Mode-Locked Erbium-Doped Fiber Laser Using Vanadium Oxide as Saturable Absorber

A mode-locked erbium doped fiber laser(EDFL) is demonstrated using the vanadium oxide(V_2O_5) material as a saturable absorber(SA). The V_2O_5 based SA is hosted into poly ethylene oxide film and attached on fiber ferule in the laser cavity. It shows 7% modulation depth with 71 MW/cm~2 saturation intensity. By incorporating the SA inside the EDFL cavity with managed intra-cavity dispersion, ultrashort soliton pulses are successfully generated with a full width at half maximum of 3.14 ps. The laser operated at central wavelength of 1559.25 nm and repetition frequency of 1 MHz.     

基于10 m光子晶体光纤的放大自相似锁模振荡器研究

基于单根10 m大模场面积保偏光子晶体光纤, 搭建了带有色散图的放大自相似振荡器; 通过仔细调节腔内色散量的大小以及位于色散补偿端的端镜前的狭缝位置和大小, 实现了稳定的锁模运转, 获得了抛物线形脉冲输出. 输出脉冲的重复频率为8.6 MHz, 脉冲宽度为6.2 ps, 光谱宽度为3.84 nm, 平均功率820 mW, 对应单脉冲能量95 nJ. 这是第一次在自相似振荡器中直接获得重复频率在10 MHz 以下的脉冲输出, 95 nJ也是目前自相似振荡器直接输出的最高脉冲能量. 通过数值模拟证实了在第一个光栅的零级反射处和狭缝滤波后可以分别实现抛物线型脉冲和高斯脉冲的两种锁模脉冲输出.     

Indium Tin Oxide Coated D-Shape Fiber as a Saturable Absorber for Generating a Dark Pulse Mode-Locked Laser

A dark pulse mode-locked laser is experimentally demonstrated using the indium tin oxide(ITO) coated Dshape fiber as a saturable absorber(SA).Using the polishing wheel technique,a D-shape single mode fiber was fabricated.A 60-nm-thick layer of ITO was deposited over the D-shape fiber using the electron beam deposition method.The SA has a saturation intensity of 40.32 MW/cm~2 and a modulation depth of 3.5%.A stable dark pulse mode-locked laser was observed at a central wavelength of 1559.4 nm with repetition rate 0.98 MHz,pulse width 370 ns and signal-to-noise ratio 61 dB.     

Reduced graphene oxide as saturable absorbers for erbium-doped passively mode-locked fiber laser

We demonstrate a nanosecond mode-locked erbium-doped fiber laser(EDFL)based on a reduced graphene oxide(RGO)saturable absorber(SA).The RGO SA is prepared by depositing the graphene oxide(GO)on fluorine mica through thermal reduction of GO.A scanning electron microscope(SEM),Raman spectrometer,and x-ray photoelectron spectroscopy(XPS)are adopted to analyze the RGO characteristics.The results show that the reduction degree of graphene oxide is very high.By embedding the RGO SA into the EDFL cavity,a stable mode-locked fiber laser is achieved with a central wavelength of 1567.29 nm and repetition rate of 12.66 MHz.The maximum output power and the minimum pulse duration are measured to be 18.22 mW and 1.38 ns respectively.As far as we know,the maximum output power of18.22 mW is higher than those of other nanosecond mode-locked oscillators reported.Such a nanosecond pulse duration and megahertz repetition rate make this mode-locked erbium-doped fiber laser a suitable seed oscillator for high-power applications and chirped pulse amplifications.     

Observation of stable bound soliton with dual-wavelength in a passively mode-locked Er-doped fiber laser

A phase-locked bound state soliton with dual-wavelength is observed experimentally in a passively mode-locked Erdoped fiber(EDF) laser with a fiber loop mirror(FLM). The pulse duration of the soliton is 15 ps and the peak-to-peak separation is 125 ps. The repetition rate of the pulse sequence is 3.47 MHz. The output power is 11.8 mW at the pump power of 128 mW, corresponding to the pulse energy of 1.52 nJ. The FLM with a polarization controller can produce a comb spectrum, which acts as a filter. By adjusting the polarization controller or varying the pump power, the central wavelength of the comb spectrum can be tuned. When it combines with the reflective spectrum of the fiber Bragg grating, the total spectrum of the cavity can be cleaved into two parts, then the bound state soliton with dual-wavelength at 1549.7 nm and 1550.4 nm is obtained.     

