长距离光纤布里渊散射研究

研究了25 km长距离光纤中布里渊散射的功率分布,提出了求解长距离光纤中布里渊散射的耦合强度方程的数值计算方法,与忽略光纤损耗的解析解进行比较,并从实验上加以研究.在此基础上,分析了25 km长距离光纤中布里渊散射过程,得到泵浦波和斯托克斯波沿光纤的功率分布图.     

基于少模光纤的SBS光谱阈值特性分析

受激布里渊散射会影响少模光纤传输系统中的信噪比、传输距离与传输容量,是影响传输系统入纤功率提高的重要因素。对阶跃型少模光纤的受激布里渊散射谱的阈值进行了研究,运用了布里渊散射谱、模式联运谱的数学模型对少模光纤散射特性进行了分析,探讨了少模光纤布里渊散射增益谱、阈值增益系数,以及光纤各参量对少模光纤阈值的影响。分析结果表明：SI-10阶跃型少模光纤中存在五种不同的传播模式,不同模式有各自的传输常数以及有效折射率,各模式相互作用导致模式展宽、增益降低,且布里渊散射谱峰值增益系数为3.9×10-11 m·W-1。阈值增益系数受到光纤传感距离的影响,在相对较短距离传输中阈值急速下降,且其趋势随长度增加渐趋平缓,当光纤长度达到22 km时阈值增益系数趋于常数18.1。少模光纤的阈值因光纤长度的递增而递减,且递减趋势渐缓趋于常数20.5 dBm;少模光纤不同模式受激布里渊散射的阈值也因光纤长度的递增而递减最终趋于常数,且不同模式的阈值因模式阶数的递增而递增;少模光纤的阈值随着光纤衰减系数和纤芯半径的递增而递增,且增加趋势缓慢增大。不同衰减系数的光纤其阈值在不同长度趋于常数,衰减系数越大受激布里渊散射阈值越大越容易趋于一常数。     

光纤光栅法布里-珀罗腔中受激布里渊散射的理论研究

对光纤光栅法布里-珀罗腔中稳态受激布里渊散射模型进行了理论分析,在其耦合强度方程组基础上,推导出仅产生一阶斯托克斯波时,耦合强度方程组的解析表达式,由此计算出光纤光栅法布里-珀罗腔中抽运波与斯托克斯波透射功率和反射功率。对于光纤光栅法布里-珀罗腔中二阶斯托克斯波的产生,推导出光纤光栅法布里-珀罗腔入射端抽运波的解析表达式和忽略光纤损耗时能量守恒方程,利用Shooting和L-M算法数值求解出耦合强度方程组。分析讨论了抽运波,一阶斯托克斯波和二阶斯托克斯波的反射与透射功率随着入射波功率变化的情况。最后,仿真出光纤光栅法布里-珀罗腔中,抽运波与斯托克斯波沿腔长分布的情况。     

光纤移频分布式布里渊光纤传感技术

提出了一种利用布里渊光纤环形腔移频技术实现分布式光纤布里渊传感的方法.该方法基于布里渊光时域分析法原理,将一束单纵模运转激光器输出的激光分为两束|一束光入射布里渊光纤环形腔中产生窄线宽的受激布里渊散射光作为斯托克斯光,另一束光经过低频相位调制后作为泵浦光|斯托克斯光和泵浦光分别相向入射进入传感光纤,通过测量布里渊谱得到光纤温度或应变.利用该方法可将十几GHz的微波频率转化为兆赫信号频率进行探测处理,仅需一台激光器,因此系统结构简单、成本低,还可减小激光器频率波动对测量准确度的影响.实验验证了该方法的可行性.     

Means for easy and accurate measurement of the stimulated Brillouin scattering gain coefficient in optical fiber

We propose and investigate an accurate method for the experimental measurement of the stimulated Brillouin scattering gain coefficient in optical fiber. The gain is extracted from measuring the transmitted pump power at the threshold of stimulated Brillouin scattering (SBS) laser oscillation in a Fabry-Perot cavity formed by Fresnel reflection at the fiber ends. The method is free from a range of uncertainties and difficulties of commonly used approaches and is easy to implement. Experimental evidence of the variation of the SBS gain coefficient with numerical aperture of the fiber, first predicted in [Phys. Rev. Lett. 85, 1879 (2000)], is proven.     

