Effect of Carbon Fiber Surface Oxidation on Tribological Properties of PTFE Composite under Oil-Lubricated Conditions

Air-oxidation and ozone surface treatment of carbon fibers (CF) on tribological properties of CF reinforced polytetrafluoroethylene (PTFE) composites under oil-lubricated conditions was investigated. Experimental results revealed that ozone treated CF reinforced PTFE (CF/PTFE) composite had the lowest friction coefficient and wear under various applied loads and sliding speeds compared with untreated and air-oxidated composites. X-ray photoelectron spectroscopy (XPS) study of the carbon fiber surface showed that, after ozone treatment, oxygen concentration was obviously increased, and the amount of oxygen-containing groups on CF surfaces were increased greatly. The increase in the amount of oxygen-containing groups enhanced interfacial adhesion between CF and PTFE matrix, and large scale rubbing-off of PTFE was prevented; therefore, the tribological properties of the composite were improved.     

The friction and wear properties of divinylbenzene-grafted UHMWPE fiber-filled serpentine/PTFE composite

Divinylbenzene-grafted Ultra-high-molecular-weight polyethylene (UHMWPE) fibers were used to reinforce the Polytetrafluoroethylene (PTFE) composite and the friction and wear behaviors of UHMWPE/PTFE composite were studied on the ring-block machine under vacuum condition. The worn surfaces of specimens were investigated using scanning electron microscopy and energy dispersive spectroscopy (EDS). The results showed that the friction coefficient and temperature of UHMWPE/PTFE composites with surface-treated UHMWPE fiber were apparently lower than that with untreated one. In conclusion, the surface treatment favored the improvement of the higher interface strength and so had good effect on improving the tribological properties of the composites. The dominant wear mechanisms were adhesion wear, plastic deformation, brittle facture, and spalling. The EDS analysis of the worn surface indicated the trend of the tribochemical reaction of the Fe related to the transfer of the PTFE.     

Tribological Properties of Surface-Modified Graphene Filled Carbon Fabric/Polyimide Composites

To improve the wear resistance of carbon fabric reinforced polyimide (CF/PI) composite, surface-modified graphene (MG) was synthesized and employed as a filler. The flexural strength, Rockwell hardness and thermal properties of the composites were tested. The composites were also evaluated for their tribological properties in a ring-on-block contact mode under dry sliding conditions. The results showed that the wear rate of MG reinforced CF/PI composites was reduced when compared to unfilled CF/PI composite. It was found that the 1?wt% MG filled CF/PI composites exhibited the optimal tribological properties. The worn surface, wear debris and transfer films were analyzed by scanning electron microscopy (SEM) and optical microscopy (OM) with the results helping to characterize the wear mechanism.     

Friction and Wear Behaviors of Surface-Modified Carbon Fabric/Epoxy Resin Composites

Carbon fabric (CF) was pretreated by air-plasma bombardment and then further modified by deposition of polydopamine on the surface of the pretreated CF. Epoxy resin composites reinforced by unmodified or surface-modified carbon fabric were fabricated. The friction and wear behaviors of the resulting composites were evaluated in a ring-on-block contact mode. The flexural strength and Rockwell hardness of the composites were also evaluated. The morphologies of the worn surfaces of the unmodified and modified composites were analyzed by scanning electron microscopy. The surface treatment increased the surface roughness and changed the surface topography of the CF, which contributed to enhancing the interfacial adhesion of the composites and thus improved the mechanical properties and tribo-performance. The friction and wear properties of both the unfilled and filled composites were highly dependent on the load and sliding velocity. Moreover, the results were supplemented with scanning electron micrographs to help understand the possible wear mechanisms.     

