O2流量对磁控溅射N掺杂TiO2薄膜成分及晶体结构的影响

利用直流脉冲磁控溅射方法在室温下通过改变O₂流量制备具有不同晶体结构的N掺杂TiO₂薄膜,利用台阶仪、X射线光电子能谱仪、X射线衍射仪、紫外-可见分光光度计等设备对薄膜沉积速率、化学成分、晶体结构、禁带宽度等进行分析.结果表明:所制备的薄膜元素配比约为TiO_1.68±0.06N_0.11±0.01,N为替位掺杂,所有样品退火前后均未形成Ti—N相结构,N掺杂TiO₂薄膜的沉积速率、晶体结构等主要依赖于O₂流量.在O₂流量为2 sccm时,N掺杂TiO₂薄膜沉积速率相对较高,薄膜为非晶态结构,但薄膜内含有锐钛矿(anatase)和金红石(rutile)相晶核,退火后薄膜呈anatase和rutile相混合结构,禁带宽度仅为2.86 eV.随着O₂流量的增加,薄膜沉积速率单调下降,退火后样品禁带宽度逐渐增加.当O₂流量为12 sccm时,薄膜为anatase相择优生长,退火后呈anatase相结构,禁带宽度为3.2 eV.综合本实验的分析结果,要在室温条件下制备晶态N掺杂TiO₂薄膜,需在高O₂流量(＞10 sccn)条件下制备. 关键词： 2薄膜')" href="#">N掺杂TiO₂薄膜 磁控溅射 化学配比 晶体结构     

纳米ZnO和ZnO-SiO2复合薄膜的光学性质研究

通过溶胶凝胶(sol-gel)法分别在玻璃衬底上制备了ZnO纳米薄膜和ZnO-SiO₂纳米复合薄膜,并利用紫外-可见光分光光度计对薄膜的光学性能进行了分析.可见光-紫外透射谱显示,随着ZnO溶胶浓度从0.7mol/L降低到0.006mol/L,制备的ZnO薄膜从只出现一个380nm(对应的光学禁带宽度为3.27eV)左右的吸收边到在380和320nm(对应的光学禁带宽度为3.76eV)左右各出现一个吸收边,并且随着ZnO溶胶浓度的降低,在380—320nm波段内的透过率明显提高.而Z 关键词： 纳米ZnO 2复合薄膜')" href="#">ZnO-SiO₂复合薄膜 溶胶凝胶法 透射率     

火焰喷雾法合成ZnO和MgxZn1－xO纳米颗粒的光学性能研究

利用火焰喷雾法成功制备了纳米级的ZnO和Mg_xZn_1-xO颗粒. 通过对样品的X射线衍射谱和场发射扫描电子显微镜照片分析，发现制备的颗粒大小较为均匀，直径在20nm左右；镁元素的掺入引起晶格常数变小. 通过透射光谱和光致发光谱的测量，发现Mg_xZn_1-xO颗粒的禁带宽度远大于ZnO颗粒的禁带宽度，同时对两组样品的紫外发光和可见发光的强度变化和发光机理进行了探讨. 关键词： 火焰喷雾 ZnO 禁带宽度 纳米颗粒     

Co掺杂ZnO薄膜的局域结构和电荷转移特性研究

采用磁束缚电感耦合等离子体溅射沉积法在不同的氧气分压下制备了Zn_0.95Co_0.05O和Zn_0.94Co_0.05Al_0.01O薄膜.利用X射线吸收精细结构技术对薄膜O-K,Co-K和Co-L边进行了局域结构研究,结果表明：Co²⁺取代了四配位晶体场中的Zn²⁺而未改变ZnO的六方纤锌矿结构,高真空条件下制备的薄膜 关键词： Co掺杂ZnO 稀磁半导体 X射线吸收精细结构 共振非弹性X射线散射     

Mn掺杂ZnO光学特性的第一性原理计算

采用基于密度泛函理论(DFT)的第一性原理平面波超软赝势方法计算了纤锌矿ZnO及不同量Mn 掺杂ZnO 晶体的电子结构,分析了掺杂对ZnO 晶体的能带结构、电子态密度、差分电荷分布的影响. 计算结果表明,随着Mn 掺杂含量的增加,ZnO 禁带宽度相应增加并且对紫外吸收区的光吸收能力也随之增强. 关键词： 密度泛函理论(DFT) 第一性原理 超软赝势 Mn掺杂ZnO     

