W/Fe/CuCrZr热等静压模块组织及性能分析

为实现面向等离子体材料钨(W)和热沉材料铜铬镐(CuCrZr)合金的可靠连接,对纯铁(Fe)作为W/CuCrZr合金热等静压连接中间层的可行性进行了探索性研究。在850℃/150MPa/135min的热等静压参数下制作了W/Fe/CuCrZr合金的实验模块,分别对连接界面进行了焊接界面、微观形貌、组织成分及剪切力学性能的检测分析。检测结果显示,两连接界面无明显缺陷,均发生了约0.5μm的短距离互扩散,且均未生成明显的反应相,连接界面呈现出较好的塑性,剪切强度大于186.5MPa。因此,纯铁作为中间层实现了W/CuCrZr合金的可靠连接。用ANSYS Workbench平台对模块进行的高热负荷下的瞬态传热模拟表明W/Fe/CuCrZr合金模块最高可承受16MW·m^-2的热负荷。     

Fe/Si多层膜的层间耦合与界面扩散

对以本征Si及重掺杂ｐ型和ｎ型Si作为中间层的Fe/Si多层膜的层间耦合进行研究，并通过退火，增大Fe，Si之间的扩散，分析界面扩散对层间耦合的影响. 实验结果表明，层状结构良好的制备态的多层膜，Fe，Si之间也存在一定程度的扩散，它是影响层间耦合的 主要因素，远远超过了半导体意义上的重掺杂，使不同种类的Si作为中间层的层间耦合基本 一致.进一步还发现，在一定范围内增大Fe，Si之间的扩散，即使多层膜的层状结构已经有了相当的退化，Fe/Si多层膜的反铁磁耦合强度基本保持不变. 关键词： Fe/Si多层膜 层间耦合 界面扩散     

钨/低活化钢钎焊用铁基非晶钎料与接头微结构

为了连接W和CLF-1 RAFM钢,设计出由低活化元素组成的Fe-B-Si、Fe-B-Si-Sn、Fe-B-Si-Cr-(Sn)、Fe-B-Si-P-(Cr,Sn)、Fe-B-Si-Mn-(Ga,Sn)和Fe-B-Si-(Cr,Mn,Ga,Ta,Sn)系列Fe基非晶钎料,结合熔体快淬技术制备出非晶合金箔带,并对W/CLF-1 RAFM钢接头微结构进行了对比研究。采用X-射线衍射仪对箔带样品与焊缝进行了相鉴定;通过差热分析测量了非晶箔带的熔化温度和液相线温度;利用光学金相和电子探针分析了焊缝组织形貌和元素分布。结果表明,利用Fe-B-Si、Fe-B-Si-Cr和Fe-B-Si-Mn-Sn非晶钎料可获得结构完整的W/CLF-1钢接头;前两种钎料得到的焊缝组织基体相为α-Fe固溶体,而含Mn钎料形成的焊缝基体为马氏体组织;在高温钎焊过程中,这些Fe基非晶钎料中的高B含量促使FeWB、FeW2B2和Fe3B型金属间化合物在焊缝中形成,并有效地阻止了W元素向低活化钢基体长程扩散。所设计的低活化Fe基非晶钎料可用于W和低活化钢的连接和接头性能研究。     

W/RAFM 钢偏滤器靶板的结构分析与寿命预测

探究RAFM 钢作为偏滤器靶板热沉的替换材料，验证其在3 种不同工况下的结构强度并预测其在交变载荷下的疲劳寿命。得出3S_m 法则下W/RAFM 钢偏滤器靶板最大可承受热负荷为8MW·m⁻²。结合中国聚变工程实验堆(CFETR)的设计目标，如果以ITER 偏滤器两年运行周期为设计准则，最大承受热负荷为7MW·m⁻²。考虑到偏滤器靶板区域呈现高热负荷低中子辐照、挡板和DOME板区域低热负荷高中子辐照特性，可以采用W/Cu 和W/RAFM 双路偏滤器靶板的结构设计。     

