纳米金刚石掺混纳米氧化锌的场发射特性

利用水热法制备了菊花状的氧化锌纳米棒,并进行表征,将纳米氧化锌掺入纳米金刚石中配制成电泳液,超声分散后电泳沉积到钛衬底上,再经热处理后进行场发射特性的测试.结果表明:未掺混的金刚石阴极样品的开启电场为7.3V/μm,在20V/μm的电场下,场发射电流密度为81μA/cm2;掺混后阴极样品的场发射开启电场降低到4.7~6.0V/μm,在20V/μm电场下,场发射电流密度提高到140~158μA/cm2.原因是纳米ZnO掺入后,增强了涂层的电子输运能力、增加了有效发射体数目,提高了场增强因子β,而金刚石保证了热处理后涂层与衬底的良好键合,形成了欧姆接触,降低了场发射电流的热效应.场发射电流的稳定性随掺混ZnO量的增加而下降,要兼顾场发射电流密度及其稳定性,适量掺入ZnO可有效提高纳米金刚石的场发射性能.     

激光晶化形成纳米硅材料的场电子发射性质研究

利用KrF准分子激光退火超薄非晶硅膜,并结合热退火技术制备了单层纳米硅薄膜并研究了薄膜的场电子发射性质.在晶化形成的纳米硅薄膜中可以观测到稳定的场电子发射现象,其开启电场从原始淀积的非晶硅薄膜的17V/μm降低到8.5V/μm,而场发射电流密度可以达到0.1mA/cm².激光晶化后形成的纳米硅材料的场电子发射特性的改善可以从薄膜表面形貌的改变以及高密度纳米硅的形成所导致的内部电场增强作用来解释. 关键词： 纳米硅 场发射 激光晶化     

InN纳米线的低压化学气相沉积及其场发射特性研究

利用低压化学气相沉积方法在以Au作催化剂的Si衬底上生长了InN纳米线. 扫描电子显微镜分析表明，这些纳米线的直径在60—100 nm的范围内, 而其长度大于1 μm.高分辨透射电子显微镜图像表明，合成的纳米线中含有六方相和立方相的InN晶体.这些InN纳米线具有良好的场发射特性和稳定的场发射电流，其开启场为10.02 V/μm(电流密度为10 μA/cm²)，在24 V/μm 的电场下，其电流密度达到5.5 mA/cm².此外，对InN纳米线的场发射机理也进行了讨论. 关键词： InN纳米线 场电子发射 非线性Fower-Nordheim曲线     

碳、碳氮和硼碳氮纳米管场发射性能的比较研究

采用高温热解法在860℃分别制备出了碳、碳氮和硼碳氮纳米管，提纯后利用丝网印刷工艺分别将它们制备成薄膜，并测试了它们的场发射性能.结果表明：碳纳米管、碳氮纳米管和硼碳氮纳米管薄膜的开启电场分别为2.22，1.1和4.4V/μm，当电场增加到5.7V/μm时，它们的电流密度分别达到1400，3000μA/cm²和小于50μA/cm².碳和碳氮纳米管薄膜的场增强因子分别为10062和11521.可见，碳氮纳米管的场发射性能优于碳纳米管，而硼碳氮纳米管的场发射性能比前两者要差.解释了这三种纳米管场发射性能差别的原因. 关键词： 碳纳米管 碳氮纳米管 硼碳氮纳米管 场发射     

两步化学沉积法制备ZnO薄膜及其场发射特性

在低温常压条件下,以ITO玻璃为衬底,采用电化学法与湿化学法结合的两步化学沉积法制备了团簇状ZnO薄膜。利用XRD,SEM分析了薄膜结构和表面形貌,并采用二极管结构在高真空条件下对薄膜进行了场发射性能测试。稳定发射后,开启电场为3.0 V/μm。当电场为5.8 V/μm时,电流密度为583.3 μA/cm²。研究表明:两步化学沉积法低温制备ZnO薄膜是可行的,且该薄膜具有良好的场发射性能。     

