发光层厚度对联苯乙烯衍生物蓝色有机发光器件性能的影响

本文制备了联苯乙烯衍生物(4, 4'-bis(2, 2'-diphenylvinyl)-1, 1'-biphenyl, DPVBi) 为发光层的蓝色有机电致发光器件. 器件性能随发光层厚度变化而变. 在DPVBi厚度为10---50 nm范围内, 同样电流密度下器件亮度及效率随DPVBi厚度增加先增后减, 40 nm时最佳, 最高亮度达到15840 cd/m², 最高外量子效率达到3.2%, 器件色坐标(Commission Internationale de l'Eclairage (CIE) co-ordinates) 为(0.15, 0.15). DPVBi厚度超过40 nm时器件发光光谱出现红移而致色度变差, 其原因可归于微腔效应所致. 同时, 通过实验结果分析表明DPVBi中激子扩散长度位于20---30 nm范围.     

Screen-printed white OLED based on polystyrene as a host polymer

We demonstrate the use of screen printing in the fabrication of single-layer organic-light-emitting devices (OLEDs). The organic layer is a single-layer of polystyrene, in which we incorporate rubrene for orange emission and α-NPD, DPVBi for blue emission. An appropriate mixing of the two colors produced white emission by incomplete Förster energy transfer. We showed the role of each constituent, α-NPD, DPVBi and rubrene in the emission characteristics of OLEDs. The turn-on voltage of screen-printed white OLEDs was about 10 V with maximum brightness and luminous efficiency up to 1300 cd/m² and 9 cd/A, respectively.     

High efficiency small molecule white organic light-emitting devices with a multilayer structure

In this paper, a new white organic light-emitting device (WOLED) with multilayer structure has been fabricated. The structure of devices is ITO/N, N-bis-(1-naphthyl)-N, N^′-diphenyl-1, 1′-biphenyl-4, 4′-diamine (NPB) (40 nm)/NPB: QAD (1%): DCJTB (1%) (10 nm) /DPVBi (10 nm) /2, 9-dimethyl, 4, 7-diphenyl, 1, 10-phenanthroline (BCP) (d nm)/tris-(8-hydroxyquinoline) aluminium (Alq₃)(50-d nm)/LiF (1 nm)/Al (200 nm). In our devices, a red dye 4-(dicyanomethylene)-2-t-butyl-6 (1, 1, 7, 7-tetramethyl julolidyl-9-enyl)-4H-pyran (DCJTB) and a green dye quinacridone (QAD) were co-doped into NPB. The device with 8 nm BCP shows maximum luminance of 12 852 cd/m² at 20 V. The current efficiency and power efficiency reach 9.37 cd/A at 9 V and 3.60 lm/W at 8 V, respectively. The thickness of the blocking layer permit the tuning of the device spectrum to achieve a balanced white emission with Commission International de’Eclairage (CIE) chromaticity coordinates of (0.33,0.33). The CIE coordinates of device change from (0.3278, 0.3043) at 5 V to (0.3251, 0.2967) at 20 V that are well in the white region, which is largely insensitive to the applied bias.     

Co50Fe50-xSix合金的结构相变和磁性

利用实验测量和理论计算相结合的方法,研究了介于B2结构CoFe低有序合金和L2₁结构Co₂FeSi高有序合金之间的Co₅₀Fe_50-xSi_x合金的结构相变、磁相变、分子磁矩和居里温度.采用考虑Coulomb相互作用的广义梯度近似(GGA+U)方法计算了合金的能带结构.研究发现,合金出现较强的原子有序倾向,表现出较强的共价成相作用.合金的晶格常数、磁矩、居里温度随Si含量的增加而线性地降低,极限成分Co₂FeSi合金的分子磁矩和居里温度分别达到5.92μ_B和777 ℃.原子尺寸效应导致合金晶格发生变化,但并未成为居里温度和分子磁矩变化的主导因素.分子磁矩的变化符合Slater-Pauling原理,但发现原子磁矩的变化并非线性,据此提出了共价成相对磁性影响的观点.采用Stearns理论解释了居里温度的变化趋势,排除了原子间距对居里温度的主导影响作用.能带计算的结果还表明,Co₂FeSi作为半金属材料并非十分完美,可能在实际应用中会出现自旋极化率降低的问题.发现该系列合金的结构相变和磁相变随着成分的变化聚集在窄小的成分和温度范围内. 关键词： 磁性 Heusler合金 结构相变     