低活化马氏体钢热等静压焊接接头性能初步研究

研究了低活化马氏体钢(CLF-1)热等静压(HIP)焊接接头的性能,经980℃/1h/空冷+740℃/2h/空冷的性能热处理后,接头组织保持着CLF-1钢母材回火马氏体组织;常温拉伸性能与母材相当,断口为韧窝状且有第二相粒子产生,为塑性断裂且断于焊缝;常温冲击功最高为母材的26.2%。初步分析认为焊接表面制备状态、表面污染物、表面清洗状态、表面氧化膜都会影响基体原子充分扩散,导致界面扩散层不均匀,焊缝裂纹敏感性增强,冲击功低,且不稳定。     

低活化马氏体钢热等静压焊接接头性能初步研究

研究了低活化马氏体钢(CLF-1)热等静压(HIP)焊接接头的性能,经980℃/1h/空冷+740℃/2h/空冷的性能热处理后,接头组织保持着CLF-1钢母材回火马氏体组织;常温拉伸性能与母材相当,断口为韧窝状且有第二相粒子产生,为塑性断裂且断于焊缝;常温冲击功最高为母材的26.2%。初步分析认为焊接表面制备状态、表面污染物、表面清洗状态、表面氧化膜都会影响基体原子充分扩散,导致界面扩散层不均匀,焊缝裂纹敏感性增强,冲击功低,且不稳定。     

Fe-B-Si非晶钎焊W/CLF-1接头组织和性能研究

通过电弧熔炼制备了Fe75B16.67Si8.33非晶合金,通过真空钎焊获得了钨/低活化钢接头.通过对钎焊接头表面形貌、微观组织、成分和力学性能的表征,发现在1250℃保温10min下所获得的钎焊接头界面无孔洞、裂纹等宏观缺陷,接头组织中生成了Fe固溶体、Fe3B和FeWB金属间化合物,拉伸强度高达450MPa.     

(Fe1-xNix)2P电子结构与磁学特性的X射线近边吸收谱研究

利用X射线近边吸收谱对Fe₂P,Ni₂P及其掺杂物(Fe_1-xNi_x)₂P(x=01,025,05)中Fe,Ni,P的K边进行了研究.结合多重散射理论近边计算,讨论了金属原子不同位置格点3f,3g对近边谱特征的贡献,得出当Ni原子取代Fe原子时将优先占据Fe(3f)格点位置;根据第一性原理对能态的计算发现,不考虑磁性时不同格点P的pDOS未占据态电子结构与P-K近边吸收谱实验相符合;与考虑铁磁性Fe₂P 的DOS相比较后结果显示Fe₂P的磁性主要来源于Fe(3g)格点,铁磁性Ni₂P计算的Ni不同格点原子磁矩均接近于0,与它一般显顺磁性结论相一致. 关键词： X射线近边吸收谱 电子结构 多重散射理论 态密度     

掺杂半导体β-FeSi2电子结构及几何结构第一性原理研究

采用基于第一性原理的密度泛函理论全势线性缀加平面波法，使用广义梯度近似处理交换相关势能，首先计算了β-FeSi₂的电子结构及其各元素各亚层电子的能态密度，β-FeSi₂的电子能态密度主要由Fe的d层电子和Si的p层电子的能态密度确定；其次通过计算不同掺杂系统的总能量确定了掺杂原子在β-FeSi₂中的置换位置，在β-FeSi₂中，Co置换Fe_Ⅱ位置的Fe原子，Al置换Si_Ⅰ位置的Si原子，这种择位置换与现有的计算结果完全一致；最后计算了Fe_1-xCo_xSi₂和Fe(Si_1-xAl_x)₂的电子结构，对它们的电子结构特征进行了分析，并探讨了电子结构对其热电性能(塞贝克系数、电传输及热传输性能)的影响. 关键词： 第一性原理 电子结构 热电性能 2')" href="#">FeSi₂     

