Lamb wave propagation in magnetoelectroelastic plates

Based on the three-dimensional linear elastic equations and magnetoelectroelastic constitutive relations, propagation of symmetric and antisymmetric Lamb waves in an infinite magnetoelectroelastic plate is investigated. The coupled differential equations of motion are solved, and the phase velocity equations of symmetric and antisymmetric modes are obtained for both electrically and magnetically open and shorted cases. The dispersive characteristic of wave propogation is explored. The mechanical, electric and magnetic responses of the lowest symmetric and antisymmetric Lamb wave modes are discussed in detailed. Obtained results are valuable for the analysis and design of broadband magnetoelectric transducer using composite materials.     

套管中模式波的响应特征*

在固井质量评价中主要利用套管中模式波的幅度或衰减变化反映水泥的胶结状况,不同测井仪器在套管中激发的模式波的类型不同,研究套管中各模式波的传播特征和影响因素可充分挖掘测量数据的潜在应用价值。CBL和SBT等测井仪器在套管中主要激发拉伸波,类同于平板中的零阶对称Lamb波,水泥环封隔测井仪器的斜入射模式在套管中主要激发套管弯曲波,类同于平板中的零阶反对称Lamb波,垂直入射模式激发套管共振波,类同于平板中的高阶对称Lamb波。该文重点分析了这些模式波的衰减特征及其对微环的响应,套管弯曲波在套后耦合轻质水泥时对微环不敏感,但在套后耦合常规水泥或重水泥时,其衰减明显高于胶结良好的状况;拉伸波对微环的存在最为敏感;套管共振波对微环不敏感。     

两侧有固体层负载时板中Lamb波的传播

本文研究了薄板二面有固体导负载时板中Ｌａｍｂ波的传播，从弹性波理论出发并结合应的边界条件，导出板中Ｌａｍｂ波的色散方程，数值计算表示，不管作为自由状态时板中Ｌａｍｂ波相速（板厚取定时）是大于或小于外层固体的声表面波波速，板中对称及反对称模式的Ｌａｍｂ波相速都随着外层固体层厚度增加而变化并且渐近于外层固体的声表面波波速，数值计算又表明，对很薄的板，板中对称及反对称模式的相速均随负载板的厚度呈线性变化     

Normal mode expansion method for laser-generated ultrasonic Lamb waves in orthotropic thin plates

A quantitative theory for modeling the laser-generated transient ultrasonic Lamb waves, which propagates along arbitrary directions in orthotropic plates, is presented by employing an expansion method of generalized Lamb wave modes. The displacement field is expressed by a summation of the symmetric and antisymmetric modes in the surface stress-free orthotropic plate, and therefore the theory is particularly appropriate for waveform analyses of Lamb waves in thin plates because one needs only to evaluate several lower modes. The transient waveforms excited by the thermoelastic expansion and the oil-coating evaporation are analyzed for a transversely isotropic thin plate. The results show that the theory provides a quantitative analysis to characterize anisotropic elastic stiffness properties of orthotropic plates by laser-generated Lamb wave detection.     

Active fiber composites for the generation of Lamb waves

Active fiber composites (AFC) are thin and conformable transducer elements with orthotropic material properties, since they are made of one layer of piezoelectric ceramic fibers. They are suitable for applications in structural health monitoring systems (SHM) with acoustic non-destructive testing methods (NDT). In the presented work the transfer behavior of an AFC as an emitter of transient elastic waves in plate-like structures is investigated. The wave field emitted by an AFC surface bonded on an isotropic plate was simulated with the finite-difference method. The model includes the piezoelectric element and the plate and allows the simulation of the elastic wave propagation. For comparison with the model experiments using a laser interferometer for non-contact measurements of particle velocities at different points around the AFC on the surface of the plate were performed. Transfer functions defined as the ratio of the electric voltage excitation signal and the resulting surface velocity at a specific point are separately determined for the two fundamental Lamb wave modes. In order to take the orthotropic behavior of the AFC into account the transfer functions are determined for several points around the AFC. Results show that the AFC is capable to excite the fundamental symmetric and antisymmetric Lamb wave mode. The antisymmetric mode is mainly radiated in the direction of the piezoelectric fibers, while the symmetric mode is spread over a larger angle. The amplitudes of the emitted waves depend on the frequency of the excitation as well as on the geometric dimensions of the transducer.     