Efficient white organic light-emitting devices using 4,7-diphenyl-1,10-phenanthroline as block layer

A white light-emitting device has been fabricated with a structure of ITO/m-MTDATA (45 nm)/NPB (10 nm)/DPVBi (8 nm)/DPVBi:DCJTB 0.5% (15 nm)/BPhen (x nm)/Alq₃ [(55−x) nm]/LiF (1 nm)/Al, with x=0, 4, and 7. BPhen was used as the hole-blocking layer. This results in a mixture of lights from DPVBi molecules (blue-light) and DCJTB (yellow-light) molecules, producing white light emission. The chromaticity can be readily adjusted by only varying the thickness of the BPhen layer. The CIE coordinates of the device are largely insensitive to the driving voltages. When the thickness of BPhen is 7 nm, the device exhibits peak efficiency of 6.87 cd/A (3.59 lm/W) at the applied voltage of 6 V, the maximum external quantum efficiency η_ext=2.07% corresponding to 6.18 cd/A, and the maximum brightness is 18494 cd/m² at 15 V.     

Enhancement of performance for blue organic light emitting devices by utilizing an adjustable chromaticity layer

An adjustable chromaticity layer was successfully applied to a TBADN-based blue organic light-emitting device (BOLED) for improving chromaticity and luminance efficiency. The device was constructed by sandwiching an ultrathin [DPVBi: BCzVB] layer between hole-transport layer and primary emission layer. The optimized device gives the Commission Internationale de I’éclairage (CIE) color coordinates of (0.166, 0.201) at the current density of 20 mA/cm² and a maximum luminance efficiency of 8.43 cd/A at the driving voltage of 11 V.     

Solution-processed white organic light-emitting devices based on small-molecule materials

We investigated solution-processed films of 4,4′-bis(2,2-diphenylvinyl)-1,1′-bibenyl (DPVBi) and its blends with N,N′-bis(3-methylphenyl)-(1,1′-biphenyl)-4,4′-diamine (TPD) by atomic force microscopy (AFM). The AFM result shows that the solution-processed films are pin-free and their morphology is smooth enough to be used in OLEDs. We have developed a solution-processed white organic light-emitting device (WOLEDs) based on small-molecules, in which the light-emitting layer (EML) was formed by spin-coating the solution of small-molecules on top of the solution-processed hole-transporting layer. This WOLEDs, in which the EML consists of co-host (DPVBi and TPD), the blue dopant (4,4′-bis[2-(4-(N,N-diphenylamino)phenyl)vinyl]biphenyl) and the yellow dye (5,6,11,12-tetraphenylnaphtacene), has a current efficiency of 6.0 cd/A at a practical luminance of 1000 cd/m², a maximum luminance of 22500 cd/m², and its color coordinates are quite stable. Our research shows a possible approach to achieve efficient and low-cost small-molecule-based WOLEDs, which avoids the complexities of the co-evaporation process of multiple dopants and host materials in vacuum depositions.     

All-in-one-type organic light-emitting diodes for color tuning using phosphor in glasses with Pb-free silicate powders

We demonstrate all-in-one-type organic light-emitting diodes (OLEDs) that are fabricated using a color converting plate as a substrate. The color converting plate is Pb-free phosphor-in-glass (PiG), which is prepared by mixing Y₃Al₅O₁₂:Ce³⁺ (YAG:Ce³⁺) and SiO₂–B₂O₃–RO (R = Ba, Zn) glass frit by sintering at 750 °C for 30 min. The maximum luminance, luminance efficiency, and power efficiency of blue OLEDs fabricated on commercial glass are measured as 10500 cd/m², 10.18 cd/A, and 2.95 lm/W, respectively. The Commission Internationale de l'Eclairge (CIE) coordinates of blue OLEDs is (0.167, 0.325). Our obtained results show that the luminance value decreased as the PiG thickness increased, and the glass to phosphor (GTP) ratio decreased. The OLED devices fabricated on the PiG substrate (GTP ratio = 9:1, thickness: 150 μm) showed a maximum luminance, luminance efficiency, and power efficiency of 7600 cd/m², 8.76 cd/A, and 2.85 lm/W, respectively. The CIE color coordinates changed to (0.286, 0.504) at 200 mA/cm². These results proved that color coordination can be easily adjusted by varying the GTP ratio and the thickness of the PiG.     

