Nanocrystalline ZnO Film Grown on Porous SnO2/Si(111) Substrate

Porous tin oxide was prepared on silicon(111) substrate by the sol–gel route. Then, the samples were dried in air at 600°C for 30 min in an electric furnace. Scanning electron microscope (SEM) images indicated the high density of the pores. Circular microvoids formed by the rigid shaped microarray network of 200–300 nm sizes are clearly seen in the plan view SEM image. The high homogeneity and uniformity of the porous region could also be visualized by this easy method. Nanocrystalline zinc oxide (ZnO) thin films have been deposited onto porous SnO₂substrates at high growth rates by radio frequency (RF) sputtering using a ZnO target. The surface morphology of the nanocrystalline ZnO films was characterized by scanning electron microscope (SEM). Photoluminescence (PL) spectroscopy is a powerful, contactless and excellent nondestructive optical tool to study the acceptor binding energy of ZnO nanostructures. The PL measurements were also operated at room temperature. The peak luminescence energy in nanocrystalline ZnO on porous SnO₂ is blue-shifted with regard to that in bulk ZnO (381 nm). PL spectra peaks are distinctly apparent at 375 nm for ZnO film grown on porous SnO₂/Si(111) substrates.     

Structure and photoluminescence properties of epitaxial SnO2 films grown on α-Al2O3 (0 1 2) by MOCVD

SnO₂ thin films have been successfully deposited on α-Al₂O₃ (0 1 2) substrates by metalorganic chemical vapor deposition (MOCVD) in the temperature range 500-700 °C. The films were epitaxially grown in the tetragonal SnO₂ phase and were (1 0 1) oriented. In-plane orientation relationship [0 1 0]SnO₂||[1 0 0]Al₂O₃ and [1 0 1?]SnO₂||[1? 2? 1]Al₂O₃ was determined between the film and substrate. Photoluminescence (PL) spectra measured at room temperature revealed that the film grown at 700 °C showed an intense ultra-violet (UV) PL peak at 333 nm, which was a band-edge emission peak in SnO₂ films. At a temperature of 13 K, a new broad PL band centered at about 480 nm was observed. The corresponding PL mechanisms are discussed in detail.     

Optical Analysis of Nanocrystalline ZnO Films Coated on Porous Silicon by Radio Frequency (RF) Magnetron Sputtering

Zinc oxide thin films have been deposited onto porous silicon (PSi) substrates at high growth rates by radio frequency (RF) sputtering using a ZnO target. The advantages of the porous Si template are economical and it provides a rigid structural material. Porous silicon is applied as an intermediate layer between silicon and ZnO films and it contributed a large area composed of an array of voids. The nanoporous silicon samples were adapted by photo electrochemical (PEC) etching technique on n-type silicon wafer with (111) and (100) orientation. Micro-Raman and photoluminescence (PL) spectroscopy are powerful and non-destructive optical tools to study vibrational and optical properties of ZnO nanostructures. Both the Raman and PL measurements were also operated at room temperature. Micro-Raman results showed that the A₁(LO) of hexagonal ZnO/Si(111) and ZnO/Si(100) have been observed at around 522 and 530 cm^–1, re- spectively. PL spectra peaks are distinctly apparent at 366 and 368 cm^–1 for ZnO film grown on porous Si(111) and Si(100) substrates, respectively. The peak luminescence energy in nanocrystalline ZnO on porous silicon is blue-shifted with regard to that in bulk ZnO (381 nm). The Raman and PL spectra pointed to oxygen vacancies or Zn interstitials which are responsible for the green emission in the nanocrystalline ZnO.     