Generalized thermoelastic Lamb waves in a plate bordered with layers of inviscid liquid

The propagation of thermoelastic waves in a homogeneous isotropic, thermally conducting plate bordered with layers of inviscid liquid or half-space of inviscid liquid on both sides is investigated in the context of generalized theories of thermoelasticity. Secular equations for the plate in closed form and isolated mathematical conditions for symmetric and antisymmetric wave modes in completely separate terms are derived. The results for coupled and uncoupled theories of thermoelasticity have been obtained as particular cases. The different regions of secular equations are obtained and special cases, such as Lame modes, thin plate waves and short wavelength waves of the secular equations are also discussed. The secular equations for thermoelastic leaky Lamb waves are also obtained and deduced. The amplitudes of displacement components and temperature change have also been computed and studied. Finally, the numerical solution is carried out for an aluminum-epoxy composite and aluminum materials plate bordered with water. The dispersion curves for symmetric and antisymmetric thermoelastic wave modes and amplitudes of displacement and temperature change in case of fundamental symmetric (S₀) and skew symmetric (A₀) modes are presented in order to illustrate and compare the theoretical results. The theory and numerical computations are found to be in close agreement. The results have been deduced and compared with the relevant publications available in the literature at the relevant stages of the work.     

Mode selection of Lamb waves for the evaluation of solid plates with liquid loading

This paper studies the mode selection of Lamb waves for evaluating solid plates with liquid loading. For this purpose, the Lamb wave selected should have the features such as zero normal displacement components at the plate surface in contact with liquid, small dispersion, and maximum group velocity. It is found that when the phase velocity of Lamb wave is equal to the longitudinal wave velocity of the plate material, its normal displacement at the plate surface is always zero. Through the numerical analyses, the specific S₂ Lamb wave that has zero normal displacement component at the plate surface, small dispersion and maximum group velocity compared with the other Lamb waves has been found. With respect to the specific S₂ Lamb wave, some experimental examinations have been carried out. It is found that the liquid loading on the plate surface has less influence on the specific S₂ Lamb wave signal but it can effectively eliminate the other signals. Moreover, the specific S₂ Lamb wave selected exhibits the capability of detecting multiple defects in the solid plate with the liquid loading. It can be concluded that the specific S₂ Lamb wave selected is suitable for the evaluation of solid plates with liquid loading.     

用于储罐底板缺陷检测的超声兰姆波模式研究

从超声兰姆波的声场方程出发,得到板材表面离面位移(法向位移)为零的条件,即当超声兰姆波的相速度等于板材介质的纵波声速时,在板材表面的离面位移为零。在给定适当频厚积的条件下,分别数值模拟了仅有切向位移而无离面位移的A1、S1、A2和S2兰姆波模式在有液体负载的单层钢板中的传播情形。结果表明:离面位移为零的S2模式频散较小且对板中缺陷更为敏感。     

复合兰姆波声子晶体中超宽部分禁带

兰姆波在声子晶体薄板中的传播特性因其在无损检测、 减振技术和传感器件等领域的潜在应用价值而受到越来越多的关注. 本文采用超原胞平面波展开法和有限元法系统地研究了复合对称结构声子晶体薄板中的兰姆波超宽部分禁带. 结果表明: 对于在薄板侧面对称地嵌入双层矩形空气柱构成的复杂系统, 低阶兰姆波部分带隙结构极为丰富. 将晶格常数(L)和板厚(H) 比值具有匹配关系的兰姆波声子晶体衔接构成复合结构, 低阶兰姆波部分禁带宽度因各组分结构的部分禁带交叠而得到显著拓宽, 可在低频超宽频带内实现对特定低阶兰姆波模式良好的模式选择功能. 该研究结果对兰姆波缺陷无损检测中模式优化选择及兰姆波单向导通器件设计等方面具有重要意义.     