基于少数层石墨烯可饱和吸收的锁模光纤激光器

本文利用化学气相沉积法高温分解甲烷在铜箔上制得单层石墨烯薄膜, 测量了石墨烯的拉曼光谱. 将石墨烯薄膜逐层转移到光纤跳线的氧化锆插芯端面上做成可饱和吸收材料, 实验研究了环形腔掺铒光纤脉冲激光器的输出特性, 获得了峰值波长为1560.1 nm, 3 dB带宽为0.27 nm, 重复频率为7.69 MHz, 脉冲宽度为58.8 ps 的锁模脉冲序列. 时间带宽积为1.98, 表明脉冲出现了啁啾. 最后, 通过改变两个光纤活动接头之间的空气腔的长度, 激光波长实现了4 nm的调谐. 关键词： 光纤激光器 石墨烯 锁模     

Effect of doped fiber length on the stretch pulses of a mode-locked erbium-doped fiber laser

A passively self-starting mode-locked fiber ring laser is demonstrated using a highly concentrated Erbium doped fiber (EDF) with a saturable absorber. The effect of EDF length on the performance of the laser is investigated. Stable stretched pulses are obtained at wavelength region of 1560nm with a repetition rate ranging from 10.1 to 12.1 MHz and a pulse width stretching from 0.52 to 0.75 ps as the EDF length is reduced from 4.5 to 1.5 m. The repetition rate goes higher as the cavity length decreases when a shorter EDF is used but the pulse width reduces as the EDF length increases since the total group velocity dispersion (GVD) in the cavity is close to zero. The article is published in the original.     

Generation of domain-wall solitons in an anomalous dispersion fiber ring laser

We report experimental observations performed using a net anomalous dispersion Er-doped fiber ring laser without polarization-selective elements, highlighting the domain-wall solitary pulses generated under the incoherent polarization coupling. By adjusting the pump power and the polarization state appropriately, bright and dark solitons can stably co-exist in the cavity, both centered at 1562.16 nm with a 3-dB spectral width of ～ 0.15 nm and a repetition rate of 3.83 MHz. Moreover, the 0.8 mm long thulium-doped fiber (TDF) facilitated the mode-locking and self-starting of the laser. This is the first demonstration of a laser being used to generate bright and dark solitons synchronously while using TDF as the saturable absorber (SA). Except possessing the all-fiber structure, the laser exhibits good stability, which may have a significant influence on improvement of the pulse-laser design, and may broaden practical applications in optical sensing, optical communication, and soliton multiplexed systems.     

Stable mode-locked fiber laser using 49 cm long bismuth oxide based erbium doped fiber and slow saturable absorber

A stable mode-locked fiber laser employing a 49 cm long bismuth oxide based erbium doped fiber (Bi-EDF) by using a slow saturable absorber is demonstrated. Near transform limited short pulses with a repetition rate of 8.27 MHz are obtained at a wavelength of 1560 nm with a maximum spectral width of 15 nm. Results indicate that pulse characteristics are strongly dependent on pump power rather than spectral width. Moreover the Time-Bandwidth products (TBWP), pulse duration, the energy fluctuation and timing jitter decrease with increasing pump power. The pulse width is continuously varied from 1.2 ps to less than 300 fs. It produces stable mode locking with a maximum spectral width of 15 nm, minimum timing jitter of 4 ps and energy fluctuations of 2.5%. The pulse train was amplified using a two-stage amplifier up to 447 mW average power corresponding to peak powers of 177.3 kW.     

非线性放大环形镜“8”字腔光纤激光器实验研究

使用976 nm半导体激光器作为抽运源,对利用非线性放大环形镜（NALM）锁模运行的掺Yb3+光纤激光器进行了实验研究,获得了脉冲宽度43.6 ps,中心波长为1053.3 nm的锁模脉冲激光输出, 光谱宽度8 nm, 输出功率为0.2 mW, 重复频率为18.2 MHz, 经过放大, 通过光栅对腔外色散补偿,在腔外产生了宽度616 fs的脉冲激光.     