White organic electroluminescence from fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc doped with phosphorescent material

Efficient white electroluminescence has been obtained by using an electroluminescent layer comprising of a blue fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(hpb)₂] doped with red phosphorescent bis (2-(2′-benzothienyl) pyridinato-N,C^3′)iridium(acetylacetonate) [Ir(btp)₂acac] molecules. The color coordinates of the white emission spectrum was controlled by optimizing the concentration of red dopant in the blue fluorescent emissive layer. Organic light-emitting diodes were fabricated in the configuration ITO/α-NPD/Zn(hpb)₂:0.01 wt%Ir(btp)₂acac/BCP/Alq₃/LiF/Al. The J-V-L characteristic of the device shows a turn on voltage of 5 V. The electroluminescence (EL) spectra of the device cover a wide range of visible region of the electromagnetic spectrum with three peaks around 450, 485 and 610 nm. A maximum white luminance of 3500 cd/m² with CIE coordinates of (x, y=0.34, 0.27) at 15 V has been achieved. The maximum current efficiency and power efficiency of the device was 5.2 cd/A and 1.43 lm/W respectively at 11.5 V.     

Effect of thickness variation of hole injection and hole blocking layers on the performance of fluorescent green organic light emitting diodes

In this paper we present the effect of thickness variation of hole injection and hole blocking layers on the performance of fluorescent green organic light emitting diodes (OLEDs). A number of OLED devices have been fabricated with combinations of hole injecting and hole blocking layers of varying thicknesses. Even though hole blocking and hole injection layers have opposite functions, yet there is a particular combination of their thicknesses when they function in conjunction and luminous efficiency and power efficiency are maximized. The optimum thickness of CuPc (Copper(II) phthalocyanine) layer, used as hole injection layer and BCP (2,9 dimethyl-4,7-diphenyl-1,10-phenanthroline) used as hole blocking layer were found to be 18 nm and 10 nm respectively. It is with this delicate adjustment of thicknesses, charge balancing is achieved and luminous efficiency and power efficiency were optimized. The maximum luminous efficiency of 3.82 cd/A at a current density of 24.45 mA/cm² and maximum power efficiency of 2.61 lm/W at a current density of 5.3 mA/cm² were achieved. We obtained luminance of 5993 cd/m² when current density was 140 mA/cm². The EL spectra was obtained for the LEDs and found that it has a peaking at 524 nm of wavelength.     

White organic light-emitting diodes based on benzothiazole derivative

This paper describes the white organic light-emitting diodes (WOLEDs) made from a benzothiazole derivative, N-(4-(benzo[d]thiazol-2-yl)phenyl)-N-phenylnaphthalen-1-amine (BPNA). The bright yellowish-white emission was obtained from a non-doped triple-layer device: ITO/NPB (40 nm)/BPNA (50 nm)/Alq₃ (40 nm)/LiF/Al. The Commission Internationale de L’Eclairage (CIE) coordinates of the device were (0.24, 0.36) at 10 V. The maximum brightness of the device was 9225 cd/m² at 14.4 V. A current efficiency of 3.08 cd/A, a power efficiency of 1.21 lm/W and an external quantum efficiency of 1.18% at a driving current density of 20 mA/cm² were achieved. WOLED with a DCJTB-doped structure of ITO/TcTa/BPNA/BPNA: DCJTB (0.5%)/BPNA/BCP/Alq₃/LiF/Al was fabricated in comparison with the non-doped device. The device emitted bright white light with the CIE coordinates of (0.33, 0.29) at 10 V and a maximum luminance of 7723 cd/m² at 14.8 V.     

Simple-structure white organic light emitting diodes with high color temperature

We present high color temperature white organic light emitting diodes with a simple p-i-n structure. A sky blue phosphorescent dopant of iridium(III) bis[4,6-(difluorophenyl)-pyridinato-N,C^2’] picolinate and a red phosphorescent dopant of bis(2-phenylquinoline)(acetylacetonate)iridium(III) in the emissive layers is employed to make high color temperature devices. Very stable color variation under ?0.02 until a 5000 cd/m² brightness value is realized by efficient carrier control in a multi stacked emitting layer of blue/red/blue colors. Maximum current and power efficiencies of 23.8 cd/A and 22.9 lm/W in forward direction are obtained. With balanced emissions from the two emitters, the white light emission with very high correlated color temperature of 7308 K as well as CIE coordinates of (0.30, 0.33) is achieved.     

