基于微孔板与折曲通道的亚波长宽带吸声结构设计

本文设计了一种由微穿孔板与折曲通道组成的亚波长宽带复合吸声结构,对该复合吸声器低频宽带吸声机理进行了详细分析,建立了该复合吸声结构的理论吸声解析模型与有限元数值分析模型,完成了吸声理论解和数值解的相互验证.该吸声结构在整体厚度为60 mm时,理论上实现了在200—500 Hz频段内平均吸声系数达0.8的低频高效吸声.同时在整体厚度为90 mm时,理论上实现了180—350 Hz频段内多处峰值达0.95的准完美吸声.该复合吸声结构在低频噪声控制工程中具有一定的应用前景.     

穿纤维微穿孔板吸声系数的有限元仿真

为拓宽微穿孔板的吸声频带,该文用有限元算法建立了典型微穿孔板和穿入不同数量金属纤维的微穿孔板模型,研究了两种微穿孔板的吸声系数、声阻抗和微孔内法向质点速度的空间分布,并进行了试验验证。有限元仿真和试验数据表明:穿入金属纤维可以拓宽微穿孔板的吸声频带,吸声系数也随纤维根数的增加而下降;吸声系数仿真结果与试验结果趋势一致,仿真模型可以有效模拟穿入纤维前后微穿孔板的吸声特性;穿入金属纤维导致黏滞效应引起的低质点速度区域增大,声阻增加,引起吸声系数的降低,而声抗变化不大。研究发现,有限元仿真方法适用于结构相对复杂的微穿孔结构的声学建模,能直观地体现微孔复杂结构的影响,值得继续深入研究和工程应用。     

微穿孔板复合板型声学超材料的低频吸声

针对单层微穿孔板的低频吸声问题提出了微穿孔板复合板型声学超材料结构。将板型声学超材料置入微穿孔板结构的背腔内部实现结构复合。实验结果表明:在相同背腔厚度下,复合结构的吸声性能整体优于单层微穿孔板结构,其中复合结构的吸声曲线从396~892 Hz均大于0.6,在453 Hz处吸声系数达到0.972。利用有限元方法对复合结构进行了仿真,仿真计算的吸声曲线与实验吸声曲线的趋势基本相同,同时发现低频吸声主要由板型声学超材料与声波相互作用贡献。板型声学超材料的吸声峰值的对应频率处,其等效动态质量密度从正变负。在复合结构内部的微穿孔板和板型声学超材料存在相互耦合作用,使得复合结构的第一峰值发生微小偏移。增加板型声学超材料的质量块重量可以使第一吸声峰值向低频移动;保持总背腔厚度不变,增加板型声学超材料的子腔厚度,也可以使第一吸声峰向低频移动。      

微穿孔介电弹性体薄膜的吸声性能试验分析*

针对普通薄膜型降噪结构的吸声性能较差和吸声带宽较窄的问题,本文设计了一种微穿孔的介电弹性体薄膜吸声结构。该结构由穿孔的介电弹性体薄膜与背腔组合而成,目的是拓宽介电弹性体薄膜低频率段的吸声带宽。针对微穿孔的介电弹性体薄膜吸声结构,从试验角度分析穿孔薄膜初始厚度、穿孔孔径及穿孔间距对结构吸声性能的影响。分析结果可知：通过适当增加薄膜的初始厚度,薄膜的整体吸声性能得到有效提升,最大可将319Hz吸声频带的吸声系数从0.2提升至0.7;减小薄膜的穿孔孔径能够有效拓宽穿孔薄膜的吸声频带,可使吸声系数0.4以上的吸声带宽由304Hz拓宽至432Hz;适当控制穿孔间距能够达到更好的吸声效果。     

基于低频吸声超构材料的复合消声器研究*

针对管道内低频噪声难以抑制的问题，本文基于亥姆霍兹共振腔（HR）阵列吸声板和穿孔管消声器组合，设计了一种复合式宽带消声器。首先利用有限元法仿真分析传统穿孔管消声器，发现中低频消声能力较差，通过嵌入HR阵列吸声板吸收中低频噪声。采用仿真与实验的方式研究吸声板的声学性能：在400-1000 Hz频段内的平均吸声系数达到了0.88。然后对复合式消声器进行数值模拟及3D打印阻抗管实验测试对比：复合式消声器在400-1718Hz频率范围内的平均传递损失为18.15 dB ，最终实现了管道内全频带噪声有效控制。     

