低阈值单谐振周期极化掺镁铌酸锂光参量振荡器

对基于周期极化掺镁铌酸锂晶体的信号光单谐振光学参量振荡器的输出特性进行了实验研究.讨论了光学参量振荡器谐振腔的腔长、周期极化铌酸锂晶体的通光长度、输出镜的透过率以及抽运光的脉冲宽度对光学参量振荡器谐振阈值的影响.光学参量振荡器的抽运源采用输出波长为1 064 nm的声光调Q Nd∶YVO4激光器,在重复频率为2 kHz、周期极化掺镁铌酸锂晶体的温度为30 ℃的条件下,光学参量振荡器的振荡阈值仅为48 mW.当抽运功率为94 mW时获得了25 mW的信号光输出,其光-光转换效率为26.6%.     

周期极化铌酸锂晶体的红外光谱测量分析

对周期极化非线性品体的光参量振荡器实现连续调谐输出的条件进行了理论模拟和分析,并且针对基于多周期的掺镁铌酸锂晶体光参量振荡器进行了实验研究,在掺镁铌酸锂晶体内制作了6个等间隔的晶畴区,其间距为0.5 μm,极化周期范围为29.0～31.5 μm.在室温下采用LD端面抽运的声光调Q Nd:YVO4激光器作泵浦源,实现了PPMgLN光参量振荡器的信号光在1449.7～1665.0 nm、闲频光在3 989.2～2 946.0 nm范围内的调谐输出,其最低激射阈值为108.0 mW、最高激射阈值为149.2 mW.当泵浦功率为649 mW时,获得了信号光最高为118.5 mW的输出,其光-光转换效率为18.26%;闲频光最高输出为46.6 mW,其光一光转换效率为7.18%.以上参数均接近实用化水平.而且,这两个波段的光源分别在整个光纤通信的S+C+L波段和大气层透射窗口范围,具有十分重要的应用前景.     

周期极化掺镁铌酸锂光学参量振荡器时域特性的实验研究

分别采用MOTORULA公司的硅基光电二极管探测器和JUDSON公司的InGaAs光电二极管探测器对泵浦光和信号光的脉宽进行了测量.研究了极化周期、工作温度以及抽运功率与周期极化掺镁铌酸锂光学参量振荡器输出的信号光脉冲宽度的作用关系.实验采用LD端面抽运的声光调QNd:YVO4激光器作为抽运源,在晶体温度为30℃、极化周期为29.5μm条件下,当抽运功率为1008mW时,获得了平均功率为238mW的信号光输出,其光-光转换效率为23.6%,最窄脉冲宽度约为9.3ns,相对抽运光脉宽被明显压窄.     

周期极化掺镁铌酸锂光学参量振荡器时域特性的实验研究

分别采用MOTORULA公司的硅基光电二极管探测器和JUDSON公司的InGaAs光电二极管探测器对泵浦光和信号光的脉宽进行了测量.研究了极化周期、工作温度以及抽运功率与周期极化掺镁铌酸锂光学参量振荡器输出的信号光脉冲宽度的作用关系.实验采用LD端面抽运的声光调Q Nd∶YVO4激光器作为抽运源,在晶体温度为30 ℃、极化周期为29.5 μm条件下,当抽运功率为1 008 mW时,获得了平均功率为238 mW的信号光输出,其光-光转换效率为23.6%,最窄脉冲宽度约为9.3 ns,相对抽运光脉宽被明显压窄.     

外腔式宽调谐被动调QNd:YVO_4/PPMgLN光学参量振荡器

报道了一个低阈值宽调谐、被动调Q、单谐振掺MgO的周期性极化铌酸锂晶体(PPMgLN)光学参量振荡器。利用被动调Q的Nd:YVO4激光器作为泵浦源,采用外腔结构,在室温下,实现了PPMgLN晶体的准相位匹配光学参量振荡。光参量振荡的阈值仅为0.27W(单脉冲能量4.5μJ、脉宽35ns);在泵浦光为1.35W(脉冲能量8.2μJ、脉宽35ns),PPMgLN周期为31μm时,获得了161.9mW,3.202μm脉冲激光输出;同时获得了98.5mW的1.594μm信号光输出,总的光光转化效率达到19.3%。通过改变晶体的周期,实现了闲频光3.13～4.19μm,信号光1.43～1.65μm的宽带可调谐激光输出。     

高功率,红光至中红外可调谐腔内和频光学参量振荡器

本文利用高重复频率,高平均功率大模场面积飞秒光纤激光器作为同步抽运源,抽运以多周期极化掺氧化镁铌酸锂为非线性晶体的单共振光学参量振荡器,获得了高功率可调谐红光至中红外光,信号光调谐范围为1450—2200 nm,闲频光调谐范围为2250—4000 nm,在2 W的抽运功率下,信号光输出波长为1502 nm时获得最大输出功率374 mW,转换效率为18.7%,脉冲宽度为144 fs,此时中红外输出中心波长为3.4μm,平均功率为166 mW.再利用BBO晶体对信号光进行腔内和频,获得和频光输出波长调谐范围为610—668 nm,在4.1 W抽运的情况下,最高平均功率为615 nm处的694 mW,转换效率达16.9%.     