界面对Fe65Co35薄膜微结构和软磁性的影响

用不同的材料（Co₉₃Fe₇和Fe）作衬底层,利用磁控溅射法成功制备了Fe₆₅Co₃₅（主层）/衬底层结构的双层薄膜．通过X射线衍射和磁性测量发现,在不同的衬底上沉积的Fe₆₅Co₃₅薄膜的织构不同,并且（200）取向的Fe₆₅Co₃₅薄膜的面内各向异性和软磁性优于（110）取向的Fe₆₅Co_{35关键词： 65}Co₃₅薄膜')" href="#">Fe₆₅Co₃₅薄膜 衬底层 界面各向异性 软磁性     

Magnetoresistance of Fe3O4/Au/Fe3O4 and Fe3O4/Au/Fe spin-valve structures

A detailed study of the in-plane magnetotransport properties of spin valves with one and two Fe₃O₄ electrodes is presented. Fe₃O₄/Au/Fe₃O₄ spin valves exhibit a clear anisotropic magnetoresistance in small magnetic fields but no giant magnetoresistance (GMR). The absence of GMR in these structures is due to simultaneous magnetization reversal in the two Fe₃O₄ layers. By contrast, a negative GMR effect is measured on Fe₃O₄/Au/Fe spin valves. The negative GMR is attributed to an electron spin scattering asymmetry at the Fe₃O₄/Au interface or an induced spin scattering asymmetry in the Au interfacial layers.     

Desorption of H2 from W(110) and Fe covered W(110) surfaces

The kinetics of H₂ desorption from H/W(110) and H/Fe₁/W(110) were studied by measuring work function changes Δø vs time at a number of temperatures. Combination with previously determined Δø vs coverage data and differentiation at various fixed coverages gave rate vs T data from which activation energies of desorption could be obtained. E vs coverage results agree well with previously determine ΔH_des results. In the case of H/Fe₁/W(110) this includes a rise from 20 to 30 kcal mol⁻¹ of H₂ at H/Fe = H/W > 0.3. Plots of rate −dθ/dt vs θ (θ being coverage in units of H/W) vary much more steeply than θ² at most coverages for both systems. The θ dependence can be explained almost quantitatively in terms of the variations of ΔH_des and surface entropy S_s with coverage, by assuming that rates of desorption are equal to the equilibrium rates of adsorption. The latter can be formulated thermodynamically, except for a sticking coefficient, s. Values for s(θ, T) can also be obtained and show relatively little temperature dependence.     

用于核聚变装置的W/Cu 穿管部件的制备与辐照性能研究

采用了两步热等静压法制备W/Cu 穿管部件,即先用热等静压(930℃,100MPa,2h)在钨块的孔内壁上覆一层无氧铜作为中间层,然后再用热等静压工艺(600℃,100MPa,2h)把W/Cu 复合块与CuCrZr 管串接起来。经过高热负荷辐照测试,部件经受住了1000 次10MW•m⁻² 高热负荷的辐照,满足使用要求。     

Structural and magnetic study of swift heavy ion irradiated W/Fe multilayer structure

The present study reports the effect of swift heavy ion irradiation on structural and magnetic properties of sputtered W/Fe multilayer structure (MLS) having bilayer compositions of [W(10 Å)/Fe(20 Å)]_10BL. The MLS is irradiated by 120 MeV Au⁹⁺ ions of fluences 1×10¹³ and 4×10¹³ ions/cm². Techniques like X-ray reflectivity (XRR), cross-sectional transmission electron microscopy (X-TEM) and DC magnetization with a vibrating sample magnetometer (VSM) are used for structural and magnetic characterization of pristine and irradiated MLS. Analysis of XRR data using Parratt’s formalism shows a significant increase in W/Fe layer roughness. X-TEM studies reveal that intra-layer microstructure of Fe layers in MLS becomes nano-crystalline on irradiation. DC magnetization study shows that with spacer layer thickness interlayer coupling changes between ferromagnetic to antiferromagnetic.     