Effects of annealing temperature on the structural and photoluminescence properties of nanocrystalline ZrO2 thin films prepared by sol-gel route

Highly transparent nanocrystalline zirconia thin films were prepared by the sol-gel dip coating technique. XRD pattern of ZrO₂ thin film annealed at 400 °C shows the formation of tetragonal phase with a particle size of 13.6 nm. FT-IR spectra reveal the formation of Zr-O-Zr and the reduction of OH and other functional groups as the temperature increases. The transmittance spectra give an average transmittance greater than 80% in the film of thickness 262 nm. Photoluminescence (PL) spectra give intense band at 391 nm and a broad band centered at 300 nm. The increase of PL intensity with elevation of annealing temperature is related to reduction of OH groups, increase in the crystallinity and reduction in the non-radiative related defects. The luminescence dependence on defects in the film makes it suitable for luminescent oxygen-sensor development. The “Red shift” of excitation peak is related to an increase in the oxygen content of films with annealing temperature. The “Blue shift” of PL spectra originates from the change of stress of the film due to lattice distortion. The defect states in the nanocrystalline zirconia thin films play an important role in the energy transfer process.     

Structure, microstructure and photoluminescence properties of Fe doped SnO2 thin films

In this paper, effects of Fe doping on crystallinity, microstructure and photoluminescence (PL) properties of sol-gel derived SnO₂ thin films are reported. It is shown that doping of Fe³⁺ ions leads to crystallite size reduction and higher strain in SnO₂ thin films. The room temperature PL spectra show marked changes in intensity and blue-shift of the emission lines upon Fe doping. These observations have been correlated with structural changes and defect chemistry of Fe doped SnO₂ thin films.     

The comparison between CdS thin films grown on Si(111) substrate and quartz substrate by femtosecond pulsed laser deposition

Two kinds of cadmium sulfate (CdS) thin films have been grown at 600 °C onto Si(111) and quartz substrates using femtosecond pulsed laser deposition (PLD). The influence of substrates on the structural and optical properties of the CdS thin films grown by femtosecond pulsed laser deposition have been studied. The CdS thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), photoluminescence (PL) and Raman spectroscopy. Although CdS thin films deposited both on Si(111) and quartz substrates were polycrystalline and hexagonal as shown by the XRD , SEM and AFM results, the crystalline quality and optical properties were found to be different. The size of the grains for the CdS thin film grown on Si(111) substrate were observed to be larger than that of the CdS thin film grown on quartz substrate, and there is more microcrystalline perpendicularity of c-axis for the film deposited on the quartz substrate than that for the films deposited on the Si substrate. In addition, in the PL spectra, the excitonic peak is more intense and resolved for CdS film deposited on quartz than that for the CdS film deposited on Si(111) substrate. The LO and TO Raman peaks in the CdS films grown on Si(111) substrate and quartz substrate are different, which is due to higher stress and bigger grain size in the CdS film grown on Si(111) substrate, than that of the CdS film grown on the amorphous quartz substrate. All this suggests that the substrates have a significant effect on the structural and optical properties of thin CdS films. PACS 81.15.Fg; 81.05.Ea; 78.20.-e; 78.67.-n; 42.62.-b     

Substrate effects on the oxygen gas sensing properties of SnO2/TiO2 thin films

In this study, SnO₂/TiO₂ thin films are fabricated on SiO₂/Si and Corning glass 1737 substrates using a R.F. magnetron sputtering process. The gas sensing properties of these films under an oxygen atmosphere with and without UV irradiation are carefully examined. The surface structure, morphology, optical transmission characteristics, and chemical compositions of the films are analyzed by atomic force microscopy, scanning electron microscopy and PL spectrometry. It is found that the oxygen sensitivity of the films deposited on Corning glass 1737 substrates is significantly lower than that of the films grown on SiO₂/Si substrates. Therefore, the results suggest that SiO₂/Si is an appropriate substrate material for oxygen gas sensors fabricated using thin SnO₂/TiO₂ films.     

The role of the dopant in the magnetism of Fe-doped SnO2 films

Transparent pure and Fe-doped SnO₂ thin films were grown by pulsed laser deposition technique on LaAlO₃ substrates. X-ray diffraction shows that the films are polycrystalline and have the rutile structure. Surprisingly, the pure film presents magnetic-like behavior at room temperature with a saturated magnetization of almost one-third of the doped film (∼3.6 and 11.3 emu/g, respectively) and its magnetization could not be attributed to any impurity phase. Taking into account the magnetic moment measured in the pure film, the effective contribution of the impurity in the doped one can be inferred to be ∼2 μ_B per Fe atom. A large magnetic moment was also predicted by an ab initio calculation in the doped system, which increases if an oxygen vacancy is present near the Fe impurity.     

