Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

Simultaneous dual-wavelength Q-switched Nd:YAG laser operating at 1.06 μm and 946 nm

Considering the reabsorption loss of the quasi-three level system and the unsaturable loss of the saturable absorber, we obtained the operating condition of a diode-pumped simultaneous dual-wavelength Q-switched Nd:YAG laser operating at 1.06 μm and 946 nm. The dual-wavelength pulsed laser was realized successfully through adaptive coating design of the cavity mirrors. As much as 1.6 W total average output power of the dual-wavelength at 1.06 μm and 946 nm was achieved at the incident pump power of 14.2 W with an optical conversion efficiency of 11.3%.     

Dual-wavelength bandwidth-narrowed output of a high-power diode laser using a simple external cavity

Using an external cavity consisting of an etalon and a mirror, dual-wavelength operation of a high-power broad-area multi-stripe diode laser is achieved. The reflection of the etalon is used as the output beam of the system. The free-running bandwidth of the laser diode is about 2.0 nm. At dual-wavelength operation, the bandwidth of each wavelength component is narrowed to about 0.07 nm, while the space between them is 1.65 nm, determined by the FSR of the etalon. We obtain an available dual-wavelength output power of 2.0 W at the drive current of 6.5 A. The power ratio of the components at two different wavelengths can be changed by changing the temperature of the diode laser. To tune the wavelength of the dual-wavelength output, the temperature of the laser diode and the tilt angle of the etalon are changed simultaneously PACS 42.55.Px; 42.60.Fc; 42.60.Da     

Multi-wavelength operation of LD side-pumped Nd:YAG laser

A dual-wavelength laser at 1064 nm and 1319 nm is obtained by a single Nd:YAG crystal rod. On the basis of 1064 nm and 1319 nm dual-wavelength laser installation, the second harmonic waves at 532 nm and 660 nm can be achieved by using non-linear frequency conversion technology. When 1064 nm and 1319 nm lasers oscillate simultaneously, the maximum output power is 30.5 W and 8.78 W, respectively. When the 1319 nm laser is restrained, we obtain a 35.6 W maximum output power at 1064 nm and by contrary 11.2 W at 1319 nm. The maximum output powers of 532 nm and 660 nm lasers are 5.34 W and 1.353 W when oscillating simultaneously. With one of them restrained, the maximum output power is 6.72 W at 532 nm and 1.90 W at 660 nm. The optimum repetition rate of the acousto-optic Q-switch is 10.5 KHz and 20.5 KHz for 532 nm and 660 nm lasers, respectively. The optical-to-optical conversion efficiency from the fundamental waves to the harmonic waves is 17.5% and 15.4%. The instability is less than 2%.     

Diode-end-pumped linear-polarized single-frequency Tm:YAG laser at room temperature

By using two solid uncoated etalons, we present a diode-pumped linear-polarized single-frequency Tm:YAG laser operating at 2 μm. Placing one 0.1 mm F-P etalon at nearly Brewster angle in the cavity, the linear-polarization laser is achieved. The other 1 mm F-P etalon was turned in the range of very small angle, single-longitudinal-mode (SLM) could be obtained. The maximum output power of linear-polarized single-frequency laser of 60 mW is achieved at the wavelength of 2013 nm. The degree of the polarization is over 30 dB. Long-term frequency stability was also investigated, with the results of wavelength fluctuation about 2.55 × 10⁻¹³ m within 3 min and frequency change about 18.86 MHz, corresponding to a frequency stability of 1.27 × 10⁻⁷.     

High-power simultaneous dual-wavelength emission of an end-pumped Nd:YAG laser using the quasi-three-level and the four-level transition

An efficient continuous-wave (CW) simultaneous dual-wavelength lasing (SDWL) of an LD end-pumped Nd:YAG laser utilizing a quasi-three-level transition at 946 nm and a four-level transition at 1064 nm is reported. A theoretical model has been introduced to determine the threshold conditions for SDWL. The temperature distributions of a Nd:YAG crystal under different pump powers have been analyzed. In the experiments, a CW SDWL output power of 5.12 W at a temperature of 273 K has been achieved with a pump power of 17 W, giving a slope efficiency of 16.36%.     

43 W picosecond laser and second-harmonic generation experiment

Combining the advantages of diode-end-pumped Nd: YVO₄ and diode-side-pumped Nd: YAG amplifiers, a high average power and high beam quality picosecond laser is designed. The system delivers a picosecond laser with average power of 43.4 W and good beam quality of M² < 1.7. By focusing the high power picosecond laser in LBO crystal, 532 nm green laser with maximal power of 20.8 W is generated and the conversion efficiency of second-harmonic generation reaches 56.4% when 17.7 W green laser obtained from the fundamental frequency laser with power of 31.4 W and beam quality of M² < 1.25.     

