The mirror relations and nonlinear viscoelasticity of polymer melts

An attempt is made to incorporate into a quasilinear viscoelastic constitutive equation of the Boltzmann superposition type the two mirror relations of Gleissle, as well as his relation between the steady-state first normal-stress difference and the shear viscosity curve. It is shown that the three relations can hold separately within this constitutive model, but not simultaneously, because they require a different nonlinear strain measure, namelyS ₁₂ () = – a ( – 1) (a = 0 for 1,a = 1 for 1) for the mirroring of the viscosities,S ₁₂ () = – a (–k ²/) (a = 0 for k, a = 1 for k) for the mirroring of the first normal-stress coefficients, and for the third relation. Here denotes the shear strain and erf the error function. Experimental data on melts of a low-density polyethylene, a high-density polyethylene and a polypropylene show that the mirror relations are passable approximations, but that the third relation meets reality surprisingly close if the right value ofk is used.     

Pulsatile flow in a tube with wall injection and suction

This paper studies similarity solutions for pulsatile flow in a tube with wall injection and suction. The Navier-Stokes equations are reduced to a system of three ordinary differential equations. Two of the equations represent the effects of suction and injection on the steady flow while the third represents the effects of suction and injection on pulsatile flow. Since the equations for steady flow have been studied previously, the analysis centers on the third equation. This equation is solved numerically and by the method of matched asymptotic expansions. The exact numerical solutions compare well with the asymptotic solutions.The effects of suction and injection on pulsatile flow are the following: a) Small values of suction can cause a resonance-like effect for low frequency pulsatile flow. b) The annular effect still occurs but for large injection or suction the frequency at which this effect becomes dominant depends on the cross-flow Reynolds number. c) The maximum shear stress at the wall is decreased by injection, but may be increased or decreased by suction.Nomenclature a radius of the tube - a ₀ ² i ² - A₀, B₀, C₀, D₀, E₀ constant coefficients appearing in the expression for pressure - b a non-dimensionalized length - b ₀ ² i ^{2 2} - b _k complex coefficients of a power series - B - C ₁, C ₂, D complex constants - d - D _1,2 - f() F(a ^1/2)/aV - f ₀,f ₁,... functions of order one used in asymptotic expansions of f() - F(r) rv _r - g() - G(r) a steady component of velocity in axial direction - h() 4/C₀ a ² H(a ^1/2) - h ₀,h ₁,h ₂,...;l ₀,l ₁,l ₂,... functions of order one used in asymptotic expansions for h() in outer regions - H(r) complex valued function giving unsteady component of velocity - H ₀, H ₁, H ₂, ... K ₀, K ₁, K ₂, ...; L ₀, L ₁, L ₂, ... functions of order one used in asymptotic expansions for h() in inner regions - i - J ₀, J ₁, Y ₀, Y ₁ Bessel functions of first and second kind - k - K Rk/2b ² - O order symbol - p pressure - p ₁(z, t) arbitrary function related to pressure - r radial coordinate - r ₀ (1+16 ^{4 4})^1/4 - R Va/, the crossflow Reynolds number - t time - u() G(r)/V - v _r radial velocity - v _z axial velocity - V constant velocity at which fluid is injected or extracted - z axial coordinate - ² a ²/4 - 4.196 - small parameter; =–2/R (Sect. 4); =–R/2 (Sect. 5); =2/R(Sect. 6) - r ²/a ² - * 0.262 - Arctan (4 ^{2 2}) - , inner variables - kinematic viscosity - b - * zero of g() - density - (r, t) arbitrary function related to axial velocity - frequency     

Effect of measuring volume length on two-component laser velocimeter measurements in a turbulent boundary layer

The effects of finite measuring volume length on laser velocimetry measurements of turbulent boundary layers were studied. Four different effective measuring volume lengths, ranging in spanwise extent from 7 to 44 viscous units, were used in a low Reynolds number (Re=1440) turbulent boundary layer with high data density. Reynolds shear stress profiles in the near-wall region show that u v strongly depends on the measuring volume length; at a given y-position, u v decreases with increasing measuring volume length. This dependence was attributed to simultaneous validations on the U and V channels of Doppler bursts coming from different particles within the measuring volume. Moments of the streamwise velocity showed a slight dependence on measuring volume length, indicating that spatial averaging effects well known for hot-films and hot-wires can occur in laser velocimetry measurements when the data density is high.List of symbols time-averaged quantity - u wall friction velocity, ( _w /)^1/2 - v kinematic viscosity - d _p pinhole diameter - l _eff spanwise extent of LDV measuring volume viewed by photomultiplier - l ⁺ non-dimensional length of measuring volume, l _eff u /v - y ⁺ non-dimensional coordinate in spanwise direction, y u /v - z ⁺ non-dimensional coordinate in spanwise direction, z u /v - U ⁺ non-dimensional mean velocity, /u - u instantaneous streamwise velocity fluctuation, U &#x2329;U - v instantaneous normal velocity fluctuation, V–V - u RMS streamwise velocity fluctuation, u ^21/2 - v RMS normal velocity fluctuation, v ^21/2 - Re Reynolds number based on momentum thickness, U 0/v - R _uv cross-correlation coefficient, u v/u v - R₁₂(0, 0, z) two point correlation between u and v with z-separation, <u(0, 0, 0) v (0, 0, z)>/<u(0, 0, 0) v (0, 0, 0)> - N rate at which bursts are validated by counter processor - T Taylor time microscale, u (dv/dt²)^–1/2     