Small-molecular white organic light-emitting devices employing 2, 5, 2′, 5′-tetra (<Emphasis Type="Italic">p</Emphasis>-trifluoromethylstyryl)-biphenyl as single-emitting component

We demonstrate a promising single layer white light-emitting device using a dimeric trimeric phenylenvinylene derivative as emitting layer. The broad electroluminescence emission band is composed of blue component from singlet excited state of individual 2, 5, 2′, 5′-tetra (p-trifluoromethylstyryl)-biphenyl molecule and long-wavelength electromer emission in electroluminescence. Therefore, white-light emission can also be obtained with a typical three-layer structure of ITO/NPB (50 nm)/TFM-TSB (50 nm)/Alq₃ (30 nm)/LiF/Al device. The maximum brightness of this device is 809 cd/m² at 217 mA/cm² and 13 V, and the maximum luminous efficiency is 1.49 cd/A at 11 mA/cm² and 8 V.      

芴-咔唑新型共聚物/PVK掺杂体系的电致发光特性研究

研究了新型的芴-咔唑共聚物(PFC)与聚乙烯咔唑(PVK)掺杂体系的光致发光和电致发光特性.制备了结构分别为indium-tin-oxide(ITO)/PVK:PFC/bathocuproine(BCP)/tris-(8-hydroxylquinoline)-aluminum (Alq₃) /Mg:Ag，ITO/PFC/BCP/Alq₃/Mg∶Ag和ITO/PVK/BCP/Alq₃/Mg∶Ag的三种有机电致发光器件.对器件的光电特性进行了测试.结果表明，掺杂体系中的PVK有效地抑制了固态膜中PFC激基缔合物的形成.掺杂器件在不同的外加电场作用下发生发光层位置的移动，通过调节外加电场，可以获得从绿光到蓝光的可见光发射.当外加电压大于7V时，掺杂器件的蓝色发光亮度达到1650cd/m²，推测其中可能存在从PVK到PFC的能量传递过程.     

同时掺杂磷光和荧光染料的白色有机电致发光器件性能研究

以磷光染料Ir(piq)₂(acac)作为发光掺杂剂,掺入空穴传输性主体材料NPB中得到红色发光层,荧光材料TBP掺入到主体CBP中作为蓝色发光层,制备了结构为ITO/NPB/NPB：Ir(piq)₂(acac)/CBP/CBP：TBPe/BCP/ALq/Mg：Ag的双发光层白色有机电致发光器件.其中ALq₃、未掺杂的NPB和CBP及BCP层分别作为电子传输层、空穴传输层和激子阻挡层.实验中通过调节发光层厚度及Ir(piq)_{2关键词： 磷光 激子阻挡层 有机电致发光}     

An organic electrophosphorescent device driven by all-organic thin-film transistor using photoacryl as a gate insulator

Organic electrophosphorescent devices have been intensively investigated for using in full-color flat-panel display. Since the quantum efficiency of electrophosphorescent device decreases rapidly as the luminance increases, it is desirable to operate the electrophosphorescent display with active matrix rather than passive matrix. Here we report the study of driving electrophosphorescent diode with all-organic TFT. We obtained the maximum power luminance that was obtained about 90 cd/m². Turn-on voltage is approximately 10 V. Field effect mobility, threshold voltage, and on–off current ratio in 0.5-μm thick gate dielectric layer were 0.13 cm²/V s, −7 V, and 10⁶ A/A. The structure of electrophosphorescent diode is ITO/TPD/BCP:Ir(ppy)₃/BCP/Alq₃/Li:Al/Al. In organic TFT, photoacryl is used as an insulator and pentacene as an active layer.     

Solution-processed white organic light-emitting diodes with mixed-host structures

Efficient white light-emitting diodes (WOLEDs) were fabricated with a solution-processed single emission layer composed of a molecular and polymeric material mixed-host (MH). The main host used was a blue-emitting molecular material of 4,4′-bis(2,2′-diphenylvinyl)-1,1′-biphenyl (DPVBi) and the assisting host used was a hole-transport-type polymer of poly(9-vinylcarbazole) (PVK). By co-doping 4,4′-bis[2-(4-(N,N-diphenylamino)phenyl)vinyl]biphenyl and 5,6,11,12-tetraphenylnaphacene into the MH, the performances of the fabricated devices made with different mixing ratio of host materials were investigated, and were to depend on the mixing ratios. Under the optimal PVK:DPVBi ratio (3:7), we achieved a maximum luminance of 14 110 cd/m² and a maximum current efficiency of 9.5 cd/A. These improvements were attributed to the MH structure, which effectively improved the thermal stability of spin-coated film and enhanced the hole-injection/transporting properties of WOLEDs.     

