Influence of Cu doping on the microstructure,optical properties and photoluminescence features of Cd0.9Zn0.1S nanoparticles

Cd_0.9−xZn_0.1Cu_xS (0≤x≤0.06) nanoparticles were successfully synthesized by a conventional chemical co-precipitation method at room temperature. Crystalline phases and optical absorption of the nanoparticles have been studied by X-ray diffraction (XRD) and UV–visible spectrophotometer. XRD confirms the phase singularity of the synthesized material, which also confirmed the formation of Cd–Zn–Cu–S alloy nanocrystals rather than separate nucleation or phase formation. Elemental composition was examined by the energy dispersive X-ray analysis and the microstructure was examined by scanning electron microscope. The blue shift of absorption edge below Cu=2% is responsible for dominance of Cu⁺ while at higher Cu concentration dominated Cu²⁺, d–d transition may exist. It is suggested that the addition of third metal ion (Cu²⁺/Cu⁺) is an effective way to improve the optical property and stability of the Cd_0.9Zn_0.1S solid solutions. When Cu is introduced, stretching of Cd–Zn–Cu–S bond is shifted lower wave number side from 678 cm⁻¹ (Cu=0%) to 671 cm⁻¹ (Cu=6%) due to the presence of Cu in Cd–Zn–S lattice and also the size effect. The variation in blue band emission peak from 456 nm (∼2.72 eV) to 482 nm (∼2.58 eV) by Cu-doping is corresponding to the inter-band radiation combination of photo-generated electrons and holes. Intensity of red band emission centered at 656 nm significantly increased up to Cu=4%; beyond 4% it is decreased due to the quenching of Cu concentration.     

Emission of Cu-related complexes in ZnO:Cu nanocrystals

Photoluminescence (PL), its temperature dependence, scanning electronic microscopy (SEM) and X ray diffraction (XRD) have been applied for the comparative study of varying the emission, morphology and crystal structure of ZnO and ZnO:Cu nanocrystals (NCs) versus technological routines, as well as the dependence of ZnO:Cu NC parameters on the Cu concentration. A set of ZnO and ZnO Cu NCs was prepared by the electrochemical (anodization) method at a permanent voltage and different etching durations with follows thermal annealing at 400 °C for 2 h in ambient air. The size of ZnO NCs decreases from 300 nm×540 nm down to 200 nm×320 nm with etching duration increasing. XRD study has confirmed that thermal annealing stimulates the ZnO oxidation and crystallization with the formation of wurtzite ZnO crystal lattice. XRD method has been used for monitoring the lattice parameters and for confirming the Cu doping of ZnO Cu NCs. In ZnO Cu NCs four defect related PL bands are detected with the PL peaks at 1.95–2.00 eV (A), 2.15-2.23  eV (B), 2.43–2.50 eV (C) and 2.61–2.69 eV (D). Highest PL intensities of orange, yellow and green emissions have been obtained in ZnO Cu NCs with the Cu concentration of 2.28 at%. At Cu concentration increasing (≥2.28 at%) the PL intensities of the bands A, B, C decrease and the new PL band peaked at 2.61–2.69 eV at 10 K appears in the PL spectrum. The variation of PL intensities for all PL bands versus temperature has been studied and the corresponding activation energies of PL thermal decay have been estimated. The type of Cu-related complexes is discussed using the correlation between the PL spectrum transformation and the variation of XRD parameters in ZnO Cu NCs.     

Effect of rare-earth donor Ce3+ doping at A-site of PLSZNT on dielectric and piezoelectric properties

Dielectric and piezoelectric properties of [Pb_0.976La_0.014−xCe_xSr_0.01][Zr_0.57Ti_0.43]_{(0.9975−((0.014−x)/4)−(x/4))}Nb_0.002O₃ (PLCSZNT) ceramic compositions for 0 ⩽ x ⩽ 1 mol% were investigated. The XRD analysis showed the presence of single rhombohedral phase. Grain size and density increased until 0.6 mol% Ce and further Ce concentration inhibited the grain growth. The stability of rhombohedral phase has been supported by tolerance factor and average electronegativity difference. The room temperature dielectric response (ε_RT) increased up to 0.6 mol% combined with a significantly reduced dielectric loss (Tan δ) and low Curie temperature (T_c). The higher piezoelectric properties associated with low Ce concentration are attributed to rhombohedral phase. The optimum dielectric and piezoelectric properties were found in 0.6 mol% Ce composition which could be suitable for possible piezoelectric applications.     