Er3+掺杂对ZnO/GaN发光二极管电致发光性能的调控

采用水热法制备了Er~(3+)掺杂的ZnO纳米棒阵列,通过场发射扫描电镜、X单晶衍射谱仪、透射电镜、微区显微光谱仪等对其形貌结构和发光性能进行了表征。结果表明,掺杂前后ZnO纳米棒的形貌及晶型结构未发生改变,Er~(3+)被均匀地掺杂至ZnO纳米棒中,并未发现形成Er_2O_3;掺杂Er~(3+)后样品的光致发光光谱显示400 nm左右蓝光部分占比先提高后减少,其可见光占比减少归因于Er~(3+)填补了一部分锌空位缺陷,同时抑制了一部分氧空位缺陷。结合荧光寿命光谱分析也可发现其辐射发光部分寿命延长,表明荧光辐射效率提高。最终选取掺杂浓度为30%的单根ZnO纳米棒制备ZnO/GaN异质结发光二极管,与未掺杂Er~(3+)的样品相比,其电致发光强度提高了5倍。本研究可为ZnO基电致发光器件的性能改善提供一种简便可行的方法。     

Er^(3+)掺杂对ZnO/GaN发光二极管电致发光性能的调控EI北大核心CSCD

采用水热法制备了Er^(3+)掺杂的ZnO纳米棒阵列,通过场发射扫描电镜、X单晶衍射谱仪、透射电镜、微区显微光谱仪等对其形貌结构和发光性能进行了表征。结果表明,掺杂前后ZnO纳米棒的形貌及晶型结构未发生改变,Er^(3+)被均匀地掺杂至ZnO纳米棒中,并未发现形成Er_(2)O_(3);掺杂Er^(3+)后样品的光致发光光谱显示400 nm左右蓝光部分占比先提高后减少,其可见光占比减少归因于Er^(3+)填补了一部分锌空位缺陷,同时抑制了一部分氧空位缺陷。结合荧光寿命光谱分析也可发现其辐射发光部分寿命延长,表明荧光辐射效率提高。最终选取掺杂浓度为30%的单根ZnO纳米棒制备ZnO/GaN异质结发光二极管,与未掺杂Er^(3+)的样品相比,其电致发光强度提高了5倍。本研究可为ZnO基电致发光器件的性能改善提供一种简便可行的方法。     

白碳纳米晶薄膜及其场致电子发射特性

利用微波等离子体化学气相沉积方法,以甲烷、氢混合气体为反应气体,具有钛镀层的玻璃作为衬底,制备了具有sp¹杂化结构的白碳纳米晶薄膜。利用X射线衍射、俄歇电子能谱,以及扫描电子显微镜对薄膜结构进行了表征。以白碳纳米晶薄膜为阴极,以镀有ITO透明导电薄膜玻璃为阳极,采用二极管结构,测试了白碳纳米晶薄膜的场致电子发射特性。开启电场为2.5 V/μm,在电场为5 V/μm时的电流密度为200μA/cm²。对白碳纳米晶薄膜生长机理,以及其场致电子发射机制进行了讨论。     

类金刚石和碳氮薄膜的电化学沉积及其场发射性能研究

利用电化学方法在室温下成功地沉积了类金刚石(DLC)薄膜和非晶CN_x薄膜，并 对制备条件进行了讨论.通过扫描电子显微镜、傅里叶变换红外光谱技术，分析了薄膜的表面形貌和化学结合状态.场发射测量结果表明：DLC膜和非晶CN_x的开启场分别为88和 10V/μm；并且在23V/μm的电场下，DLC膜和非晶CN_x膜的发射电流密度分别达到10 和037mA/cm². 关键词： 电化学沉积 类金刚石薄膜 x薄膜')" href="#">CN_x薄膜 场致电子发射     

合成温度和N2/O2流量比对碳纤维衬底上生长的SnO2纳米线形貌及场发射性能影响

采用化学气相沉积法系统研究了合成温度和N₂/O₂流量对生长在碳纤维衬底上的SnO₂纳米线形貌及场发射性能的影响规律. 利用扫描电镜(SEM)、透射电镜(TEM), X射线衍射(XRD)及能谱仪(EDS)对产物细致表征, 结果表明, SnO₂纳米线长径比随反应温度的升高而增大; 随N₂/O₂流量比值的增大先增大后变小, 场发射测试表明, 合成温度780 ℃, N₂/O₂流量比为300 : 3 时SnO₂纳米线阵列具有最佳的场发射性能, 开启电场为1.03 V/μm, 场强增加到1.68 V/μm时, 发射电流密度达0.66 mA/cm², 亮度约2300 cd/m².     

