电磁悬浮熔炼的温度特性

利用一般电磁悬浮熔炼感应器，球形试样悬浮情况下，悬浮力和悬浮试样输入功率表达式，建立了不含悬浮感应器电流的悬浮试样输入功率表达式.利用这些表达式，结合自然对流情况下，球形试样在气体介质中的功率耗散模型，建立了悬浮熔炼工艺参量与悬浮熔炼试样温度之间的关系.以(TbDy)Fe2合金在Ar气保护情况下，在一定工艺条件下的电磁悬浮熔炼为例，得到了电磁悬浮熔炼各种工艺参量与悬浮试样温度的关系.通过对计算结果的分析，结合实际电磁悬浮熔炼特点，得到了降低电磁悬浮熔炼试样最低温度的措施：减小悬浮试样的半径；在能够实现悬浮 关键词： 电磁悬浮熔炼 悬浮力 输入功率 耗散功率     

Levitation in the field of a nonsuperconducting coil with magnetic flux stabilization

A method providing the “frozen flux” conditions in a nonsuperconducting coil is suggested and demonstrated with a model. The feasibility of permanent magnet stable levitation in the field of the coil with magnetic flux stabilization and mean current control is shown. The method allows researchers to exploit permanent magnet-superconducting body interaction in physical devices, for example, to reproduce, using nonsuperconducting coils, the frozen magnetic flux conditions required for the stable levitation of the magnet over a superconducting body.     

冷坩埚磁悬浮熔炼的电磁场分析

针对冷坩埚熔炼过程的悬浮特性问题,利用准三维耦合电流算法,就坩埚结构、电磁频率及感应圈电流等影响因素进行分析,为冷坩埚结构和磁悬浮熔炼的优化设计提供依据。结果显示,冷坩埚熔炼时,电磁场频率和冷坩埚结构决定坩埚的透磁能力,随频率上升,坩埚内磁通密度下降,且频率高于100kHz时下降趋势加大;其次,冷坩埚的分瓣结构使其涡流损耗降低,且磁场频率越高效果越明显。对100kHz以上的超高频磁场,坩埚应分割为(16~20)瓣;对(10~100)kHz的高频磁场,坩埚可分割为(8~12)瓣;而对低于10kHz的中高频磁场,坩埚只需分割(4~8)瓣。再者,熔体的磁悬浮力与感应圈电流成平方关系,且电磁场频率越高则磁悬浮力越大。     

一种超导重力仪磁悬浮力的等效计算

为实现超导重力仪磁悬浮力的精确计算,以GWR型超导重力仪为模型基础,采用有限元的思想,将超导球表面电流理想化为多个等高共轴电流环,计算出各个电流环与超导线圈的作用力,求和得到线圈与超导球间的磁悬浮力。利用MATLAB完成计算程序实现,通过改变下线圈电流和上、下线圈电流比,获得满足一定条件的磁悬浮力及其梯度。选取合适的模型参数,计算出线圈对质量为m=4.069 g超导球的磁悬浮力大小为:Ftotal=3.988×10^-2N,磁悬浮力梯度为:-9.699×10^-3N/m,此时悬浮力梯度合适,满足系统稳定性和灵敏度的要求。     

Multi-objective optimization of gradient coil for benchtop magnetic resonance imaging system with high-resolution

Significant high magnetic gradient field strength is essential to obtaining high-resolution images in a benchtop mag- netic resonance imaging （BT-MRI） system with permanent magnet. Extending minimum wire spacing and maximum wire width of gradient coils is one of the key solutions to minimize the maximum current density so as to reduce the local heating and generate higher magnetic field gradient strength. However, maximum current density is hard to optimize together with field linearity, stored magnetic energy, and power dissipation by the traditional target field method. In this paper, a new multi-objective method is proposed to optimize the maximum current density, field linearity, stored magnetic energy, and power dissipation in MRI gradient coils. The simulation and experimental results show that the minimum wire spacings are improved by 159% and 62% for the transverse and longitudinal gradient coil respectively. The maximum wire width increases from 0.5 mm to 1.5 mm. Maximum gradient field strengths of 157 mT/m and 405 mT/m for transverse and lon- gitudinal coil are achieved, respectively. The experimental results in BT-MRI instrument demonstrate that the MRI images with in-plane resolution of 50 ~tm can be obtained by using the designed coils.     