Effect of Fe doping on the structural and gas sensing properties of ZnO porous microspheres

Fe-doped ZnO porous microspheres composed of nanosheets were prepared by a simple hydrothermal method combined with post-annealing, and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller N₂ adsorption–desorption measurements and photoluminescence (PL) spectra. In this paper we report Fe doping induced modifications in the structural, photoluminescence and gas sensing behavior of ZnO porous microspheres. Our results show that the crystallite size decreases and specific surface area increases with the increase of Fe doping concentration. The PL spectra indicate that the 4 mol% Fe-doped ZnO has higher ratio of donor (V_O and Zn_i) to acceptor (V_Zn) than undoped ZnO. The 4 mol% Fe-doped ZnO sample shows the highest response value to ppb-level n-butanol at 300 °C, and the detected limit of n-butanol is below 10 ppb. In addition, the 4 mol% Fe -doped ZnO sample exhibits good selectivity to n-butanol. The superior sensing properties of the Fe-doped porous ZnO microspheres are contributed to higher donor defects contents combined with larger specific surface area.     

Dielectric,optical and structural properties of Bi4V2−xSrxO11−δ (0.05≤x≤0.20)

Composition Bi₄V_2−xSr_xO_11−δ (0.05≤x≤0.20) is synthesized by melt quench technique followed by heat treatment at 800 °C for 12 h. These compounds are characterised by X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, UV–visible spectroscopy, impedance spectroscopy and scanning electron microscopy. X-ray diffraction patterns of all the samples show γ-phase stabilization at room temperature except x=0.05 heat treated sample. The optical band gap of all the samples is observed in semiconducting range. The lowest and the highest optical band gap is 2.39 eV and 2.57 eV for x=0.10 heat treated and x=0.20 quenched samples, respectively. The highest value of dielectric constant is obtained ~10⁷ with very low dielectric loss for x=0.15 and 0.20 samples at ~350 °C and below 10 Hz. The grain size increases with dopant concentration leads to increase the dielectric constant.     

NMR and electric impedance study of lithium mobility in fast ion conductors LiTi2 − xZrx(PO4)3 (0 ≤ x ≤ 2)

Materials of the LiTi_2 − xZr_x(PO₄)₃ series (0 ≤ x ≤ 2) were prepared and characterized by powder X-ray (XRD) and neutron diffraction (ND), ⁷Li and ³¹P Nuclear Magnetic Resonance (NMR) and Electric Impedance techniques. In samples with x < 1.8, XRD patterns were indexed with the rhombohedral R3̅c space group, but in samples with x ≥ 1.8, XRD patterns display the presence of rhombohedral and triclinic phases. The Rietveld analysis of the LiTi_1.4Zr_0.6(PO₄)₃ neutron diffraction (ND) pattern provided structural information about intermediate compositions. For low Zr contents, compositions deduced from ³¹P MAS-NMR spectra are similar to nominal ones, indicating that Zr⁴⁺ and Ti⁴⁺ cations are randomly distributed in the NASICON structure. At increasing Zr contents, differences between nominal and deduced compositions become significant, indicating some Zr segregation in the triclinic phase. The substitution of Ti⁴⁺ by Zr⁴⁺ stabilizes the rhombohedral phase; however, electrical performances are not improved in expanded networks of Zr-rich samples. Below 300 K, activation energy of all samples is near 0.36 eV; however, above 300 K, activation energy is near 0.23 eV in Ti-rich samples and close to 0.36 eV in Zr-rich samples. The analysis of electrical data suggests that the amount of charge carriers and entropic terms are higher in Zr-rich samples; however, the increment of both parameters does not compensate lower activation energy terms of these samples. As a consequence of different contributions, the bulk conductivity of Zr-rich samples, measured at room temperature, is one order of magnitude lower than that measured in Ti-rich samples.     

Structural and optical properties of Mn-doped ZnO nanocrystalline thin films with the different dopant concentrations

The transparent nanocrystalline thin films of undoped zinc oxide and Mn-doped (Zn_1−xMn_xO) have been deposited on glass substrates via the sol–gel technique using zinc acetate dehydrate and manganese chloride as precursor. The as-deposited films with the different manganese compositions in the range of 2.5–20 at% were pre-heated at 100 °C for 1 h and 200 °C for 2 h, respectively, and then crystallized in air at 560 °C for 2 h. The structural properties and morphologies of the undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/Vis spectroscopy. The analyzed results indicates that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn related phases. Room temperature photoluminescence is observed for the ZnO and Mn-doped ZnO thin films.     