Modulation instability of wave packets in the presence of linear and nonlinear mode coupling

Conditions for modulation instability of a wave packet consisting of two codirected linearly coupled waves propagating in a light guide with Kerr-type nonlinearity are formulated. The development of the instability with regard to light guide parameters, linear and nonlinear mode coupling, and input power is analyzed for symmetric and antisymmetric light guide excitations. Unlike in single-mode light guides, here modulation instability may arise in the frequency ranges of normal material dispersion and at the zero perturbation frequency.     

Piezoelectric transducer parameter selection for exciting a single mode from multiple modes of Lamb waves

Excitation and propagation of Lamb waves by using rectangular and circular piezoelectric transducers surface-bonded to an isotropic plate are investigated in this work. Analytical stain wave solutions are derived for the two transducer shapes, giving the responses of these transducers in Lamb wave fields. The analytical study is supported by a numerical simulation using the finite element method. Symmetric and antisymmetric components in the wave propagation responses are inspected in detail with respect to test parameters such as the transducer geometry, the length and the excitation frequency. By placing only one piezoelectric transducer on the top or the bottom surface of the plate and weakening the strength of one mode while enhancing the strength of the other modes to find the centre frequency, with which the peak wave amplitude ratio between the S0 and A0 modes is maximum, a single mode excitation from the multiple modes of the Lamb waves can be achieved approximately. Experimental data are presented to show the validity of the analyses. The results are used to optimize the Lamb wave detection system.     

Maxima and minima of the displacement components for the Lamb modes

This paper revisits the vanishing of the transverse component of the particle displacement vector in free surfaces of an isotropic homogeneous plate, for both symmetric and antisymmetric Lamb waves. Drawing on well-known analytical expressions from Viktorov's book [(1967) Rayleigh and Lamb Waves: Physical Theory Applications, Chap. II, pp. 67-121], two distinct frequency-thickness product expressions, in cases where this vanishing occurs, are derived: one for the symmetric modes and another for the antisymmetric modes. At these frequency-thickness products, phase and group velocities have appreciable values which are discussed herein. It appears that these velocities depend on the transverse bulk wave velocity only. This is the specific condition of the Lame? modes. Moreover, theoretical and experimental investigations of displacements in the surface of a plate in air have been carried out. The theoretical part shows that the normal and transverse displacements have, respectively, a local maximum and a local minimum in the vicinity of these frequency-thickness products. The experimental part corroborates the presence of the local maximum of the S(0) Lamb mode for various materials.     

Symmetric and Anti-Symmetric Lamb Waves in a Two-Dimensional Phononic Crystal Plate

It is weft known that Lamb waves in a plate with a mirror plane can be separated into two uncoupled sets： symmetric and anti-symmetric modes. Based on this property, we present a revised plane wave expansion method （PWE） to calculate the band structure of a phononie crystal （PC） plate with a mirror plane. The developed PWE method can be used to calculate the band structure of symmetric and anti-symmetric modes separately, by which the depending relationship between the partial acoustic band gap （PABG）, which belongs to the symmetric and anti-symmetric modes alternatively, and the position of the scatterers can be determined. As an example of its application, the band structure of the Lamb modes in a two-dimensional PC plate with two layers of void circular inclusions is investigated. The results show that the band structure for the symmetric and anti-symmetric modes can be changed by the position of the scatterers drastically, and larger PABGs will be opened when the scatterers are inserted into the area of the plate, where the elastic potential energy is concentrated.     

Liquid level sensor using ultrasonic Lamb waves

This paper describes a novel, noninvasive method for measurement of liquid level in closed metal tanks that are under high pressure. It is based on the use of ultrasonic Lamb waves propagating along the tank wall. Contact with liquid substantially changes the characteristics of these waves and this can be used as an indicator of liquid presence. Theoretical analysis shows that the symmetric and antisymmetric Lamb wave modes, both fundamental and higher order, are sensitive to presence of the liquid. The optimal wave frequency depends on the thickness of the tank wall and wall material. A prototype level sensor based on this principle has been developed. It uses two pairs of wedge transducers to generate and detect Lamb waves propagating along the circumference of the gas tank. An operating frequency of 100 kHz is found to be optimal for use with tanks having a wall thickness of 30-50 mm. Prototype sensors developed under this program have been used successfully in oil fields in the far northern region of Russia.     

