小势能变分原理,在考虑湿热效应前提下,推导了正交各向异性复合材料层合板的本构关系及四边简支条件下的自由振动控制方程;其次,利用ABAQUS软件建立了三维黏弹性有限元挖补修理模型,应用Fortran语言将湿热耦合下的应力-应变本构关系编入UMAT二次开发文件中,采用三维八节点五自由度等参单元进行了离散。通过与参考文献对照,验证了胶接修理后T300/QY8911层合板有限元模型和编译的湿热环境下UMAT子程序的合理性与有效性。算例结果表明:湿热环境对挖补修理后层合板固有频率的影响比对完整层合板严重;温度对材料性能的影响大于湿度;相比于材料性能变化对振动特性的影响,湿热残余应力对胶接修理后层合板振动特性的影响占主导;参考环境下,胶接修理后层合板的固有频率增大;湿应力对层合板固有频率的影响大于热应力。     

含切口损伤复合材料层合板拉伸失效行为研究

对含有不同切口损伤的复合材料层合板试件进行了拉伸试验,采用电阻应变计同步测量切口损伤前缘区域随载荷的变化,测定含切口损伤层合板的剩余强度,并讨论了损伤长度和损伤角度对剩余强度的影响规律。建立含切口损伤复合材料层合板有限元模型,分析了含切口损伤复合材料层合板的拉伸失效行为,计算了含切口损伤复合材料层合板的剩余强度,确定了剩余强度与切口损伤状态的关系。计算结果与试验结果具有较好的一致性。     

非对称铺层复合材料层合板质量优化设计

复合材料广泛应用于航空航天等领域,追求轻量化设计已经成为研究重点。对复合材料层合板质量优化设计,可以减少层合板的纤维用量,减小层合板的质量,降低成本。首先研究复合材料层合板在承受轴向载荷时,产生的形变量、应力示意图,分析容易发生失效部位;以层合板铺层厚度为设计变量,最大应变、铺层比例等为约束条件,最小化层合板质量为优化目标,对碳纤维复合材料层合板铺层厚度等设计变量进行优化,利用强度理论对优化结果进行校核,结合力学试验对比分析优化前后层合板力学性能。结果表明:碳纤维复合材料层合板经过优化后,总质量减轻约16.7%,优化后的层合板满足复合材料强度理论,实验结果与软件仿真具有一致性,说明优化方法是合理可靠的。     

FRP-混凝土界面粘结行为的参数影响研究

FRP-混凝土界面的粘结性能对FRP加固混凝土结构力学行为和破坏模式有着重要影响。本文对表征FRP-混凝土界面粘结性能的三个重要参数(界面初始刚度、最大剪应力、界面破坏能)开展研究,通过13个单剪试件的试验考察了混凝土强度、胶层厚度和粘结长度等因素对界面粘结行为的影响,根据试验结果拟合了界面破坏能、最大剪切应力与胶层剪切刚度、混凝土强度之间的函数关系。在试验研究基础上,构建了外贴FRP-混凝土界面粘结的有限元模型。通过有限元分析考察了界面破坏能等三个参数不变的前提下,不同的局部粘结滑移本构关系对界面粘结行为的影响;进而研究了其中一个参数变化时引起的界面粘结性能改变。研究结果表明:界面粘结承载力随着胶层厚度增加而逐渐提高;胶层厚度与界面破坏能成正比,与峰值剪应力成反比;当界面破坏能等三个参数保持不变时,局部粘结滑移本构关系对FRP-混凝土界面粘结性能的影响较小;三个参数中的一个增大时将延缓界面破坏的过程。     

Stress analyses of a smart composite pipe joint integrated with piezoelectric composite layers under torsion loading