Studies on wettability, mechanical and tribological properties of the polyurethane composites filled with talc

A series of polyurethane (PU)/talc composites modified by a high molecular weight hydroxyl-terminated polydimethylsiloxane (HTPDMS) were prepared. The effect of the talc content on the mechanical, wettability and tribological properties of the PU composites was studied. Tensile strength of the PU composites reached to the maximum after adding 5% talc. The water contact angles (CA) of the original surfaces and worn surfaces of the polyurethane composites were measured. The experimental results indicated that the contact angles of the worn surface increased after friction. The friction and wear experiments were tested on a MRH-3 model ring-on-block test rig at different sliding speeds and loads under dry sliding and water lubrication. Experimental results revealed that the talc contributed to largely improve the tribological properties of the PU composites. The coefficient of friction (COF) of the composites increased with increasing talc. Scanning electron microscopic (SEM) investigations showed that the worn surfaces of the talc filled PU composites were smoother than pure polyurethane under given load and sliding speed.     

Effects of carbon fiber surface treatment on the tribological properties of 2D woven carbon fabric/polyimide composites

Polyacrylonitrile (PAN)-based carbon fabric (CF) was modified with strong HNO₃ oxidation and then introduced into polyimide (PI) composites. The friction and wear properties of the carbon fabric reinforced polyimide composites (CFRP), sliding against GCr15 stainless steel rings, were investigated on an M-2000 model ring-on-block test rig under dry sliding. Experimental results revealed that the carbon fiber surface treatment largely reduced the friction and wear of the CFRP. Compared with the untreated ones, the surface-modified CF can enhance the tribological properties of CFRP efficiently due to the improved adhesion between the CF and the PI matrix. Scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) study of the carbon fiber surface showed that the fiber surface became rougher and the oxygen concentration increased greatly after surface treatment, which improved the adhesion between the fiber and the PI matrix and improved the friction-reduction and anti-wear properties of the CFRP. An erratum to this article can be found at     

Effects of Aramid Fiber and Polytetrafluoroethylene on the Mechanical and Tribological Properties of Polyimide Composites in a Vacuum

Polyimide composites filled with aramid fiber (AF) and polytetrafluoroethylene (PTFE) were prepared by hot press molding. The thermal, mechanical, and tribological properties of the composites were studied systematically. The friction and wear behavior, sliding against GCr15 steel balls, were evaluated in a ground-based wear in space simulation facility using a ball-on-disk tribosystem. The morphologies of the worn surfaces during the sliding process of the composites were analyzed by scanning electron microscopy to reveal the wear mechanism. It was found that the heat-resisting performance and the hardness of the composites were minimally affected by the additives. The flexural strength of polyimide/AF/PTFE (PI-3) decreased when PTFE was added. The wear resistance increased and the coefficient of friction decreased due to the effect of both fillers. In vacuum, the friction coefficients of polyimide (PI-1), polyimide/AF (PI-2), and PI-3 increased slightly with sliding velocity, while the opposite results were obtained in air. With the increase of air pressure the friction coefficients of the samples increased.     

The Mechanical and Tribological Properties of Aramid (Twaron) Fabric/Polytetrafluoroethylene Composites

A series of composites with Twaron fabric as reinforcement and polytetrafluoroethylene (PTFE) as matrix were fabricated with various contents of PTFE, viz. 30, 40, 50, 60, and 70 vol%. The Rockwell hardness and tensile strength of the composites were tested according to the corresponding standards. The composites were also evaluated for their tribological behaviors on an MPX-2000A friction and wear tester. The worn surface and wear debris of the composites were observed by scanning electron microscopy (SEM) and the mechanism is discussed. The PTFE content in the composites had a great influence on both the mechanical and tribological properties. The composite with 40 vol% PTFE provided the proper wetting of the fibers and the best load transfer efficiency and, hence, showed the best mechanical properties and tribological behaviors.     