Transport in ordered and disordered porous media IV: Computer generated porous media for three-dimensional systems

In the method of volume averaging, the difference between ordered and disordered porous media appears at two distinct points in the analysis, i.e. in the process of spatial smoothing and in the closure problem. In theclosure problem, the use of spatially periodic boundary conditions isconsistent with ordered porous media and the fields under consideration when the length-scale constraint,r ₀L is satisfied. For disordered porous media, spatially periodic boundary conditions are an approximation in need of further study.In theprocess of spatial smoothing, average quantities must be removed from area and volume integrals in order to extractlocal transport equations fromnonlocal equations. This leads to a series of geometrical integrals that need to be evaluated. In Part II we indicated that these integrals were constants for ordered porous media provided that the weighting function used in the averaging process contained thecellular average. We also indicated that these integrals were constrained by certain order of magnitude estimates for disordered porous media. In this paper we verify these characteristics of the geometrical integrals, and we examine their values for pseudo-periodic and uniformly random systems through the use of computer generated porous media.

Nomenclature

Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - a _i i=1, 2, 3 gaussian probability distribution used to locate the position of particles - I unit tensor - L general characteristic length for volume averaged quantities, m - L characteristic length for , m - L characteristic length for , m - characteristic length for the -phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1, 2, 3 lattice vectors, m - m convolution product weighting function - m _v special convolution product weighting function associated with the traditional volume average - n _i i=1, 2, 3 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - r position vector, m - r _m support of the weighting functionm, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume,, m³ - x positional vector locating the centroid of an averaging volume, m - x ₀ reference position vector associated with the centroid of an averaging volume, m - y position vector locating points relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - /L, small parameter in the method of spatial homogenization - standard deviation ofa _i - _r standard deviation ofr - _r intrinsic phase average of      

Flow in porous media III: Deformable media

Stokes flow in a deformable medium is considered in terms of an isotropic, linearly elastic solid matrix. The analysis is restricted to steady forms of the momentum equations and small deformation of the solid phase. Darcy's law can be used to determine the motion of the fluid phase; however, the determination of the Darcy's law permeability tensor represents part of the closure problem in which the position of the fluid-solid interface must be determined.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A ^* interfacial area of the- interface contained within a unit cell, m² - A _e ^* area of entrances and exits for the-phase contained within a unit cell, m² - E Young's modulus for the-phase, N/m² - e i unit base vectors (i = 1, 2, 3) - g gravity vector, m²/s - H height of elastic, porous bed, m - k unit base vector (=e ₃) - characteristic length scale for the-phase, m - L characteristic length scale for volume-averaged quantities, m - n unit normal vector pointing from the-phase toward the-phase (n = -n ) - p pressure in the-phase, N/m² - P p – g·r, N/m² - r ₀ radius of the averaging volume, m - r position vector, m - t time, s - T total stress tensor in the-phase, N/m² - T ⁰ hydrostatic stress tensor for the-phase, N/m² - u displacement vector for the-phase, m - V averaging volume, m₃ - V volume of the-phase contained within the averaging volume, m³ - v velocity vector for the-phase, m/s Greek Letters V /V, volume fraction of the-phase - mass density of the-phase, kg/m³ - shear coefficient of viscosity for the-phase, Nt/m² - first Lamé coefficient for the-phase, N/m² - second Lamé coefficient for the-phase, N/m² - bulk coefficient of viscosity for the-phase, Nt/m² - T –T ⁰ , a deviatoric stress tensor for the-phase, N/m²     