平板型感应耦合等离子体源的线圈配置对功率耦合效率的影响

基于感应耦合等离子体的变压器模型，分析了感应耦合等离子体的功率耦合效率与线圈配置(几何尺寸、电学参量)及等离子体基本参量(等离子体电子密度、电子-中性粒子有效碰撞频率)之间的关系；然后，改变平板型线圈的匝数从而改变了线圈的几何尺寸、电学参量，并且测量出了不同的线圈所对应的功率耦合效率.实验结果表明，线圈的电感量是能否实现放电的决定性因素；而功率耦合效率则与感应线圈的Q值、放电参量(气压、功率)等密切相关，射频输入功率的增加、放电气压的上升都会导致感应耦合等离子体耦合效率的提高，这与感应耦合等离子体的变压器模型预测结果是符合的. 然而，变压器模型给出的提高线圈Q值可导致耦合效率增强的预测结果仅适用于同等电感量的线圈条件. 本文对于单线圈的感应耦合等离子体源的研究为线圈的优化设计甚至大面积的多线圈感应耦合等离子体源研制提供了理论依据. 关键词： 感应耦合等离子体 功率耦合效率 变压器模型     

HL-2M环向场线圈电磁场和受力的计算分析

在建的HL-2M装置的环向场线圈采用了比特板式结构,介绍了采用封闭多边形电流丝模型计算分析HL-2M装置环向场线圈电磁场和纹波情况;环向场线圈电流与环向场引起的电磁力以及与极向场产生的倾覆力也做了计算。计算结果对环向场线圈的设计具有一定的参考意义。     

HL-2M������Ȧ��ų��������ļ������

在建的HL-2M装置的环向场线圈采用了比特板式结构,介绍了采用封闭多边形电流丝模型计算分析HL-2M装置环向场线圈电磁场和纹波情况;环向场线圈电流与环向场引起的电磁力以及与极向场产生的倾覆力也做了计算.计算结果对环向场线圈的设计具有一定的参考意义.     

辅助永磁体磁化方式对单畴GdBCO超导块材捕获磁场分布及其磁悬浮力的影响

通过对方形永磁体和方形辅助永磁体在液氮温度下对GdBCO超导体磁化后超导磁悬浮力的测量, 研究了两种组态中方形辅助永磁体对超导体的磁化方式对单畴GdBCO超导块材磁场分布及其磁悬浮力的影响. 结果发现, 方形辅助永磁体的下表面和超导体上表面保持在同一个水平面上, 磁化进程中方形辅助永磁体在GdBCO超导体上表面水平面内沿直径方向的位置x从–15 mm增加到+15 mm时, 超导磁悬浮力大小与超导体的磁化方式有着密切关系(以Z=0.1 mm为例): 1) 当方形辅助永磁体N极垂直向上且场冷后去掉辅助永磁体时, 超导体最大磁悬浮力先从16.7 N增大到23.1 N, 再减小到16.6 N; 2) 当方形辅助永磁体N极垂直向下且场冷后去掉辅助永磁体时, 超导体最大磁悬浮力先从17.7 N减小到7 N, 再增加到17.6 N; 3) 两种组态中最大磁悬浮力不相等, 而且与零场冷下的最大磁悬浮力(17.1 N)也不同. 这些结果说明: 只有通过科学合理地设计超导体和永磁体的组合方式, 才能获得较高的磁场强度, 有效地提高超导体的磁悬浮力特性, 该结果对促进超导体的应用具有重要的指导意义. 关键词： 单畴GdBCO 永磁体 捕获磁场 磁悬浮力     

CFETR CSMC装配误差下的电磁状态研究

中心螺旋管模型线圈是为了积累中心螺线管线圈设计和制造经验而预研的一套混合超导磁体线圈,该线圈由五大模块组成,高场区采用Nb_3Sn线圈,低场区采用NbTi线圈,可以满足紧凑型聚变装置对低纵横比的要求.然而模型线圈各模块结构复杂、尺寸庞大在装配过程中不可避免的存在装配误差,线圈励磁以后产生的非对称磁场和电磁力将分别影响等离子体的旋转和线圈整体的稳定性.为了详细分析装配误差对线圈磁场和电磁力的影响,选取模型线圈在装配过程中可能出现的典型的装配误差,基于电流丝等效模型计算了NbTi线圈偏置以后Nb_3Sn内外线圈上的磁场和电磁力.计算结果表明,由于装配误差,线圈磁场沿环向呈不均匀分布,轴向电磁力合力不为零;轴向和径向装配误差对线圈磁场和电磁力的影响存在明显的差异;电磁力随着装配误差呈线性增长,当线圈装配误差较大时将引发数倍于线圈自重的电磁力;该研究结果可为偏置状态下模型线圈的耦合场分析和线圈模块的装配方案设计优化提供参考.     