Structural,optical and magnetic properties of Cu and V co-doped ZnO nanoparticles

Zn_0.98−xCu_xV_0.02O (x=0, 0.01, 0.02 and 0.03) samples were synthesized by the sol–gel technology to dope up to 3% Cu in ZnO. Investigations of structural, optical and magnetic properties of the samples have been done. The results of X-ray diffraction (XRD), transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS) indicated that the V and Cu ions were incorporated into the crystal lattices of ZnO. With Cu doping concentration increasing up to 2 at%, the XRD results showed that all diffraction peaks corresponded to the wurtzite structure of ZnO. Photoluminescence (PL) measurements showed that Zn_0.98−xCu_xV_0.02O powders exhibited that the position of the ultraviolet (UV) emission peak of the samples showed an obvious red-shift and the green emission peak enhanced significantly with Cu doping in ZnVO nanoparticle. Magnetic measurements indicated that room temperature ferromagnetism (RTFM) of Zn_0.98−xCu_xV_0.02O was an intrinsic property when Cu concentration was less than 3 at%. The saturation magnetization (M_s) of Zn_0.98−xCu_xV_0.02O (x=0, 0.01 and 0.02) increased with the increase of the Cu concentration.     

Theoretical and experimental investigation on structural and electronic properties of Al/O/Al,O-doped WS2

Effects of the doping atom (O, Al, and (Al, O)) on structural and electronic properties of the monolayer WS₂ have been studied by using first-principles calculations. Results show that the covalent character of W–S bonding has been enhanced after doping. Meanwhile, W–O, Al–S and W–S bonds of (Al, O) co-doped WS₂ monolayer have higher covalent character compared with O-doped and Al-doped WS₂ monolayer of this work. After doping with Al (or Al, O) atoms, Fermi level moves close to the valence band and the dopant atoms produce the defect energy levels, indicating that Al doped and (Al, O) co-doped WS₂ monolayer both have p-type conductivity. O-doped and (Al, O) co-doped WS₂ ultrathin films was prepared on Si substrates. Results of Raman spectra show the formation of the O-doped and (Al, O) co-doped WS₂ films. Moreover, compared with the pure WS₂, the approximate reduction of 0.43 eV and 0.46 eV for W 4f and S 2p in binding energy after (Al, O) co-doped shows that p-type doping of (Al, O) co-doped WS₂ has been verified.     

Sonocatalytic degradation of a textile dye over Gd-doped ZnO nanoparticles synthesized through sonochemical process

The present study was performed to sonochemically synthesize Gd_xZn_1 − xO (x = 0–0.1) nanoparticles for sonocatalysis of Acid Orange 7 (AO7) in an aqueous medium. The results of X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) analysis confirmed proper synthesis of Gd-doped sonocatalyst. 5% Gd-doped ZnO nanoparticles with band gap of 2.8 eV exhibited the highest sonocatalytic decolorization efficiency of 90% at reaction time of 90 min. The effects of initial dye concentration and sonocatalyst dosage on decolorization efficiency were evaluated. In the presence of sodium sulfate, sodium carbonate and sodium chloride the decolorization efficiency decreased from 90 to 78, 65 and 56%, respectively. Among various enhancers, the addition of potassium periodate improved the decolorization efficiency from 90 to 100%. The highest decolorization efficiency was obtained at pH value of 6.34 (90%). The decolorization efficiency decreased only 6% after 4 repeated runs. Therefore, Gd-doped ZnO nanoparticles can be used as a promising catalyst for degradation of organic pollutants with great reusability potential.     

Synthesis,characterization and magnetic properties of lightly doped La2−xSrxCuO4 (x = 0.04) nanoparticles

Lightly doped La_2−xSr_xCuO₄ (x = 0.04) nanoparticles with different particle sizes have been successfully prepared by a sol–gel method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared transmission (IR) spectra and superconducting quantum interference device (SQUID) magnetometer. All samples are single phase and have an orthorhombic unit cell. As the particle size reduces, it is found that the IR band at around 685 cm⁻¹ corresponding to the in-plane Cu–O asymmetrical stretching mode shifts to higher frequency and the magnetization exhibits a large enhancement at low temperature. The magnetic susceptibility of all samples follows a modulated Curie law between ∼20 K and ∼100 K and the Curie constant displays a strong dependence on the particle size. It is suggested that as the particle size decreases surface effects should play an important role in the magnetic properties of the nanoparticles.     