2 μm波段半导体可饱和吸收镜被动调Q光纤激光器

基于半导体可饱和吸收镜和光纤光栅实现了稳定的2 m波段被动调Q光纤脉冲激光器,输出激光的中心波长为1958.2 nm。随着泵浦功率的增加,输出脉冲的重复频率不断增加,而对应脉冲的宽度不断减小。输出脉冲重复频率的变化范围为20～80 kHz,脉冲宽度的变化范围为490 ns～1 s。当泵浦功率为1.3 W时,调Q光纤激光器的最大平均输出功率为91 mW,脉冲重复频率为80 kHz,脉冲宽度为490 ns,对应的最大单脉冲能量约为1.14 J。     

基于混合锁模的耗散孤子掺铒光纤激光器

从一种简单、全光纤结构的混合被动锁模掺铒光纤激光器中,得到了高稳定性、宽光谱的耗散孤子。激光器结合了半导体可饱和吸收体和非线性偏振旋转两种锁模机制,并运行在正常色散区内;通过色散管理,激光器能产生光谱宽度39.1 nm和时域宽度178 fs的孤子脉冲序列。激光输出的中心波长为1.55μm,重复频率约为34.3 MHz,单脉冲能量在0.33 nJ左右。与此同时,激光器的斜效率也约等于15.5%;室温工作下,激光器能实现自启动锁模,且运行在稳定单脉冲输出状态的时长在15 h以上。     

Nanosecond-pulsed erbium-doped fiber lasers with graphene saturable absorber

We demonstrate graphene mode-locked nanosecond erbium-doped fiber laser in an all-fiber ring cavity. The clean and robust pulse train was generated at 27 mW pump power. Resultant central wavelength, repetition rate and pulse width was 1560 nm, 388 kHz and 6 ns, respectively. With two stage fiber amplifier, the output power was 553 mW, corresponding to single pulse energy of 1.4 μJ. In addition, the pulse-width can be varied ranging from 3 ns to 20 ns at repetition rate between 200 kHz and 1.54 MHz by changing the length of the laser cavity.     

High repetition rate femtosecond laser nano-machining of thin films

Thin film laser micromachining has been utilized for repairing semiconductor masks, creating solar cells and fabricating MEMS devices. A unique high repetition rate femtosecond fiber laser system capable of variable repetition rates from 200 KHz to 25 MHz along with helium gas assist was used to study the effect of pulse repetition rate and pulse energy on femtosecond laser machining of gold-coated silicon wafer. It was seen that high repetition rates lead to smaller craters with uniform line width. Craters created at 13 MHz pulse repetition rate with 2.042 J/cm² beam energy fluence measured 110 nm in width and had a heat affected zone of 0.79 μm. It was found that pulse repetition rate only played a significant role in the size of the heat affected zone in the lower pulse energy ranges. In the future, a 1 W laser system will be acquired to find the optimal repetition rate that would create the minimal feature size with the least heat affected zone. Using this kind of setup along with techniques such as radial polarization and a different gas assist may enable us to create sub 100 nm feature size with good quality.     

Nanosecond Pulses Generation with Samarium Oxide Film Saturable Absorber

Nanosecond pulse generation is demonstrated in a mode-locked erbium-doped fiber laser(EDFL) utilizing a samarium oxide(Sm_2O_3) film. The Sm_2O_3 film exhibits a modulation depth of 33%, which is suitable for modelocking operation. The passively pulsed EDFL operates stably at 1569.8 nm within a pumping power from 109 to 146 m W. The train of generated output pulses has a pulse width of 356 nm repeated at a fundamental frequency of 0.97 MHz. The average output power of 3.91 m W is obtained at a pump power of 146 m W, corresponding to 4.0 nJ pulse energy. The experimental result indicates that the proposed Sm_2O_3 saturable absorber is viable for the construction of a flexible and reliably stable mode-locked pulsed fiber laser operating in the 1.5 m region.     