25T超导磁体优化中线圈数量影响分析

20 T以上强磁场在高场科学工程中有着不可替代的作用. 电工研究所正在研制一个25 T全超导磁体系统, 包括15 T背景磁场和10 T高温超导内插磁体. 在磁体的设计和优化中, 线圈的数量和种类对于最终优化结果十分关键. 为了研究磁体数量和磁体相关参数的关系, 计算了20 组不同的线圈组合下磁体的优化结果. 优化中除了考虑必要的限制条件以外, 还采用了一种结合局部优化算法和全局优化算法的方法. 通过对比分析发现, 线圈数量和磁体造价之间, 存在一个“V”形的关系. 更进一步地, 本文分析了不同超导体在磁体中应该贡献的最佳磁场, 以及背景磁体统一供电给优化结果带来的影响.     

Analytical solutions of transient pulsed eddy current problem due to elliptical electromagnetic concentrative coils

The electromagnetic concentrative coils are indispensable in the functional magnetic stimulation and have potential applications in nondestructive testing.In this paper,we propose a figure-8-shaped coil being composed of two arbitrary oblique elliptical coils,which can change the electromagnetic concentrative region and the magnitude of eddy current density by changing the elliptical shape and/or spread angle between two elliptical coils.Pulsed current is usually the excitation source in the functional magnetic stimulation,so in this paper we derive the analytical solutions of transient pulsed eddy current field in the time domain due to the elliptical concentrative coil placed in an arbitrary position over a half-infinite plane conductor by making use of the scale-transformation,the Laplace transform and the Fourier transform are used in our derivation.Calculation results of field distributions produced by the figure-8-shaped elliptical coil show some behaviours as follows:1) the eddy currents are focused on the conductor under the geometric symmetric centre of figure-8-shaped coil;2) the greater the scale factor of ellipse is,the higher the eddy current density is and the wider the concentrative area of eddy current along y axis is;3) the maximum magnitude of eddy current density increases with the increase of spread angle.When spread angle is 180,there are two additional reverse concentrative areas on both sides of x axis.     

一种用于开放式MRI的射频发射线圈设计

介绍了一种用于开放式MRI系统的射频发射线圈. 此发射线圈为上下2个相同的线圈,分别安装在磁体的2极,两线圈采用非对称的正交方式放置. 线圈为矩形螺线管结构,通过电磁场数值计算的方法对线圈的匝间距进行了优化,使线圈在300 mm的球形区域内达到偏差不超过3 dB的均匀性要求. 根据优化结果制作了一套用于0.23 T开放式MRI系统的发射线圈,并对线圈的均匀性及射频发射的效率进行了测试. 测试结果表明,线圈具有较高的发射效率和较好的均匀性,由此验证了设计方案的可行性.     

An Efficacious Target-Field Approach to Design Shim Coils for Halbach Magnet of Mobile NMR Sensors

The main magnetic fields of mobile nuclear magnetic resonance (NMR) magnets differ from those of conventional NMR and magnetic resonance imaging (MRI) magnets. In the Halbach magnet, the main field B ₀ is perpendicular to the longitudinal axis, the symmetry of the current distribution with respect to the symmetry of the magnetic field differs from that in conventional target-field applications, and the current distribution on the coil surface cannot be expressed in terms of periodic basis functions. To obtain the winding pattern of the coil, an efficacious target-field approach. The surface of a coil is divided into small discrete elements, where each element is represented by a magnetic dipole. From the stream function of the elements, the resultant magnetic field is calculated. The optimization strategy follows an objective function defined by the power dissipation or efficiency of the coil. This leads to the optimum stream function on the coil surface, whose contour lines define the winding patterns of the coil. This paper shows winding patterns designed of shim coils for Halbach magnet and illustrates the craft of a shim coil using flexible printed circuit board. The performance of the coils is verified by simulating the fields they produce over the sensitive volume.     