Effect of strontium addition on europium-doped ceria properties

Nanopowders of composition Ce_0.9(Eu_1 ? xSr_x)_0.1O_2 ? δ (x = 0, 0.1, 0.3, 0.5, and 0.7) were prepared by the Pechini method. The microstructure and properties of powders and sintered ceramics are discussed in this paper. X-ray diffraction (XRD) and Raman spectroscopy revealed that all powders calcined at 550 °C were single phase, with the cubic fluorite-type structure. The good sintering properties of the synthesized nanopowders allowed us to obtain dense ceramics (> 96% theoretical density). Dense ceramics with density higher than 96% of the theoretical value were obtained without the need of sintering aid. The morphology of the sintered ceramics was evidenced by scanning electron microscopy (SEM). The ionic conductivities of doped and co-doped ceria ceramics were investigated as a function of temperature by using AC impedance spectroscopy in the temperature range 250–800 °C. Impedance spectra indicate a significant diminution of grain boundary resistance after partial substitution of Eu with Sr in europia-doped ceria sample, especially in the low and intermediate-temperature range. The best conductivity was evidenced for the Ce_0.9Eu_0.09Sr_0.01O_2 ? δ composition.     

Synthesis and characterization of (Bi,Cu)Sr2(RE,Ca)Cu2Oz (RE: Y or rare-earth element)

Samples with nominal compositions of x = 0–0.1 in (Bi_(1+3x)/3Cu_(2?3x)/3)Sr₂(RE_1?xCa_x)Cu₂O_z ((Bi,Cu)-“1-2-1-2”; RE: Y or rare-earth element) were synthesized by a solid-state reaction method and characterized by means of X-ray diffractometry (XRD). It is confirmed that the (Bi,Cu)-“1-2-1-2” forms only when RE = Y, Dy and Ho. Single- or nearly single-phase samples are obtained for x = 0–0.05 and the Ca-free composition of this compound is determined to be (Bi_1/3Cu_2/3)Sr₂RECu₂O_z. Since ionic radii of Y, Dy and Ho are very close to each other and this seems to be an essential factor for the stability of the (Bi,Cu)-“1-2-1-2”.     

X-ray photoelectron spectroscopy of CeO2–Na2O–SiO2 glasses

A series of (CeO₂)_x–(Na₂O)_0.3–(SiO₂)_(0.7−x) glasses, where 0.025 ≤ x ≤ 0.075, have been synthesized and investigated by mean of X-ray photoelectron spectroscopy (XPS). The Ce 3d spin-orbit doublet was curve fitted in order to quantify the proportions of each cerium oxidation state in these glasses. It was found that Ce ions are predominantly in the Ce(III) state in glasses with compositions x ≤ 0.075, while mixed Ce valences were found in the glass with composition x = 0.10. The O 1s spectra have also been curve fitted with two components, one from bridging oxygen (BO) and the other from non-bridging oxygen atoms (NBO). The measured number of NBO, based on the fact that only oxygen atoms in the site Si–O–Na⁺ contribute to the NBO peak, was found to be constant at ∼35% for all samples, in good agreement with the value calculated from the glass composition and inductively coupled plasma (ICP) suggesting that Ce ions enter the network as a glass intermediate. The thermal measurements done on these glasses agree well with the XPS findings.     

Correlation between phosphorus concentration and opto-electrical properties of doped a-Si:H films

Phosphorus doped hydrogenated amorphous silicon (a-Si:H) films were prepared by decomposition of silane using RF plasma glow discharge. Both DC dark conductivity measurements, and spectrophotometric optical measurements through the range 200–3000 nm were recorded for the prepared films. The DC conductivity activation energy E_a decreased from 0.8 eV for the undoped sample to 0.34 eV for the highest used doping value. The optical energy gap E_g decreased ranging from 1.66 eV to 1.60 eV. The refractive index n, the density of charge carriers N/m* and the plasma frequency ω_p showed an opposite behavior, i.e. an increase in value with doping. Fitting the dispersion values to Sellmeier equation led to the determination of the material natural frequency of oscillating particles. A correlation between the changes in these parameters with the doping has been attempted.     