花状掺杂W-VO$lt;sub$gt;2$lt;/sub$gt;/ZnO热致变色纳米复合薄膜研究

为解决掺杂引起的二氧化钒薄膜的红外调制幅度下降以及二氧化钒复合薄膜相变温度需要进一步降低等问题, 采用纳米结构、掺杂改性和复合结构等多种机理协同作用的方案, 利用共溅射氧化法, 先在石英玻璃上制备高(002)取向的ZnO薄膜, 再在ZnO层上室温共溅射沉积钒钨金属薄膜, 最后经热氧化处理获得双层钨掺杂W-VO₂/ZnO纳米复合薄膜. 利用X射线衍射、X射线光电子能谱、扫描电镜和变温光谱分析等对薄膜的结构、组分、形貌和光学特性进行了分析. 结果显示, W-VO₂/ZnO 纳米复合薄膜呈花状结构, 取向性提高, 在保持掺杂薄膜相变温度(约39 ℃)和热滞回线宽度(约6 ℃)较低的情况下, 其相变前后的红外透过率差量增加近2倍, 热致变色性能得到协同增强. 关键词： 2')" href="#">VO₂ ZnO W掺杂 热致变色     

利用脉冲激光沉积法制备高Mg掺杂的六方相MgZnO薄膜

选用Mg0.2Zn0.8O陶瓷靶,利用脉冲激光沉积(PLD)法,在单晶Si(100)和石英衬底上生长了一系列MgZnO薄膜(MZO)。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能谱(EDS)和紫外可见光透射光谱(UV-Vis)等实验手段,研究了在不同工作压强下生长的薄膜样品的晶体结构、微观形貌和光学性能的变化。结果表明:所有的薄膜样品都是单一的ZnO六方相,禁带宽度随生长压强的升高而增加,变化范围在3.83～4.05eV之间,最短吸收边接近300nm。     

掺AlZnO纳米线阵列的光致发光特性研究

采用化学气相沉积方法，以金做催化剂，在Si (100)衬底上制备了掺AlZnO纳米线阵列.扫描电子显微镜(SEM)表征发现ZnO纳米线的直径在30nm左右.X射线衍射(XRD)图谱上只存在ZnO的(002)衍射峰，说明ZnO纳米线沿c轴择优取向.掺AlZnO纳米线阵列的室温光致发光(PL)谱中出现了3个带边激子发射峰：373nm，375nm，389nm.运用激子理论推算出掺AlZnO纳米线的禁带宽度为3.343eV ，束缚激子结合能为0.156eV；纯ZnO纳米线阵列PL谱中3个带边激子发射 关键词： 光致发光 化学气相沉积(CVD) 激子 ZnO纳米线阵列     

生长温度对磁控溅射ZnO薄膜的结晶特性和光学性能的影响

采用反应射频磁控溅射方法，在Si (100) 基片上制备了具有高c轴择优取向的ZnO薄膜.利用 原子力显微镜、透射电子显微镜、X射线衍射分析、拉曼光谱等表征技术，研究了沉积温度 对ZnO薄膜的表面形貌、晶粒尺度、应力状态等结晶性能的影响；通过沉积温度对透射光谱 和光致荧光光谱的影响，探讨了ZnO薄膜的结晶特性与光学性能之间的关系.研究结果显示， 在室温至500℃的范围内，ZnO薄膜的晶粒尺寸随沉积温度的增加而增加，在沉积温度为500 ℃时达到最大；当沉积温度为750℃时，ZnO薄膜的晶粒尺度有所减小；在室温至750℃的范 围内，薄膜中ZnO晶粒与Si基体之间均存在着相对固定的外延关系；在沉积温度低于500℃时 ，制备的ZnO薄膜处于压应变状态，而750℃时沉积的薄膜表现为张应变状态.沉积温度的不 同导致ZnO薄膜的折射率、消光系数、光学禁带宽度以及光致荧光特性的变化，沉积温度对 紫外光致荧光特性起着决定性的作用.此外，探讨了影响薄膜近紫外光致荧光发射的可能因 素. 关键词： ZnO薄膜 表面形貌 微观结构 光学常数     