水下微穿孔吸声体结构设计与试验研究

根据马大猷院士的微穿孔板(MPP)理论,提出在可设计的夹芯复合隐身结构的空腔中附加微穿孔板层的水下微穿孔吸声体。基于微穿孔板的精确计算理论及水下声隐身结构的特点,考虑空腔深度、穿孔板厚度、穿孔直径及穿孔率等对微穿孔板吸声性能的影响,对水下微穿孔吸声体进行了结构设计。利用脉冲声管法对水下微穿孔吸声体试样的吸声系数进行了测量,结果表明:水下微穿孔吸声体有效地拓宽了低频吸声频带,其微穿孔板结构参数的影响规律也与理论分析一致;对于多种吸声机理并存的水下微穿孔吸声体的空腔个数、形状及谐振特性等也是影响吸声性能的重要因素,在实际的工程应用中必须结合所关心的频带对水下微穿孔吸声体进行匹配优化设计。      

水下弹性微穿孔吸声结构吸声系数研究

利用模态叠加法建立了水介质微穿孔板的数学模型,基于声电类比法得到其等效电路模型。研究了弹性微穿孔板和弹性背腔对垂直入射吸声系数的影响。与空气介质中的微穿孔板不同,水下微穿孔板因结构阻抗不足,难以取得满意的吸声效果,为此提出了增强型微穿孔吸声结构,并在水介质阻抗管内对理论结果予以验证。结果表明,随着增强型弹性微穿孔板弯曲刚度的增大,其在[20,2000]Hz范围内的平均吸声系数得到提高,逐步趋近于刚性微穿孔板的结果,弹性背板使微穿孔吸声结构的吸声峰向低频移动,低频吸声效果得到提高。      

机械阻抗与声阻抗结合提高微穿孔板低频吸声性能

提出了在微穿孔板后部引入机械阻抗形成组合结构来解决微穿孔板低频吸声性能差的问题。由机械阻抗板两侧质点速度相同得出机械阻抗单元的传递矩阵,采用传递矩阵法将其与空腔、微穿孔板单元串接,建立组合结构理论计算模型;通过分析品质因子获得带宽与机械阻抗板质量成反比;试验得出组合结构在400 Hz附近有系数为0.8以上的吸声峰值,试验结果与理论计算吻合。在传统微穿孔板共振吸声机制的基础上加入机械共振,能够实现在不增加结构厚度的前提下提高低频吸声性能;降低机械阻抗板质量并且适当控制边界阻尼系数可以实现吸声频带的拓宽。      

微穿孔板的实际极限

对微穿孔板吸声器的构造和吸声特性进行了分析。曾认为低穿孔常数和孔径小可导致宽频带内的高吸声特性。为求得极限,从穿孔系数为1,孔径0．1 mm开始,因为负载声阻和吸声系数可接近1,高吸声系数的共振频率可达1000 Hz,高频率可在吸声范围之内。单片微穿孔板可否用于平常噪声控制,在宽频带内吸声较大?为了比较,半吸声带宽不适用,因为可能包括低吸声系数。建议用吸声系数0．5作为实际吸声底线,为比较微穿孔板的统一标准。更以吸声系数的频率曲线以进行详细比较。负载声阻为1(声阻等于空气特性阻抗)时,微穿孔板的吸声范围约为2．5倍频程,比常用的微穿孔板稍好。负载声阻大于1时,吸声的频率范围显著增加,有些适合宽频带高吸收的要求。将其实现可能是微穿孔板吸声器的重大发展。     