Non-doped phosphorescent white organic light-emitting devices with a quadruple-quantum-well structure

Non-doped white organic light-emitting devices (WOLEDs) with a quadruple-quantum-well structure were fabricated. An alternate layer of ultrathin blue and yellow iridium complexes was employed as the potential well layer, while potential barrier layers (PBLs) were chosen to be 2,2',2''-(1,3,5-benzenetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) or N,N'-dicarbazolyl-3,5-benzene (mCP) combined TPBi. On adjusting the PBLs for device performance comparison, the results showed that the device with all-TPBi PBLs exhibited a yellow emission with the color coordinates of (0.50,0.47) at a luminance of 1000 cd/m², while stable white emission with the color coordinates of (0.36,0.44) was observed in the device using mCP combined TPBi as the PBLs. Meanwhile, for the WOLED, with a reduced efficiency roll-off, a maximum luminance, luminous efficiency, and external quantum efficiency of 12,610 cd/m², 10.2 cd/A, and 4.4%, respectively, were achieved. The performance improvement by the introduction of mCP PBL was ascribed to the well confined exciton and the reduced exciton quenching effect in the multiple emission regions.     

利用BCP层调节白色磷光有机电致发光器件色度的研究

制备了三种结构的白色有机电致发光器件，通过比较得出：在发光层中间插入2，9-二甲基-4，7-二苯基-1，10-菲咯啉(BCP)能有效控制载流子在不同发光层的分布，进而对器件色度进行调节；而掺杂磷光染料Ir(ppy)₃作敏化剂能有效提高器件的效率. 结构为:氧化铟锡/聚乙烯基咔唑∶N，N′-二(1-萘基)-N，N′-二苯基-1，1′-联苯-4-4′-二胺(30nm)/二-(2-甲基-8-羟基喹啉)-4-联苯酚铝：3.0 wt%2，5，8，11-tetra-tertbutylperylene(TBPe)(30nm)/BCP(5.0nm)/4,4N,N二咔唑基二苯：5.0 wt%Ir(ppy)₃:2.0 wt%红荧烯(15nm)/BCP(10nm)/Mg:Ag的器件色度和效率俱佳. 其在17V工作电压下具有的亮度为4670cd/m²，对应色坐标为(0.31,0.37). 器件具有的最大外量子效率为1.4%，当驱动电压从5.0V升高到17V，器件色坐标严格位于白光色域区内. 关键词： 磷光染料 阻挡层 白光 双发光层     

基于新型电荷生成层的P-i-N结构白色有机叠层电致发光器件

采用2,9-Dimethyl-4,7-diphenyl-1,10-phenanthroline(BCP): 5 wt.% cesium carbonate(Cs₂CO₃)和N, N'-Bis(naphthalen-1-yl)-N,N'-bis(phenyl)-benzidine(NPB): 20 wt.% molybdenum oxide(MoO₃)分别作为器件的电子注入层和空穴注入层,研究了N型和P-i-N结构有机电致发光器件的载流子传输特性.载流子传输层中BCP: Cs₂CO₃和NPB:MoO₃的引入有效增强了载流子注入能力,从而降低了器件的驱动电压.基于新型电荷生成层BCP: 5 wt.% Cs₂CO₃/ NPB: 20 wt.% MoO₃制备了色稳定、高效率P-i-N结构有机叠层器件.与单元器件相比,引入新电荷生成层有机叠层器件的最大电流效率增大了2.5倍,表明该电荷生成层可以有效地将电子和空穴分别注入到相邻发光单元中.采用该电荷生成层制备了P-i-N结构白色有机叠层器件,器件的上下发光单元分别为橙光和蓝光发射.当发光亮度从500增加到5 000 cd/m²时,器件的色坐标稳定在(0.33, 0.29)附近,接近白光等能点.利用单色发光单元堆叠制备白色有机叠层器件的方法为实现色稳定、高效率的白色有机电致发光器件提供了一种有效的途径.