Experimental investigation of the creeping motion of a drop in a vertical tube

New experimental data regarding the motion of a drop along the axis of a vertical tube, filled with another highly viscous liquid, are obtained. The experiments are realised with sufficiently large drops for an internal circulation to develop and also for different pairs of fluids; the preponderant role of the gravity on the drop shape and consequently on its terminal velocity is pointed out. Moreover, by means of a visualization technique, details on the flow both inside and outside the drop are given.List of symbols g gravity acceleration - r distance from the drop center - R equivalent radius of the drop, i.e. the radius of the sphere having the same volume as the drop - R _EQ radius of the equatorial section of the drop - R _T tube radius - L _AX half length of the drop - U ₀ terminal velocity of the drop - P _s Poiseuille number= U _{0 e} /4 g R ² - Fr Fronde number = U ₀ ² _e /2 g R - Re Reynolds number = 2 U ₀ R _e / _e - E _o Eötvös number = 4g R ²/ - deformation parameter = _e U ₀/ - apparent density of the suspended liquid= | _i – _e | - _i viscosity of the suspended liquid - _e viscosity of the suspending liquid - drop-to-tube radius ratio = R/R _T - _EQ equatorial drop-to-tube radius ratio = R EQ/R _T - interfacial tension     

The very slow flow of a Powell-Eyring fluid around a sphere

Summary The very slow flow of a Powell-Eyring type non-Newtonian fluid around a sphere is investigated by a variational technique. The result, a correction factor that is applied to the Stokes' equation, is given as a plot and as an equation which is empirically fit to the plot. Also, a comparison of the very slow flows of a simplified viscoelastic Oldroyd fluid and the Powell-Eyring fluid is made which indicates that in a certain restricted region of the very slow flows, both models give essentially the same results. The Oldroyd and Powell-Eyring model parameters are interrelated by forcing both models to fit the same tube flow viscosity data.Nomenclature B dimensionless quantity, v /R - C dimensionless second invariant - c ₁ constant determined by variational method - D dimensionless variational integral - D _2j , D _j+k position-independent variables used in specification of trial functions - E _2j , E _j+k position-independent variables used in specification of trial functions - f friction factor - f _corr friction factor correction - F _drag drag force on sphere - g, g ₀, g ₁ general trial function; first and second terms in the general trial function - G, H terms in the expression for C - j index - J variational integral - k index - K term in the expression for C - p, q integers - r integer, radial coordinate - R radius of sphere - Re Reynolds number - Re ₀ Reynolds number at point of zero shear rate - Re Reynolds number at infinite distance from sphere - Re _NN Reynolds number based on variable part of viscosity - u, v dimensionless position coordinates - V volume considered - v _i ith velocity component - v _r , v , v _z velocity components in the r, , and z-directions - v approach velocity of the fluid - x/ parameter in Powell-Eyring model - x _i i-position coordinate - parameter in Powell-Eyring model - rate of deformation - , _c , _N , ₀ coefficient of viscosity; cross viscosity; parameter in Powell-Eyring model; viscosity in limit of zero shear rate - spherical coordinate - , _ij rate of deformation tensor; ij-component of rate of deformation tensor - ₁, ₂ parameters in Oldroyd model - Newtonian viscosity - ₁, ₂ parameters in Oldroyd model - dimensionless radial coordinate, r/R - second invariant - fluid density - spherical coordinate - stream function     

An exact solution for non-darcy free convection from a horizontal line source of heat

In this paper we consider the free convection from a horizontal line source of heat which is embedded in an unbounded porous medium saturated with a fluid at rest under gravity. The convective fluid and the porous medium are in local thermal equilibrium.

---

Eine exakte Lösung der nicht-darcy'schen freien Konvektion von einer horizontalen, linienförmigen Wärmequelle

Zusammenfassung In dem Aufsatz wird die freie Konvektion von einer horizontalen, linienförmigen Wärmequelle untersucht, die in ein unbegrenztes poröses Medium eingebettet ist. Die Poren des porösen Mediums sind mit einem Fluid gefüllt, das unter Schwerkrafteinfluß ruht. Das strömende Fluid und das poröse Medium sind örtlich im thermischen Gleichgewicht.

---

Nomenclature c _p specific heat of convective fluid - F _o parameter,=/(vl>g - g acceleration due to gravity - k thermal conductivity of the saturated porous medium - l typical length scale of body - Q heat flux per unit length of a line source - Ra Rayleigh number, =gQl/²c_p - Ra _x local Rayleigh number, =xg Qx/ a²c_p - T temperature - T temperature of ambient fluid - u, x andy components of velocity - x, y coordinates vertically upwards and normal to axis of plume - X, Y non-dimensional coordinates vertically upwards and normal to axis of plume Greek symbols equivalent themal diffusivity - coefficient of thermal expansion - similarity variable - non-dimensional temperature - x permeability of porous medium - viscosity of convective fluid - v kinematic viscosity of convective fluid - density of convective fluid - stream function - non-dimensional stream function - the Forchheimer's coefficient     

Transport in ordered and disordered porous media III: Closure and comparison between theory and experiment