利用含多孔介质微穿孔周期结构增强声吸收

为获得理想吸声性能,提出了一种由多孔材料,微穿孔板及空气层构成的周期复合结构,并利用微穿孔板理论和等效流体多孔材料模型,结合等效电路法进行了分析。结果表明,复合结构显著增强了微穿孔板结构的中低频吸声性能,但其高频性能较单独多孔材料差;采用合适填充比例并联布置多种多孔材料,可适当调节复合结构的吸声性能。此外,周期复合结构的堆叠层数N≥1时,相对单层复合结构,中低频吸声带宽提升至少40%(≥380 Hz);相对多层微穿孔板结构,增大N对相应中低频吸声带宽提升不低于30%(≥300 Hz)。总体上,文中周期复合结构可显著增强传统微穿孔结构的中低频性能,是一种简单高效的中低频宽频降噪方案。      

Sound absorption of microperforated panel mounted with helmholtz resonators

Microperforated panel (MPP) absorbers have been widely used in noise reduction and are regarded as a promising alternative to the traditional porous materials. However, the absorption bandwidth of a single-layer MPP is insufficient to compete with the porous materials. In order to improve the sound absorption ability of the single-layer MPP, MPP mounted with Helmholtz resonators (MPPHR) is introduced. Based on the MPP, Helmholtz resonators theory and electro-acoustical equivalent circuit principle, sound absorption properties of MPPHR are studied. Simulation and experimental results show that MPPHR have two peak frequencies and one anti-resonant frequency. The low-frequency peak is dependent on the Helmholtz resonators, while the high frequency peak is close to the peak of the single-layer MPP. The low-frequency sound absorption peaks move to low frequency with the neck length and the volume of Helmholtz resonators increasing. The high-frequency sound absorption peaks move to high frequency with the volume of Helmholtz resonators cavity increasing. Multiple Helmholtz resonator parallel MPP structure can provide more sound absorption than single MPPHR at low frequency range due to the introduction of more additional sound absorption peaks.     

Improving low-frequency sound absorption of micro-perforated panel absorbers by using mechanical impedance plate combined with Helmholtz resonators

The traditional Micro-perforated plate (MPP) is a kind of clean and non-polluting absorption structure in the middle and high frequency and has been widely used in the field of noise control. However, the sound absorption performance is dissatisfied at low frequencies when the air-cavity depth is restricted. In this paper, a mechanical impedance plate (MIP) is introduced into the traditional MPP structure and a Helmholtz resonator is attached to the MIP. Mechanical impedance plate (MIP) provides a good absorption at low frequency by using mechanism of mechanical resonance and the acoustic energy is dissipated in the form of heat with viscoelastic material. Helmholtz resonator can fill in the defect of the poor absorption effect between the Micro-perforated plate (MPP) and the mechanical impedance plate (MIP). The acoustic impedance of the proposed sound absorber is investigated by using acoustic electric analogy method and impedance transfer method. The influence of the tube’s length of Helmholtz resonator and the number of Helmholtz resonator on the sound absorption is studied. The corresponding results are in agreement with the theoretical calculation and prove that the composite structure has the characteristics of improving the low frequency sound absorption property.     

Broadband low-frequency acoustic absorber based on metaporous composite

Broadband absorption of low-frequency sound waves via a deep subwavelength structure is of great and ongoing interest in research and engineering. Here, we numerically and experimentally present a design of a broadband low-frequency absorber based on an acoustic metaporous composite (AMC). The AMC absorber is constructed by embedding a single metamaterial resonator into a porous layer. The finite element simulations show that a high absorption (absorptance A>0.8) can be achieved within a broad frequency range (from 290 Hz to 1074 Hz), while the thickness of AMC is 1/13 of the corresponding wavelength at 290 Hz. The broadband and high-efficiency performances of the absorber are attributed to the coupling between the two resonant absorptions and the trapped mode. The numerical simulations and experimental results are obtained to be in good agreement with each other. Moreover, the high broadband absorption can be maintained under random incident acoustic waves. The proposed absorber provides potential applications in low-frequency noise reduction especially when limited space is demanded.     