In order to improve the joint failure strength, an adhesively bonded smart composite pipe joint system has been developed by integrating electromechanical coupling piezoelectric layers with the connection coupler. It has been validated that the integrated piezoelectric ceramic layers can smartly reduce stress concentration in the adhesive layer bond-line under bending or axial tension loads. In this study, piezoelectric particle/fiber reinforced polymer composite was utilized to construct adhesively bonded smart composite pipe joint systems, in order to overcome the brittle characteristic of the piezoelectric ceramic layers and to facilitate joint construction. Since torsion is one of the dominating loading conditions in practice, the behavior of the newly developed smart pipe joint system subjected to torsion loading was investigated in-detail to evaluate the effect of the integrated piezoelectric reinforced polymer composite layer on the joint performance. Firstly, based on the first-order shear deformation theory, the fundamental equations with relevant boundary and continuity conditions were developed to theoretically model the smart pipe joint system subjected to torsion loading. Further, the analytical solutions for the mid-plane displacements and the shear and peel stresses in the adhesive layer were obtained by using the Levy solution and the state-space method. Finally, some numerical examples were presented to evaluate the detailed effect of the stacking sequence and thickness of the integrated composite piezoelectric layers in the connection coupler on reducing the stress concentration in the adhesive layer; the effect of the applied electric fields on shear and peel stresses in the adhesive layer was also illustrated.     

CFRP-混凝土界面粘结的疲劳性能试验研究

外贴FRP是重要的混凝土结构加固技术,但目前对外贴FRP加固混凝土结构的疲劳性能研究尚不充分,尤其对FRP-混凝土粘结界面的疲劳退化规律和破坏模式的研究更为缺乏。本文采用双面剪切试件,通过2个静载试件和4个疲劳试件的试验研究,考察了粘结长度和胶层厚度等因素对FRP-混凝土界面粘结疲劳性能的影响。通过分析沿粘结长度的FRP应变分布在疲劳循环过程中和疲劳后静载过程中的变化情况,讨论了不同粘结长度和粘结胶层厚度条件下的粘结界面疲劳退化规律和疲劳后静载性能。试验结果表明:胶层树脂-混凝土粘结界面是发生疲劳剥离破坏的薄弱环节;胶层厚度增大时,由于疲劳引起的界面损伤累积发展显著减小,疲劳后静载中胶层厚度较大试件的粘结承载力也更大;粘结长度增大时,界面粘结呈现更为明显的损伤退化,但由于试验粘结长度小于有效粘结长度,疲劳后的静粘结承载力仍更大。     

Finite Fracture Mechanics model for mixed mode fracture in adhesive joints

Up to now the failure load assessment of bonded joints is still not fully understood. This work provides a new approach for assessing the crack initiation load of bonded joints. A failure model for single lap joints is proposed that is based on Finite Fracture Mechanics. Only two basic fracture parameters are required: the tensile strength and the fracture toughness of the adhesive. A coupled stress and energy criterion proposed in 2002 by Leguillon is used to model crack initiation in the adhesive layer. The theory of this criterion is outlined in detail, its relationship to other failure criteria is discussed and an overview of applications found in literature is given. An enhanced weak interface model that predicts a linear variation of the shear stresses in the adhesive layer is utilized to model the single lap joint. To compare joint designs and to reveal the limitations of the given approach a dimensionless brittleness number for mixed-mode loading is proposed. Along with a detailed discussion of the results for exemplary joint designs a comparison to experimental results from literature is performed. The two necessary fracture parameters are each taken from standard test results published in literature. A good agreement of the failure load predictions with the experimental results is observed. A remarkable outcome is that the presented failure model renders the adhesive thickness effect correctly. The paper concludes with a discussion of the limitations of the approach and the effect of material parameters.     

Dynamic tensile strength of composite laminate joints fastened mechanically

The tensile strength of composite joints is determined under dynamic loading conditions. The composites are laminates made from hybrid fiber reinforced plastic (HFRP) and carbon fiber reinforced plastic (CFRP). Three different mechanically fastened joint configurations are considered: they are the pin-connected, single-lap and double-lap type. The joint strength under dynamic load is found to be lower than that under quasi-static load. The pin-connected joint was the weakest. Investigated also are the influence of geometric parameters for pin-connected HFRP laminate joints. The results shed light on how to improve the bearing strength of mechanical joints when encountering dynamic loads.     