In this paper we examine the closure problem associated with the volume averaged form of the Stokes equations presented in Part II. For both ordered and disordered porous media, we make use of a spatially periodic model of a porous medium. Under these circumstances the closure problem, in terms of theclosure variables, is independent of the weighting functions used in the spatial smoothing process. Comparison between theory and experiment suggests that the geometrical characteristics of the unit cell dominate the calculated value of the Darcy's law permeability tensor, whereas the periodic conditions required for thelocal form of the closure problem play only a minor role.Roman Letters A interfacial area of the- interface contained within the macroscopic region, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface associated with the local closure problem, m² - A _p surface area of a particle, m² - b vector used to represent the pressure deviation, m^–1 - B ⁰ B+I, a second order tensor that maps v _m ontov - B second-order tensor used to represent the velocity deviation - d _p 6V _p/A_p, effective particle diameter, m - d a vector related to the pressure, m - D a second-order tensor related to the velocity, m² - g gravity vector, m/s² - I unit tensor - K traditional Darcy's law permeability tensor calculated on the basis of a spatially periodic model, m² - K _m permeability tensor for the weighted average form of Darcy's law, m² - L general characteristic length for volume averaged quantities, m - L _p characteristic length for the volume averaged pressure, m - L characteristic length for the porosity, m - L _v characteristic length for the volume averaged velocity, m - characteristic length (pore scale) for the-phase - _i i=1, 2, 3 lattice vectors, m - weighting function - m(-y) , convolution product weighting function - m _v special convolution product weighting function associated with the traditional averaging volume - m _g general convolution product weighting function - m _V unit cell convolution product weighting function - m _C special convolution product weighting function for ordered media which produces the cellular average - n unit normal vector pointing from the-phase toward the -phase - p pressure in the-phase, N/m² - p _m superficial weighted average pressure, N/m² - p _m intrinsic weighted average pressure, N/m² - p traditional intrinsic volume averaged pressure, N/m² - p – p _m , spatial deviation pressure, N/m² - r ₀ radius of a spherical averaging volume, m - r _m support of the convolution product weighting function - r position vector, m - r position vector locating points in the-phase, m. - V averaging volume, m³ - B volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - v velocity vector in the-phase, m/s - v _m superficial weighted average velocity, m/s - v _m intrinsic weighted average velocity, m/s - v traditional superficial volume averaged velocity, m/s - v – v _m , spatial deviation velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the -phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - _m m * , weighted average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m²     

Flow birefringence of polymer melts: Application to the investigation of time dependent rheological properties

Summary Transient stresses including normal stresses, which are developed in a polymer melt by a suddenly imposed constant rate of shear, are investigated by mechanical measurement and, indirectly, with the aid of the flow birefringence technique. For the latter purpose use is made of the so-called stress-optical law, which is carefully checked.It appears that the essentially linear model of the rubberlike liquid, as proposed byLodge, is capable of describing the behaviour of polymer melts rather well, if the applied total shear does not exceed unity. In order to describe also steady state values of the stresses successfully, one should extend measurements to extremely low shear rates.These statements are verified with the aid of a method which was originally designed bySchwarzl andStruik for the practical calculation of interrelations between linear viscoelastic functions. In the present paper dynamic shear moduli are used as reference functions.

---

Zusammenfassung Mit der Zeit anwachsende Spannungen, darunter auch Normalspannungen, wie sie sich nach dem plötzlichen Anlegen einer konstanten Schergeschwindigkeit in einer Polymerschmelze entwickeln, werden mit Hilfe mechanischer Messungen und indirekt mit Hilfe der Strömungsdoppelbrechung untersucht. Für den letzteren Zweck wird das sogenannte spannungsoptische Gesetz herangezogen, dessen Gültigkeit sorgfältig überprüft wird.Es ergibt sich, daß das im Wesen lineare Modell der gummiartigen Flüssigkeit, wie es vonLodge vorgeschlagen wurde, sich recht gut zur Beschreibung des Verhaltens von Polymerschmelzen eignet, solange der im ganzen angelegte Schub den Wert Eins nicht überschreitet. Um auch stationäre Werte der Spannungen in die Beschreibung erfolgreich einzubeziehen, sollte man die Messungen bis zu extrem niedrigen Schergeschwindigkeiten ausdehnen.Die gemachten Feststellungen werden mit Hilfe einer Methode verifiziert, die vonSchwarzl undStruik ursprünglich für die praktische Berechnung von Beziehungen zwischen Zustandsfunktionen entwickelt wurde, die dem linear viskoelastischen Verhalten entsprechen. In der vorliegenden Veröffentlichung dienen die dynamischen Schubmoduln als Bezugsfunktionen.