Development and characterization of alkali treated abaca fiber reinforced friction composites

Abaca fibers show tremendous potential as reinforcing components in composite materials. The purpose of this study is to investigate the effect of abaca fiber content on physical, mechanical and tribological properties of abaca fiber reinforced friction composites. The friction composites were fabricated by a compression molder and investigated using a friction test machine. The experiment results show that surface treatment of abaca fibers could improve the mechanical properties of abaca fiber and interface bonding strength of the abaca fiber and composite matrix. Density of friction composites decreased with the increasing of abaca fiber content (0 wt%–4 wt%). The different content of abaca fibers had less effect on hardness of specimens, whereas large of impact strength. The specimen F3 with 3 wt% abaca fibers had the lowest wear rate and possessed the best wear resistance, followed by specimen F4 with 4 wt% abaca fibers. The worn surface morphologies were observed using the Scanning Electron Microscopy for study the tribological behavior and wear mechanism. The results show that a large amount of secondary contact plateaus presented on the worn surface of specimen F3 which had relatively smooth worn surface.     

Tribological Properties of Hydroxyl-Terminated Liquid Nitrile Rubber-Modified Polyurethane/Epoxy Interpenetrating Polymer Network Composites

A series of castor oil-based polyurethane (PU)/epoxy resin (EP) graft interpenetrating polymer network (IPN) composites modified by two kinds of hydroxy-terminated liquid nitrile rubber (HTLN) was prepared. A systematic investigation of the tribological properties of the two kinds of HTLN-modified PU/EP IPN composites was carried out through a pin-on-disk arrangement under dry sliding conditions. Experimental results revealed that the incorporation of HTLN can improve the friction and wear properties of PU/EP IPN significantly. Both the friction coefficient and wear loss decreased with increasing content of HTLN. The worn surfaces of the samples were analyzed using scanning electron microscope and a three-dimensional (3D) noncontact surface-mapping profiler; the results showed that the worn surfaces of the PU/EP IPN composites became smooth when the HTLN was added. The mechanisms for the improvement of tribological properties are discussed.     

Ultraviolet or Atomic Oxygen Effects on Tribological Properties of the Carbon Fibers/Polyimide Composites

Carbon fibers-reinforced polyimide composites (CF-PI) were fabricated by means of a hot press molding technique. To contrast the effects of ultraviolet and atomic oxygen irradiation under high vacuum on the tribological properties of CF-PI composites, the friction and wear properties of the composites sliding against GCr15 steel ball before and after irradiation were conducted in high vacuum on a ball-on-disk test rig. The experimental results revealed that CF-PI composites exhibited higher modulus and lower coefficient of friction and worn rate value than pure polyimide under high vacuum. However, the coefficient of friction of composites increased and the worn rate value decreased after ultraviolet or atomic oxygen irradiation, which slightly affected the tribological properties of CF-PI composites. The chemical composition of the composites changed after irradiation was inspected by X-ray photoelectron spectroscopy. Microstructure of the worn surfaces of the tested composites was investigated by scanning electron microscopy to reveal the wear mechanism.     

Study on the Tribological Properties of Carbon Fabric/Polyimide Composites Filled with SiC Nanoparticles

Carbon fabric reinforced thermoplastic polyimide composites have significant applications in the field of tribology. However, there are relatively few studies that have been focused on the investigation of these materials. In the present study, carbon fabric/polyimide (CF/PI) composites, reinforced further with SiC nanoparticles, were prepared by dip-coating and hot press molding methods. Rockwell hardness and flexural testing of the composites were conducted. The friction and wear behavior of the resulting carbon fabric composites were evaluated in a ring-on-block contact mode under dry sliding condition. The results showed that the SiC nanoparticles significantly improved the hardness and flexural strength when compared to the CF/PI composites without the SiC additions. The CF/PI composites reinforced with 5 vol% SiC nanoparticles demonstrated the most beneficial mechanical and tribological properties compared to the composites with greater and lesser SiC nanoparticles. Scanning electron microscopy (SEM) and optical microscopy (OM) were employed in order to study the mechanism of tribological behavior. A continuous and thin transfer film formed during the friction test of the composites led to a significant improvement of the tribological properties.     