On the origin of blue light emission from Ge-nanocrystals containing a-SiOxfilms

We have studied the photoluminescence of a-Si_xGe_yO_{1 − x − y}films with average Ge-nanocrystal sizes ranging from over 100 nm down to 2 nm. No systematic peak shift of the luminescence bands at 3.0 eV and 2.0 eV with the diameter of the nanocrystals is observed. Comparision with a simplified confinement model shows that quantum size effects cannot explain the blue luminescence. We propose the Ge²₀defect as a likely source for this band, based on considerations about the crystallization process.     

Impacts of neodymium on structural,spectral and dielectric properties of LiNi0.5Fe2O4 nanocrystalline ferrites fabricated via micro-emulsion technique

Soft ferrites are technologically advanced smart materials and their properties can be tailored by controlling the chemical composition and judicial choice of the metal elements. In this article we discussed the effect of rare earth neodymium (Nd³⁺) on various properties of LiNi_0.5Nd_xFe_2−xO₄ spinel ferrites. These ferrites have been synthesized by facile micro-emulsion route and characterized by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), a.c. electrical conductivity and thermal analysis. The influence of Nd³⁺ doping on structural and electrical parameters has been investigated. XRD analysis revealed the formation of single cubic spinel structure for x≤0.07. Few traces of secondary phase (NdFeO₃) were found for x≥0.105. The secondary phase induced owing to the solubility limit of Nd³⁺ cations in these ferrites. The lattice parameter (a) and crystallite size (D) both exhibit non-linear relation. The values of “a” and “D” were found in the range 8.322–8.329 Å and 25–32 nm respectively. These variations were attributed to the larger ionic radius of Nd³⁺ cations as compared to the host cations and lattice strain produced in these ferrites. The dielectric parameters were studied in the range 1 MHz to 3 GHz and these parameters were damped by Nd³⁺ incorporation and also by increasing the frequency. The reduced dielectric parameters observed in wide frequency range proposed that these nanocrystalline ferrites are potential candidates for fabricating the devices which are required to operate at GHz frequencies.     

Temperature dependent structural and optical properties of tin oxide nanoparticles

Nanocrystalline tin oxide (SnO₂) powders were synthesized through wet chemical route using tin metal as precursor. The morphology and optical properties, as well as the effect of sintering on the structural attributes of SnO₂ particles were analyzed using Transmission electron microscopy (TEM), UV–visible spectrophotometry (UV–vis) and X-ray diffraction (XRD), respectively. The data revealed that the lattice strain plays a significant role in determining the structural properties of sintered nanoparticles. The particle size was found to be 5.8 nm, 19.1 nm and 21.7 nm for samples sintered at 300 °C, 500 °C, and 700 °C, respectively. Also, the band gaps were substantially reduced from 4.1 eV to 3.8 eV with increasing sintering temperatures. The results elucidated that the structural and optical properties of the SnO₂ nanoparticles can be easily modulated by altering sintering temperature during de novo synthesis.     

In situ characterization of transport properties of superconducting (Cu, C)-system thin films

Transport properties of (Cu, C)Ba₂CuO_x [(Cu, C)-1201] thin films have been characterized by in situ temperature dependence of resistivity, without breaking vacuum from the deposition to the measurement. In in situ transport properties measurements, the obtained results reveal that (Cu, C)Ba₂CuO_x films exhibit T_c > 20 K on the cased of conductivity at 290 K (σ_[290 K]) > 4 × 10² S/cm and temperature coefficient of resistivity (TCR) > 1.5 × 10^?3 K^?1, and doping level of them should be in between under-doped and optimally-doped states. Their results suggest that there would be possible to further increases of T_c, and XPS data suggest that (Cu, C)-system should have the excellent dopability in their charge reservoir and the possibility of low anisotropy.     

Luminescence properties of co-doped ZnS:Ni,Mn and ZnS:Cu,Cd nanoparticles

Transition metal doped ZnS:Ni and ZnS:Cu and co-doped ZnS:Ni, Mn and ZnS:Cu, Cd nanoparticles were synthesized through the chemical precipitation method in an air atmosphere. The XRD analysis of co-doped samples shows the formation of cubic phase. The average size of nanoparticles ranges from 3.6 to 5.5 nm. The formation of co-doped nanoparticles was confirmed by XRD and PL analysis. The PL spectra show that the obtained nanoparticles have good crystal quality. An optimum concentration of transition metals was selected in co-doped ZnS nanoparticles.