An oscillator using high order Lamb wave modes

An oscillator using high order Lamb wave modes is presented. Due to the multimode property of Lamb waves, high frequency oscillators using high order mode Lamb waves can be fabricated. To select the operating mode of the Lamb wave oscillator, a high order mode selector is inserted into the feedback loop. An oscillator using the 13th antisymmetric mode (a₁₃) in Lamb wave is achieved in experiments and the oscillating frequency is 5.30 times higher than that of the a₀ mode excited by the interdigital transducer.     

Damage detection in composite panels based on mode-converted Lamb waves sensed using 3D laser scanning vibrometer

This paper introduces damage identification approach based on guided ultrasonic waves and 3D laser Doppler vibrometry. The method is based on the fact that the symmetric and antisymmetric Lamb wave modes differ in amplitude of the in-plane and out-of-plane vibrations. Moreover, the modes differ also in group velocities and normally they are well separated in time. For a given time window both modes can occur simultaneously only close to the wave source or to a defect that leads to mode conversion. By making the comparison between the in-plane and out-of-plane wave vector components the detection of mode conversion is possible, allowing for superior and reliable damage detection. Experimental verification of the proposed damage identification procedure is performed on fuel tank elements of Reusable Launch Vehicles designed for space exploration. Lamb waves are excited using low-profile, surface-bonded piezoceramic transducers and 3D scanning laser Doppler vibrometer is used to characterize the Lamb wave propagation field. The paper presents theoretical background of the proposed damage identification technique as well as experimental arrangements and results.     

Acoustic waves propagating in a fluid-filled spherical shell placed in a liquid

Acoustic waves arising in a fluid-filled elastic spherical shell placed in a liquid are considered. It is demonstrated that, in general, none of the four types of waves possible in such a system (subsonic and supersonic antisymmetric Lamb waves, symmetric Lamb waves, and whispering galleries) is realized separately, but an interaction between the waves of different types takes place.     

Lamb wave radiation from plate termination in a liquid

The liquid wedge method is used to excite leaky Lamb waves on an aluminium plate while the plate is immersed in water. The excitation occurs near the end of the plate so that sonic energy of the excited mode radiates into the liquid. A Schlieren method is used to observe the radiation pattern and a correlation is made between the radiation lobe structure and the symmetric or antisymmetric nature of the excited mode. Theoretical calculations of the transfer of energy from the plate to the liquid are made and agreement between theory and experiment is obtained.     

Visual characteristics of inhomogeneous acoustic waves

Experimentally obtained visualizations of propagating inhomogeneous acoustic waves driven by zero-order antisymmetric Lamb waves (flexural waves) in water are presented. The inhomogeneous waves are visualized by optical holographic interferometry. A series of photographs show the evolution in time of instantaneous acoustic pressure distributions associated with propagating inhomogeneous waves. The photographs reveal characteristic features of flexurally driven inhomogeneous waves such as transversely attenuated wavefronts oriented perpendicularly to the plate boundary and a phase propagation velocity along the boundary approximately equal to the plate wave velocity (250 meters/second). Effects due to the dispersive nature of the flexural plate waves are also noted in the photographic series. Features distinguishing these subsonic, inhomogeneous surface waves (also called trapped or evanescent waves) from the leaky, lateral or head wave and also from incompressible fluid motions associated with low frequency vibrations of fluid loaded plates are identified. The relevance of inhomogeneous acoustic waves driven by subsonic flexural waves to practical sound-structure interaction problems is discussed.     

An experimental study of the characteristics of the acoustic field of zero normal plate modes

The sources of systematic errors in measuring the amplitude and propagation velocity of normal waves are analyzed. Criteria are proposed for estimating the distances beyond which a wave can be considered a normal wave. The measurement method and corresponding experimental setup are described. Experimental estimates are obtained for the distances necessary for the formation of symmetric zero modes of horizontally polarized normal waves and Lamb waves in thin strips at frequencies of 1.8 and 2.5 MHz.