ZnO/SiO2 复合薄膜的光学性能

采用溶胶-凝胶法在玻璃衬底上制备ZnO/SiO₂复合薄膜,分别用XRD、TEM、SEM对样品的结构和形貌进行表征,并研究了不同ZnO含量对复合薄膜透过率及荧光特性的影响。结果表明,样品经500 ℃退火处理生成了SiO₂和ZnO,其晶粒尺寸为18.7 nm,薄膜具有双层结构。复合薄膜的透过率随着其中ZnO含量的增加而降低,禁带宽度减小,光学吸收边红移。样品在355 nm波长激发下产生了384 nm的紫外发射峰和440 nm的蓝光发射带,并随ZnO含量的增加而增强,它们分别来自ZnO的电子-空穴复合发光和缺陷发光,及ZnO/SiO₂复合薄膜双层结构的缺陷发光。     

Photoluminescence of ZnO and Mn-Doped ZnO Polycrystalline Films Prepared by Plasma Enhanced Chemical Vapour Deposition

ZnO and Mn-doped ZnO polycrystalline films are prepared by plasma enhanced chemical vapour deposition at low temperature （220℃）, and room-temperature photoluminescence of the films is systematically investigated. Analysis from x-ray diffraction reveals that a11 the prepared films exhibit the wurtzite structure of ZnO, and Mndoping does not induce the second phase in the films. X-ray photoelectron spectroscopy confirms the existence of Mn^2＋ ions in the films rather than metalic Mn or Mn^4＋ ions. The emission efficiency of the ZnO film is found to be dependent strongly on the post-treatment and to degrade with increasing temperature either in air or in nitrogen ambient. However, the enhancement of near band edge （NBE） emission is observed after hydrogenation in ammonia plasma, companied with more defect-related emission. Furthermore, the position of NBE shifts towards to high-energy legion with increasing Mn-doped concentration due to Mn incorporation into ZnO lattice.     

Mn doped ZnO nanostructured thin films prepared by ultrasonic spray pyrolysis method

Mn-doped ZnO thin films with different percentage of Mn content (0, 1, 3 and 5 at.%) and substrate temperature of 350 °C, were deposited by a simple ultrasonic spray pyrolysis method under atmospheric pressure. We have studied the structural and optical properties by using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and ultra-violet visible near infrared (UV–Vis-NIR) spectroscopy. The lattice parameters calculated for the Mn-doped ZnO from XRD pattern were found to be slightly larger than those of the undoped ZnO, which indicate substitution of Mn in ZnO lattice. Compared with the Raman spectra for ZnO pure films, the Mn-doping effect on the spectra is revealed by the presence of additional peak around 524 cm⁻¹ due to Mn incorporation. With increasing Mn doping the optical band gap increases indicating the Burstein–Moss effect.     

Effects of doping concentration on properties of Mn-doped ZnO thin films

This paper reports that the radio frequency magnetron sputtering is used to fabricate ZnO and Mn-doped ZnO thin films on glass substrates at 500~°C. The Mn-doped ZnO thin films present wurtzite structure of ZnO and have a smoother surface, better conductivity but no ferromagnetism. The x-ray photoelectron spectroscopy results show that the binding energy of Mn_2p3 / 2 increases with increasing Mn content slightly, and the state of Mn in the Mn-doped ZnO thin films is divalent. The chemisorbed oxygen in the Mn-doped ZnO thin films increases with increasing Mn doping concentration. The photoluminescence spectra of ZnO and Mn-doped ZnO thin films have a similar ultraviolet emission. The yellow green emissions of 4~wt.% and 10~wt.% Mn-doped thin films are quenched, whereas the yellow green emission occurs because of abundant oxygen vacancies in the Mn-doped ZnO thin films after 20~wt.% Mn doping. Compared with pure ZnO thin film, the bandgap of the Mn-doped ZnO thin films increases with increasing Mn content.     

Mn掺杂ZnO光学特性的第一性原理计算

采用基于密度泛函理论(DFT)的第一性原理平面波超软赝势方法计算了纤锌矿ZnO及不同量Mn 掺杂ZnO 晶体的电子结构，分析了掺杂对ZnO 晶体的能带结构、电子态密度、差分电荷分布的影响. 计算结果表明，随着Mn 掺杂含量的增加，ZnO 禁带宽度相应增加并且对紫外吸收区的光吸收能力也随之增强.     