Incorporate, switchable dual-wavelength fiber laser with Bragg gratings written in a polarization-maintaining erbium-doped fiber

A stable, incorporate and switchable dual-wavelength fiber laser with two fiber Bragg gratings written in a photosensitive and polarization-maintaining erbium-doped fiber directly, that is, without splices in the laser cavity, is proposed and demonstrated. Simultaneous dual-wavelength oscillation is achieved at room temperature with a wavelength spacing of 0.343 nm. The power fluctuation and wavelength shift of single-wavelength oscillations are measured to be less than 0.24 dB and 0.013 nm over 2 h. The wavelength switchability between single- and dual-wavelength oscillations is realized by altering the voltage upon the electrostrictive ceramic actuator.     

Enhancement of terahertz wave difference frequency generation based on a compact walk-off compensated KTP OPO

A compact, walk-off compensated dual-wavelength KTP OPO near the degenerate point of 2.128 μm pumped by a Nd:YAG pulsed laser is employed as the pump for terahertz (THz) source based on difference frequency generation (DFG) in a GaSe crystal. Coherent THz radiation that is continuously tunable in the range of 81-1617 μm (0.186-3.7 THz) is achieved. An enhancement of 76.7% in average for the THz energies at different wavelengths is realized using the walk-off compensated KTP OPO than the common one. Using a 8 mm-long GaSe crystal, the maximum output THz pulse energy is 48.9 nJ with the peak power of 11 W, corresponding to the energy conversion efficiency of 5.4 × 10^− 6 and the photon conversion efficiency of about 0.09%.     

Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser

We demonstrate the generation of TEM₀₀ mode yellow light in critically type II phase-matched KTiOPO₄ (KTP) with intracavity frequency doubling of a diode-pumped Nd:YAG laser at room temperature. After a 150 μm thick etalon have been inserted into the cavity, the stability and beam quality of the second harmonic generation (SHG) is enhanced. A continuous wave (CW) TEM₀₀ mode output power of 1.67 W at 556 nm is obtained at a pump level of 16 W. The total optical to optical conversion efficiency is about 10.44%. To the best of our knowledge, this is the first Watt-level yellow light generation by frequency doubling of Nd:YAG laser.     

A tunable narrow-line-width multi-wavelength Er-doped fiber laser based on a high birefringence fiber ring mirror and an auto-tracking filter

A novel multi-wavelength erbium-doped fiber laser operating in C-band is proposed and successfully demonstrated. The wavelength interval between the wavelengths is about 0.22 nm. The 3 dB bandwidth of the laser is about 0.012 nm, and the output power reaches 4.8 mW. By using a high birefringence fiber ring mirror (HiBi-FLM) and a tunable FBG, the laser realizes switchable and tunable characteristic. The mode hopping can be effectively prevented. Moreover, this laser can improve wavelength stability significantly by taking advantage of an un-pumped Er³⁺-doped fiber at the standing-wave section. The laser can operate in stable narrow-line-width with single-, dual-wavelength, and unstable triple-wavelength output at room temperature.     

High conversion efficiency solar laser pumping by a light-guide/2D-CPC cavity

A simple and efficient light-guide/2D-CPC solar pumping approach is proposed. A fused silica light-guide assembly is used to transmit 6 kW concentrated solar power from the focal spot of a large parabolic mirror to the entrance aperture of a 2D-CPC pump cavity, where a long and thin Nd:YAG rod is efficiently pumped. Numerical calculations are made for different light-guides, 2D-CPC cavities and laser rods. The laser output power is investigated through finite element analysis. With 4 mm diameter rod, the maximum calculated laser power of 75.8 W is obtained, corresponding to the conversion efficiency of more than 11 W/m². The tracking error dependent laser power losses are lower than 4%. A small scale prototype was constructed and tested, reaching 8.1 W/m² conversion efficiency.     

Continuous-wave operation of a room-temperature Ho:YAP laser pumped by a Tm:YAP laser

We reported the Ho:YAP laser pumped by the Tm:YAP laser. The Ho:YAP laser maximum output power was 4.91 W when the incident power was 10.1 W with the threshold of 2.63 W. The slope efficiency was 63.7%, corresponding to an optical-to-optical efficiency of 48.6%. The Ho:YAP output wavelength was centered at 2118.2 nm with bandwidth of about 1 nm. We estimate the beam quality to be M² = 1.29.     

Diode-pumped continuous-wave dual-wavelength Yb:CaNb2O6 lasers at 1003 nm and 1038 nm

A diode-pumped high-power continuous-wave (cw) dual-wavelength Yb:CaNb₂O₆ lasers at 1003 nm and 1038 nm is reported. By using an end-pumped structure and employing a 978 nm diode-laser as the pump source. As a result, the total output power of 803 mW dual-wavelength lasers at 1003 nm and 1038 nm is obtained at an incident pump power of 17.8 W. Furthermore, intracavity sum-frequency mixing at 1003 and 1038 nm was then realized in a LBO crystal to reach the green range. We obtained a total cw output power of 94 mW at 510 nm.     