---

a _T shift factor - B _ij Finger deformation tensor - C stress-optical coefficient, (m²/N) - f (p _jl ) undetermined scalar function - G shear modulus, (N/m²) - G(t) time dependent shear modulus, (N/m²) - G() shear storage modulus, (N/m²) - G() shear loss modulus, (N/m²) - G _r reduced shear storage modulus, (N/m²) - G _r reduced shear loss modulus, (N/m²) - H() shear relaxation time spectrum, (N/m²) - k Boltzmann constant, (Nm/°K) - n _ik refractive index tensor - p undetermined hydrostatic pressure, (N/m²) - p _ij ,p _ik stress tensor, (N/m²) - p ₂₁ shear stress, (N/m²) - p ₁₁ –p ₂₂ first normal stress difference, (N/m²) - p ₂₂ –p ₃₃ second normal stress difference, (N/m²) - q shear rate, (s^–1) - t, t time, (s) - T absolute temperature, (°K) - T ₀ reference temperature, (°K) - x the ratiot/ - x position vector of a material point after deformation, (m) - x position vector of a material point before deformation, (m) - ₀, ₁ constants in eq. [37] - ₀, ₁ constants in eq. [37] - shear deformation - (t, t) time dependent shear deformation - _ij unity tensor - n flow birefringence in the 1–2 plane - (q) non-Newtonian shear viscosity, (N s/m²) - ^* () complex dynamic viscosity, (N s/m²) - | ^* ()| absolute value of complex dynamic viscosity, (N s/m²) - () real part of complex dynamic viscosity, (N s/m²) - () imaginary part of complex dynamic viscosity, (N s/m²) - (t — t) memory function, (N/m² · s) - v number of effective chains per unit of volume, (m^–3) - temperature dependent density, (kg/m³) - ₀ density at reference temperatureT ₀, (kg/m³) - relaxation time, (s) - integration variable, (s) - (x) approximate intensity function - ₁ (x) error function - extinction angle - _m orientation angle of the stress ellipsoid - circular frequency, (s^–1) - 1 direction of flow - 2 direction of the velocity gradient - 3 indifferent direction - t time dependence The present investigation has been carried out under the auspices of the Netherlands Organization for the Advancement of Pure Research (Z. W. O.).North Atlantic Treaty Organization Science Post Doctoral Fellow.Research Fellow, Delft University of Technology.With 11 figures and 2 tables     

Heat conduction in a cylinder crossed by an electric current with skin effect

The steady periodic temperature distribution in an infinitely long solid cylinder crossed by an alternating current is evaluated. First, the time dependent and non-uniform power generated per unit volume by Joule effect within the cylinder is determined. Then, the dimensionless temperature distribution is obtained by analytical methods in steady periodic regime. Dimensionless tables which yield the amplitude and the phase of temperature oscillations both on the axis and on the surface of copper or nichrome cylindrical electric resistors are presented.

---

Wärmeleitung in einem stromdurchflossenen Zylinder unter Berücksichtigung des Skin-Effektes

Zusammenfassung Es wird die periodische Temperaturverteilung für den eingeschwungenen Zustand in einem unendlich langen, von Wechselstrom durchflossenen Vollzylinder ermittelt. Zuerst erfolgt die Bestimmung der zeitabhängigen, nichgleichförmigen Energiefreisetzung pro Volumeneinheit des Zylinders infolge Joulescher Wärmeentwicklung und anschließend die Ermittlung der quasistationären Temperaturverteilung auf analytischem Wege. Amplitude und Phasenverzögerung der Temperaturschwingungen werden für die Achse und die Oberfläche eines Kupfer- oder Nickelchromzylinders tabellarisch in dimensionsloser Form mitgeteilt.

---

Nomenclature A integration constant introduced in Eq. (2) - ber, bei Thomson functions of order zero - Bi Biot numberhr ₀/ - c speed of light in empty space - c ₁,c ₂ integration constants introduced in Eq. (46) - c _p specific heat at constant pressure - E electric field - E _z component ofE alongz - E time independent part ofE, defined in Eq. (1) - f function ofs and defined in Eq. (11) - g function ofs and defined in Eq. (37) - h convection heat transfer coefficient - H magnetic field - i imaginary uniti=(–1)^1/2 - I electric current - I _eff effective electric currentI _eff=I/2^1/2 - Im imaginary part of a complex number - J _n Bessel function of first kind and ordern - J electric current density - q _g power generated per unit volume - time average of the power generated per unit volume - time averaged power per unit length - r radial coordinate - R electric resistance per unit length - r ₀ radius of the cylinder - Re real part of a complex number - s dimensionless radial coordinates=r/r ₀ - s, s integration variables - t time - T temperature - time averaged temperature - T _f fluid temperature outside the boundary layer - time average of the surface temperature of the cylinder - u, functions ofs, and defined in Eqs. (47) and (48) - W Wronskian - x position vector - x real variable - Y _n Bessel function of second kind and ordern - z unit vector parallel to the axis of the cylinder - z axial coordinate - · modulus of a complex number - equal by definition Greek symbols amplitude of the dimensionless temperature oscillations - electric permittivity - dimensionless temperature defined in Eq. (16) - ₀, ₁, ₂ functions ofs defined in Eq. (22) - thermal conductivity - dimensionless parameter=(2)^1/2 - magnetic permeability - ₀ magnetic permeability of free space - function of defined in Eq. (59) - dimensionless parameter=c _p/() - mass density - electric conductivity - dimensionless time=t - phase of the dimensionless temperature oscillations - function ofs:= ₁+i ₂ - angular frequency - dimensionless parameter=()^1/2 r ₀     