Quenching of surface traps in Mn doped ZnO thin films for enhanced optical transparency

The structural and photoluminescence analyses were performed on un-doped and Mn doped ZnO thin films grown on Si (1 0 0) substrate by pulsed laser deposition (PLD) and annealed at different post-deposition temperatures (500-800 °C). X-ray diffraction (XRD), employed to study the structural properties, showed an improved crystallinity at elevated temperatures with a consistent decrease in the lattice parameter ‘c’. The peak broadening in XRD spectra and the presence of Mn 2p3/2 peak at ∼640 eV in X-ray Photoelectron Spectroscopic (XPS) spectra of the doped thin films confirmed the successful incorporation of Mn in ZnO host matrix. Extended near band edge emission (NBE) spectra indicated the reduction in the concentration of the intrinsic surface traps in comparison to the doped ones resulting in improved optical transparency. Reduced deep level emission (DLE) spectra in doped thin films with declined PL ratio validated the quenching of the intrinsic surface traps thereby improving the optical transparency and the band gap, essential for optoelectronic and spintronic applications. Furthermore, the formation and uniform distribution of nano-sized grains with improved surface features of Mn-doped ZnO thin films were observed in Field Emission Scanning Electron Microscopy (FESEM) images.     

Room-Temperature Ferromagnetic ZnMnO Thin Films Synthesized by Plasma Enhanced Chemical Vapour Deposition Method

Room-temperature ferromagnetic Mn-doped ZnO films are grown on Si （001） substrates by plasma enhanced chemical vapour deposition （PECVD）. X-ray diffraction measurements reveal that the Znl-xMn.O films have the single-phase wurtzite structure. X-ray photoelectron spectroscopy indicates the existence of Mn^2＋ ions in Mndoped ZnO films. Furthermore, the decreasing additional Raman peak with increasing Mn-doping is considered to relate to the substitution of Mn ions for the Zn ions in ZnO lattice. Superconducting quantum interference device （SQUID） measurements demonstrate that Mn-doped ZnO films have ferromagnetic behaviour at room temperature.     

First-principles study and electronic structures of Mn-doped ultrathin ZnO nanofilms

The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band gaps of ZnO films with 2,4,and 6 layers are larger than the band gap of the bulk with wurtzite structure and decrease with the increase of film thickness.However,the four-layer ZnO nanofilms exhibit ferromagnetic phases for Mn concentrations less than 24% and 12% for Mn-doping performed in the whole layers and two layers of the film respectively,while they exhibit spin glass phases for higher Mn concentrations.It is also found,on the one hand,that the spin glass phase turns into the ferromagnetic one,with the substitution of nitrogen atoms for oxygen atoms,for nitrogen concentrations higher than 16% and 5% for Mn-doping performed in the whole layers and two layers of the film respectively.On the other hand,the spin-glass state is more stable for ZnO bulk containing 5% of Mn impurities,while the ferromagnetic phase is stable by introducing the p-type carriers into the bulk system.Moreover,it is shown that using the effective field theory for ferromagnetic system,the Curie temperature is close to the room temperature for the undamped Ruderman-Kittel-Kasuya-Yoshida(RKKY) interaction.     

基于SSCVD方法的a-b轴取向ZnO薄膜制备

以Zn₄(OH)₂(O₂CCH₃)₆·2H₂O为单一固相有机源,采用单源化学气相沉积法(Single sour cechem icalvapor deposition,SSCVD)在Si(100)衬底上制备ZnO薄膜,用X射线衍射(XRD)、原子力显微镜(AFM)分析ZnO薄膜样品的晶体结构和微观形貌,并用X射线光电子能谱(XPS)对薄膜的锌氧化学计量比进行了分析。研究结果表明:在非平衡条件下所得到的ZnO薄膜沿a-b轴取向生长,基片温度对ZnO薄膜生长过程影响较大,随着基片温度的升高,薄膜呈现c轴生长趋势;晶粒成柱状、尺寸均匀、膜层结构致密;薄膜样品中n_Zn:n_O=0.985。     

Nanostructure and optical properties of M doped ZnO (M=Ni, Mn) thin films prepared by sol-gel process

The transparent thin films of undoped, Mn-doped, and Ni-doped zinc oxide (ZnO) have been deposited on glass substrates via sol-gel technique using zinc acetate dehydrate, nickel chloride, and manganese chloride as precursors. The structural properties and morphologies of the deposited undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/vis spectroscopy. The analyzed results indicate that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn or Ni related phases. The band gap energy was estimated by Tauc's method and found to be 3.28, 3.26, and 3.34 eV for ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films at room temperature, respectively. Room temperature photoluminescence is observed for the ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films.