Modulation of field emission properties of vertically aligned ZnO nanorods with aspect ratio and number density

Vertically aligned ZnO nanorod arrays with different aspect ratios were synthesized by hybrid wet chemical route. Modulation of the field emission properties (FE) with aspect ratio of ZnO nanorods was examined. With the increase in the aspect ratio, the emission current density increases from 0.02 to 8 μA/cm² at 7.0 V/μm. Turn-on voltage was seen to decrease from 9.6 to 7 V/μm at a current density of 10 μA/cm² with the increase in aspect ratio in the ZnO films. The interrelation between the FE characteristics (emission thresholds, current density, surface uniformity, etc.) and microstructure of the ZnO nanostructure obtained from scanning electron microscopy (SEM) and atomic force microscopy (AFM) was discussed. Quality of the ZnO nanorods was also examined by using Raman spectroscopy and Fourier transformed infrared spectroscopy (FTIR). It was found that the observed enhancements of FE characteristics could mainly be attributed to the increase in aspect ratio and associated number density of ZnO nanorods.     

ZnO nanorods with different morphologies and their field emission properties

ZnO nanorods with different morphologies were grown by changing the temperature of the process using the thermal vapor deposition method without a catalyst. The X-ray diffraction pattern of these nanorods showed a single-crystalline wurtzite structure and a c-axis orientation. The turn-on fields of the pencil-like and normal ZnO nanorods were 1.7 V/μm and 2.2 V/μm at a current density of 0.1 μA/cm², and the emission current density from the ZnO nanorods reached 1 mA/cm² at bias fields of 5.1 V/μm and 7.5 V/μm, respectively. The results indicated that ZnO nanorods could give sufficient brightness as a field emitter in a flat panel display.     

Field emission behavior of cuboid zinc oxide nanorods on zinc-filled porous silicon

Single-crystalline zinc oxide (ZnO) nanorods with cuboid morphology have been prepared on the zinc-filled porous silicon substrate using a vapor phase transport method. Field-emission measurements showed that the turn-on field and threshold field of the cuboid ZnO nanorods film were about 3.2 and 8.2 V/μm respectively. From the emitter surface, a homogeneous emission image was observed with emission site density (ESD) of ∼10⁴ cm⁻². The better emission uniformity and the high ESD may be attributed to a large number of ZnO nanocrystallites as emitter on the surface of the nanorod end contributing to emission.     

Chemical solution-process method to synthesize ZnO nanorods with ultra-thin pinheads and ultra-thin nanobelts

ZnO nanorods with 30 nm-diameter ultra-thin pinheads and ultra-thin nanobelts were successfully synthesized using a thiourea solution to etch nanorods and nancombs, which were obtained by a conventional thermal evaporation method. The materials obtained were investigated by field emission scanning electron microscopy and energy-dispersive X-ray fluorescence. The data shows that hydrogen ions play an important role in synthesizing ZnO nanorods with ultra-thin pinheads and ultra-thin nanobelts. Field emission plots indicated that the turn-on field was reduced from 2.10 V/μm to 1.55 V/μm after thiourea solution treatment at a current density of 0.1 μA/cm². Room-temperature photoluminescence spectra from ZnO nanostructures showed the PL spectrum peaks shifted towards short wavelengths with a large enhancement of UV bands compared with those of ZnO nanorods and nanocombs. PACS 75.55.Gs; 61.46.-w; 81.40.Wx; 78.55.-m; 78.60.Fi     

Controlled growth and field emission properties of zinc oxide nanopyramid arrays

Single-crystalline, pyramidal zinc oxide nanorods have been synthesized in a large quantity on p-Si substrate via catalyst-free thermal chemical vapor deposition at low temperature. SEM investigations showed that the nanorods were vertically aligned on the substrate, with diameters ranging from 60 to 80 nm and lengths about 1.5 μm. A self-catalysis VLS growth mechanism was proposed for the formation of the ZnO nanorods. The field emission properties of the ZnO nanopyramid arrays were investigated. A turn-on field about 3.8 V/μm was obtained at a current density of 10 μA/cm², and the field emission data was analyzed by applying the Fowler-Nordheim theory. The stability of emission current density under a high voltage was also tested, indicating that the ZnO nanostructures are promising for an application such as field emission sources.     

Synthesis and field emission of patterned ZnO nanorods

A simple and self-catalytic method has been developed for synthesizing finely patterned ZnO nanorods on ITO-glass substrates under a low temperature of 500 °C. The patterned ZnO nanorod arrays, a unit area is of 400 × 100 μm², are synthesized via vapor phase transport method. The surface morphology and composition of the as-synthesized ZnO nanorods are characterized by means of scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The mechanism of formation of ZnO nanorods is also discussed. The measurement of field emission (FE) reveals that the as-synthesized ZnO nanorods arrays have a turn-on field of 3.3 V/μm at the current density of 0.1 μA/cm² and a low threshold field of 6.2 V/μm at the current density of 1 mA/cm². So this approach must have a potential application of fabricating micropatterned oxide thin films used in FE-based flat panel displays.     