大功率单频多芯光纤放大器中抑制受激布里渊散射的分析

针对多芯光纤完善了描述抽运光、信号光和Stokes信号的速率方程组.考虑了温差对受激布里渊散射的影响,利用有限元法求解温度分布方程组,分析了前向和后向抽运方式、对流系数、Stokes初始功率、光纤掺杂粒子密度和光纤长度对受激布里渊散射增益的影响.研究表明：后向抽运方式在抑制受激布里渊散射方面具有明显优势;减小对流系数有助于抑制受激布里渊散射;提高光纤掺杂密度能够加强抑制受激布里渊散射,同时也有助于提高光纤放大器的斜率效率.比较了在相同最佳光纤长度条件下,单芯和19芯光纤放大器的最高工作温度和受激布里渊散射 关键词： 光纤放大器 受激布里渊散射 大功率 有限元法     

Extension of measurement range in Brillouin optical correlation domain analysis by pump-probe switching

We propose and experimentally demonstrate a novel method for the extension of the measurement range in Brillouin optical correlation domain analysis by switching the pump and probe waves for selectively inducing the stimulated Brillouin scattering (SBS) in the sensing fiber. In this scheme, two correlation peaks are located in the sensing fiber and SBS is alternatively induced at each position by pump/probe selective switching and optical attenuation. In the experiment, twice enlargement of measurement range is successfully achieved with 146-m fiber with a 10-cm spatial resolution.     

CW-pumped polarization-maintaining Brillouin fiber ring laser: I. Self-structuration of Brillouin solitons

Stimulated Brillouin scattering (SBS) of a cw-pump in a long optical fiber ring cavity generates for a given gain G, below a critical feedback R_crit, a backward soliton Stokes pulse at the roundtrip repetition rate, through resonant three-wave interaction between the optical pump wave and backward Stokes wave, and a high frequency (GHz) axial acoustic wave. In Part I, we perform a systematic experimental and numerical exploration of the whole soliton localisation domain for a large set of (G, R) parameters, in a polarization-maintaining Brillouin fiber ring laser in the best conditions of stability and coherence, and we confirm the excellent quantitative agreement of the coherent three-wave model and the experiments.     

基于石英柱模型的光子晶体光纤异常布里渊散射特性的理论研究

通过石英圆柱模型,理论研究了小芯径光子晶体光纤中混合声波模式的色散、模式耦合以及声光相互作用,理论计算出了布里渊散射增益系数谱的双峰结构及其随抽运光波长和温度的演化规律. 理论分析表明光子晶体光纤中布里渊散射增益系数谱的双峰结构源于小芯径光子晶体光纤中混合声波模式之间的模式耦合. 通过温度改变导致的材料参数变化对声波模式色散特性的影响,特别是声波模式耦合点的移动,解释了双峰结构随外界温度的变化规律. 并且,通过理论计算与实验结果的对比讨论了石英圆柱模型的局限性和适用范围. 关键词： 布里渊散射 声光相互作用 模式耦合 光子晶体光纤     

Passive combination of multiple beams in an optical fiber via stimulated Brillouin scattering

We demonstrate passive combination of multiple beams in an optical fiber via stimulated Brillouin scattering (SBS). Four off-axis beams are combined in a long multimode optical fiber using a novel all-optical mount. The combined beam has the high spatial coherence properties of the LP(01) mode owing to the beam cleanup properties of SBS. The threshold for SBS when off-axis pumps are used is shown to be a factor of 13 times higher than for on-axis pump beams. We propose this method would improve the brightness of an array of fiber amplifiers.     

Narrowband optical filter, with a variable transmission spectrum, using stimulated Brillouin scattering in optical fiber

A novel shape-adjustable narrowband optical filter utilizing stimulated Brillouin scattering in an optical fiber is proposed and demonstrated. In this scheme, binary-phase-shift-keying modulation is applied to the pump wave to broaden and shape the Brillouin gain spectrum. By choosing an appropriate modulation data pattern, we realized a flat-top steep-cutoff optical bandpass filter with a 3-dB bandwidth of 1.5 GHz and a 10-dB bandwidth of 2 GHz is realized. In addition, a tunable optical notch filter is also realized by deamplification of the anti-Stokes wave.     

高非线性微结构光纤中基于受激布里渊散射的慢光延迟

全光连续可调的慢光技术在全光网络和光信息处理等领域具有重要的应用前景. 利用自行设计并拉制的高非线性微结构光纤, 实验研究了基于受激布里渊散射的可调谐慢光延迟. 采用单抽运光和单级延迟方案, 当抽运光功率为162.6 mW时, 在长度为120 m的高非线性微结构光纤中获得了最大76 ns的延迟量, 相当于0.76个脉冲宽度. 通过调节抽运光功率的大小, 可以实现对慢光延迟量的可调谐.该慢光延迟方案具有延迟量大、 全光可调谐及与现有光通信系统兼容等优势. 关键词： 慢光 微结构光纤 受激布里渊散射     

Theoretical investigation on the pumping effect of stimulated Brillouin scattering on stimulated Raman scattering in water

The pumping effect of stimulated Brillouin scattering on stimulated Raman scattering is investigated theoretically through the coupled wave equations of stimulated Brillouin scattering and stimulated Raman scattering. The numerical simulations are in agreement with the experimental results. They indicate that the backward stimulated Raman scattering is excited and amplified collectively by both pump laser and stimulated Brillouin scattering.     