A three-parameter elastic foundation model for interface stresses in curved beams externally strengthened by a thin FRP plate

Externally bonding of fiber reinforced polymer (FRP) plates or sheets has become a popular method for strengthening reinforced concrete structures. Stresses along the FRP–concrete interface are of great importance to the effectiveness of this type of strengthening because high stress concentration along the FRP–concrete interface can lead to the FRP debonding from the concrete beam. In this study, we develop an analytical solution of interface stresses in a curved structural beam bonded with a thin plate. A novel three-parameter elastic foundation model is used to describe the behavior of the adhesive layer. This adhesive layer model is an extension of the two-parameter elastic foundation commonly used in existing studies. It assumes that the shear stress in the adhesive layer is constant through the thickness, and the interface normal stresses along two concrete/adhesive and adhesive/FRP interfaces are different. Closed-form solutions are obtained for these two interfacial normal stresses, shear stress within the adhesive layer, and beam forces. The validation of these solutions is confirmed by finite element analysis.     

升温条件下偏高岭土基地质聚合物粘结剂的粘结性能研究

结构加固中应用的环氧树脂等有机粘结剂的耐高温性不足,升温条件下易丧失力学性能导致结构失效。本文以偏高岭土基地聚物作为无机粘结剂,通过不同温度下的钢-钢拉伸剪切试验和表层嵌贴CFRP-混凝土拔出试验,考察地聚物粘结剂在升温条件下的粘结性能变化规律。试验结果表明:在常温环境下,树脂粘结剂的粘结性能优于地质聚合物粘结剂的粘结性能;但在本文试验设置的升温条件下,树脂粘结剂试件的粘结承载力明显下降,而地质聚合物粘结剂试件的粘结承载力则基本不受温度变化的影响。对粘结界面的粘结滑移本构关系的分析表明,随着温度升高,树脂粘结剂的最大粘结应力逐渐降低,其对应的滑移量也有所增大;与之相比,地聚物粘结剂的最大粘结应力及滑移均未随温度升高发生显著变化,证明了地聚物粘结剂的粘结性能对本文试验温度不敏感。这表明地质聚合物具有较好的耐高温性能,有发展无机粘结剂的潜力。     

FRP加固梁的FRP-混凝土界面脱胶分析

为了研究纤维增强聚合物(fiber reinforced polymer, FRP) 加固梁的FRP-混凝土界面脱胶破坏过程,本文将混凝土梁和FRP 板均视为线弹性的欧拉-伯努利梁(Euler-Bernoulli beams), 且两者通过粘结层胶结在一起. 对于FRP-混凝土结构,有两种形式的脱胶破坏：板端脱胶破坏和跨中裂缝导致的脱胶破坏.对于FRP-混凝土梁,利用合理的粘结模型按第2 种脱胶失效形式,详细讨论了FRP-混凝土界面的脱胶过程,得到了不同阶段的胶结滑移、界面剪应力和FRP 轴向力的解析解. 实验研究验证了理论分析的结果,参数研究进一步探讨了胶结长度和粘结层厚度对于FRP-混凝土界面脱胶行为的影响.     

Design and analysis of a smart composite pipe joint system integrated with piezoelectric layers under bending

Incorporating with the high electro-mechanical coupling performance of piezoelectric materials, design and analysis of an adhesively bonded smart composite pipe joint system were conducted. In this joint system, piezoelectric layers were integrated into the joint coupler in order to reduce stress concentration in the joint adhesive layer. To theoretically verify the composite action and efficiency of the integrated piezoelectric layers, an electro-mechanical model based on the first-order shear deformation theory was established. This model was able to clarify the energetic characteristics of the proposed joint system on the improvement in the joint strength, which was under the action of a bending moment at the joint ends. The state-space method was utilized to obtain the final analytical solutions, including the peel and shear stress distributions in the adhesive layer. Finally, some numerical examples were calculated to evaluate the effect of the detailed stacking sequence and size of the integrated piezoelectric layers on reducing the stress concentration in the adhesive layer as well as the applied electric fields. These numerical results validated the integrity of the developed adhesively bonded smart composite pipe joint system.