Field electron emission improvement of ZnO nanorod arrays after Ar plasma treatment

Vertically well-aligned single crystal ZnO nanorod arrays were synthesized and enhanced field electron emission was achieved after radio-frequency (rf) Ar plasma treatment. With Ar plasma treatment for 30 min, flat tops of the as-grown ZnO nanorods have been etched into sharp tips without damaging ZnO nanorod geometrical morphologies and crystallinity. After the Ar ion bombardment, the emission current density increases from 2 to 20 μA cm⁻² at 9.0 V μm⁻¹ with a decrease in turn-on voltage from 7.1 to 4.8 V μm⁻¹ at a current density of 1 μA cm⁻², which demonstrates that the field emission of the as-grown ZnO nanorods has been efficiently enhanced. The scanning electron microscopy (SEM) results, in conjunction with the results of transmission electron microscopy (TEM), Raman spectroscopy and photoluminescence observation, are used to investigate the mechanisms of the field emission enhancement. It is believed that the enhancements can be mainly attributed to the sharpening of rod tops, and the decrease of electrostatic screening effect.     

Electrochemical synthesis of Cu/ZnO nanocomposite films and their efficient field emission behaviour

The Cu/ZnO nanocomposite films have been synthesized by cathodic electrodeposition and characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), photoluminescence (PL) and field emission microscope (FEM). The XRD pattern shows a set of well defined diffraction peaks, which could be indexed to the wurtzite hexagonal phase of ZnO. In addition, characteristic diffraction peaks corresponding to Cu and Zn are also observed. The SEM image shows formation of two-dimensional (2D) hexagonal sheets randomly distributed and aligned almost normal to the substrate. Uniformly distributed small clusters of Cu nanoparticles possessing average diameter of ∼25 nm, as revealed from the TEM image, are seen to be present on these 2D ZnO sheets. The selected area electron diffraction (SAED) image confirms the nanocrystalline nature of the Cu particles. From the field emission studies, carried out at the base pressure of ∼1 × 10⁻⁸ mbar, the turn-on field required for an emission current density of 0.1 μA/cm² is found to be 1.56 V/μm and emission current density of ∼100 μA/cm² has been drawn at an applied field of 3.12 V/μm. The Cu/ZnO nanocomposite film exhibits good emission current stability at the pre-set value of ∼10 μA over a duration of 5 h. The simplicity of the synthesis route coupled with the better emission properties propose the electrochemically synthesized Cu/ZnO nanocomposite film emitter as a promising electron source for high current density applications.     

Synthesis of Cu-ZnO and C-ZnO nanoneedle arrays on zinc foil by low temperature oxidation route: Effect of buffer layers on growth, optical and field emission properties

Different densities of ZnO nanoneedle films have been prepared by pre-coated zinc foils with thin layer of copper and carbon followed by thermal oxidation at 400 °C in air. The X-ray diffraction patterns show well defined peaks, which could be indexed to the wurtzite hexagonal phase of ZnO. The scanning electron microscope images clearly reveal formation of ZnO needles on the entire substrate surface. The X-ray photoelectron spectroscopy studies indicate that Cu and C ions are incorporated into the ZnO lattice. Photoluminescence studies evaluate different emission bands originated from different defect mechanism. From the field emission studies, the threshold field, required to draw emission current density of ∼100 μA/cm², is observed to be 2.25 V/μm and 1.57 V/μm for annealed zinc foil pre-coated with copper and carbon, respectively. The annealed film with copper layer exhibits good emission current stability at the pre-set value of ∼100 μA over a duration of 4 h. The results show that buffer layer is an important factor to control the growth rate, resulting in different density of ZnO needles, which leads to field emission properties. This method may have potential in fabrication of electron sources for high current density applications.     

Patterned uniformly orientated silicon nanocrystallite films and efficient field emission characteristics

Patterned uniformly (100)-orientated silicon nanocrystallite (SiNC) films were fabricated based on hydrogen ion implantation technique and typical electrochemical anodic etching method. The surface morphology and microstructure characteristics of the films were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and atomic force microscopy. The efficient field emission with low turn-on field of about 3.2 V/μm at current density of 0.1 μA/cm² was obtained. The emission current density from the SiNC films reached 1 mA/cm² under a bias field of about 11 V/μm. The experimental results demonstrate that the SiNC films have great potential applications for flat panel displays.