Approximate solutions for drag coefficient of bubbles moving in shear-thinning elastic fluids

The drag coefficient for bubbles with mobile or immobile interface rising in shear-thinning elastic fluids described by an Ellis or a Carreau model is discussed. Approximate solutions based on linearization of the equations of motion are presented for the highly elastic region of flow. These solutions are in reasonably good agreement with the theoretical predictions based on variational principles and with published experimental data. C _D Drag coefficient - E ^* Differential operator [E ^{* 2} = ²/² + (sin/ ²)/(1/sin /)] - El Ellis number - F _D Drag force - K Consistency index in the power-law model for non-Newtonian fluid - n Flow behaviour index in the Carreau and power-law models - P Dimensionless pressure [=(p – p ₀)/₀ (U /R)] - p Pressure - R Bubble radius - Re ₀ Reynolds number [= 2R U /₀] - Re Reynolds number defined for the power-law fluid [= (2R) ⁿ U ^2–n /K] - r Spherical coordinate - t Time - U Terminal velocity of a bubble - u Velocity - Wi Weissenberg number - Ellis model parameter - Rate of deformation - Apparent viscosity - ₀ Zero shear rate viscosity - Infinite shear rate viscosity - Spherical coordinate - Parameter in the Carreau model - ^* Dimensionless time [=/(U /R)] - Dimensionless length [=r/R] - Second invariant of rate of deformation tensors - ^* Dimensionless second invariant of rate of deformation tensors [=/(U /R)²] - Second invariant of stress tensors - ^* Dimensionless second invariant of second invariant of stress tensor [= / ₀ ² (U /R)²] - Fluid density - Shear stress - ^* Dimensionless shear stress [=/ ₀ (U /R)] - _1/2 Ellis model parameter - ₁ ^2/* Dimensionless Ellis model parameter [= _1/2/ ₀(U /R)] - Stream function - ^* Dimensionless stream function [=/U R ²]     

On the prediction of riblet performance with engineering turbulence models

The paper reports the outcome of a numerical study of fully developed flow through a plane channel composed of ribleted surfaces adopting a two-equation turbulence model to describe turbulent mixing. Three families of riblets have been examined: idealized blade-type, V-groove and a novel U-form that, according to computations, achieves a superior performance to that of the commercial V-groove configuration. The maximum drag reduction attained for any particular geometry is broadly in accord with experiment though this optimum occurs for considerably larger riblet heights than measurements indicate. Further explorations bring out a substantial sensitivity in the level of drag reduction to the channel Reynolds number below values of 15 000 as well as to the thickness of the blade riblet. The latter is in accord with the trends of very recent, independent experimental studies.Possible shortcomings in the model of turbulence are discussed particularly with reference to the absence of any turbulence-driven secondary motions when an isotropic turbulent viscosity is adopted. For illustration, results are obtained for the case where a stress transport turbulence model is adopted above the riblet crests, an elaboration that leads to the formation of a plausible secondary motion sweeping high momentum fluid towards the wall close to the riblet and thereby raising momentum transport.Nomenclature c _f Skin friction coefficient - c _f Skin friction coefficient in smooth channel at the same Reynolds number - k Turbulent kinetic energy - K ⁺ k/ _w - h Riblet height - S Riblet width - H Half height of channel - Re Reynolds number = volume flow/unit width/ - Modified turbulent Reynolds number - R _t turbulent Reynolds numberk ²/ - P _k Shear production rate ofk, _t (U _i /x _j + U _j /x _i ) U _i /x _j - dP/dz Streamwise static pressure gradient - U _i Mean velocity vector (tensor notation) - U Friction velocity, _w/ where _w=–H dP/dz - W Mean velocity - W _b Bulk mean velocity through channel - y ⁺ yU /v. Unless otherwise stated, origin is at wall on trough plane of symmetry - Kinematic viscosity - _t Turbulent kinematic viscosity - Turbulence energy dissipation rate - Modified dissipation rate – 2(k ^1/2/x _j )² - Density - _k , Effective turbulent Prandtl numbers for diffusion ofk and      