Enhancement of low-frequency sound absorption of microperforated panels by adding a mechanical impedance

In order to solve the bad low frequency sound absorption of the Micro-Perforated panel(MPP)absorber,mechanical impedance was introduced in the back of the MPP absorber to form a composite structure.According to the same particle vibration velocity on both sides of a plate,the mechanical impedance plate transfer matrix could be obtained.The units of the mechanical impedance,cavity and MPP were connected in series with the use of the transfer matrix method,thus creating the composite structure’s theoretical calculation model.The quality factor affecting absorption bandwidth was analyzed.Bandwidth is inversely proportional to the mechanical impedance plate mass.During the experiments,when at close to 400 Hz,the composite structure reached an absorption peak with a coefficient of above 0.8.Experimental results concurred with theoretical calculations.Mechanical resonance is added based on the traditional MPP resonance sound absorption mechanism.Through this,the performance of low frequency sound absorption can be improved without increasing the thickness of the structure.The frequency band can be broadened by reducing the mechanical impedance plate mass and controlling its boundary-damping coefficient.     

The impact of the neck material on the sound absorption performance of Helmholtz resonators

Helmholtz resonators with sound absorption materials filling the neck may have an improved sound absorption capacity. In this work, parallel perforated ceramics with different perforation diameters were installed into the neck of a Helmholtz resonator to improve its acoustic impedance to simultaneously achieve a better acoustic absorption coefficient and a wider absorption bandwidth. An experimental system was built to investigate the effect of the perforation diameters on the sound absorption performance of the resonator. It is found that nonlinear effects near the resonance frequency affect the resonator?s neck mouth impedance and further its sound absorption performance significantly. For frequency range 50–500 Hz, a model of the neck mouth impedance is developed based on a revised Forchheimer relationship. The experimental results are in good agreement with the theoretical model.     

阻尼耦合双层微穿孔板吸声体研究

提出并研究一种利用两板间微缝进行阻尼耦合的双层微穿孔板(DMPP)吸声体。该吸声体在两层微穿孔板(MPP)之间形成一个宽度小于1mm的微缝,因此其阻尼不仅可由板上的微穿孔提供,还可由两板之间形成的微缝提供。采用声电类比法建立了DMPP转移阻抗的理论模型,并进行实验验证,结果表明理论计算结果与实验吻合较好。然后利用建立的理论模型,对单层MPP和DMPP吸声体的吸声性能进行了对比研究,结果表明,相比于单层MPP,DMPP可以利用微缝提供的阻尼显著改善吸声性能,同时减少实际板厚。最后,对DMPP吸声体的吸声性能及其几何参数的关系进行研究,结果表明,当保持其它结构参数不变时,微缝宽度对DMPP吸声系数的提高存在一个最优值,超过或低于此值会导致吸声系数下降。     

Sound absorption characteristics of a double-leaf structure with an MPP and a permeable membrane

As for the sound absorbing system using an MPP (microperforated panel), a double-leaf MPP sound absorber has been studied so far. However, this structure uses two MPPs, which are still expensive, and is disadvantageous when its cost is concerned. Therefore, it is considered that it can be advantageous if one of the leaves can be replaced with a less expensive material keeping high sound absorption performance. In this study, the possibility of producing a useful sound absorbing structure with an MPP and a permeable membrane as an alternative less expensive material is examined. The acoustic properties of this MPP and permeable membrane combination absorber are analysed theoretically with a Helmholtz integral formulation. The absorption performance and mechanism are discussed through the numerical examples. Also, the effect of a honeycomb in the air cavity, which is to be used for reinforcing the structure, is also discussed through a theoretical analysis.     

Experimental study on sound absorption performance of microperforated panel with membrane cell

Microperforated panel (MPP) absorbers have been widely used in noise reduction and are regarded as a promising alternative to the traditional porous materials. However, the absorption bandwidth of a single-layer MPP is insufficient to compete with the porous materials. In order to improve the sound absorption ability of the single-layer MPP, a composite MPP sound absorber with membrane cells (MPPM) is introduced. Sound absorption properties of the MPPM are studied by the impedance tube experiment. Results show that the membranes have a significant influence on the sound impedance. The sound absorption performance of MPPM gradually increases with the increase of the membrane area. The single-layer MPP with some small area membrane cells may have the same effect and single large area membranes. By adjusting the size of the membrane cells, one can implement a sound absorber with a wider absorption bandwidth and higher absorption peaks than the single-layer MPP.