共查询到16条相似文献,搜索用时 125 毫秒
1.
2.
3.
4.
5.
燃气轮机合成气双旋流非预混燃烧室的设计及实验测试 总被引:1,自引:0,他引:1
本文针对上海交通大学25 kW燃气轮机性能试验台的合成气燃烧室开展了设计研究,完成了燃烧室样机的加工与实验测试。研究过程中,首先对合成气燃烧室开展了结构设计;采用双旋流结构的燃烧器进行合成气燃烧火焰组织;采用了燃烧室头部贫燃方式(低当量比)设计以保证燃烧室低排放特性;利用双层壁冷却方式进行火焰筒壁面冷却。在燃烧室结构设计的基础上,利用数值方法系统分析了合成气双旋流非预混燃烧室工作特性,完成了合成气非预混母型燃烧室的设计优化。根据优化方案,完成了燃烧室样机的加工、安装,并进行了实验性能测试。实验结果表明实验工况该燃烧室燃烧稳定,NO_x排放小于25 mg/m~3@15%O_2。 相似文献
6.
将某型烧天然气的燃气轮机改为烧中热值合成气,需要改造燃烧室、燃机控制系统、燃料供给系统和相关配套系统,并校核燃机关键部件的通流匹配情况.在完成合成气燃烧室设计、试验和制造之后,需要进行燃气轮机组的安装调试、现场测试和考核.本研究所建立了燃气轮机现场测试平台;进行了合成气燃气轮机的安装调试、168小时连续运行考核和第三方的燃机性能考核;初步掌握了燃机控制系统和配套系统的改造技术.现场测试平台用贴片式热电偶对火焰筒壁温进行了监测,用示温漆测量了满负荷工况火焰筒壁温分布,用燃气分析仪测量了燃烧室效率和污染物排放.考核结果表明燃机功率、燃机热耗、燃烧效率、污染物排放基本达标. 相似文献
7.
进气温度对微燃机燃烧室燃烧特性的影响分析 总被引:1,自引:0,他引:1
本文通过实验研究了在保持微型燃气轮机燃烧室出口排气温度不变的情况下,改变进口空气温度对燃烧室燃烧特性的影响.结果表明,随着燃烧室进气温度的增大,燃烧效率提高,燃烧室出口温度不均匀性系数减小,热阻增大,总压恢复系数有所降低.同时,实验结果还表明,随着燃烧室进口空气温度的增大,燃烧室出口处CO及未燃烬碳(UHC)排放浓度显著降低,但NO排放浓度则增大.根据实验结果,本文还分析了进气温度的改变对燃烧室燃烧特性的影响规律,为今后微型燃气轮机燃烧室的研制及改进提供了参考依据. 相似文献
8.
亥姆霍兹共振器抑制振荡燃烧理论分析 总被引:2,自引:0,他引:2
燃烧室是燃气轮机的核心部件之一,其中的燃烧过程的关键技术之一是如何避免和抑制振荡燃烧现象.本文简要阐述了发生振荡燃烧的机理以及亥姆霍兹共振器抑制振荡燃烧的声学分析,并且通过线性分析与CFD计算相结合的研究方法对燃烧系统的燃烧稳定性进行计算;同时分析了共振器共振频率和安装位置对燃烧稳定性的影响,得出在不同因素影响下,系统的稳定性和模态.这些分析有助于我们在设计和运行燃烧系统时,实现燃烧系统的安全、高效和清洁运行. 相似文献
9.
燃气轮机燃烧室化学反应器网络模型研究 总被引:3,自引:0,他引:3
本文针对CFD燃烧室设计方法在计算时间以及计算的准确度上的不足,发展了一种计算量较小的、能够快速准确地预测燃气轮机燃烧室污染物排放的化学反应器网络模型方法(CRN).该方法首先根据CFD的计算结果对燃烧室进行分区,不同的区域采用不同的化学反应器模型进行模拟,反应器之间的连接关系以及入口参数都根据CFD的结果确定.本文采用这种方法对某个燃烧富氢合成气的重型燃气轮机燃烧室的NO_x排放随燃料加湿量的变化进行了预测,并与现场测量的结果进行了比较.计算结果与现场试验数据吻合得很好,证明这是一种很好的预测燃烧室NO_x排放的方法,与CFD方法相比预测精度有了很大提高,而且在计算时间上小了几个数量级. 相似文献
10.
11.
12.
13.
对Solar低排放预混燃烧系统的燃烧稳定性进行了数值研究.应用非定常N-S方程、雷诺应力紊流模型及涡团耗散燃烧模型,数值模拟了该类型燃烧器在不同的燃料空气供给条件下的气流流动特性和压力振荡特性,并给出了不稳定发生时压力和速度振荡的幅值和频率.根据供给条件的不同,燃烧可以是稳定的或是不稳定的,取决于燃料到火焰前沿的迟滞时间.采用CFD方法,可精确地获得燃料到火焰前沿的迟滞时间,证实了所采用的模型能够精确预测不稳定燃烧的出现及振荡特性.通过调整燃料与空气的供给条件,可使振荡激励或阻尼. 相似文献
14.
15.
16.
Ekenechukwu C. Okafor K.D. Kunkuma A. Somarathne Akihiro Hayakawa Taku Kudo Osamu Kurata Norihiko Iki Hideaki Kobayashi 《Proceedings of the Combustion Institute》2019,37(4):4597-4606
Recent studies have demonstrated stable generation of power from pure ammonia combustion in a micro gas turbine (MGT) with a high combustion efficiency, thus overcoming some of the challenges that discouraged such applications of ammonia in the past. However, achievement of low NOx emission from ammonia combustors remains an important challenge. In this study, combustion techniques and combustor design for efficient combustion and low NOx emission from an ammonia MGT swirl combustor are proposed. The effects of fuel injection angle, combustor inlet temperature, equivalence ratio, and ambient pressure on flame stabilization and emissions were investigated in a laboratory high pressure combustion chamber. An FTIR gas analyser was employed in analysing the exhaust gases. Numerical modeling using OpenFOAM was done to better understand the dependence of NO emissions on the equivalence ratio. The result show that inclined fuel injection as opposed to vertical injection along the combustor central axis resulted to improved flame stability, and lower NH3 and NOx emissions. Numerical and experimental results showed that a control of the equivalence ratio upstream of the combustor is critical for low NOx emission in a rich-lean ammonia combustor. NO emission had a minimum value at an upstream equivalence ratio of 1.10 in the experiments. Furthermore, NO emission was found to decrease with ambient pressure, especially for premixed combustion. For the rich-lean combustion strategy employed in this study, lower NOx emission was recorded in premixed combustion than in non-premixed combustion indicating the importance of mixture uniformity for low NOx emission from ammonia combustion. A prototype liner developed to enhance the control and uniformity of the equivalence ratio upstream of the combustor further improved ammonia combustion. With the proposed liner design, NOx emission of 42?ppmv and ammonia combustion efficiency of 99.5% were achieved at 0.3?MPa for fuel input power of 31.44?kW. 相似文献