Re_3W的点接触安德烈夫反射谱研究

本文通过对不同晶体结构Re_3W样品的点接触测量和对比研究,证实具有中心对称结构和非中心对称结构的Re_3W都是弱耦合Bardeen-Cooper-Schrieffer超导体,同时发现在两个相表面都可以形成很理想的点接触结,即电子通过界面时受到的非弹性散射很弱.将Re_3W样品置于大气环境近六个月后重新进行测量,仍然能够得到类似的结果,表明Re_3W具有很好的稳定性. Re_3W的这种优良特性,不仅可通过点接触实验得到的参数推算出Re_3W两个相的费米速度,而且提供了一种简单的方法,可以在点接触实验中利用Re_3W来印证针尖材料的费米速度和测量其自旋极化率等.作为尝试,本文用Re_3W/Ni点接触结测量了铁磁性金属Ni的自旋极化率,得到了与前人报道一致的结果.     

Interfacial resonance state probed by spin-polarized tunneling in epitaxial Fe/MgO/Fe tunnel junctions

The direct impact of the electronic structure on spin-polarized transport has been experimentally proven in high-quality Fe/MgO/Fe epitaxial magnetic tunnel junctions, with an extremely flat bottom Fe/MgO interface. The voltage variation of the conductance points out the signature of an interfacial resonance state located in the minority band of Fe(001). When coupled to a metallic bulk state, this spin-polarized interfacial state enhances the band matching at the interface and therefore increases strongly the conductivity in the antiparallel magnetization configuration. Consequently, the tunnel magnetoresistance is found to be positive below 0.2 V and negative above. On the other hand, when the interfacial state is either destroyed by roughness-related disorder or not coupled to the bulk, the magnetoresistance is almost independent on the bias voltage.     

Effect of swift heavy ion irradiation in Fe/W multilayer structures

Present study reports effect of swift heavy ion irradiation on structural and magnetic properties of sputtered Fe/W multilayer structures (MLS) having bilayer compositions of [Fe(20 Å)/W(10 Å)]_5BL and [Fe(20 Å)/W(30 Å)]_5BL. These MLS are irradiated by 120 MeV Au⁹⁺ ions up to fluence of 4 × 10¹³ ions/cm². X-ray reflectivity (XRR), wide-angle X-ray diffraction (WAXD), cross-sectional transmission electron microscopy (X-TEM) and magneto optical Kerr effect (MOKE) techniques are used for structural and magnetic characterization of pristine and irradiated MLS. Analysis of XRR data using Parratt's formalism shows a significant increase in W/Fe interface roughness. WAXD and X-TEM studies reveals that intra-layer microstructure of Fe-layers in MLS becomes nano-crystalline on irradiation. MOKE study shows increase in coercivity at higher fluence, which may be due to increase in surface and interface roughness after recrystallization of Fe-layers.     

Insights into the sonochemical decomposition of Fe(CO)5: theoretical and experimental understanding of the role of molar concentration and power density on the reaction yield

The present work analyses, in detail, the optimization of a sonochemical process with respect to concentration of precursor and power supplied in a system. This is due to that even a small change in power dramatically changes the high-energy conditions created with the bubble collapse. A model reaction that has been considered for this purpose involves the decomposition of Fe(CO)₅ in decalin solvent as this reaction is strongly influenced by the cavitation conditions. Sonochemical treatment of this carbonyl results in the formation of amorphous Fe₂O₃, which on heat treatment gives nanocrystalline Fe₂O₃. It has been observed that concentration and power density parameters play an important role to obtain higher decomposition of Fe(CO)₅ and hence higher yield of the amorphous Fe₂O₃ product. Also, using the experimentally observed results, a correlation (polynomial) has been developed.