Sequential generation of self-starting diverse operations in all-fiber laser based on thulium-doped fiber saturable absorber

Self-starting Q-switching, Q-switched mode-locking and mode-locking operation modes are achieved sequentially in an all-fiber erbium-doped fiber laser with thulium-doped fiber saturable absorber for the first time. The central wavelengths of Q-switching, Q-switched mode-locking and mode-locking operation modes are 1569.7 nm, 1570.9 nm, and 1572 nm, respectively. The mode-locking operation of the proposed fiber laser generates stable dark soliton with a repetition rate of 0.99 MHz and signal-to-noise ratio of 65 dB. The results validate the capability of generating soliton pulse by doped fiber saturable absorber. Furthermore, the proposed fiber laser is beneficial to the applications of optical communication and signal processing system.     

超长腔碳纳米管锁模多波长掺镱光纤激光器

报道了一种超长腔碳纳米管锁模多波长掺镱光纤激光器, 光纤激光器的总长度为1021.2 m. 实验得到了噪声型孤子和孤子雨两种类型的多波长锁模脉冲, 重复频率均为199.8 kHz. 孤子雨具有更高的输出功率和单脉冲能量, 分别为40.3 mW和201.5 nJ, 对应的脉冲宽度为102.5 ns.     

微纳光纤镀铂金膜锁模光纤激光器

采用有限元法仿真了微纳光纤中模式在镀膜前后的能量、电场及有效折射率变化,分析了HE11、TE01、HE21和TM01模式在微纳光纤中的传输特性以及与铂金膜的相互作用原理。采用缓冲氧化物刻蚀液制作了微纳光纤并用离子喷溅法镀铂金膜,得到直径为13.2μm、铂金膜厚度为40 nm的微纳光纤器件,测试了其可饱和吸收特性,调制深度和饱和强度分别为0.57%和0.8 MW/cm²。制作了全光纤锁模激光器,锁模阈值为180 mW。锁模脉冲重复频率为17.93 MHz,脉冲宽度为103 ps,中心波长为1 031.6 nm,半高宽约为3.5 nm。     

皮秒光纤激光脉冲两个关键问题的研究

窄带耗散孤子锁模光纤激光器可以产生接近变换限制的皮秒脉冲，但受非线性相移的限制，输出脉冲重复频率不能通过增加腔长来降低，脉冲能量仅在0.1 nJ以下，严重制约着这类皮秒脉冲的实际应用。提出一种通过耦合器抽取腔内脉冲能量、抑制腔内非线性相移积累，进而允许增加腔长来降低窄带耗散孤子皮秒光纤激光脉冲重复频率的方法。运用该方法，成功地将激光器重复频率由35.2 MHz降低到了1.77 MHz，且脉冲时频特性保持不变。提出了一种基于级间FBG陷波滤波的抑制皮秒脉冲光纤放大中光谱展宽的方法。通过简单地使用级间陷波滤波器，既可窄化第一级光纤放大器后的输出脉冲谱宽，允许采用第二级光纤放大器进一步提升脉冲能量，而且，还可将脉冲重塑为近高斯形，利用高斯脉冲光谱展宽斜率小的特点，允许第二级光纤放大器将脉冲能量提升得更高。利用该方法，在RMS（均方值）谱宽保持0.4 nm以内的前提下，10 ps脉冲经标准单模光纤放大器后，能量可由0.2 nJ可提升到10 nJ以上。     

高功率2 μm波长可调谐超短脉冲光纤激光器

高功率2 μm波长可调谐的超短脉冲激光具有峰值功率高、脉冲宽度窄、波长可调谐等优势,在医疗手术、大气通信、光电对抗等领域具有广泛的应用。利用高峰值功率的掺铒光纤放大器泵浦高非线性光纤,在全光纤化结构中获得了1895～2165 nm可调谐的拉曼孤子输出。采用啁啾脉冲放大技术对拉曼孤子的脉冲能量进行提升,放大后拉曼孤子的单脉冲能量为1.56 μJ,平均功率达到50.6 W,脉冲宽度为83 ps。经过光栅对压缩后,脉冲宽度降低至1.23 ps,平均功率为22 W,峰值功率达到0.55 MW。放大后的脉冲仍具有波长调谐的能力,当输出功率为5 W和50.6 W时,脉冲的波长调谐范围分别为38 nm和8 nm。