High frequency microwave signal generation using dual-wavelength emission of cascaded DFB fiber lasers with wavelength spacing tunability

A dual-wavelength fiber laser source based on two cascaded phase-shifted fiber Bragg gratings is presented. The gratings are written in an erbium-doped fiber, each configuring the cavity of a distributed feedback fiber laser. The spacing between lasing modes is controlled dynamically by the use of piezoelectric actuators. A continuous tuning range of 5-724 pm of the wavelength difference, which is equivalent to a photodetected 0.72-92 GHz range, is obtained. Efficient generation from the L to the W microwave and millimeter bands has been achieved by heterodyne photodetection of the dual-wavelength optical signal.     

High efficiency Tm fiber laser of seed amplification

We use all-fiber single-mode lasers as seed source, amplifiers and pump laser coupling amplifier has been experimentally investigated, respectively. The maximum output power is 10.4 W, with the slope efficiency of 54.4% when the seed laser power is 1 W, and the slope efficiency is 48.7% when the seed laser power is 2 W. The slope efficiency of this scheme is higher than that of the all-fiber amplifier. This can be explained by the loss of pump power at the splice dots. The wavelength of the fiber amplifier is 1947.6 nm, the same as the seed laser's, with a linewidth of 2 nm. We estimate the beam quality to be M² = 2.39, clearly indicating nearly diffraction-limited beam propagation.     

Diode-pumped passively Q-switched 912 nm Nd:GdVO4 laser and pulsed deep-blue laser by intracavity frequency-doubling

A diode-end-pumped passively Q-switched 912 nm Nd:GdVO₄/Cr⁴⁺:YAG laser and its efficient intracavity frequency-doubling to 456 nm deep-blue laser were demonstrated in this paper. Using a simple V-type laser cavity, pulsed 912 nm laser characteristics were investigated with two kinds of Cr⁴⁺:YAG crystal as the saturable absorbers, which have the different initial transmissivity (T_U) of 95% and 90% at 912 nm. When the T_U = 95% Cr⁴⁺:YAG was used, as much as an average output power of 2.8 W 912 nm laser was achieved at an absorbed pump power of 34.0 W, and the pulse width and the repetition rate were ∼ 40.5 ns and ∼ 76.6 kHz, respectively. To the best of our knowledge, this is the highest average output power of diode-pumped passively Q-switched Nd³⁺-doped quasi-three-level laser. Employing a BiBO as the frequency-doubling crystal, 456 nm pulsed deep-blue laser was obtained with a maximum average output power of 1.2 W at a repetition rate ∼ 42.7 kHz.     

Self-Q-switched and mode-locked Nd,Cr:YAG laser with 6.52-W average output power

Simultaneous self-Q-switched and mode-locked have been demonstrated in a diode-pumped Nd,Cr:YAG laser. For the first time as we know, almost 100% modulation depth has been achieved at an intracavity intensity of 5.6 × 10⁵ W/cm². The maximum average output power of 6.52 W corresponding to a slope efficiency of 30% is obtained at 1064 nm. The laser produces high-quality pulses in a TEM₀₀-mode at the pump power of 16.5 W. The pulse duration of the mode-locked pulses is about 600 ps with 136 MHz repetition rate.     

Dual-Wavelength and Passively Q-Switched Nd :GdVO4 Lasers Operated at 1.34 μm Under 880 nm Diode Pumping

We report continuous-wave (CW) and passively Q-switched Nd :GdVO₄ lasers on ⁴F_3/2 → ⁴I_13/2 transition directly pumped by an 880 nm diode laser. A widely investigated Nd :GdVO₄ laser at about 1341 nm is operated with a maximum output power of 5.23 W and a slope efficiency of about 30.6%. Using an etalon for wavelength selection, we realize laser emission at about 1344 nm, for the first time to our knowledge, in a Nd :GdVO₄ laser, with a maximum output power of 4.19 W and a slope efficiency of 20.1%. Moreover, we achieve simultaneous dual-wavelength lasing at 1341 and 1344 nm with a maximum output power of 2.27 W and a slope efficiency of 13.5%, respectively. Using V³⁺ :YAG as a saturable absorber, stable Q switching is obtained at about 1341 nm with a maximum average output power of 1.15 W. The pulse width is 52.8 ns at a repetition rate of 279.8 kHz.

     

QCW diode-pumped 654 W AO Q-switched Nd:YAG rod oscillator-amplifier laser

A diode laser-pumped acoustic-optic Q-switched Nd:YAG master-oscillator power amplifier laser is presented. The laser is quasi continuously pumped at 1.1 kHz with a pulse width of 172 μs, and the ultrasonic frequency of the AO Q-switcher is set at a higher value (53 kHz). The master oscillator is designed as a thermally near-unstable-resonator, which presents an average output power of 48 W with a beam quality value of M² = 1.41 and a Q-switching pulse duration of 121 ns. The maximum average power of the MOPA system is 654 W, and the beam quality is M² = 6.