Investigation of Transfer Behaviors of Embedded Polytetrafluoroethylene in Different Metal Substrates

Transfer behaviors of molded polytetrafluoroethylene (PTFE) blocks embedded in metal substrates were studied using a DFPM reciprocating tribometer under designed conditions. The substrate properties markedly affected the embedded PTFE transfer behaviors. For instance, the surface friction coefficient when embedded in AISI-1045 steel had evident fluctuations even after 1000 cycles although the friction coefficient decreased with the increase of the sliding cycles. On the other hand, the friction coefficient when the PTFE was embedded in 2024Al was remarkably reduced during the first 200 cycles, reaching a low and stable state. The loads played different roles in the transfer process; a higher load was advantageous for the steel-PTFE embedded composites, but it resulted in the opposite result for the Al-PTFE embedded composites. The motion direction of the GCr15 tribometer steel ball had no remarkable effect on the transfer behaviors. The worn surface of the substrates and the steel ball were observed and analyzed using scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The results indicate that the efficiency of second transfer film formation on the 2024Al substrate was better than for the AISI-1045 steel. The adhesion properties of Al enhanced the mechanical transfer of PTFE during the friction process.     

A Study on the Mechanical and Tribological Properties of Carbon Fabric/PTFE Composites

Carbon fabric reinforced polytetrafluoroethylene (PTFE) composites with different PTFE content, viz. 30, 40, 50, 60, and 70 vol%, were fabricated by a dispersion impregnation technique followed by a hot-press process. The composites were evaluated for their mechanical and tribological properties. The tribological tests were conducted on a friction and wear tester with a ring-on-block arrangement. The mechanical properties were also tested and their relationship with tribological properties was analyzed. The worn surface and wear debris were analyzed by a scanning electron microscope (SEM) to study the wear mechanism. It was found that the resin content had a great influence on both the mechanical properties and the tribological properties, and the tribological properties were correlated with the mechanical properties. The composite with 50 vol% PTFE showed promising tribological behaviors under the selected test conditions.     

The Effects of Copper and Polytetrafluoroethylene (PTFE) on Thermal Conductivity and Tribological Behavior of Polyoxymethylene (POM) Composites

The effects of copper and polytetrafluoroethylene (PTFE) on thermal conductivity and tribological behavior of polyoxymethylene (POM) composites were investigated by a hot disk thermal analyzer and an M-2000 friction and abrasion testing machine. The results indicated that the incorporation of 3 wt% copper particles into POM had little effect on the thermal conductivity of POM composites, but led to the decreased friction coefficient and wear rate of composites. As the copper content was increased, the thermal conductivity increased and reached 0.477 W m^?1 K^?1 for POM-25% Cu composite, an increase of 35.9% compared with that of unfilled POM, while the friction coefficient and wear rate of composites also increased. The incorporation of PTFE into POM-Cu composites had a negligible effect on the thermal conductivity of composites, but helped in the formation of a continuous and uniform transfer film and resulted in the reduction in the friction coefficient and wear rate of composites. The POM-15% Cu-10% PTFE composite, with a value of wear rate similar to unfilled POM possessed higher thermal conductivity and lower friction coefficient.     

The gamma irradiation of PBO fiber on the mechanical and tribological properties of PTFE composites

The mechanical and tribological behavior of gamma irradiated poly(p-phenylene benzobisoxazole) (PBO) fiber filled polytetrafluoroethylene (PTFE) composites was investigated. The gamma irradiated PBO fiber composite had the highest inter-laminar shear strength value of all the combinations because its higher bond strength may have hindered a large fiber/matrix debonding. X-ray photoelectron spectroscopy results indicate that the contents of polar groups on the surface of gamma irradiated PBO fiber increase compared to PBO fiber. The wear tests were conducted on a ring-on-block apparatus using composite block against polished metal counterparts under dry sliding conditions. It can also be found that gamma irradiation treatment was helpful to the improvement of the anti-wear ability of the PTFE composite which was related to the abrasive wear mechanism.     