Growth mechanism and photoluminescence of the SnO2 nanotwists on thin film and the SnO2 short nanowires on nanorods

SnO2 nanotwists on thin film and SnO2 short nanowires on nanorods have been grown on single silicon substrates by using Au-Ag alloying catalyst assisted carbothermal evaporation of SnO2 and active carbon powders.The morphology and the structure of the prepared nanostructures are determined on the basis of field-emission scanning electron microscopy(FESEM),transmission electron microscopy(TEM),selected area electronic diffraction(SAED),high-resolution transmission electron microscopy(HRTEM),x-ray diffraction(XRD),Raman and photoluminescence(PL) spectra analysis.The new peaks at 356,450,and 489 nm in the measured PL spectra of two kinds of SnO2 nanostructures are observed,implying that more luminescence centres exist in these SnO2 nanostructures due to nanocrystals and defects.The growth mechanism of these nanostructures belongs to the vapour-liquid-solid(VLS) mechanism.     

Effects of deposition temperature on the structural and morphological properties of SnO2 films fabricated by pulsed laser deposition

Tin oxide (SnO₂) thin films were grown on Si (1 0 0) substrates using pulsed laser deposition (PLD) in O₂ gas ambient (10 Pa) and at different substrate temperatures (RT, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). XRD measurements showed that the almost amorphous microstructure transformed into a polycrystalline SnO₂ phase. The film deposited at 400 °C has the best crystalline properties, i.e. optimum growth conditions. However, the film grown at 300 °C has minimum average root mean square (RMS) roughness of 3.1 nm with average grain size of 6.958 nm. The thickness of the thin films determined by the ellipsometer data is also presented and discussed.     

Low energy electron diffraction studies of the surfaces of molecular crystals (ice,ammonia, naphthalene,benzene)

Low Energy Electron Diffraction (LEED) has been used to study the surface structures of thin films of molecular crystals. The samples were grown epitaxially on metal single crystal substrates at low temperatures. Both Pt(111) and Ag(111) surfaces were used as substrates in order to identify the influence of the substrate on molecular film structure. Previous observations of ice (0001) and naphthalene (001) surfaces on films grown on Pt(111) substrates [Surface Sci. 55 (1976) 413], were confirmed using the Ag(111) substrate. The NH₃(111) and benzene (111) surfaces were also studied on films grown on either substrate. All observed molecular crystal surfaces showed no evidence of surface reconstruction. To minimize sample charging and electron beam induced damage, LEED experiments were performed on samples of thickness less than 10?10² nm, with low energy electron exposures less than 1 C cm^?2. The maximum thickness and exposure values were characteristic of the particular molecular crystal. The relationship between the structure of the initial adsorbed monolayer and the molecular crystal orientation is discussed.     

Optical, electrical and morphological properties of p-type Mn-doped SnO2 nanostructured thin films prepared by sol–gel process

SnO₂ thin films doped with various manganese concentrations were prepared on glass substrates by sol–gel dip coating method. The decomposition procedure of compounds produced by alcoholysis reactions of tin and manganese chlorides was studied by thermogravimetric analysis (TGA). The effects of Mn doping on structural, morphological, electrical and optical properties of prepared films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Hall effect measurement, Fourier Transform Infrared (FTIR) spectral analysis, UV–Vis spectrophotometry, and photoluminescence (PL) spectroscopy. The results of the X-ray diffraction show that the samples are crystalline with a tetragonal rutile structure and the grain size decreases with increasing the doping concentration. The SEM and AFM images demonstrate that the surface morphology of the films was affected from the manganese incorporation. The Sn_1?x Mn _x O₂ thin films exhibited electrically p-type behavior in doping level above x=0.035 and electrical resistivity increases with increase in Mn doping. The optical transmission spectra show a shift in the position of absorption edge towards higher wavelength (lower energy). The optical constants (refractive index and extinction coefficient) and the film thickness were determined by spectral transmittance and using a numerical approximation method. The oscillator and dispersion energies were calculated using the Wemple–DiDomenico dispersion model. The estimated optical band gap is found to decrease with higher manganese doping. The room-temperature PL measurements illustrate the decrease in intensity of the emission lines when content of Mn is increased in Mn-doped SnO₂ thin films.     