Influences of pump wavelength and environment temperature on the dual-peaked Brillouin property of a small-core microstructure fiber

The influences of the pump wavelength and temperature on the dual-peaked Brillouin property of a piece of a small-core microstructure fiber are investigated using the heterodyne method. The experimental results indicate that the dispersion characteristics of the acoustical modes participating in the Brillouin scattering are formed by the coupling of two acoustical modes with different acoustical field distributions. The influence of the pump wavelength can contribute to the variation of the acoustical mode wave vectors. On the other hand, the influence of the environment temperature can contribute to the shift of acoustical mode dispersion map by the variation of the material mechanical parameters and thermal expansion. The model and experiment results demonstrate that the height ratio of the two Brillouin peaks can be controlled by adjusting the pump wavelength or environment temperature.     

Enhancement of stimulated Brillouin scattering of higher-order acoustic modes in single-mode optical fiber

Solving the elastic wave equation exactly for a GeO2-doped silica fiber with a steplike distribution of the longitudinal and shear velocities and density, we have obtained the dispersion, attenuation, and fields of the leaky acoustic modes supported by the fiber. We have developed a model for stimulated Brillouin scattering of these modes in a pump-probe configuration and provided their Brillouin gains and frequencies for an extended range of core sizes and GeO2 doping. Parameter ranges close to cutoff of the acoustic modes and pump depletion enhance the ratio of higher-order peaks to the main peak in the Brillouin spectrum and are suitable for simultaneous strain-temperature sensing.     

High-Q, tunable, photonic microwave single passband filter based on stimulated Brillouin scattering and fiber Bragg grating filtering

We experimentally demonstrate a single passband, photonic microwave bandpass filter scheme based on stimulated Brillouin scattering (SBS) in optical fiber. A single side band (SSB)-modulated probe and a single frequency, tunable pump beam that have been produced by the combination of conventional Mach-Zehnder modulators and fiber Bragg grating filters, are used for the generation of SBS phenomenon in a 1-km long highly nonlinear dispersion-shifted optical fiber. Using the proposed scheme a single microwave passband with a ∼26 MHz bandwidth is readily achieved over a radio frequency tuning range from 1.3 to 9.3 GHz. The maximum Q-factor is measured to be ∼360.     

基于布里渊散射的分布式光纤传感技术

基于布里渊散射的分布式光纤传感技术是目前国内外研究的热点。其中基于时域定位的布里渊分布式光纤传感技术主要分为布里渊光时域反射和布里渊光时域分析两种。国内对基于布里渊光时域反射技术的分布式光纤传感技术的研究报道比较多。介绍了基于布里渊光时域分析技术的分布式光纤传感技术的研究现状,并对基于时域定位的两种传感技术进行了分析对比。总结了布里渊散射分布式光纤传感技术实用化存在的问题及可能的解决方法,指出了该传感技术进一步的发展方向。     

毫米级高分辨率的混沌激光分布式光纤测温技术

近年来,随着分布式光纤传感技术在各大基础设施健康监测领域的广泛应用,人们对能够实现毫米量级精准定位和监测技术的需求日益增长.本文提出了一种基于宽线宽混沌激光的高分辨率分布式光纤测温技术.实验通过改变光反馈混沌源的偏振匹配态和反馈强度等外部参数,产生了–3 dB线宽约为7.5 GHz的宽线宽混沌激光,并在300 m传感光纤实现了空间分辨率为7.05 mm的分布式温度测量.同时,为了抑制光源线宽增加造成的布里渊增益谱恶化,在泵浦路中引入了时间门控技术,其中经脉冲调制后的泵浦光峰值功率提高了约9.5 dB,同时脉冲调制使混沌互相关锁定于脉冲持续时间内,从而布里渊增益谱的信号背景噪声比由约2.28 dB提升为4.55 dB,最终实现了空间分辨率为3.12 mm的分布式温度测量.     

Full modal analysis of the Brillouin gain spectrum of an optical fiber

We present a numerical study of stimulated Brillouin scattering in optical fibers based on a full modal analysis of the acoustic and optical properties. The computation of each acoustic mode supported by the fiber structure allows us an accurate and detailed investigation of the characteristics of the Brillouin gain spectrum. We focus our attention on the contribution of the higher-order acoustic modes which are sometimes ignored because of computational issues in particular on optical fibers that act as acoustic antiwaveguides. Our analysis clearly highlights their role and their dependence on the physical and geometrical structure of the fiber.     

Time delay enhancement in stimulated-Brillouin-scattering-based slow-light systems

We show a simple method of time delay enhancement in slow-light systems based on the effect of stimulated Brillouin scattering. The method is based on the reduction of the absolute Brillouin gain by a loss produced by an additional pump laser. With this method we achieved pulse delays of nearly 100 ns in a standard single-mode fiber. In the presented approach the delay or acceleration of optical signals is decoupled from their amplification or attenuation, which allows the adaptation of the pulse amplitudes to the given application.