Exact Solutions of the Hydrodynamic Equations Derived from Partially Invariant Solutions

The paper proposes a heuristic approach to constructing exact solutions of the hydrodynamic equations based on the specificity of these equations. A number of systems of hydrodynamic equations possess the following structure: they contain a reduced system of n equations and an additional equation for an extra function w. In this case, the reduced system, in which w = 0, admits a Lie group G. Taking a certain partially invariant solution of the reduced system with respect to this group as a seed:rdquo; solution, we can find a solution of the entire system, in which the functional dependence of the invariant part of the seed solution on the invariants of the group G has the previous form. Implementation of the algorithm proposed is exemplified by constructing new exact solutions of the equations of rotationally symmetric motion of an ideal incompressible liquid and the equations of concentrational convection in a plane boundary layer and thermal convection in a rotating layer of a viscous liquid.     

Transcendentally small transversality in the rapidly forced pendulum

The rapidly forced pendulum equation with forcing sin((t/), where =<₀^p,p = 5, for ₀, sufficiently small, is considered. We prove that stable and unstable manifolds split and that the splitting distanced(t) in the ( ,t) plane satisfiesd(t) = sin(t/) sech(/2) +O( ₀ exp(–/2)) (2.3a) and the angle of transversal intersection,, in thet = 0 section satisfies 2 tan/2 = 2S _s = (/2) sech(/2) +O(( ₀ /) exp(–/2)) (2.3b) It follows that the Melnikov term correctly predicts the exponentially small splitting and angle of transversality. Our method improves a previous result of Holmes, Marsden, and Scheuerle. Our proof is elementary and self-contained, includes a stable manifold theorem, and emphasizes the phase space geometry.     

The chaotic response of a fluttering panel: The influence of maneuvering

The influence of maneuvering on the chaotic response of a fluttering buckled plate on an aircraft has been studied. The governing equations, derived using Lagrangian mechanics, include geometric non-linearities associated with the occurrence of tensile stresses, as well as coupling between the angular velocity of the maneuver and the elastic degrees of freedom. Numerical simulation for periodic and chaotic responses are conducted in order to analyze the influence of the pull-up maneuver on the dynamic behavior of the panel. Long-time histories phase-plane plots, and power spectra of the responses are presented. As the maneuver (load factor) increases, the system exhibits complicated dynamic behavior including a direct and inverse cascade of subharmonic bifurcations, intermittency, and chaos. Beside these classical routes of transition from a periodic state to chaos, our calculations suggest amplitude modulation as a possible new mode of transition to chaos. Consequently this research contributes to the understanding of the mechanisms through which the transition between periodic and strange attractors occurs in, dissipative mechanical systems. In the case of a prescribed time dependent maneuver, a remarkable transition between the different types of limit cycles is presented.Nomenclature a plate length - a _r u _r /h - D plate bending stiffness - E modulus of elasticity - g acceleration due to gravity - h plate thickness - j₁,j₂,j₃ base vectors of the body frame of reference - K spring constant - M Mach number - n 1 + ₀/g - N ₁ applied in-plane force - p–p aerodynamic pressure - P pa ⁴/Dh - q ₀/2 - Q _r generalized Lagrangian forces - R rotation matrix - R ₄ N, a ²/D - t time - kinetic energy - u plate deflection - u displacement of the structure - u _r modal amplitude - v₀ velocity - x coordinates in the inertial frame of reference - z coordinates in the body frame of reference - Ka/(Ka+Eh) - - elastic energy - 2qa ³/D - a/_mh - Poisson's ratio - material coordinates - air density - _m plate density - - _r prescribed functions - _r sin(r z/a) - angular velocity - a/v₀ - skew-symmetric matrix form of the angular velocity     

On a Boundary-Value Problem of Periodic Type for First-Order Linear Functional Differential Equations

We establish unimprovable sufficient conditions for the unique solvability of the boundary-value problem