Film thickness dependence of electro-optic effect in epitaxial BaTiO3 thin films

Based on the phenomenological Landau-Devonshire theory, we investigate the film thickness dependence of ferroelectric and electro-optic properties of epitaxial BaTiO₃ thin films grown on SrTiO₃ and MgO substrates. By using the effective substrate lattice parameter concept, the film thickness dependence of misfit strain is incorporated into the theory. Therefore, the film thickness dependence of ferroelectric and electro-optic properties in epitaxial BaTiO₃ thin films can be explained. Moreover, a large quadratic electro-optic effect was obtained in the BaTiO₃ thin films, which is in good agreement with the experimental result of BaTiO₃ thin films on the MgO substrate.     

Surface chemical states of barium zirconate titanate thin films prepared by chemical solution deposition

Ba(Zr_0.05Ti_0.95)O₃ (BZT) thin films grown on Pt/Ti/SiO₂/Si(1 0 0) substrates were prepared by chemical solution deposition. The structural and surface morphology of BZT thin films has been studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). The results showed that the random oriented BZT thin film grown on Pt/Ti/SiO₂/Si(1 0 0) substrate with a perovskite phase. The SEM surface image showed that the BZT thin film was crack-free. And the average grain size and thickness of the BZT film are 35 and 400 nm, respectively. Furthermore, the chemical states and chemical composition of the films were determined by X-ray photoelectron spectroscopy (XPS) near the surface. The XPS results show that Ba, Ti, and Zr exist mainly in the forms of BZT perovskite structure.     

Effects of interface between SnO2 thin film and Si substrate on growth time

SnO₂ thin film was grown on Si substrate using the low pressure chemical vapor deposition (LPCVD) method. The SnO₂ thin film was grown in the direction of (110) as deposition time increased. The atomic ratio of O decreased by 62.4, 57.6, and 45.6%, and the thickness of the thin film increased to 0.2, 0.3, and 0.7 ? as the deposition time increased to 10, 20, and 30 min, respectively. The interface of the thin film was examined using high-resolution transmission electron microscope (HRTEM) and energy dispersive spectroscopy (EDS) analysis. The SiO₂ layer was observed at between the SnO₂ thin film and the Si substrate. This layer decreased in thickness as the deposition time increased, which indicates that the deposition time affected the interface of the thin film.     

Structure-related infrared optical properties of BaTiO3 thin films grown on Pt/Ti/SiO2/Si substrates

BaTiO₃ thin films with different thickness have been grown on Pt/Ti/SiO₂/Si substrates by a modified sol-gel method. X-ray diffraction analyses show that the BaTiO₃ thin films are polycrystalline. The crystalline quality of the films is improved with increasing thickness. The infrared optical properties of the BaTiO₃ thin films have been investigated using an infrared spectroscopic ellipsometry in the wave number range of 800-4000 cm⁻¹ (2.5-12.5 μm). By fitting the measured pseudodielectric functions with a three-phase model (Air/BaTiO₃/Pt), and a derived classical dispersion relation for the thin films, the optical constants and thicknesses of the thin films have been simultaneously obtained. The refractive index of the BaTiO₃ thin films increases and on the other hand, the extinction coefficient does not change with increasing thickness in the entirely measured wave number range. The dependence of the refractive index on the film thickness has been discussed in detail and was mainly due to both the crystalline quality of the films and packing density. Finally, the absorption coefficient was calculated in the infrared region for applications in the pyroelectric IR detectors.     