低阈值温度调谐PPMgLN红外光参量振荡

研究了温度调谐下周期极化镁掺杂铌酸锂晶体的红外光参量振荡特性。采用外电场短脉冲极化技术,在大小为7.0mm×50.0mm×1.0mm的Z切高镁掺杂(摩尔分数0.05)铌酸锂上制备出了准相位匹配光学微结构器件,极化周期为30.0μm。以输出波长为1064nm的声光调QNd:YAG固体激光器作为基频泵浦光开展了光参量振荡研究。实验表明:泵浦该PPMgLN晶体,实现了室温下低阈值红外光参量振荡产生,阈值功率仅为45mW(重复频率1kHz)。在泵浦输入功率为225mW时,有36mW信号光输出,转换效率达到16.0%,通过调谐晶体温度(20~180℃),获得了调谐范围为1503~1550nm波段的OPO信号光,实现了低阈值可调谐红外光的稳定输出。     

高功率宽调谐输出的多周期极化铌酸锂晶体光学参量振荡器

利用掺杂浓度为5 mol%的掺氧化镁多周期极化铌酸锂晶体实现了高效单谐振的准相位匹配光参量振荡器,所使用的周期极化铌酸锂晶体有6个周期,且以1 μm为间隔,从26.5~31.5 μm. 该光参量振荡器以脉宽为150 ns,重复频率为10 kHz的声光调Q Nd∶YAG激光器为泵浦源,且泵浦光波长为1.064 μm. 通过控制晶体的温度（50~200℃）以及改变晶体的极化周期（26.5~31.5 μm）,可由该光参量振荡器获得2.83~2.89 μm,3.10~3.38 μm,3.57~3.78 μm,3.95~4.12 μm, 4.28~4.46 μm,4.65~4.79 μm的闲频光连续调谐输出. 且当泵浦功率为8.15 W时,在闲频光输出波长为3.33 μm处,获得了最大输出功率2.17 W.     

基于镁掺杂的周期性畴反转铌酸锂的宽调谐光参量振荡器

报道基于6mol%镁掺杂的周期性畴反转掺镁铌酸锂(PPMgLN)的宽调谐光参量振荡器(OPO). PPMgLN采用外加电场法制作，周期为27.8—31.6μm，周期间隔为0.2μm.光参量振荡器的抽运源采用输出为1.064μm的声光调Q的Nd³⁺:YVO₄激光器，其调谐范围为1.42—1.73μm(信号光)和2.76—4.27μm(闲散光)，斜率效率达到47%.在输入功率为10.6W时，输出功率达到4.8W(信号光和闲散光之和). 关键词： 周期性畴极化掺镁铌酸锂 宽调谐光参量振荡器     

周期性极化铌酸锂晶体光参量振荡调谐与容差特性分析

研究了周期性极化铌酸锂晶体光参量振荡的工作机理,并讨论了其波长调谐特性与极化反转光栅周期、抽运光波长与晶体温度的关系.在此基础上,通过对相位失配因子求微分的方案,分析了光参量振荡的增益与光栅周期、抽运光波长与晶体温度的关系,以及光栅周期、抽运光波长与晶体温度容差的关系 关键词： 准相位匹配 周期性极化铌酸锂 光参量振荡     

Dye laser pumped, continuous-wave KTP optical parametric oscillators

4 (KTP) optical parametric oscillators (OPOs) with pump and idler resonant cavities. With a linear two-mirror cavity the pump power at threshold was 70 mW. The single-frequency signal and idler output wavelengths were tuned in the range of 1025 to 1040 nm and 1250 to 1380 nm by tuning the dye laser in the range of 565 to 588 nm. With a dual three-mirror cavity the threshold was 135 mW. Pumped by 500 mW of 578 nm radiation the 1040 nm single-frequency signal wave output power was 84 mW. Power and frequency stable operation with a spectral bandwidth of less than 9 MHz was obtained by piezo-electrically locking the length of the pump resonant cavity to the dye laser wavelength. Similar performance was achieved by placing the idler resonant OPO inside the resonator of the dye laser. With this system power stable and single-frequency operation was achieved with a spectral bandwidth of less than 11 MHz for the idler wave. Received: 3 February 1998/Revised version: 9 March 1998     