改进型Helmholtz线圈及其磁场均匀性的分析

提出将Helmholtz线圈改为3个同半径的串联线圈,以得到改进型的Helmholtz线圈,经计算得到了改进型Helmholtz线圈磁场的简单公式,对公式的分析表明：改进型Helmholtz线圈的均匀磁场区比一般Helmholtz线圈大得多。     

HL-2M 主机抗扭转支撑结构计算分析

根据通电的环向场(TF)线圈在磁场作用下将产生侧向力和径向力,提出了抗扭转支撑结构方案。该方案能够降低这两种力对 TF 线圈的影响,并且保证线圈连接面的紧密接触和绝缘层不会发生相对错动。对抗扭转支撑结构进行计算分析,确定该结构的受力方式以及传力路径。结果表明,在实验运行以及极端工况下结构的应力、位移能够到达设计要求,通过疲劳计算得出抗扭转支撑结构能满足 20 年以上的实验运行,能够保证 HL-2M装置安全、平稳和可靠的运行。      

Multiple Parallel Round Leg Design for Quadrature Birdcage Coil in Ultrahigh-Field MRI

Copper foil has been widely employed in conventional radio frequency (RF) birdcage coils for magnetic resonance imaging (MRI). However, for ultrahigh-field (UHF) MRI, current density distribution on the copper foil is concentrated on the surface and the edge due to proximity effect. This increases the effective resistance and distorts the circumferential sinusoidal current distribution on the birdcage coils, resulting in low signal-to-noise ratio (SNR) and inhomogeneous distribution of RF magnetic (B₁) field. In this context, multiple parallel round wires were proposed as legs of a birdcage coil to optimize current density distribution and to improve the SNR and the B₁ field homogeneity. The design was compared with three conventional birdcage coils with different width flat strip surface legs for a 9.4 T (T) MRI system, e.g., narrow-leg birdcage coil (NL), medium-leg birdcage coil (ML), broad-leg birdcage coil (BL) and the multiple parallel round wire-leg birdcage coil (WL). Studies were carried out in in vitro saline phantom as well as in vivo mouse brain. WL showed higher coil quality factor Q and more homogeneous B₁ field distribution compared to the other three conventional birdcage coils. Furthermore, WL showed 12, 10 and 13% SNR increase, respectively, compared to NL, ML and BL. It was proposed that conductor’s shape optimization could be an effective approach to improve RF coil performance for UHF MRI.     

基于反串接线圈的金属熔球磁悬浮感应加热数值分析

对金属熔球在反串接线圈中电磁感应加热的电磁场和温度场进行建模.分析安培力在金属熔球上的分布;分析反串接线圈的几何尺寸、电源参数、熔球位置等对金属熔球所受电磁力和所产生焦耳热的影响;给出金属材料的物性参数对金属熔球所受电磁力、产生的焦耳热和金属熔球内部温度场分布的影响.模拟结果与实验观察相吻合.     

New approaches on application of multipole moments for determination of toroidal plasma shift

An application of multipole moments for the determination of toroidal plasma column shift is presented. First, we present analytical details for using this technique. Then, the principle of different models based on this technique for design and fabrication of a six coils will be presented: four modified Rogowski coils (two cosine coils and two sine coils) and two saddle coils (saddle sine coil and saddle cosine coil). As continuous measurements of magnetic field distribution around the toroidal plasma can be made using these coils, this technique is a good method for the determination of toroidal plasma column shift.     

气体物理性质对近场超声悬浮特性的影响研究

在利用近场超声悬浮技术搬运晶圆的过程中,为提高近场超声悬浮力,该文研究了气体物理性质与近场超声悬浮力之间的关系。利用声辐射压理论与流体力学理论对不同气体介质下的悬浮力进行建模与求解。搭建了可测量不同气体环境中悬浮力的实验平台。实验发现氩气环境下超声悬浮力平均值相对空气环境下提升24.8%。结合实验与理论计算分析了气体密度、比热容比、声速与动力黏度对悬浮力的影响,推断气体的比热容比为影响近场超声悬浮力的主要参数。该方法为晶圆搬运的环境适用性提供了参考价值。