Effect of process parameters on surface morphology and characterization of PE-ALD SnO2 thin films for gas sensing

Tin dioxide (SnO₂) thin films were deposited by plasma enhanced-atomic layer deposition (PE-ALD) on Si(1 0 0) substrate using dibutyl tin diacetate (DBTA) ((CH₃CO₂)₂Sn[(CH₂)₃-CH₃]₂) as precursor. The process parameters were optimized as a function of substrate temperature, source temperature and purging time. It is observed that the surface phenomenon of the thin films was changed with film thickness. Atomic force microscopy (AFM) images and X-ray diffraction (XRD) pattern were used to observe the texture and crystallanity of the films. The films deposited for 100, 200 and 400 cycles were characterized by XPS to determine the chemical bonding properties. XPS results reveal that the surface dominant oxygen species for 100, 200 and 400 cycles deposited films are O₂⁻, O⁻ and O²⁻, respectively. The 200 cycles film has exhibited highest concentration of oxygen (O⁻) species before and after annealing. Conductivity studies revel that this film has best adsorption strength to the oxygen ions forming on the surface. The sensor with 200 cycles SnO₂ thin film has shown highest sensitivity to CO gas than other films. A correlation between the characteristics of Sn3d_5/2 and O1s XPS spectra before and after annealing and the electrical behavior of the SnO₂ thin films is established.     

Preparation and characterization of nitrogen-incorporated SnO2 films

Nitrogen-incorporated SnO₂ thin films have been grown on Si(100) and quartz substrates by reactive sputtering of a Sn target in gas mixtures of N₂–O₂. The structure of the nitrogen-incorporated SnO₂ thin films was studied by X-ray diffraction, and the changes in the chemical bonds and atomic binding states of the nitrogen-incorporated SnO₂ thin films were analyzed by X-ray photoelectron spectroscopy. It was found that the binding energy of Sn 3d and O 1s shifts 0.65 eV and 0.35 eV, respectively, toward the lower-energy side after nitrogen was incorporated into the SnO₂ thin films as a comparison with that of pure SnO₂ film. The indirect optical band gap gradually decreases from 3.42 eV to 3.23 eV, i.e. from the UV to the edge of the visible-light range, with increasing nitrogen flux content in the N₂–O₂ gas mixtures. PACS 81.15.Cd; 78.20.-e; 68.37.Xy; 81.05.Je     

择优取向MgO缓冲层上制备的硅基Ba0.7Sr0.3TiO3薄膜的结构和性能研究

分别采用sol-gel法和磁控溅射法在Si（001）单晶衬底上制备出（111）和（001）取向的MgO缓冲层薄膜,随后在其上生长Ba_0.7Sr_0.3TiO₃（BST30）铁电薄膜.通过X射线衍射,扫描电子显微镜,原子力显微镜等方法研究了薄膜的微结构.实验结果发现,在较厚的MgO（001）缓冲层上可长出（101）取向的BST30薄膜,而在较薄的MgO（111） 缓冲层上则表现出（101）和（111）取向相互竞争的现象,随着MgO（111）缓冲 关键词： 0.7Sr_0.3TiO₃')" href="#">Ba_0.7Sr_0.3TiO₃ 铁电薄膜 择优取向 sol-gel     

Laser–MBE growth of high-quality ZnO thin films on Al2O3(0001) and SiO2/Si(100) using the third harmonics of a Nd:YAG laser

High-quality ZnO thin films were grown on single-crystalline Al₂O₃(0001) and amorphous SiO₂/Si(100) substrates at 400–640 °C using laser molecular beam epitaxy. For film growth, the third harmonics of a pulsed Nd:YAG laser were illuminated on a ZnO target. The ZnO films were epitaxially grown on Al₂O₃(0001) with the narrow X-ray diffraction full width at half maximum (FWHM) of 0.04° and the films on SiO₂/Si(100) exhibited a preferred c-axis orientation. Furthermore, the films exhibited excellent optical properties in photoluminescence (PL) measurements with very sharp excitonic and weak deep-level emission peaks. At 15 K, PL FWHM values of the films grown on Al₂O₃(0001) and SiO₂/Si(100) were 3 and 18 meV, respectively. Received: 8 May 2001 / Accepted: 18 September 2001 / Published online: 20 December 2001