Influence of the Addition of Nano-porous Graphite/Parafffin Additive on the Wear Properties of Phenol-Formaldehyde Resin Composites

Phenol-formaldehyde resin (PF) composites with a nano-porous graphite additive (NPGA) in various contents were fabricated and the wear behaviors under low and high sliding speeds were studied. The addition of NPGA significantly improved the wear resistance of the PF. The specific wear rates of PF composites under low sliding speed first decreased with increasing NPGA and then slightly increased when the NPGA content surpassed 15?wt%; the specific wear rate of the composite with 15?wt% NPGA was reduced by 77% compared with the neat PF. Under high sliding speed the specific wear rates of the composite material decreased continuously with increasing NPGA content and the maximum wear resistance of the composite with 20?wt% NPGA was more than 12 times that of the neat phenolic resin. The results are attributed to the combined effects of load-capacity and the lubrication role of the included NPGA. The surface morphology of the worn surface was characterized, and the wear mechanism for the composites is discussed.     

Study on the Tribological Properties of Carbon Fabric Reinforced Phenolic Composites Filled with Nano-Al2O3

Carbon fabric reinforced phenolic (CFRP) composites filled with nano-Al₂O₃ were prepared by a dip-coating and heat molding process and the tribological properties of the resulting composites under different sliding conditions were investigated systematically on a block-on-ring test rig. The worn surfaces were observed in a scanning electron microscope (SEM) to understand the mechanism. Nano-Al₂O₃ particles, as the filler, were effective in reducing the friction coefficient and wear rate of the CFRP composites. The steady state friction coefficient of the CFRP composites filled with 4 wt.% nano-Al₂O₃ particles was about 65.5% of that of unfilled CFRP composites, and the wear rate, in this case, was about 74.7% of that of unfilled CFRP composites. Tribological tests under different sliding conditions revealed that the filled CFRP composites seemed to be more suitable than unfilled CFRP composites for tribological applications under higher sliding speed and load. Moreover, the wear resistances of the unfilled and filled CFRP composites were found to be related to the stability of the transfer film on the counterface.     

Dry sliding wear characteristics of in situ synthesized Al-TiC composites

Abstract

Aluminum-based composites containing 0.06, 0.09, 0.12 fractions of in situ-synthesized TiC (Titanium carbide) particles have been prepared through in-melt reaction from Ai–SiC–Ti system following a simple and cost-effective stir-casting route. The TiC forms by the reaction of Ti with carbon which is released by SiC at temperatures greater than 1073 K. However, some amount of titanium aluminide (Al₃Ti) is also formed. The formation of TiC has been confirmed through X-ray diffraction studies of the composite. The hardness and tensile strength have been found to increase with increasing amount of TiC. The friction and wear characteristics of the composites have been determined by carrying out dry sliding tests on pin-on-disc machine at different loads of 9.8 N, 19.6 N, 29.4 N, 39.2 N at a constant sliding speed of the 1 m/s speed. The wear rate i.e. volume loss per unit sliding distance has been found to increase linearly with increasing load following Archard’s law. However, both the wear rate and friction coefficient have been observed to decrease with increasing amount of TiC in the composite. This has been attributed to (i) a relatively higher hardness of composites containing relatively higher amount of TiC resulting in a relatively lower real area of contact and (ii) the formation of a well-compacted mechanically mixed layer of compacted wear debris on the worn surface which might have inhibited metal–metal contact and resulted in a lower wear rate as well as friction coefficient.     

The effect of surface treatment of carbon fiber on the flexural property of thermoplastic polyimide composite

Rare earth solution (RES) surface modification and air-oxidation methods were used to improve the interfacial adhesion of the carbon fiber reinforced polyimide (CF/PI) composite. The flexural property of the PI composites reinforced by the carbon fibers treated with different surface modification methods was comparatively investigated. Results showed that the flexural strength of CF/PI composite was improved after RES treatment. The improvement of impact and flexural property of the CF/PI composite was mainly due to the improvement in interfacial adhesion after RES treatment. X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the oxygen concentration was obviously increased after RES treatment. The increase in the amount of organic functional groups increased the interfacial adhesion between CF and PI matrix.