Near- to mid-infrared picosecond optical parametric oscillator based on periodically poled RbTiOAsO(4)

We describe a Ti:sapphire-pumped picosecond optical parametric oscillator based on periodically poled RbTiOAsO(4) that is broadly tunable in the near to mid infrared. A 4.5-mm single-grating crystal at room temperature in combination with pump wavelength tuning provided access to a continuous-tuning range from 3.35 to 5microm , and a pump power threshold of 90 mW was measured. Average mid-infrared output powers in excess of 100 mW and total output powers of 400 mW in ~1-ps pulses were obtained at 33% extraction efficiency.     

种子注入环形腔人眼安全KTP参变振荡器的研究

利用电光调Q的Nd:YAG激光器抽运非临界相位匹配(θ=90°,φ=0°)环形腔KTP光学参变振荡器(OPO),实现了高能量人眼安全波段的1.57μm激光输出。理论与实验结果表明,减小谐振腔长度和注入种子源激光可以有效降低阈值,提高输出能量。当Nd:YAG激光器抽运能量为88mJ时,注入种子源功率由0mW增加到6mW,输出能量由8.8mJ增加到14mJ。当抽运能量为167.7mJ,注入种子源功率达到6mW时,最大输出能量达到46mJ,峰值功率7.44MW。     

LD抽运Nd:LuVO4微片激光器性能研究

报道了一类新型的LD端面抽运Nd:LuVO4微片激光器,讨论了在不同掺杂浓度,不同厚度和不同透过率下的激光性质,测定了在不同抽运功率下,微片最佳激光输出功率与LD抽运温度的关系.在2W抽运功率下获得923mW的1064nm激光输出,阈值为48mW,斜效率为52%.对微片制冷后斜效率提高到59%.     

双后向结构的线宽拓展L波段超荧光光源

报道了采用两级级联双后向抽运的光源结构,实现高效率和线宽拓展的L波段掺铒光纤超荧光光源.通过数值模拟,研究了两级光纤长度分配和抽运功率比例对光源输出特性的影响.模拟表明,该结构可获得线宽拓展的平坦L波段光谱,相比常规L波段光谱线宽拓展了15 nm,达近60 nm.此外,抽运功率比例为1∶1时该结构的抽运转换效率最高.利...     

激光二极管泵浦的Nd：YVO4单频绿光激光器

对激光二极管泵浦单频连续运行的Ｎｄ：ＹＶＯ４腔内倍频激光器进行了理论和实验研究，通过精密调控Ｎｄ：ＹＶＯ４，ＫＴＰ及泵浦泵温度以达到有关参数的最佳匹配，从而获得了较稳定的单横模，单纵模，单偏振的绿光输出，实测最大单频录光功率为７．５ｍＷ，此时会聚磁浦光功率约为４３０ｍＷ，已超过阈值泵浦功率１３倍以上。     

2.5-GHz repetition-rate singly resonant optical parametric oscillator synchronously pumped by a mode-locked diode oscillator amplifier system

We report on an optical parametric oscillator (OPO) that is synchronously pumped directly by a diode laser. This laser is an actively mode-locked master-oscillator power-amplifier system that produces 20-ps pulses at 927 nm with a repetition rate of 2.5 GHz and an average power of 0.9 W. The OPO, which is a singly resonant device based on periodically poled lithium niobate, generates 7.8-ps pulses. The OPO threshold is 300 mW of average pump power, and the maximum average idler output power is 78 mW at a wavelength of 2100 nm. By changing the crystal temperature we can wavelength tune the output in the ranges 1530-1737 nm (signal) and 1986-2348 nm (idler). Rapid wavelength tuning of the OPO over 46 nm (signal) and 74 nm (idler) is achieved through tuning the cavity length over 28 microm by use of a piezoelectric transducer.     

Generation of Femtosecond Laser Pulse at 1.43 GHz from an Optical Parametric Oscillator Based on LBO Crystal

A femtosecond LBO optical parametric oscillator(OPO) with widely adjustable repetition rate by fractionally decrement of the cavity length is demonstrated. The repetition rate of 755 MHz to 1.43 GHz at an interval of 75.5 MHz is realized, which is 10 to 19 times that of the pump laser. The properties of output signal at 750 nm at different repetition rates are studied. The power of signal decreases with increasing the repetition rate. The maximum power of 194 mW at the repetition rate of 755 MHz and the minimum power of 22 mW at repetition rate of 1.43 GHz for the signal at 750 nm are obtained for the pump power of 3 W.