Flow in porous media I: A theoretical derivation of Darcy's law

Stokes flow through a rigid porous medium is analyzed in terms of the method of volume averaging. The traditional averaging procedure leads to an equation of motion and a continuity equation expressed in terms of the volume-averaged pressure and velocity. The equation of motion contains integrals involving spatial deviations of the pressure and velocity, the Brinkman correction, and other lower-order terms. The analysis clearly indicates why the Brinkman correction should not be used to accommodate ano slip condition at an interface between a porous medium and a bounding solid surface.The presence of spatial deviations of the pressure and velocity in the volume-averaged equations of motion gives rise to aclosure problem, and representations for the spatial deviations are derived that lead to Darcy's law. The theoretical development is not restricted to either homogeneous or spatially periodic porous media; however, the problem ofabrupt changes in the structure of a porous medium is not considered.Roman Letters A interfacial area of the - interface contained within the macroscopic system, m² - A _e area of entrances and exits for the -phase contained within the macroscopic system, m² - A interfacial area of the - interface contained within the averaging volume, m² - A ^* interfacial area of the - interface contained within a unit cell, m² - Ae area of entrances and exits for the -phase contained within a unit cell, m² - B second order tensor used to represent the velocity deviation (see Equation (3.30)) - b vector used to represent the pressure deviation (see Equation (3.31)), m^–1 - d distance between two points at which the pressure is measured, m - g gravity vector, m/s² - K Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the -phase (see Figure 2), m - characteristic length scale for the -phase (see Figure 2), m - n unit normal vector pointing from the -phase toward the -phase (n =–n ) - n _e unit normal vector for the entrances and exits of the -phase contained within a unit cell - p pressure in the -phase, N/m² - p intrinsic phase average pressure for the -phase, N/m² - p –p , spatial deviation of the pressure in the -phase, N/m² - r ₀ radius of the averaging volume and radius of a capillary tube, m - v velocity vector for the -phase, m/s - v phase average velocity vector for the -phase, m/s - v intrinsic phase average velocity vector for the -phase, m/s - v –v , spatial deviation of the velocity vector for the -phase, m/s - V averaging volume, m³ - V volume of the -phase contained within the averaging volume, m³ Greek Letters V/V, volume fraction of the -phase - mass density of the -phase, kg/m³ - viscosity of the -phase, Nt/m² - arbitrary function used in the representation of the velocity deviation (see Equations (3.11) and (B1)), m/s - arbitrary function used in the representation of the pressure deviation (see Equations (3.12) and (B2)), s^–1     

Spin-up in a saturated porous medium

It is shown that, on the Brinkman model, spin-up is confined to boundary layers whose thickness is of order k ^1/2, and the spin-up is established in a time of order k/, where k, , and denote permeability, density, porosity and dynamic viscosity, respectively.     

Nonstationary vibration of a rotating shaft with nonlinear spring characteristics during acceleration through a critical speed (A critical speed of a summed-and-differential harmonic oscillation)

Nonstationary vibration of a flexible rotating shaft with nonlinear spring characteristics during acceleration through a critical speed of a summed-and-differential harmonic oscillation was investigated. In numerical simulations, we investigated the influence of the angular acceleration , the initial angular position of the unbalance _n and the initial rotating speed on the maximum amplitude. We also performed experiments with various angular accelerations. The following results were obtained: (1) the maximum amplitude depends not only on but also on _n and : (2) when the initial angular position _n changes. the maximum amplitude varies between two values. The upper and lower bounds of the maximum amplitude do not change monotonously for the angular acceleration: (3) In order to always pass the critical speed with finite amplitude during acceleration. the value of must exceed a certain critical value.Nomenclature O-xyz rectangular coordinate system - , ₁, ₁ inclination angle of rotor and its projections to thexy- andyz-planes - I _r polar moment of inertia of rotor - I diametral moment of inertia of rotor - i _r ratio ofI _r toI - dynamic unbalance of rotor - directional angle of fromx-axis - c damping coefficient - spring constant of shaft - N _nt ,N _nt nonlinear terms in restoring forees in ₁ and ₁ directions - ₄ representative angle - a small quantity - V. V _u .V _N potential energy and its components corresponding to linear and nonlinear terms in the restoring forees - directional angle - _n coefficients of asymmetrical nonlinear terms - _n coefficients of symmetrical nonlinear terms - coefficients of asymmetrical nonlinear terms experessed in polar coordinates - coefficients of symmetrical nonlinear terms expressed in polar coordinates - rotating speed of shaft - t time - _n initial angular position of att=0 - p natural frequency - p ₁.p _t natural frequencies of forward and backward precessions - , ₁, ₁ total phases of harmonic, forward precession and backward precession components in summed-and-differential harmonic oscillation - , ₁, ₁ phases of harmonic, forward precession and backward precession components in summed-and-differential harmonic oscillation - P, R _t ,R _b amplitudes of harmonic, forward precession and backward precession components in summed-and-differential harmonic oscillation - difference between phases ( = _f – _u) - acceleration of rotor - initial rotating speed - t _t ,r _b amplitudes of nonstationary oscillation during acceleration - (r _t )_max, (r _b )_max maximum amplitudes of nonstationary oscillation during acceleration - (r ₁ ¹ )_max, (r _b ¹ )_max maximum value of angular acceleration of non-passable case - ₀ critical value over which the rotor can always pass the critical speed - p ₁,p ₂,p ₃,p ₄ natural frequencies of experimental apparatus